DS90UB901Q/DS90UB902Q 10 - 43MHz 14 Bit Color FPD-Link III Serializer and Deserializer with Bidirectional Control Channel General Description The DS90UB901Q/DS90UB902Q chipset offers a FPD-Link III interface with a high-speed forward channel and a bidirectional control channel for data transmission over a single differential pair. The Serializer/Deserializer pair is targeted for direct connections between automotive camera systems and Host Controller/Electronic Control Unit (ECU). The primary transport sends 16 bits of image data over a single high-speed serial stream together with a low latency bidirectional control channel transport that supports I2C. Included with the 16-bit payload is a selectable data integrity option for CRC (Cyclic Redundancy Check) to monitor transmission link errors. Using TI’s embedded clock technology allows transparent fullduplex communication over a single differential pair, carrying asymmetrical bidirectional control information without the dependency of video blanking intervals. This single serial stream simplifies transferring a wide data bus over PCB traces and cable by eliminating the skew problems between parallel data and clock paths. This significantly saves system cost by narrowing data paths that in turn reduce PCB layers, cable width, and connector size and pins. In addition, the Deserializer inputs provide equalization control to compensate for loss from the media over longer distances. Internal DC balanced encoding/decoding is used to support AC-Coupled interconnects. A Serializer standby function provides a low power-savings mode with a remote wake up capability for signaling of a remote device. The Serializer is offered in a 32-pin LLP (5mm x 5mm) package, and Deserializer is offered in a 40-pin LLP (6mm x 6mm) package. Features ■ 10 MHz to 43 MHz input PCLK support ■ 160 Mbps to 688 Mbps data throughput ■ Single differential pair interconnect ■ Bidirectional control interface channel with I2C support ■ Embedded clock with DC Balanced coding to support AC■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ coupled interconnects Capable to drive up to 10 meters shielded twisted-pair I2C compatible serial interface Single hardware device addressing pin 16–bit data payload with CRC (Cyclic Redundancy Check) for checking data integrity Up to 6 Programmable GPIO's LOCK output reporting pin and AT-SPEED BIST diagnosis feature to validate link integrity Integrated termination resistors 1.8V- or 3.3V-compatible parallel bus interface Single power supply at 1.8V ISO 10605 ESD and IEC 61000-4-2 ESD compliant Automotive grade product: AEC-Q100 Grade 2 qualified Temperature range −40°C to +105°C No reference clock required on Deserializer Programmable Receive Equalization EMI/EMC Mitigation — DES Programmable Spread Spectrum (SSCG) outputs — DES Receiver staggered outputs Applications ■ ■ ■ ■ ■ Automotive Vision Systems Rear View, Side View Camera Lane Departure Warning Parking Assistance Blind Spot View Typical Application Diagram 30113527 FIGURE 1. Typical Application Circuit TRI-STATE® is a registered trademark of National Semiconductor Corporation. © 2012 Texas Instruments Incorporated 301135 SNLS322D www.ti.com DS90UB901Q/DS90UB902Q 10 - 43MHz 14 Bit Color FPD-Link III Serializer and Deserializer with Bidirectional Control Channel April 25, 2012 DS90UB901Q/DS90UB902Q Block Diagrams 30113528 FIGURE 2. Block Diagram 30113529 FIGURE 3. Application Block Diagram www.ti.com 2 NSID Quantity SPEC Package ID DS90UB901QSQE Package Description 32–pin LLP, 5.0 X 5.0 X 0.8 mm, 0.5 mm pitch 250 NOPB SQA32A DS90UB901QSQ 32–pin LLP, 5.0 X 5.0 X 0.8 mm, 0.5 mm pitch 1000 NOPB SQA32A DS90UB901QSQX 32–pin LLP, 5.0 X 5.0 X 0.8 mm, 0.5 mm pitch 2500 NOPB SQA32A DS90UB902QSQE 40–pin LLP, 6.0 X 6.0 X 0.8 mm, 0.5 mm pitch 250 NOPB SQA40A DS90UB902QSQ 40–pin LLP, 6.0 X 6.0 X 0.8 mm, 0.5 mm pitch 1000 NOPB SQA40A DS90UB902QSQX 40–pin LLP, 6.0 X 6.0 X 0.8 mm, 0.5 mm pitch 2500 NOPB SQA40A Note: Automotive Grade (Q) product incorporates enhanced manufacturing and support processes for the automotive market, including defect detection methodologies. Reliability qualification is compliant with the requirements and temperature grades defined in the AEC Q100 standard. Automotive Grade products are identified with the letter Q. For more information go to http://www.ti.com/automotive. DS90UB901Q Pin Diagram 30113519 Serializer - DS90UB901Q — Top View 3 www.ti.com DS90UB901Q/DS90UB902Q Ordering Information DS90UB901Q/DS90UB902Q DS90UB901Q Serializer Pin Descriptions Pin Name Pin No. I/O, Type Description LVCMOS PARALLEL INTERFACE DIN[13:0] 32, 31, 30, 29, Inputs, LVCMOS Parallel data inputs. 27, 26, 24, 23, w/ pull down 22, 21, 20, 19, 18, 17 HSYNC 1 Inputs, LVCMOS Horizontal SYNC Input w/ pull down VSYNC 2 Inputs, LVCMOS Vertical SYNC Input w/ pull down PCLK 3 Input, LVCMOS Pixel Clock Input Pin. Strobe edge set by TRFB control register. w/ pull down GENERAL PURPOSE INPUT OUTPUT (GPIO) DIN[3:0]/ GPIO[5:2] 20, 19, 18, 17 Input/Output, LVCMOS DIN[3:0] general-purpose pins can be individually configured as either inputs or outputs; used to control and respond to various commands. GPIO[1:0] 16, 15 Input/Output, LVCMOS General-purpose pins can be individually configured as either inputs or outputs; used to control and respond to various commands. BIDIRECTIONAL CONTROL BUS - I2C COMPATIBLE SCL 4 Input/Output, Open Drain Clock line for the bidirectional control bus communication SCL requires an external pull-up resistor to VDDIO. SDA 5 Input/Output, Open Drain Data line for the bidirectional control bus communication SDA requires an external pull-up resistor to VDDIO. MODE 8 ID[x] 6 I2C Mode select MODE = L, Master mode (default); Device generates and drives the SCL clock line. Device is connected to slave peripheral on the bus. (Serializer initially starts up in Input, LVCMOS Standby mode and is enabled through remote wakeup by Deserializer) w/ pull down MODE = H, Slave mode; Device accepts SCL clock input and attached to an I2C controller master on the bus. Slave mode does not generate the SCL clock, but uses the clock generated by the Master for the data transfers. Input, analog Device ID Address Select Resistor to Ground and 10 kΩ pull-up to 1.8V rail. See Table 3 CONTROL AND CONFIGURATION PDB 9 Power down Mode Input Pin. PDB = H, Serializer is enabled and is ON. Input, LVCMOS PDB = L, Serailizer is in Power Down mode. When the Serializer is in Power Down, w/ pull down the PLL is shutdown, and IDD is minimized. Programmed control register data are NOT retained and reset to default values RES 7 Input, LVCMOS Reserved. w/ pull down This pin MUST be tied LOW. FPD-LINK III INTERFACE DOUT+ 13 DOUT- 12 Input/Output, CML Non-inverting differential output, bidirectional control channel input. The interconnect must be AC Coupled with a 100 nF capacitor. Input/Output, CML Inverting differential output, bidirectional control channel input. The interconnect must be AC Coupled with a 100 nF capacitor. POWER AND GROUND VDDPLL 10 Power, Analog PLL Power, 1.8V ±5% VDDT 11 Power, Analog Tx Analog Power, 1.8V ±5% VDDCML 14 Power, Analog CML & Bidirectional Channel Driver Power, 1.8V ±5% VDDD 28 Power, Digital Digital Power, 1.8V ±5% www.ti.com 4 VDDIO VSS Pin No. 25 I/O, Type Description Power, Digital Power for I/O stage. The single-ended inputs and SDA, SCL are powered from VDDIO. VDDIO can be connected to a 1.8V ±5% or 3.3V ±10% Ground, DAP DAP must be grounded. DAP is the large metal contact at the bottom side, located at the center of the LLP package. Connected to the ground plane (GND) with at least 9 vias. DAP DS90UB902Q Pin Diagram 30113520 Deserializer - DS90UB902Q — Top View 5 www.ti.com DS90UB901Q/DS90UB902Q Pin Name DS90UB901Q/DS90UB902Q DS90UB902Q Deserializer Pin Descriptions Pin Name Pin No. I/O, Type Description LVCMOS PARALLEL INTERFACE ROUT[13:0] 9, 10, 11, 12, 14, 15, 17, 18, 19, 20, 21, 22, 23, 24 Outputs, LVCMOS Parallel data outputs. HSYNC 7 Output, LVCMOS Horizontal SYNC Output VSYNC 6 Output, LVCMOS Vertical SYNC Output PCLK 5 Output, LVCMOS Pixel Clock Output Pin. Strobe edge set by RRFB control register. GENERAL PURPOSE INPUT OUTPUT (GPIO) ROUT[3:0] / GPIO[5:2] GPIO[1:0] 21, 22, 23, 24 Input/Output, LVCMOS ROUT[3:0] general-purpose pins can be individually configured as either inputs or outputs; used to control and respond to various commands. 26, 27 Input/Output, LVCMOS General-purpose pins can be individually configured as either inputs or outputs; used to control and respond to various commands. BIDIRECTIONAL CONTROL BUS - I2C COMPATIBLE SCL 3 Input/Output, Open Drain Clock line for the bidirectional control bus communication SCL requires an external pull-up resistor to VDDIO. SDA 2 Input/Output, Open Drain Data line for bidirectional control bus communication SDA requires an external pull-up resistor to VDDIO. I2C Mode select MODE 40 ID[x] 1 MODE = L, Master mode; Device generates and drives the SCL clock line, where Input, LVCMOS required such as Read. Device is connected to slave peripheral on the bus. w/ pull up MODE = H, Slave mode (default); Device accepts SCL clock input and attached to an I2C controller master on the bus. Slave mode does not generate the SCL clock, but uses the clock generated by the Master for the data transfers. Input, analog Device ID Address Select Resistor to Ground and 10 kΩ pull-up to 1.8V rail. See Table 4 CONTROL AND CONFIGURATION 29 Power down Mode Input Pin. PDB = H, Deserializer is enabled and is ON. Input, LVCMOS PDB = L, Deserializer is in Power Down mode. When the Deserializer is in Power w/ pull down Down. Programmed control register data are NOT retained and reset to default values. LOCK 28 Output, LVCMOS LOCK Status Output Pin. LOCK = H, CDR/PLL is Locked, outputs are active LOCK = L, CDR/PLL is unlocked, the LVCMOS Outputs depend on OSS_SEL control register, the CDR/PLL is shutdown and IDD is minimized. May be used as Link Status. PASS 31 Output, LVCOMS When BISTEN = L; Normal operation PASS is high to indicate no errors are detected. The PASS pin asserts low to indicate a CRC error was detected on the Link. - Reserved Pin 39: This pin MUST be tied LOW. Pins 32,33: Route to test point or leave open if unused. See also FPD-LINK III INTERFACE pin description section. PDB RES 32, 33, 39 BIST MODE BISTEN www.ti.com 37 BIST Enable Pin. Input, LVCMOS BISTEN = H, BIST Mode is enabled. w/ pull down BISTEN = L, BIST Mode is disabled. 6 PASS Pin No. I/O, Type 31 Output, LVCOMS Description PASS Output Pin for BIST mode. PASS = H, ERROR FREE Transmission PASS = L, one or more errors were detected in the received payload. Leave Open if unused. Route to test point (pad) recommended. FPD-LINK III INTERFACE RIN+ 35 Input/Output, CML Non-inverting differential input, bidirectional control channel output. The interconnect must be AC Coupled with a 100 nF capacitor. RIN- 36 Input/Output, CML Inverting differential input, bidirectional control channel output. The interconnect must be AC Coupled with a 100 nF capacitor. CMLOUTP 32 Output, CML Non-inverting CML Output Monitor point for equalized differential signal. Test port is enabled via control registers. CMLOUTN 33 Output, CML Inverting CML Output Monitor point for equalized differential signal. Test port is enabled via control registers. POWER AND GROUND VDDSSCG 4 Power, Digital SSCG Power, 1.8V ±5% Power supply must be connected regardless if SSCG function is in operation. VDDIO1/2/3 25, 16, 8 Power, Digital LVTTL I/O Buffer Power, The single-ended outputs and control input are powered from VDDIO. VDDIO can be connected to a 1.8V ±5% or 3.3V ±10% VDDD 13 Power, Digital Digital Core Power, 1.8V ±5% VDDR 30 Power, Analog Rx Analog Power, 1.8V ±5% VDDCML 34 Power, Analog Bidirectional Channel Driver Power, 1.8V ±5% VDDPLL 38 Power, Analog PLL Power, 1.8V ±5% DAP Ground, DAP DAP must be grounded. DAP is the large metal contact at the bottom side, located at the center of the LLP package. Connected to the ground plane (GND) with at least 16 vias. VSS 7 www.ti.com DS90UB901Q/DS90UB902Q Pin Name DS90UB901Q/DS90UB902Q Air Discharge (DOUT+, DOUT-, RIN+, RIN-) Contact Discharge (DOUT+, DOUT-, RIN+, RIN-) ESD Rating (HBM) Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. Supply Voltage – VDDn (1.8V) Supply Voltage – VDDIO LVCMOS Input Voltage I/O Voltage CML Driver I/O Voltage (VDD) CML Receiver I/O Voltage (VDD) Junction Temperature Storage Temperature Maximum Package Power Dissipation Capacity Package Package Derating: DS90UB901Q 32L LLP −0.3V to +2.5V −0.3V to +4.0V For soldering specifications: see product folder at www.ti.com Recommended Operating Conditions 1/θJA °C/W above +25° θJC (based on 9 thermal vias) DS90UB902Q 40L LLP 6.9 °C/W Supply Voltage (VDDn) LVCMOS Supply Voltage (VDDIO) OR LVCMOS Supply Voltage (VDDIO) Supply Noise VDDn (1.8V) VDDIO (1.8V) VDDIO (3.3V) Operating Free Air Temperature (TA) PCLK Clock Frequency 28.0 °C/W θJA (based on 16 thermal vias) 4.4 °C/W θJC (based on 16 thermal vias) ESD Rating (IEC 61000-4-2) RD = 330Ω, CS = 150pF Air Discharge (DOUT+, DOUT-, RIN+, RIN-) Contact Discharge (DOUT+, DOUT-, RIN+, RIN-) ESD Rating (ISO10605) RD = 330Ω, CS = 150/330pF ESD Rating (ISO10605) RD = 2KΩ, CS = 150/330pF ≥±25 kV ≥±10 kV Electrical Characteristics ≥±8 kV ≥±1 kV ≥±250 V ESD Rating (MM) −0.3V to (VDD + 0.3V) +150°C −65°C to +150°C 34.3 °C/W ≥±10 kV ESD Rating (CDM) −0.3V to + (VDDIO + 0.3V) −0.3V to +(VDD + 0.3V) θJA (based on 9 thermal vias) ≥±15 kV Min 1.71 Nom 1.8 Max 1.89 Units V 1.71 1.8 1.89 V 3.0 3.3 3.6 V 25 25 50 mVp-p mVp-p mVp-p +105 °C 43 MHz -40 +25 10 (Note 2, Note 3, Note 4) Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units LVCMOS DC SPECIFICATIONS 3.3V I/O (SER INPUTS, DES OUTPUTS, GPIO, CONTROL INPUTS AND OUTPUTS) VIH High Level Input Voltage VIN = 3.0V to 3.6V 2.0 VIN V VIL Low Level Input Voltage VIN = 3.0V to 3.6V GND 0.8 V IIN Input Current VIN = 0V or 3.6V VIN = 3.0V to 3.6V -20 +20 µA VOH High Level Output Voltage VDDIO = 3.0V to 3.6V IOH = -4 mA 2.4 VDDIO V VOL Low Level Output Voltage VDDIO = 3.0V to 3.6V IOL = +4 mA GND 0.4 V IOS Output Short Circuit Current VOUT = 0V IOZ TRI-STATE® Output Current PDB = 0V, VOUT = 0V or VDD ±1 Serializer GPIO Outputs -24 Deserializer LVCMOS Outputs -39 LVCMOS Outputs mA -20 ±1 +20 µA LVCMOS DC SPECIFICATIONS 1.8V I/O (SER INPUTS, DES OUTPUTS, GPIO, CONTROL INPUTS AND OUTPUTS) VIH High Level Input Voltage VIN = 1.71V to 1.89V 0.65 VIN VIN +0.3 VIL Low Level Input Voltage VIN = 1.71V to 1.89V GND 0.35 VIN www.ti.com 8 V Parameter Conditions Min Typ Max Units -20 ±1 +20 µA VDDIO 0.45 VDDIO V GND 0.45 V IIN Input Current VIN = 0V or 1.89V VIN = 1.71V to 1.89V VOH High Level Output Voltage VDDIO = 1.71V to 1.89V IOH = −2 mA Serializer GPIO Outputs VDDIO = 1.71V to 1.89V IOH = −4 mA Deserializer LVCMOS Outputs VDDIO = 1.71V to 1.89V IOL = +2 mA Serializer GPIO Outputs VDDIO = 1.71V to 1.89V IOL = +4 mA Deserializer LVCMOS Outputs VOUT = 0V Serializer GPIO Outputs -11 Deserializer LVCMOS Outputs -20 VOL IOS IOZ Low Level Output Voltage Output Short Circuit Current TRI-STATE® Output Current PDB = 0V, VOUT = 0V or VDD LVCMOS Outputs mA -20 ±1 +20 µA 268 340 412 mV 1 50 mV CML DRIVER DC SPECIFICATIONS (DOUT+, DOUT-) |VOD| Output Differential Voltage RT = 100Ω (Figure 7) ΔVOD Output Differential Voltage Unbalance RL = 100Ω VOS Output Differential Offset Voltage RL = 100Ω (Figure 7) ΔVOS Offset Voltage Unbalance RL = 100Ω IOS Output Short Circuit Current DOUT+/- = 0V, RT Differential Internal Termination Resistance Differential across DOUT+ and DOUT- VDD (MIN) V VDD - VOD DD (MAX) VOD (MAX) VOD (MIN) V 1 mV 50 -27 80 100 mA 120 Ω CML RECEIVER DC SPECIFICATIONS (RIN+, RIN-) VTH Differential Threshold High Voltage (Figure 8) +90 mV VTL Differential Threshold Low Voltage VIN Differential Input Voltage Range RIN+ - RIN- Input Current VIN = VDD or 0V, VDD = 1.89V Differential Internal Termination Resistance Differential across RIN+ and RIN- IIN RT -90 180 mV -20 ±1 +20 µA 80 100 120 Ω 62 90 SER/DES SUPPLY CURRENT *DIGITAL, PLL, AND ANALOG VDD IDDT Serializer (Tx) VDDn Supply Current (includes load current) RT = 100Ω WORST CASE pattern (Figure 5) VDDn = 1.89V PCLK = 43 MHz Default Registers RT = 100Ω RANDOM PRBS-7 pattern IDDIOT Serializer (Tx) VDDIO Supply Current (includes load current) RT = 100Ω WORST CASE pattern (Figure 5) 9 mA 55 VDDIO = 1.89V PCLK = 43 MHz Default Registers 2 VDDIO = 3.6V PCLK = 43 MHz Default Registers 7 5 mA 15 www.ti.com DS90UB901Q/DS90UB902Q Symbol DS90UB901Q/DS90UB902Q Symbol IDDTZ IDDIOTZ IDDR Parameter Conditions Serializer (Tx) Supply Current PDB = 0V; All other Power-down LVCMOS Inputs = 0V Deserializer (Rx) VDDn VDDn = 1.89V Supply Current (includes load CL = 8 pF current) WORST CASE Pattern (Figure 5) Min Typ Max VDDn = 1.89V 370 775 VDDIO = 1.89V 55 125 VDDIO = 3.6V 65 135 60 96 PCLK = 43 MHz SSCG[3:0] = ON Default Registers VDDn = 1.89V PCLK = 43 MHz Default Registers CL = 8 pF RANDOM PRBS-7 Pattern IDDIOR IDDRZ IDDIORZ Deserializer (Rx) VDDIO VDDIO = 1.89V Supply Current (includes load CL = 8 pF current) WORST CASE Pattern (Figure 5) PCLK = 43 MHz Default Registers VDDIO = 3.6V CL = 8 pF WORST CASE Pattern PDB = 0V; All other LVCMOS Inputs = 0V Deserializer (Rx) Supply Current Power-down Units µA 53 mA 16 25 PCLK = 43 MHz Default Registers 38 64 VDDn = 1.89V 42 400 VDDIO = 1.89V 8 40 VDDIO = 3.6V 350 800 µA Recommended Serializer Timing for PCLK (Note 12) Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter tTCP Transmit Clock Period tTCIH Transmit Clock Input High Time tTCIL Transmit Clock Input Low Time tCLKT PCLK Input Transition Time (Figure 9) fOSC Internal oscillator clock source www.ti.com Conditions 10 MHz – 43 MHz Min Typ Max Units 23.3 T 100 ns 0.4T 0.5T 0.6T ns 0.4T 0.5T 0.6T ns 3 ns 0.5 25 10 MHz Over recommended operating supply and temperature ranges unless otherwise specified. Typ Max Units tLHT Symbol CML Low-to-High Transition Time Parameter RL = 100Ω (Figure 6) Conditions 150 330 ps tHLT CML High-to-Low Transition Time RL = 100Ω (Figure 6) 150 330 ps tDIS Data Input Setup to PCLK tDIH Serializer Data Inputs Data Input Hold from PCLK (Figure 10) tPLD Serializer PLL Lock Time RL = 100Ω (Note 5, Note 11) tSD Serializer Delay RT = 100Ω PCLK = 10–43 MHz Register 0x03h b[0] (TRFB = 1) (Figure 12) tJIND tJINR tJINT λSTXBW δSTX δSTXf Serializer Output Deterministic Jitter Min 2.0 ns 2.0 ns 6.386T +5 1 2 ms 6.386T + 12 6.386T + 19.7 ns Serializer output intrinsic deterministic jitter . Measured (cycle-cycle) with PRBS-7 test pattern PCLK = 43 MHz (Note 4, Note 13) 0.13 UI Serializer Output Random Jitter Serializer output intrinsic random jitter (cycle-cycle). Alternating-1,0 pattern. PCLK = 43 MHz (Note 4, Note 13) 0.04 UI Peak-to-peak Serializer Output Jitter Serializer output peak-to-peak jitter includes deterministic jitter, random jitter, and jitter transfer from serializer input. Measured (cycle-cycle) with PRBS-7 test pattern. PCLK = 43 MHz (Note 4, Note 13) 0.396 UI Serializer Jitter Transfer Function -3 dB Bandwidth PCLK = 43 MHz Default Registers (Figure 18) (Note 4) 1.90 MHz Serializer Jitter Transfer Function (Peaking) PCLK = 43 MHz Default Registers (Figure 18 ) (Note 4) 0.944 dB Serializer Jitter Transfer Function (Peaking Frequency) PCLK = 43 MHz Default Registers (Figure 18) (Note 4) 500 kHz 11 www.ti.com DS90UB901Q/DS90UB902Q Serializer Switching Characteristics DS90UB901Q/DS90UB902Q Deserializer Switching Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Pin/Freq. tRCP Receiver Output Clock Period tRCP = tTCP PCLK tPDC PCLK Duty Cycle Default Registers SSCG[3:0] = OFF PCLK tCLH tCHL tCLH tCHL LVCMOS Low-to-High Transition VDDIO: 1.71V to 1.89V or PCLK Time 3.0V to 3.6V, LVCMOS High-to-Low Transition CL = 8 pF (lumped load) Default Registers Time (Figure 14) (Note 10) LVCMOS Low-to-High Transition VDDIO: 1.71V to 1.89V or ROUT[13:0], Time HSYNC, VSYNC 3.0V to 3.6V, LVCMOS High-to-Low Transition CL = 8 pF (lumped load) Default Registers Time (Figure 14) (Note 10) tROS ROUT Setup Data to PCLK tROH ROUT Hold Data to PCLK VDDIO: 1.71V to 1.89V or ROUT[13:0], HSYNC, VSYNC 3.0V to 3.6V, CL = 8 pF (lumped load) Default Registers (Figure 16) Typ Max Units T 100 ns 45 50 55 % 1.3 2.0 2.8 1.3 2.0 2.8 1.6 2.4 3.3 1.6 2.4 3.3 0.38T 0.5T 0.38T 0.5T 4.571T +8 4.571T + 12 ns ns ns tDD Deserializer Delay Default Registers Register 0x03h b[0] (RRFB = 1) (Figure 15) tDDLT Deserializer Data Lock Time (Figure 13) (Note 5) 10 MHz–43 MHz tRJIT Receiver Input Jitter Tolerance (Figure 17, Figure 19) (Note 13, Note 14) 43 MHz tRCJ Receiver Clock Jitter PCLK SSCG[3:0] = OFF (Note 6, Note 10) 10 MHz PCLK SSCG[3:0] = OFF (Note 7, Note 10) 10 MHz Deserializer Cycle-to-Cycle Clock PCLK Jitter SSCG[3:0] = OFF (Note 8, Note 10) 10 MHz fdev Spread Spectrum Clocking Deviation Frequency 20 MHz–43 MHz ±0.5% to ±2.0% % fmod Spread Spectrum Clocking Modulation Frequency 20 MHz–43 MHz 9 kHz to 66 kHz kHz tDPJ tDCCJ www.ti.com Deserializer Period Jitter 10 MHz–43 MHz Min 23.3 43 MHz 43 MHz 43 MHz LVCMOS Output Bus SSC[3:0] = ON (Figure 20) 12 4.571T + 16 ns 10 ms 0.53 UI 300 550 120 250 425 600 320 480 320 500 300 500 ps ps ps Over recommended supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units 100 kHz RECOMMENDED INPUT TIMING REQUIREMENTS (Note 12) fSCL SCL Clock Frequency tLOW SCL Low Period tHIGH >0 fSCL = 100 kHz 4.7 µs SCL High Period 4.0 µs tHD:STA Hold time for a start or a repeated start condition 4.0 µs tSU:STA Set Up time for a start or a repeated start condition 4.7 µs tHD:DAT Data Hold Time tSU:DAT Data Set Up Time 250 tSU:STO Set Up Time for STOP Condition 4.0 tr SCL & SDA Rise Time 1000 tf SCL & SDA Fall Time 300 ns Cb Capacitive load for bus 400 pF 0 3.45 µs ns µs ns SWITCHING CHARACTERISTICS (Note 11) fSCL tLOW SCL Clock Frequency SCL Low Period Serializer MODE = 0 – R/W Register 0x05 = 0x40'h 100 Deserializer MODE = 0 – READ Register 0x06 b[6:4] = 0x00'h 100 Serializer MODE = 0 – R/W Register 0x05 = 0x40'h Deserializer MODE = 0 – READ Register 0x06 b[6:4] = 0x00'h Serializer MODE = 0 – R/W Register 0x05 = 0x40'h kHz 4.7 µs 4.0 µs tHIGH SCL High Period tHD:STA Hold time for a start or a repeated start Serializer MODE = 0 condition Register 0x05 = 0x40'h 4.0 µs tSU:STA Set Up time for a start or a repeated start condition 4.7 µs tHD:DAT Data Hold Time tSU:DAT Data Set Up Time tSU:STO Set Up Time for STOP Condition tf SCL & SDA Fall Time tBUF Bus free time between a stop and start Serializer MODE = 0 condition tTIMEOUT NACK Time out Deserializer MODE = 0 – READ Register 0x06 b[6:4] = 0x00'h Serializer MODE = 0 Register 0x05 = 0x40'h 0 Serializer MODE = 0 3.45 250 ns 4.0 µs 300 4.7 ns µs Serializer MODE = 1 1 Deserializer MODE = 1 Register 0x06 b[2:0]=111'b 25 13 µs ms www.ti.com DS90UB901Q/DS90UB902Q Bidirectional Control Bus AC Timing Specifications (SCL, SDA) - I2C Compliant (Figure 4) DS90UB901Q/DS90UB902Q 30113536 FIGURE 4. Bidirectional Control Bus Timing Bidirectional Control Bus DC Characteristics (SCL, SDA) - I2C Compliant Over recommended supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions VIH Input High Level SDA and SCL VIL Input Low Level Voltage SDA and SCL VHY Input Hysteresis SDA and SCL IOZ TRI-STATE Output Current PDB = 0V VOUT = 0V or VDD IIN Input Current CIN Input Pin Capacitance VOL Low Level Output Voltage Min Typ Max Units 0.7 x VDDIO VDDIO V GND 0.3 x VDDIO V >50 SDA or SCL, Vin = VDDIO or GND mV -20 ±1 +20 µA -20 ±1 +20 µA <5 pF SCL and SDA VDDIO = 3.0V IOL = 1.5 mA 0.36 V SCL and SDA VDDIO = 1.71V IOL = 1 mA 0.36 V Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional; the device should not be operated beyond such conditions. Note 2: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed. Note 3: Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground except VOD, ΔVOD, VTH and VTL which are differential voltages. Note 4: Typical values represent most likely parametric norms at 1.8V or 3.3V, TA = +25°C, and at the Recommended Operation Conditions at the time of product characterization and are not guaranteed. Note 5: tPLD and tDDLT is the time required by the serializer and deserializer to obtain lock when exiting power-down state with an active PCLK Note 6: tDCJ is the maximum amount of jitter measured over 30,000 samples based on Time Interval Error (TIE). Note 7: tDPJ is the maximum amount the period is allowed to deviate measured over 30,000 samples. Note 8: tDCCJ is the maximum amount of jitter between adjacent clock cycles measured over 30,000 samples. Note 9: Supply noise testing was done with minimum capacitors (as shown on Figures 37, 38) on the PCB. A sinusoidal signal is AC coupled to the VDDn (1.8V) supply with amplitude = 25 mVp-p measured at the device VDDn pins. Bit error rate testing of input to the Ser and output of the Des with 10 meter cable shows no error when the noise frequency on the Ser is less than 1 MHz. The Des on the other hand shows no error when the noise frequency is less than 750 kHz. Note 10: Specification is guaranteed by characterization and is not tested in production. Note 11: Specification is guaranteed by design. Note 12: Recommended Input Timing Requirements are input specifications and not tested in production. Note 13: UI – Unit Interval is equivalent to one ideal serialized data bit width. The UI scales with PCLK frequency. Note 14: tRJIT max (0.61UI) is limited by instrumentation and actual tRJIT of in-band jitter at low frequency (<2 MHz) is greater 1 UI. www.ti.com 14 DS90UB901Q/DS90UB902Q AC Timing Diagrams and Test Circuits 30113552 FIGURE 5. “Worst Case” Test Pattern 30113546 30113547 FIGURE 6. Serializer CML Output Load and Transition Times 15 www.ti.com DS90UB901Q/DS90UB902Q 30113548 30113530 FIGURE 7. Serializer VOD DC Diagram 30113534 FIGURE 8. Differential VTH/VTL Definition Diagram 30113516 FIGURE 9. Serializer Input Clock Transition Times www.ti.com 16 DS90UB901Q/DS90UB902Q 30113549 FIGURE 10. Serializer Setup/Hold Times 30113532 FIGURE 11. Serializer Data Lock Time 30113550 FIGURE 12. Serializer Delay 30113513 FIGURE 13. Deserializer Data Lock Time 17 www.ti.com DS90UB901Q/DS90UB902Q 30113514 FIGURE 14. Deserializer LVCMOS Output Load and Transition Times 30113511 FIGURE 15. Deserializer Delay 30113531 FIGURE 16. Deserializer Output Setup/Hold Times 30113558 FIGURE 17. Receiver Input Jitter Tolerance www.ti.com 18 DS90UB901Q/DS90UB902Q 30113562 FIGURE 18. Typical Serializer Jitter Transfer Function Curve at 43 MHz 30113559 FIGURE 19. Typical Deserializer Input Jitter Tolerance Curve at 43 MHz 30113535 FIGURE 20. Spread Spectrum Clock Output Profile 19 www.ti.com DS90UB901Q/DS90UB902Q TABLE 1. DS90UB901Q Control Registers Addr (Hex) 0 1 2 Name Bits Field 7:1 DEVICE ID 0 SER ID SEL 7:3 RESERVED I2C Device ID 0x00'h 0 VDDIO Control 0: Device ID is from ID[x] 1: Register I2C Device ID overrides ID[x] Reserved Standby mode control. Retains control register data. Supported only when MODE = 0 0: Enabled. Low-current Standby mode with wake-up capability. Suspends all clocks and functions. 1: Disabled. Standby and wake-up disabled RW 1 DIGITAL RESET0 RW 1: Resets the device to default register values. Does not 0 self clear affect device I2C Bus or Device ID 0 DIGITAL RESET1 RW 0 1: Digital Reset, retains all register values self clear Reset Reserved 7-bit address of Serializer; 0x58'h (1011_000X'b) default STANDBY 7:0 6 5 RESERVED RX CRC CHECKER ENABLE TX CRC GEN ENABLE VDDIO CONTOL 0x20'h RW RW RW Reserved 1 Back Channel CRC Enable 0: Disable 1: Enable For proper CRC operation, on Deserailizer 0x03h b[6] control register must be Enabled. 1 Foward Channel CRC Enable 0: Disable 1: Enable For proper CRC operation, on Deserailizer 0x03h b[7] control register must be Enabled. 1 Auto VDDIO detect Allows manual setting of VDDIO by register. 0: Disable 1: Enable (auto detect mode) VDDIO Mode 4 VDDIO MODE RW 1 VDDIO voltage set Only used when VDDIOCONTROL = 0 0: 1.8V 1: 3.3V I2C PassThrough 3 I2C PASSTHROUGH RW 1 I2C Pass-Through 0: Disabled 1: Enabled RESERVED 2 RESERVED 0 Reserved 1 Switch over to internal 25 MHz Oscillator clock in the absence of PCLK 0: Disable 1: Enable 1 Pixel Clock Edge Select: 0: Parallel Interface Data is strobed on the Falling Clock Edge. 1: Parallel Interface Data is strobed on the Rising Clock Edge. PCLK_AUTO TRFB www.ti.com 0xB0'h Description 2 CRC Fault Tolerant Transmission 4 Default RW 7 3 R/W CRC Transmission 1 0 PCLK_AUTO TRFB 7:6 RESERVED 5 CRC RESET 4:0 RESERVED RW RW 10'b RW 0 00000'b 20 Reserved 1: CRC Reset. Clears CRC Error counter. Reserved Name 5 I2C Bus Rate 6 DES ID Bits Field 7:0 I2C BUS RATE 7:1 DES DEV ID 0 RESERVED 7:1 SLAVE DEV ID R/W Default Description RW 0x40'h I2C SCL frequency is determined by the following: fSCL = 6.25 MHz / Register value (in decimal) 0x40'h = ~100 kHz SCL (default) Note: Register values <0x32'h are NOT supported. RW 0xC0'h RW 0x00'h Deserializer Device ID = 0x60'h (1100_000X'b) default Reserved Slave Device ID. Sets remote slave I2C address. 7 Slave ID 0 RESERVED 8 Reserved 7:0 RESERVED 0x00'h Reserved 9 Reserved 7:0 RESERVED 0x01'h Reserved A CRC Errors 7:0 CRC ERROR B0 R 0x00'h Number of CRC errors - 8 LSBs B CRC Errors 7:0 CRC ERROR B1 R 0x00'h Number of CRC errors - 8 MSBs Reserved 7:3 RESERVED 0x00'h Reserved PCLK Detect 2 PCLK DETECT R 0 1: Valid PCLK detected 0: Valid PCLK not detected CRC Check 1 DES ERROR R 0 1: CRC error during communication with Deserializer Cable Link Detect Status 0 LINK DETECT R 0 0: Cable link not detected 1: Cable link detected C D E F 10 11 GPIO[0] Config GPIO[1] Config GPIO[2] Config GPIO[3] Config GPIO[4] Config Reserved 7:4 RESERVED 0001'b Reserved 3:2 RESERVED 00'b Reserved 1 GPIO0 DIR RW 0 0: Output 1: Input 0 GPIO0 EN RW 1 0: TRI-STATE 1: Enabled 7:4 RESERVED 0000'b Reserved 3:2 RESERVED 00'b Reserved 1 GPIO1 DIR RW 0 0: Output 1: Input 0 GPIO1 EN RW 1 0: TRI-STATE 1: Enabled 7:4 RESERVED 0000'b Reserved 3:2 RESERVED 00'b Reserved 1 GPIO2 DIR RW 1 0: Output 1: Input 0 GPIO2 EN RW 1 0: TRI-STATE 1: Enabled 7:4 RESERVED 0000'b Reserved 3:2 RESERVED 00'b Reserved 1 GPIO3 DIR RW 1 0: Output 1: Input 0 GPIO3 EN RW 1 0: TRI-STATE 1: Enabled 7:4 RESERVED 0000'b Reserved 3:2 RESERVED 00'b Reserved 1 GPIO4 DIR RW 1 0: Output 1: Input 0 GPIO4 EN RW 1 0: TRI-STATE 1: Enabled 21 www.ti.com DS90UB901Q/DS90UB902Q Addr (Hex) DS90UB901Q/DS90UB902Q Addr (Hex) 12 13 www.ti.com Name GPIO[5] Config General Purpose Control Reg Bits Field 7:4 3:2 1 GPIO5 DIR 0 GPIO5 EN 7:0 Default Description RESERVED 0000'b Reserved RESERVED 00'b Reserved RW 1 0: Output 1: Input RW 1 0: TRI-STATE 1: Enabled GPCR[7] GPCR[6] GPCR[5] GPCR[4] GPCR[3] GPCR[2] GPCR[1] GPCR[0] R/W 0: LOW 1: HIGH RW 0x00'h 22 Addr (Hex) 0 1 Name Bits Field R/W Default RW 0xC0'h 7:1 DEVICE ID 7-bit address of Deserializer; 0x60h (1100_000X) default 0 DES ID SEL 0: Device ID is from ID[x] 1: Register I2C Device ID overrides ID[x] 7:3 RESERVED I2C Device ID 0x00'h 0 Description Reserved Remote Wake-up Select 1: Enable Generate remote wakeup signal automatically wake-up the Serializer in Standby mode 0: Disable Puts the Serializer (MODE = 0) in Standby mode when Deserializer MODE = 1 2 REM_WAKEUP RW 1 DIGITALRESET0 RW 1: Resets the device to default register values. Does not 0 self clear affect device I2C Bus or Device ID 0 DIGITALRESET1 RW 0 1: Digital Reset, retains all register values self clear Reset RESERVED 7:6 RESERVED 00'b Auto Clock 5 AUTO_CLOCK RW 0 1: Output PCLK or Internal 25 MHz Oscillator clock 0: Only PCLK when valid PCLK present OSS Select 4 OSS_SEL RW 0 Output Sleep State Select 0: Outputs = TRI-STATE, when LOCK = L 1: Outputs = LOW , when LOCK = L 2 SSCG 3:0 SSCG 0000'b 23 Reserved SSCG Select 0000: Normal Operation, SSCG OFF (default) 0001: fmod (kHz) PCLK/2168, fdev ±0.50% 0010: fmod (kHz) PCLK/2168, fdev ±1.00% 0011: fmod (kHz) PCLK/2168, fdev ±1.50% 0100: fmod (kHz) PCLK/2168, fdev ±2.00% 0101: fmod (kHz) PCLK/1300, fdev ±0.50% 0110: fmod (kHz) PCLK/1300, fdev ±1.00% 0111: fmod (kHz) PCLK/1300, fdev ±1.50% 1000: fmod (kHz) PCLK/1300, fdev ±2.00% 1001: fmod (kHz) PCLK/868, fdev ±0.50% 1010: fmod (kHz) PCLK/868, fdev ±1.00% 1011: fmod (kHz) PCLK/868, fdev ±1.50% 1100: fmod (kHz) PCLK/868, fdev ±2.00% 1101: fmod (kHz) PCLK/650, fdev ±0.50% 1110: fmod (kHz) PCLK/650, fdev ±1.00% 1111: fmod (kHz) PCLK/650, fdev ±1.50% www.ti.com DS90UB901Q/DS90UB902Q TABLE 2. DS90UB902Q Control Registers DS90UB901Q/DS90UB902Q Addr (Hex) Name Bits 7 CRC Fault Tolerant Transmission VDDIO Control Field TX CRC CHECKER ENABLE R/W Default RW 1 Back Channel CRC Enable 0: Disable 1: Enable For proper CRC operation, on Serailizer 0x03h b[6] control register must be Enabled. 6 RX CRC GEN ENABLE RW 1 Foward Channel CRC Enable 0: Disable 1: Enable For proper CRC operation, on Serailizer 0x03h b[7] control register must be Enabled. 5 VDDIO CONTROL RW 1 Auto voltage control 0: Disable 1: Enable (auto detect mode) VDDIO Mode 4 VDDIO MODE RW 0 VDDIO voltage set Only used when VDDIOCONTROL = 0 0: 1.8V 1: 3.3V I2C Pass-Through 3 I2C PASSTHROUGH RW 1 I2C Pass-Through Mode 0: Disabled 1: Enabled Auto ACK 2 AUTO ACK RW 0 0: Disable 1: Enable CRC Reset 1 CRC RESET RW 0 1: CRC reset 1 Pixel Clock Edge Select 0: Parallel Interface Data is strobed on the Falling Clock Edge 1: Parallel Interface Data is strobed on the Rising Clock Edge. 3 RRFB 0 RRFB 4 EQ Control 7:0 EQ 5 RESERVED 7:0 RESERVED www.ti.com Description RW RW 24 0x00'h EQ Gain 00'h = ~0.0 dB 01'h = ~4.5 dB 03'h = ~6.5 dB 07'h = ~7.5 dB 0F'h = ~8.0 dB 1F'h = ~11.0 dB 3F'h = ~12.5 dB FF'h = ~14.0 dB 0x00'h Reserved Name Bits RESERVED 7 SCL Prescale 6 Remote NACK Remote NACK 7 8 9 SER ID ID[0] Index ID[1] Index A ID[2] Index B ID[3] Index C D E ID[4] Index ID[5] Index ID[6] Index F ID[7] Index 10 ID[0] Match 11 ID[1] Match 12 ID[2] Match 13 ID[3] Match 6:4 3 Field R/W Default RESERVED SCL_PRESCALE REM_NACK_TIM ER 2:0 NACK_TIMEOUT 7:1 SER DEV ID 0 RESERVED 7:1 ID[0] INDEX 0 RESERVED 7:1 ID[1] INDEX 0 RESERVED 7:1 ID[2] INDEX 0 RESERVED 7:1 ID[3] INDEX 0 RESERVED 7:1 ID[4] INDEX 0 RESERVED 7:1 ID[5] INDEX 0 RESERVED 7:1 ID[6] INDEX 0 RESERVED 7:1 ID[7] INDEX 0 RESERVED 7:1 ID[0] MATCH 0 RESERVED 7:1 ID[1] MATCH 0 RESERVED 7:1 ID[2] MATCH 0 RESERVED 7:1 ID[3] MATCH 0 RESERVED 0 RW RW Description Reserved 000'b Prescales the SCL clock line when reading data byte from a slave device (MODE = 0) 000 : ~100 kHz SCL (default) 001 : ~125 kHz SCL 101 : ~11 kHz SCL 110 : ~33 kHz SCL 111 : ~50 kHz SCL Other values are NOT supported. 1 Remote NACK Timer Enable In slave mode (MODE = 1) if bit is set the I2C core will automatically timeout when no acknowledge condition was detected. 1: Enable 0: Disable RW 111'b RW 0xB0'h Remote NACK Timeout. 000: 2.0 ms 001: 5.2 ms 010: 8.6 ms 011: 11.8 ms 100: 14.4 ms 101: 18.4 ms 110: 21.6 ms 111: 25.0 ms Serializer Device ID = 0x58'h (1011_000X'b) default Reserved RW 0x00'h Target slave Device ID slv_id0 [7:1] Reserved RW 0x00'h RW 0x00'h RW 0x00'h RW 0x00'h RW 0x00'h RW 0x00'h RW 0x00'h RW 0x00'h RW 0x00'h RW 0x00'h RW 0x00'h 25 Target slave Device ID slv_id1 [7:1] Reserved Target slave Device ID slv_id2 [7:1] Reserved Target slave Device ID slv_id3 [7:1] Reserved Target slave Device ID slv_id4 [7:1] Reserved Target slave Device ID slv_id5 [7:1] Reserved Target slave Device ID slv_id6 [7:1] Reserved Target slave Device ID slv_id7 [7:1] Reserved Alias to match Device ID slv_id0 [7:1] Reserved Alias to match Device ID slv_id1 [7:1] Reserved Alias to match Device ID slv_id2 [7:1] Reserved Alias to match Device ID slv_id3 [7:1] Reserved www.ti.com DS90UB901Q/DS90UB902Q Addr (Hex) DS90UB901Q/DS90UB902Q Addr (Hex) Name 14 ID[4] Match 15 ID[5] Match 16 ID[6] Match Bits Field 7:1 ID[4] MATCH 0 RESERVED 7:1 ID[5] MATCH 0 RESERVED 7:1 ID[6] MATCH 0 RESERVED 7:1 ID[7] MATCH R/W Default RW 0x00'h RW 0x00'h RW 0x00'h RW 0x00'h Description Alias to match Device ID slv_id4 [7:1] Reserved Alias to match Device ID slv_id5 [7:1] Reserved Alias to match Device ID slv_id6 [7:1] Reserved Alias to match Device ID slv_id [7:1] 17 ID[7] Match 0 RESERVED 18 RESERVED 7:0 RESERVED 0x00'h Reserved 19 RESERVED 7:0 RESERVED 0x01'h Reserved 1A CRC Errors 7:0 CRC ERROR B0 R 0x00'h Number of CRC errors 8 LSBs 1B CRC Errors 7:0 CRC ERROR B1 R 0x00'h Number of CRC errors 8 MSBs RESERVED 7:3 RESERVED 0x00'h Reserved CRC Check 2 SER ERROR Signal Detect Status LOCK Pin Status 1C 1D 1E 1F 20 www.ti.com GPIO[0] Config GPIO[1] Config GPIO[2] Config GPIO[3] Config Reserved R 0 CRC error during communication with Serializer on Forward Channel 1 R 0 0: Active signal not detected 1: Active signal detected 0 R 0 0: CDR/PLL Unlocked 1: CDR/PLL Locked 7:3 RESERVED 2 GPIO0 SET 1 GPIO0 DIR 0 GPIO0 EN 00010'b RW RW Reserved 1 1: Configured as GPIO 0: Configured as ROUT data (OSS_SEL controlled) 1 0: Output 1: Input 1 0: TRI-STATE 1: Enabled 7:3 RESERVED 0x00'h 2 GPIO1 SET RW 1 1: Configured as GPIO 0: Configured as ROUT data (OSS_SEL controlled) 1 GPIO1 DIR RW 1 0: Output 1: Input 0 GPIO1 EN RW 1 0: TRI-STATE 1: Enabled 0x00'h Reserved 7:3 RESERVED 2 GPIO2 SET RW 0 1: Configured as GPIO 0: Configured as ROUT0 data (OSS_SEL controlled) 1 GPIO2 DIR RW 0 0: Output 1: Input 0 GPIO2 EN RW 1 0: TRI-STATE 1: Enabled 0x00'h Reserved 7:3 RESERVED 2 GPIO3 SET RW 0 1: Configured as GPIO 0: Configured as ROUT1 data (OSS_SEL controlled) 1 GPIO3 DIR RW 0 0: Output 1: Input 0 GPIO3 EN RW 1 0: TRI-STATE 1: Enabled 26 Reserved 21 22 Name GPIO[4] Config GPIO[5] Config Bits Field R/W Default 0x00'h Description 7:3 RESERVED 2 GPIO4 SET RW 0 1: Configured as GPIO 0: Configured as ROUT2 data (OSS_SEL controlled) 1 GPIO4 DIR RW 0 0: Output 1: Input 0 GPIO4 EN RW 1 0: TRI-STATE 1: Enabled 0x00'h Reserved 7:3 RESERVED Reserved 2 GPIO5 SET RW 0 1: Configured as GPIO 0: Configured as ROUT3 data (OSS_SEL controlled) 1 GPIO5 DIR RW 0 0: Output 1: Input 0 GPIO5 EN RW 1 0: TRI-STATE 1: Enabled 23 General Purpose Control Reg 7:0 GPCR[7] GPCR[6] GPCR[5] GPCR[4] GPCR[3] GPCR[2] GPCR[1] GPCR[0] 24 BIST 0 BIST_EN 25 BIST_ERR 7:0 BIST_ERR 26 Remote Wake Enable 7:6 REM_WAKEUP_ EN RW 5:0 RESERVED RW 0 7:6 BCC RW 00'b 5:0 RESERVED 0 Reserved 7:5 RESERVED 0 Reserved 1 1: Disabled (Default) 0: Enabled 0 Reserved 27 3F BCC CMLOUT Config 4 3:0 CMLOUT P/N Enable 0: LOW 1: HIGH RW 0x00'h RW 0 R 0x00'h 00'b RW RESERVED 27 BIST Enable 0: Normal operation 1: Bist Enable Bist Error Counter 11: Enable remote wake mode 00: Normal operation mode Other values are NOT supported. Reserved 11: Normal operation mode www.ti.com DS90UB901Q/DS90UB902Q Addr (Hex) DS90UB901Q/DS90UB902Q The bidirectional control channel of the DS90UB901Q/902Q provides bidirectional communication between the image sensor and Electronic Control Unit (ECU) over the same differential pair used for video data interface. This interface offers advantages over other chipsets by eliminating the need for additional wires for programming and control. The bidirectional control channel bus is controlled via an I2C port. The bidirectional control channel offers asymmetrical communication and is not dependent on video blanking intervals. Functional Description The DS90UB901Q/902Q FPD-Link III chipset is intended for camera applications. The Serializer/ Deserializer chipset operates from a 10 MHz to 43 MHz pixel clock frequency. The DS90UB901Q transforms a 16-bit wide parallel LVCMOS data bus along with a bidirectional control bus into a single highspeed differential pair. The high-speed serial bit stream contains an embedded clock and DC-balance information which enhances signal quality to support AC coupling. The DS90UB902Q receives the single serial data stream and converts it back into a 16-bit wide parallel data bus together with the bidirectional control channel data bus. SERIAL FRAME FORMAT The DS90UB901Q/902Q chipset will transmit and receive a pixel of data in the following format: 30113561 FIGURE 21. Serial Bitstream for 28-bit Symbol The High Speed Forward Channel is a 28-bit symbol composed of 16 bits of data containing camera data & control information transmitted from Serializer to Deserializer. CLK1 and CLK0 represent the embedded clock in the serial stream. CLK1 is always HIGH and CLK0 is always LOW. This data payload is optimized for signal transmission over an AC coupled link. Data is randomized, balanced and scrambled. The data payload may be checked using a 4-bit CRC function. The CRC monitors the link integrity of the serialized data and reports when an error condition is detected. The bidirectional control channel data is transferred along with the high-speed forward data over the same serial link. This architecture provides a full duplex low speed back channel across the serial link together with a high speed forward channel without the dependence of the video blanking phase. the clock (SCL) and data (SDA) signals. Pull-up resistors or current sources are required on the SCL and SDA busses to pull them high when they are not being driven low. A logic zero is transmitted by driving the output low. A logic high is transmitted by releasing the output and allowing it to be pulled-up externally. The appropriate pull-up resistor values will depend upon the total bus capacitance and operating speed. The DS90UB901Q/902Q I2C bus data rate supports up to 100 kbps according to I2C specification. To start any data transfer, the DS90UB901Q/902Q must be configured in the proper I2C mode. Each device can function as an I2C slave proxy or master proxy depending on the mode determined by MODE pin. The Ser/Des interface acts as a virtual bridge between Master controller (MCU) and the remote device. When the MODE pin is set to High, the device is treated as a slave proxy; acts as a slave on behalf of the remote slave. When addressing a remote peripheral or Serializer/Deserializer (not wired directly to the MCU), the slave proxy will forward any byte transactions sent by the Master controller to the target device. When MODE pin is set to Low, the device will function as a master proxy device; acts as a master on behalf of the I2C master controller. Note that the devices must have complementary settings for the MODE configuration. For example, if the Serializer MODE pin is set to High then the Deserializer MODE pin must be set to Low and vice-versa. DESCRIPTION OF BIDIRECTIONAL CONTROL BUS AND I2C MODES The I2C compatible interface allows programming of the DS90UB901Q, DS90UB902Q, or an external remote device (such as a camera) through the bidirectional control channel. Register programming transactions to/from the DS90UB901Q/902Q chipset are employed through the clock (SCL) and data (SDA) lines. These two signals have opendrain I/Os and both lines must be pulled-up to VDDIO by external resistor. Figure 4 shows the timing relationships of 30113560 FIGURE 22. Write Byte www.ti.com 28 FIGURE 23. Read Byte 30113541 FIGURE 24. Basic Operation 30113542 FIGURE 25. START and STOP Conditions accesses, the “Response Delay” shown is on the order of 12 µs (typical). See Application Note AN-2173 / SNLA131 for more details. SLAVE CLOCK STRETCHING In order to communicate and synchronize with remote devices on the I2C bus through the bidirectional control channel, slave clock stretching must be supported by the I2C master controller/MCU. The chipset utilizes bus clock stretching (holding the SCL line low) during data transmission; where the I2C slave pulls the SCL line low prior to the 9th clock of every I2C data transfer (before the ACK signal). The slave device will not control the clock and only stretches it until the remote peripheral has responded. Any remote access involves the clock stretching period following the transmitted byte, prior to completion of the acknowledge bit. Since each byte transferred to the I2C slave must be acknowledged separately, the clock stretching will be done for each byte sent by the host controller. For remote ID[X] ADDRESS DECODER The ID[x] pin is used to decode and set the physical slave address of the Serializer/Deserializer (I2C only) to allow up to six devices on the bus using only a single pin. The pin sets one of six possible addresses for each Serializer/Deserializer device. The pin must be pulled to VDD (1.8V, NOT VDDIO)) with a 10 kΩ resistor and a pull down resistor (RID) of the recommended value to set the physical device address. The recommended maximum resistor tolerance is 0.1% worst case (0.2% total tolerance). 29 www.ti.com DS90UB901Q/DS90UB902Q 30113510 DS90UB901Q/DS90UB902Q 30113543 FIGURE 26. Bidirectional Control Bus Connection CAMERA MODE OPERATION In Camera mode, I2C transactions originate from the Master controller at the Deserializer side (Figure 27). The I2C slave core in the Deserializer will detect if a transaction is intended for the Serializer or a slave at the Serializer. Commands are sent over the bidirectional control channel to initiate the transactions. The Serializer will receive the command and generate an I2C transaction on its local I2C bus. At the same time, the Serializer will capture the response on the I2C bus and return the response on the forward channel link. The Deserializer parses the response and passes the appropriate response to the Deserializer I2C bus. To configure the devices for camera mode operation, set the Serializer MODE pin to Low and the Deserializer MODE pin to High. Before initiating any I2C commands, the Deserializer needs to be programmed with the target slave device addresses and Serializer device address. SER_DEV_ID Register 0x07h sets the Serializer device address and SLAVE_x_MATCH/SLAVE_x_INDEX registers 0x08h~0x17h set the remote target slave addresses. In slave mode the address register is compared with the address byte sent by the I2C master. If the addresses are equal to any of registers values, the I2C slave will acknowledge and hold the bus to propagate the transaction to the target device otherwise it returns no acknowledge. TABLE 3. ID[x] Resistor Value – DS90UB901Q ID[x] Resistor Value - DS90UB901Q Ser Resistor RID Ω (±0.1%) 0 GND Address 7'b (Note 11) Address 8'b 0 appended (WRITE) 7b' 101 1000 (h'58) 8b' 1011 0000 (h'B0) 2.0k 7b' 101 1001 (h'59) 8b' 1011 0010 (h'B2) 4.7k 7b' 101 1010 (h'5A) 8b' 1011 0100 (h'B4) 8.2k 7b' 101 1011 (h'5B) 8b' 1011 0110 (h'B6) 12.1k 7b' 101 1100 (h'5C) 8b' 1011 1000 (h'B8) 39.0k 7b' 101 1110 (h'5E) 8b' 1011 1100 (h'BC) TABLE 4. ID[x] Resistor Value – DS90UB902Q ID[x] Resistor Value - DS90UB902Q Des Resistor RID Ω (±0.1%) Address 7'b (Note 11) Address 8'b 0 appended (WRITE) 0 GND 7b' 110 0000 (h'60) 8b' 1100 0000 (h'C0) 2.0k 7b' 110 0001 (h'61) 8b' 1100 0010 (h'C2) 4.7k 7b' 110 0010 (h'62) 8b' 1100 0100 (h'C4) 8.2k 7b' 110 0011 (h'63) 8b' 1101 0110 (h'C6) 12.1k 7b' 110 0100 (h'64) 8b' 1101 1000 (h'C8) 39.0k 7b' 110 0110 (h'66) 8b' 1100 1100 (h'CC) 30113540 FIGURE 27. Typical Camera System Diagram www.ti.com 30 PROGRAMMABLE CONTROLLER An integrated I2C slave controller is embedded in each of the DS90UB901Q Serializer and DS90UB902Q Deserializer. It must be used to access and program the extra features embedded within the configuration registers. Refer to Table 1 and Table 2 for details of control registers. MULTIPLE DEVICE ADDRESSING Some applications require multiple camera devices with the same fixed address to be accessed on the same I2C bus. The DS90UB901/902 provides slave ID matching/aliasing to generate different target slave addresses when connecting more than two identical devices together on the same bus. This allows the slave devices to be independently addressed. Each device connected to the bus is addressable through a unique ID by programming of the SLAVE_ID_MATCH register on Deserializer. This will remap the SLAVE_ID_MATCH address to the target SLAVE_ID_INDEX address; up to 8 ID indexes are supported. The ECU Controller must keep track of the list of I2C peripherals in order to properly address the target device. In a camera application, the microcontroller is located on the Deserializer side. In this case, the microcontroller programs the slave address matching registers and handles all data transfers to and from all slave I2C devices. This is useful in the event where camera modules are removed or replaced. For example in the configuration shown in Figure 28: • ECU is the I2C master and has an I2C master interface • The I2C interfaces in DES A and DES B are both slave interfaces • The I2C protocol is bridged from DES A to SER A and from DES B to SER B • The I2C interfaces in SER A and SER B are both master interfaces If master controller transmits I2C slave 0xA0, the DES A address 0xC0 will forward the transaction to remote Camera A. If the controller transmits slave address 0xA4, the DES B 0xC2 will recognize that 0xA4 is mapped to 0xA0 and will be transmitted to the remote Camera B. If controller sends command to address 0xA6, the DES B 0xC2 will forward transaction to slave device 0xA2. The Slave ID index/match is supported only in the camera mode (SER: MODE pin = L; DES: MODE pin = H). For Multiple device addressing in display mode (SER: MODE pin = H; DES: MODE pin = L), use the I2C pass through function. CRC (CYCLIC REDUNDANCY CHECK) DETECTION A 4-bit CRC per symbol is reserved for checking the link integrity during transmission. The reporting status pin (PASS) is provided on the Deserializer side, which flags any mismatch of data transmitted to and from the remote device. The Deserializer's PLL must first be locked (LOCK pin HIGH) to ensure the PASS status is valid. This error detection handling generates an interrupt signal onto the PASS output pin; notifying the host controller as soon as any errors are identified. When an error occurs, the PASS asserts LOW. CRC registers (CRC ERROR B0/B1) are also available for managing the data error count. The DS90UB901Q/902Q chipset provides several mechanisms (operations) for ensuring data integrity in long distance transmission and reception. The data error detection function offers user flexibility and usability of performing bit-by-bit and 31 www.ti.com DS90UB901Q/DS90UB902Q data transmission error checking. The error detection operating modes support data validation of the following signals: • Bidirectional Channel Control • Control VSYNC and HSYNC signals across serial link • Parallel video/pixel data across serial link DISPLAY MODE OPERATION In Display mode, I2C transactions originate from the controller attached to the Serializer. The I2C slave core in the Serializer will detect if a transaction targets (local) registers within the Serialier or the (remote) registers within the Deserializer or a remote slave connected to the I2C master interface of the Deserializer. Commands are sent over the forward channel link to initiate the transactions. The Deserializer will receive the command and generate an I2C transaction on its local I2C bus. At the same time, the Deserializer will capture the response on the I2C bus and return the response as a command on the bidirectional control channel. The Serializer parses the response and passes the appropriate response to the Serializer I2C bus. The physical device ID of the I2C slave in the Serializer is determined by the analog voltage on the ID[x] input. It can be reprogrammed by using the DEVICE_ID register and setting the bit . The device ID of the logical I2C slave in the Deserializer is determined by programming the DES ID in the Serializer. The state of the ID[x] input on the Deserializer is used to set the device ID. The I2C transactions between Ser/Des will be bridged between the host controller to the remote slave. To configure the devices for display mode operation, set the Serializer MODE pin to High and the Deserializer MODE pin to Low. Before initiating any I2C commands, the Serializer needs to be programmed with the target slave device address and Serializer device address. DES_DEV_ID Register 0x06h sets the Deserializer device address and SLAVE_DEV_ID register 0x7h sets the remote target slave address. If the I2C slave address matches any of registers values, the I2C slave will hold the transaction allowing read or write to target device. Note: In Display mode operation, registers 0x08h~0x17h on Deserializer must be reset to 0x00. DS90UB901Q/DS90UB902Q 30113533 FIGURE 28. Multiple Device Addressing communication to only specific devices on the remote bus. The feature is effective for both Camera mode and Display mode. For example in the configuration shown in Figure 29: If master controller transmits I2C transaction for address 0xA0, the SER A with I2C pass through enabled will transfer I2C commands to remote Camera A. The SER B with I2C pass through disabled, any I2C commands will be bypassed on the I2C bus to Camera B. I2C PASS THROUGH I2C pass-through provides an alternative means to independently address slave devices. The mode enables or disables I2C bidirectional control channel communication to the remote I2C bus. This option is used to determine whether or not an I2C instruction is to be transferred over to the remote I2C device. When enabled, the I2C bus traffic will continue to pass through and will be received by I2C devices downstream. If disabled, I2C commands will be blocked to the remote I2C device. The pass through function also provides access and www.ti.com 32 DS90UB901Q/DS90UB902Q 30113504 FIGURE 29. I2C Pass Through tional control channel, there will be a time variation of the GPIO signals arriving at the different target devices (between the parallel links). The maximum latency delta (t1) of the GPIO data transmitted across multiple links is 25 us. Note: The user must verify that the timing variations between the different links are within their system and timing specifications. For example in the configuration shown in (Figure 30): The maximum time (t1) between the rising edge of GPIO (i.e. sync signal) arriving at Camera A and Camera B is 25 us. SYNCHRONIZING MULTIPLE CAMERAS For applications requiring multiple cameras for frame-synchronization, it is recommended to utilize the General Purpose Input/Output (GPIO) pins to transmit control signals to synchronize multiple cameras together. To synchronize the cameras properly, the system controller needs to provide a field sync output (such as a vertical or frame sync signal) and the cameras must be set to accept an auxiliary sync input. The vertical synchronize signal corresponds to the start and end of a frame and the start and end of a field. Note this form of synchronization timing relationship has a non-deterministic latency. After the control data is reconstructed from the birec- 33 www.ti.com DS90UB901Q/DS90UB902Q 30113553 FIGURE 30. Synchronizing Multiple Cameras 30113554 FIGURE 31. GPIO Delta Latency GENERAL PURPOSE I/O (GPIO) The DS90UB901Q/902Q has up to 6 GPIO (2 dedicated and 4 programmable). GPIO[0] and GPIO[1] are always available and GPIO[2:5] are available depending on the parallel data bus size. DIN/ROUT[0:3] can be programmed into GPIOs (GPIO[2:5]) when the parallel data bus is less than 12 bits wide (10-bit data + HS,VS). Each GPIO can be configured as either an input or output port. The GPIO maximum switching rate is up to 66 kHz when configured for communication between Deserializer GPI to Serializer GPO. Whereas data flow configured for communication between Serializer GPI to Deserializer GPO is limited by the maximum data rate of the PCLK. www.ti.com AT-SPEED BIST (BISTEN, PASS) An optional AT SPEED Built in Self Test (BIST) feature supports at speed testing of the high-speed serial and the bidirectional control channel link. Control pins at the Deserializer are used to enable the BIST test mode and allow the system to initiate the test and set the duration. A HIGH on PASS pin indicates that all payloads received during the test were error free during the BIST duration test. A LOW on this pin at the conclusion of the test indicates that one or more payloads were detected with errors. The BIST duration is defined by the width of BISTEN. BIST starts when Deserializer LOCK goes HIGH and BISTEN is set HIGH. BIST ends when BISTEN goes LOW. Any errors detected after the BIST Duration are not included in PASS logic. 34 The following diagram shows how to perform system AT SPEED BIST: 30113545 FIGURE 32. AT-SPEED BIST System Flow Diagram Deserializer will communicate through the bidirectional control channel to configure Serializer into BIST mode. Once the BIST mode is set, the Serializer will initiate BIST transmission to the Deserializer. Wait 10 ms for Deserializer to acquire lock and then monitor the LOCK pin transition from LOW to HIGH. At this point, AT SPEED BIST is operational and the BIST process has begun. The Serializer will start transfer of an internally generated PRBS data pattern through the high speed serial link. This pattern traverses across the interconnecting link to the Deserializer. Check the status of the PASS pin; a HIGH indicates a pass, a LOW indicates a fail. A fail will stay LOW for ½ a clock cycle. If two or more bits in the serial frame fail, the PASS pin will toggle ½ clock cycle HIGH and ½ clock cycle low. The user can use the PASS pin to count the number of fails on the high speed link. In addition, there is a defined SER and DES register that will keep track of the accumulated error count. The Serializer 901 GPIO[0] pin will be assigned as a PASS flag error indicator for the bidirectional control channel link. Step 1: Place the Deserializer in BIST Mode. Serializer and Deserializer power supply must be supplied. Enable the AT SPEED BIST mode on the Deserializer by setting the BISTEN pin High. The 902 GPIO[1:0] pins are used to select the PCLK frequency of the on-chip oscillator for the BIST test on high speed data path. TABLE 5. BIST Oscillator Frequency Select Des GPIO [1:0] Oscillator Source min typ max (MHz) (MHz) (MHz ) 00 External PCLK 01 Internal 10 50 43 10 Internal 25 11 Internal 12.5 The Deserializer GPIO[1:0] set to 00 will bypass the on-chip oscillator and an external oscillator to Serializer PCLK input is required. This allows the user to operate BIST under different frequencies other than the predefined ranges. Step 2: Enable AT SPEED BIST by placing the Serializer into BIST mode. 35 www.ti.com DS90UB901Q/DS90UB902Q Note: AT-SPEED BIST is only available in the Camera mode and not the Display mode DS90UB901Q/DS90UB902Q 30113564 FIGURE 33. BIST Timing Diagram Step 3: Stop at SPEED BIST by turning off BIST mode in the Deserializer to determine Pass/Fail. To end BIST, the system must pull BISTEN pin of the Deserializer LOW. The BIST duration is fully defined by the BIS- TEN width and Deserializer LOCK is HIGH; thus the Bit Error Rate is determined by how long the system holds BISTEN HIGH. 30113505 FIGURE 34. BIST BER Calculation For instance, if BISTEN is held HIGH for 1 second and the PCLK is running at 43 MHz with 16 bpp, then the Bit Error Rate is no better than 1.46E-9. Step 4: Place system in Normal Operating Mode by disabling BIST at the Serializer. Once Step 3 is complete, AT SPEED BIST is over and the Deserializer is out of BIST mode. To fully return to Normal mode, apply Normal input data into the Serializer. Any PASS result will remain unless it is changed by a new BIST session or cleared by asserting and releasing PDB. The default state of PASS after a PDB toggle is HIGH. It is important to note that AT SPEED BIST will only determine if there is an issue on the link that is not related to the clock and data recovery of the link (whose status is flagged with LOCK pin). www.ti.com LVCMOS VDDIO OPTION 1.8V or 3.3V SER Inputs and DES Outputs are user seletable to provide compatibility with 1.8V and 3.3V system interfaces. REMOTE WAKE UP (Camera Mode) After initial power up, the Serializer is in a low-power Standby mode. The Deserializer (controlled by ECU/MCU) 'Remote Wake-up' register allows the Deserializer side to generate a signal across the link to remotely wake-up the Serializer. Once the Serializer detects the wake-up signal Serializer switches from Standby mode to active mode. In active mode, the Serializer locks onto PCLK input (if present), otherwise the on-chip oscillator is used as the input clock source. Note the MCU controller should monitor the Deserializer LOCK pin and confirm LOCK = H before performing any I2C communication across the link. For Remote Wake-up to function properly: 36 ization is controlled via register setting. Note this function can be observed at the CMLOUTP/N test port enabled via the control registers. The chipset needs to be configured in Camera mode: Serializer MODE = 0 and Deserializer MODE = 1 • Serializer expects remote wake-up by default at power on. • Configure the control channel driver of the Deserializer to be in remote wake-up mode by setting Deserializer Register 0x26h = 0xC0h. • Perform remote wake-up on Serializer by setting Deserializer Register 0x01 b[2] = 1 • Return the control channel driver of the Deserializer to the normal operation mode by setting Deserializer Register 0x26h = 0x00h • Configure the control channel driver of the Deserializer to be in normal operation mode by setting Deserializer Register 0x27h = 0xC0h. Serializer can also be put into standby mode by programming the Deserializer remote wake-up control register 0x01 b[2] REM_WAKEUP to 0. EMI REDUCTION Des - Receiver Staggered Output The Receiver staggered outputs allows for outputs to switch in a random distribution of transitions within a defined window. Outputs transitions are distributed randomly. This minimizes the number of outputs switching simultaneously and helps to reduce supply noise. In addition it spreads the noise spectrum out reducing overall EMI. Des Spread Spectrum Clocking The DS90UB902Q parallel data and clock outputs have programmable SSCG ranges from 9 kHz–66 kHz and ±0.5%– ±2% from 20 MHz to 43 MHz. The modulation rate and modulation frequency variation of output spread is controlled through the SSC control registers. POWERDOWN The SER has a PDB input pin to ENABLE or Powerdown the device. The modes can be controlled by the host and is used to disable the Link to save power when the remote device is not operational. An auto mode is also available. In this mode, the PDB pin is tied High and the SER switches over to an internal oscillator when the PCLK stops or not present. When a PCLK starts again, the SER will then lock to the valid input PCLK and transmits the data to the DES. In powerdown mode, the high-speed driver outputs are static (High). The DES has a PDB input pin to ENABLE or Powerdown the device. This pin can be controlled by the system and is used to disable the DES to save power. An auto mode is also available. In this mode, the PDB pin is tied High and the DES will enter powerdown when the serial stream stops. When the serial stream starts up again, the DES will lock to the input stream and assert the LOCK pin and output valid data. In powerdown mode, the Data and PCLK outputs are set by the OSS_SEL control register. PIXEL CLOCK EDGE SELECT (TRFB/RRFB) The TRFB/RRFB selects which edge of the Pixel Clock is used. For the SER, this register determines the edge that the data is latched on. If TRFB register is 1, data is latched on the Rising edge of the PCLK. If TRFB register is 0, data is latched on the Falling edge of the PCLK. For the DES, this register determines the edge that the data is strobed on. If RRFB register is 1, data is strobed on the Rising edge of the PCLK. If RRFB register is 0, data is strobed on the Falling edge of the PCLK. 30113551 POWER UP REQUIREMENTS AND PDB PIN It is required to delay and release the PDB input signal after VDD (VDDn and VDDIO) power supplies have settled to the recommended operating voltages. A external RC network can be connected to the PDB pin to ensure PDB arrives after all the VDD have stabilized. FIGURE 35. Programmable PCLK Strobe Select SIGNAL QUALITY ENHANCERS Des - Receiver Input Equalization (EQ) The receiver inputs provided input equalization filter in order to compensate for loss from the media. The level of equal- 37 www.ti.com DS90UB901Q/DS90UB902Q • DS90UB901Q/DS90UB902Q nal AC coupling capacitors must be placed in series in the FPD-Link III signal path as illustrated in Figure 36. Applications Information AC COUPLING The SER/DES supports only AC-coupled interconnects through an integrated DC balanced decoding scheme. Exter- 30113538 FIGURE 36. AC-Coupled Connection For high-speed FPD-Link III transmissions, the smallest available package should be used for the AC coupling capacitor. This will help minimize degradation of signal quality due to package parasitics. The I/O’s require a 100 nF AC coupling capacitors to the line. TYPICAL APPLICATION CONNECTION Figure 37 shows a typical connection of the DS90UB901Q Serializer. 30113555 FIGURE 37. DS90UB901Q Typical Connection Diagram — Pin Control www.ti.com 38 DS90UB901Q/DS90UB902Q Figure 38 shows a typical connection of the DS90UB902Q Deserializer. 30113556 FIGURE 38. DS90UB902Q Typical Connection Diagram — Pin Control 39 www.ti.com DS90UB901Q/DS90UB902Q the electrical environment (e.g. power stability, ground noise, input clock jitter, PCLK frequency, etc.) and the application environment. The resulting signal quality at the receiving end of the transmission media may be assessed by monitoring the differential eye opening of the CMLOUT P/N output. A differential probe should be used to measure across the termination resistor at the CMLOUT P/N pins. For obtaining optimal performance, we recommend: • Use Shielded Twisted Pair (STP) cable • 100Ω differential impedance and 24 AWG (or lower AWG) cable • Low skew, impedance matched • Ground and/or terminate unused conductors Figure 39 shows the Typical Performance Characteristics demonstrating various lengths and data rates using Rosenberger HSD and Leoni DACAR 538 Cable. TRANSMISSION MEDIA The Ser/Des chipset is intended to be used over a wide variety of balanced cables depending on distance and signal quality requirements. The Ser/Des employ internal termination providing a clean signaling environment. The interconnect for FPD-Link III interface should present a differential impedance of 100 Ohms. Use of cables and connectors that have matched differential impedance will minimize impedance discontinuities. Shielded or un-shielded cables may be used depending upon the noise environment and application requirements. The chipset's optimum cable drive performance is achieved at 43 MHz at 10 meters length. The maximum signaling rate increases as the cable length decreases. Therefore, the chipset supports 50 MHz at shorter distances. Other cable parameters that may limit the cable's performance boundaries are: cable attenuation, near-end crosstalk and pair-to-pair skew. The maximum length of cable that can be used is dependant on the quality of the cable (gauge, impedance), connector, board (discontinuities, power plane), 30113557 *Note: Equalization is enabled for cable lengths greater than 7 meters FIGURE 39. Rosenberger HSD & Leoni DACAR 538 Cable Performance bypass capacitors connected to the plane with via on both ends of the capacitor. Connecting power or ground pins to an external bypass capacitor will increase the inductance of the path. A small body size X7R chip capacitor, such as 0603, is recommended for external bypass. Its small body size reduces the parasitic inductance of the capacitor. The user must pay attention to the resonance frequency of these external bypass capacitors, usually in the range of 20-30 MHz. To provide effective bypassing, multiple capacitors are often used to achieve low impedance between the supply rails over the frequency of interest. At high frequency, it is also a common practice to use two vias from power and ground pins to the planes, reducing the impedance at high frequency. Some devices provide separate power for different portions of the circuit. This is done to isolate switching noise effects between different sections of the circuit. Separate planes on the PCB are typically not required. Pin Description tables typically provide guidance on which circuit blocks are connected to which power pin pairs. In some cases, an external filter many be used to provide clean power to sensitive circuits such as PLLs. Use at least a four layer board with a power and ground plane. Locate LVCMOS signals away from the differential lines to PCB LAYOUT AND POWER SYSTEM CONSIDERATIONS Circuit board layout and stack-up for the Ser/Des devices should be designed to provide low-noise power feed to the device. Good layout practice will also separate high frequency or high-level inputs and outputs to minimize unwanted stray noise pickup, feedback and interference. Power system performance may be greatly improved by using thin dielectrics (2 to 4 mils) for power / ground sandwiches. This arrangement provides plane capacitance for the PCB power system with low-inductance parasitics, which has proven especially effective at high frequencies, and makes the value and placement of external bypass capacitors less critical. External bypass capacitors should include both RF ceramic and tantalum electrolytic types. RF capacitors may use values in the range of 0.01 uF to 0.1 uF. Tantalum capacitors may be in the 2.2 uF to 10 uF range. Voltage rating of the tantalum capacitors should be at least 5X the power supply voltage being used. Surface mount capacitors are recommended due to their smaller parasitics. When using multiple capacitors per supply pin, locate the smaller value closer to the pin. A large bulk capacitor is recommend at the point of power entry. This is typically in the 50uF to 100uF range and will smooth low frequency switching noise. It is recommended to connect power and ground pins directly to the power and ground planes with www.ti.com 40 Use the S/2S/3S rule in spacings – S = space between the pair – 2S = space between pairs – 3S = space to LVCMOS signal • Minimize the number of Vias • Use differential connectors when operating above 500Mbps line speed • Maintain balance of the traces • Minimize skew within the pair Additional general guidance can be found in the LVDS Owner’s Manual - available in PDF format from the Texas Instruments web site at: www.ti.com/lvds INTERCONNECT GUIDELINES See Application Notes AN-1108 / SNLA008 and AN-905 / SNLA035 for full details. • Use 100Ω coupled differential pairs 41 www.ti.com DS90UB901Q/DS90UB902Q • prevent coupling from the LVCMOS lines to the differential lines. Closely-coupled differential lines of 100 Ohms are typically recommended for differential interconnect. The closely coupled lines help to ensure that coupled noise will appear as common-mode and thus is rejected by the receivers. The tightly coupled lines will also radiate less. Information on the LLP style package is provided in Application Note: AN-1187 / SNOA401Q. DS90UB901Q/DS90UB902Q Revision History 04/17/2012 • • • • • • • • • • • • • Added CMLOUT P/N to Deserializer Pin Descriptions Added CMLOUT P/N to Deserializer Pin Diagram Added ESD CDM and ESD MM values Added 3.3V I/O VOH conditions: IOH = -4 mA Corrected 3.3V I/O VOL conditions: IOL = +4 mA Changed NSID DS90UB901/902QSQX to qty 2500 Added “Only used when VDDIOCONTROL = 0” note for Deserializer Register 0x03 bit[4] description Added Register 0x27 BCC in Deserializer Register table Added Register 0x3F CML Output in Deserializer Register table Updated SLAVE CLOCK STRETCHING in Functional Description section Updated REMOTE WAKE UP (Camera Mode) procedure in Functional Description section Updated Des - Receiver Input Equalization (EQ) in Functional Description section Updated TRANSMISSION MEDIA in Applications Information section www.ti.com 42 DS90UB901Q/DS90UB902Q Physical Dimensions inches (millimeters) unless otherwise noted DS90UB901Q Serializer Package Number SQA32A DS90UB902Q Deserializer Package Number SQA40A 43 www.ti.com DS90UB901Q/DS90UB902Q 10 - 43MHz 14 Bit Color FPD-Link III Serializer and Deserializer with Bidirectional Control Channel Notes www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated