Anpec APX9268XI-TRL Single-phase full-wave motor driver for silent fan motor Datasheet

APX9268
Single-Phase Full-Wave Motor Driver for Silent Fan Motor
Features
General Description
•
•
Silent Driver
The APX9268 is a single phase full wave motor driver
for DC fan motor. The output signal of this IC is the
•
Low Supply Current
•
Single Phase Full Wave Fan Driver
amplified hall input signal. It is suitable for both game
machine and CPU cooler that need silent drivers. The
Built-in Lock Protection and Auto Restart Function
device is built-in lock protection. When fan is locked,
the device will enter the lockup protection mode. It is
(External Capacitor Unnecessary)
•
FG Output
•
Include Hall Bias Circuit
•
Built-in Thermal Protection Circuit
•
Lead Free and Green Devices Available
also with thermal shutdown function. In normal
operation, the supply current is less than 5mA. The
APX9268 is available in MSOP-8 package.
(RoHS Compliant)
Pin Configuration
Applications
•
Motor Drivers For Silent Fan Motors
OUT2
1
8
GND
IN+
2
7
OUT1
HB
3
6
VCC
IN-
4
5
FG
MSOP-8
Ordering and Marking Information
Package Code
X : MSOP - 8
Temperature Range
I : -40 to 105 °C
Handling Code
TR : Tape & Reel
Assembly Material
L : Lead Free Device
G : Halogen and Lead Free Device
APX9268
Assembly Material
Handling Code
Temperature Range
Package Code
APX9268 X :
A9268
XXX
XX
XXXXX - Date Code
Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which
are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020C for
MSL classification at lead-free peak reflow temperature. ANPEC defines “Green” to mean lead-free (RoHS compliant) and halogen
free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by
weight).
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and
advise customers to obtain the latest version of relevant information to verify before placing orders.
Copyright  ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
1
www.anpec.com.tw
APX9268
Absolute Maximum Ratings (Note 2)
Symbol
Parameter
Rating
Unit
VCC
VCC Pin Maximum Supply Voltage
7
V
IOUT
Output Pin Maximum Output Current
1
A
VOUT
Output Pin Output Supply Voltage
7
V
IHB
HB Pin Maximum Output Current
10
mA
VFG
FG Pin Maximum Output Voltage
7
V
IFG
FG Pin Maximum Output Current
10
mA
Thermal Resistance-Junction to Ambient MSOP8
225
°C/W
0.585
W
RTH, JA
(Note1)
PD
Power Dissipation
TJ
Junction Temperature
-40 to 150
°C
TSTG
Storage Temperature
-65 to 150
°C
TSDR
Maximum Lead Soldering Temperature, 10 Seconds
260
°C
Note1: Mounted on a board (60x38x1.6t mm, Glass epoxy)
Note2: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Recommended Operating Conditions
Symbol
Parameter
Ratings
Unit
VCC
VCC Pin Supply Voltage
2 to 5.5
V
VHall
Hall Input Voltage Range
0.4 to Vcc-1.1
V
-40 to 105
°C
TA
Ambient Temperature
Electrical Characteristics (VCC=5V, TA=25°C)
Symbol
VHB
ICC1
ICC2
Parameter
Hall Bias Voltage
Supply Current
Test Conditions
APX9268
Unit
Min.
Typ.
Max.
IHB = 0 ~ 5mA
1.1
1.3
1.5
V
Rotation Mode
-
3.5
5
mA
Lock Protection Mode
-
3.5
5
mA
VHOFS
Input Offset Voltage
-
-
±6
mV
GIO
Input – Output Gain
45
48
51
dB
TON
Lock Detection On Time
0.35
0.5
0.65
sec
TOFF
Lock Detection Off Time
3.5
5
6.5
sec
VOL
Output Lower Side Voltage
IOUT = 250mA
-
0.15
0.22
V
VOH
Output Upper Side Voltage
IOUT = 250mA
-
0.15
0.22
V
VFG
FG Pin Low Voltage
IFG = 3mA
-
0.2
0.3
V
IFG
FG Pin Leak Current
VFG = 5V
-
-
1
µA
Copyright  ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
2
www.anpec.com.tw
APX9268
Electrical Characteristics (Cont.)
Symbol
VHYS
Parameter
(VCC=5V, TA=25°C)
APX9268
Test Conditions
Input Hysteresis Voltage
Over Temperature Shutdown
Over Temperature Shutdown
Hysteresis
Min.
Typ.
Max.
±5
±10
±15
-
175
-
-
25
-
Unit
mV
°C
Truth Table
Input
Output
IN-
IN+
OUT1
OUT2
FG
Mode
L
H
H
L
L
H
L
L
H
OFF
H
L
L
L
OFF
L
H
L
L
L
Operation Mode
Lock Protection Mode
Typical Operating Characteristics
FG Pin Current vs. Low Voltage
4.5
10
4
9
Operation mode
3.5
FG Pin Current (mA)
VCC Supply Current (mA)
VCC Supply Current vs. VCC Supply Voltage
3
2.5
2
Lock Protection Mode
1.5
8
7
6
5
4
3
1
2
0.5
1
0
0
0
1
2
3
4
5
6
0
0.4
0.6
0.8
FG Pin Low Voltage (V)
VCC Supply Voltage (V)
Copyright  ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
0.2
3
www.anpec.com.tw
APX9268
Typical Operating Characteristics (Cont.)
Offset Voltage vs. Ambient Temperature
Output Voltage vs. Output Current
1.4
1
Output Voltage (V)
Offset Voltage (mV)
1.2
0.8
0.6
0.4
0.2
0
-40
-20
0
20
40
60
80
1.2
1.1
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Upper Side Voltage
Low Side Voltage
0 100 200 300 400 500 600 700 800 900 1000
Ambient Temperature (°C)
Output Current (mA)
HB Voltage vs. VCC Supply Voltage
700
1.4
600
1.2
500
1
HB Voltage (V)
Maximum Power Dissipation (mW)
Maximum Power Dissipation vs.
Ambient Temperature
400
300
200
100
0.8
0.6
0.4
0.2
0
0
25
50
75
100
125
IHB =5mA
0
150
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
Ambient Temperature (°C)
Copyright  ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
IHB =0mA
VCC Supply Voltage (V)
4
www.anpec.com.tw
APX9268
Operating Waveforms
Rotation Mode Waveform1
Rotation Mode Waveform2
VIN-(50mV/div)
VOUT1(2V/div)
VIN+(50mV/div)
VOUT2(2V/div)
VOUT1(2V/div)
VFG(5V/div)
VOUT2(2V/div)
IOUT (0.5A/div)
Time (1ms/div)
Time (1ms/div)
Lock Protection Waveform2
Lock Protection Waveform1
TON
Lock
TOFF
VOUT1(2V/div)
VOUT1(2V/div)
VOUT2(2V/div)
VOUT2(2V/div)
VFG(5V/div)
IOUT (0.5A/div)
IOUT (0.5A/div)
Time (1s/div)
Time (0.1s/div)
Copyright  ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
5
www.anpec.com.tw
APX9268
Operating Waveforms (Cont.)
Lock Protection Waveform3
Release
VOUT1(2V/div)
VOUT2(2V/div)
VFG(5V/div)
IOUT (0.5A/div)
Time (50ms/div)
Pin Description
PIN
Description
No.
Name
1
OUT2
2
IN+
Hall Input +
3
HB
Hall Bias
4
IN-
Hall Input -
5
FG
FG signal output terminal
6
VCC
Supply Voltage
7
OUT1
H-bridge output connection. The output stage is a H-bridge formed by four
transistors and four-protection diode for switching applications.
8
GND
Power GND.
H-bridge output connection. The output stage is a H-bridge formed by four
transistors and four-protection diode for switching applications.
Copyright  ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
6
www.anpec.com.tw
APX9268
Block Diagram
150kΩ
OSC
VCC
GND
500Ω
+
OUT1
Lock
Detection
TSD
IN+
+
-
IN -
OUT2
500Ω
Hall
HB
150kΩ
Bias
FG
_
+
Typical Application Circuit
OUT2
GND
1
8
IN+
OUT1
2
7
HB
3
Hall
D2
Zener
VCC
D1
VIN
6
6V
IN-
FG
4
5
C1
RFG = 10kΩ
R1
Pull High
Voltage
Note 3: In hot plug application, it’s necessary to protect against a hot plug input voltage overshoot by adding an input
zener diode between the VCC and GND to clamp the overshoot. In normal operation, the zener diode isn’t
stressed because output current doesn’t reverse to VCC.
Copyright  ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
7
www.anpec.com.tw
APX9268
Function Description
Lockup Protection and Automatic Restart
The linear output architecture is used as output driver.
The APX9268 provides the lockup protection and automatic restart functions for preventing the coil burn-
Frequency Generator Function
out in the fan is locked. This IC has an internal counter
to determine the shutdown time (TOFF) and restart time
The FG pin is an open collector output, connecting a pull
up resistor to a high level voltage for the frequency
(TON). During shutdown time, the output drivers keep turning off for 5 seconds and then enter the restart time. Dur-
generator function.
When IN- is larger than IN+, FG is high (switch off); when
IN- is smaller than IN+, FG is low (switch on). Open the
ing the restart time, one output is high and the other is
low, which makes a torque for fan rotation. The restart
terminal when not in using.
time has 0.5 second.
Thermal Protection
If the locked condition is not removed, the shutdown/
restart process will be recurred until the locked condi-
The APX9268 has thermal protection. When internal
tion is released (See Figure 1 Lockup/Auto Restart
junction temperature reaches 175°C, the output devices will
be switched off. When the IC’s junction temperature cools
Waveform).
by 25°C, the thermal sensor will turn the output devices on
again, resulting in a pulsed output during continuous
Output Drivers
thermal protection.
All four drivers in the bridge output are designed for
single phase full wave motor driver for fan motor.
ININ+
TOFF
TOFF
OUT1
TON
OUT2
FG
Lock
Lock
Detection
Release
Reset
Figure 1 Lockup /Auto Restart Waveform
Copyright  ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
8
www.anpec.com.tw
APX9268
Application Information
Input Protection Diode & Zener Diode & Capacitor
FG Resistor
It should be added a protection diode (D1) to protect the
The value of the FG resistor could be decided by the fol-
damage from the power reverse connection. However,
the protection diode will cause a voltage drop on the
lowing equation:
−
RFG = V CC V FG
IFG
supply voltage. The current rating of the diode must be
larger than the maximum output current. Connecting
For example:
VCC and GND with a Zener diode (D2) can avoid exceeding the absolute maximum rating voltage. For the noise
VCC = 5V, IFG = 3mA, VFG = 0.2V, RFG = 1.6KΩ
reduction purpose, there is a capacitor (C1) 1µF
(recommended) connecting VCC and GND (See Typical
The value of resistor in the range of 1kΩ to 10kΩ is
recommended.
Application Circuit).
Thermal Consideration
Hall input
The IC is safe to operate below the line and it will cause
The output signal of this IC is the amplified hall input
signal, therefore, the output signal depends on hall input.
the thermal protection if the operating area is above the
When the hall input is small, the output signal becomes
gentle. Oppositely, the input signal is large, the output
line. For example, TA= 75°C, the maximum power dis-
becomes steep (See Figure 2 Different of output signal depending on the shape of hall input signal). The
vs. Ambient Temperature). Mounted on a board, there is
input/output gain is 48dB(typ.). Thus, please adjust the
amplitude of hall input to meet the adequate output
be calculated by the following equation:
sipation is about 0.35W (See Power Dissipation
60x38x1.6t mm, Glass epoxy. The power dissipation can
PD = (VCC - VOH + VOL) x IOUT + VCC x ICC
voltage.
For example:
(IN+)-(IN-)
If
VCC = 5V, ICC = 4mA, IOUT = 270mA, VOH = 4.83V,
VOL = 0.17V,
then
PD = 0.111W
OUT1
The GND pin provides an electrical connection to ground
and channeling heat away. The printed circuit board (PCB)
forms a heat sink and dissipates most of the heat into
ambient air.
(IN+)-(IN-)
OUT1
Figure 2 Different of output signal depending on the
shape
Copyright  ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
9
www.anpec.com.tw
APX9268
Package Information
MSOP-8
D
b
0.25
A
A1
A2
c
L
GAUGE PLANE
SEATING PLANE
0
e
E
E1
SEE VIEW A
VIEW A
S
Y
M
B
O
L
MSOP-8
MILLIMETERS
MIN.
INCHES
MAX.
A
MIN.
MAX.
1.10
0.043
0.15
0.000
0.006
0.75
0.95
0.030
0.037
b
0.22
0.38
0.009
0.015
A1
A2
0.00
c
0.08
0.23
0.003
0.009
D
2.90
3.10
0.114
0.122
E
4.70
5.10
0.185
0.201
E1
2.90
3.10
0.114
0.122
e
0.65 BSC
0.026 BSC
L
0.40
0.80
0.016
0.031
0
0°
8°
0°
8°
Note: 1. Follow JEDEC MO-187 AA.
2. Dimension “D”does not include mold flash, protrusions or gate
burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil
per side.
3. Dimension “E1”does not include inter-lead flash or protrusions.
Inter-lead flash and protrusions shall not exceed 5 mil per side.
Copyright  ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
10
www.anpec.com.tw
APX9268
Carrier Tape & Reel Dimensions
P0
P2
P1
A
B0
W
F
E1
OD0
K0
A0
A
OD1 B
B
T
SECTION A-A
SECTION B-B
H
A
d
T1
Application
MSOP- 8
A
H
T1
C
d
12.4+2.00 13.0+0.50
330.0±2.00 50 MIN.
1.5 MIN.
-0.00
-0.20
P0
P1
P2
D0
D1
1.5+0.10
4.00±0.10 8.00±0.10 2.00±0.10
1.5 MIN.
-0.00
D
W
E1
20.2 MIN. 12.0±0.30 1.75±0.10
F
5.5±0.10
T
A0
B0
K0
0.6+0.00
6.70±0.20 3.30±0.20 1.40±0.20
-0.40
(mm)
Devices Per Unit
Package Type
Unit
Quantity
MSOP- 8
Tape & Reel
3000
Copyright  ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
11
www.anpec.com.tw
APX9268
Reflow Condition
(IR/Convection or VPR Reflow)
tp
TP
Critical Zone
TL to TP
Ramp-up
Temperature
TL
tL
Tsmax
Tsmin
Ramp-down
ts
Preheat
25
t 25°C to Peak
Time
Reliability Test Program
Test item
SOLDERABILITY
HOLT
PCT
TST
ESD
Latch-Up
Method
MIL-STD-883D-2003
MIL-STD-883D-1005.7
JESD-22-B,A102
MIL-STD-883D-1011.9
MIL-STD-883D-3015.7
JESD 78
Description
245°C, 5 sec
1000 Hrs Bias @125°C
168 Hrs, 100%RH, 121°C
-65°C~150°C, 200 Cycles
VHBM > 2KV, VMM > 200V
10ms, 1tr > 100mA
Classification Reflow Profiles
Profile Feature
Average ramp-up rate
(TL to TP)
Preheat
- Temperature Min (Tsmin)
- Temperature Max (Tsmax)
- Time (min to max) (ts)
Time maintained above:
- Temperature (TL)
- Time (tL)
Peak/Classification Temperature (Tp)
Time within 5°C of actual
Peak Temperature (tp)
Ramp-down Rate
Time 25°C to Peak Temperature
Sn-Pb Eutectic Assembly
Pb-Free Assembly
3°C/second max.
3°C/second max.
100°C
150°C
60-120 seconds
150°C
200°C
60-180 seconds
183°C
60-150 seconds
217°C
60-150 seconds
See table 1
See table 2
10-30 seconds
20-40 seconds
6°C/second max.
6°C/second max.
6 minutes max.
8 minutes max.
Note: All temperatures refer to topside of the package. Measured on the body surface.
Copyright  ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
12
www.anpec.com.tw
APX9268
Classification Reflow Profiles (Cont.)
Table 1. SnPb Eutectic Process – Package Peak Reflow Temperatures
3
3
Package Thickness
<2.5 mm
≥2.5 mm
Volume mm
≥350
225 +0/-5°C
225 +0/-5°C
Volume mm
<350
240 +0/-5°C
225 +0/-5°C
Table 2. Pb-free Process – Package Classification Reflow Temperatures
3
3
3
Volume mm
Volume mm
Volume mm
<350
350-2000
>2000
<1.6 mm
260 +0°C*
260 +0°C*
260 +0°C*
1.6 mm – 2.5 mm
260 +0°C*
250 +0°C*
245 +0°C*
≥2.5 mm
250 +0°C*
245 +0°C*
245 +0°C*
* Tolerance: The device manufacturer/supplier shall assure process compatibility up to and including the stated
classification temperature (this means Peak reflow temperature +0°C. For example 260°C+0°C) at the rated MSL
level.
Package Thickness
Customer Service
Anpec Electronics Corp.
Head Office :
No.6, Dusing 1st Road, SBIP,
Hsin-Chu, Taiwan, R.O.C.
Tel : 886-3-5642000
Fax : 886-3-5642050
Taipei Branch :
2F, No. 11, Lane 218, Sec 2 Jhongsing Rd.,
Sindian City, Taipei County 23146, Taiwan
Tel : 886-2-2910-3838
Fax : 886-2-2917-3838
Copyright  ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
13
www.anpec.com.tw
Similar pages