ATMEL ATR1841 Front monitor diode for blu-ray/hd-dvd/dvd/cd with twi Datasheet

Features
•
•
•
•
•
•
•
•
•
•
405 nm, 650 nm and 780 nm Wavelengths Supported
Blu-ray/HD-DVD x5, CD-R/RW x52, DVD-R/RW x16
Adjustment of Mode and Gain by Setting Internal Register via Two-wire Interface (TWI)
200 MHz Channel Bandwidth
Paraphase Outputs
Internal Reference Voltage Generation
Fast Settling Time
Low Offset Voltage
Power-down Mode
Pb-free Optical 12-pin Package
Applications
•
•
•
•
•
Blu-ray/HD-DVD
DVD+RW with CD-RW Capability
DVD-RW with CD-RW Capability
DVD-RAM with CD-RW Capability
Recordable Optical Data Storage Devices
1. Description
The ATR1841 is a front monitor diode (FMD) which controls the laser power of the
optical pickup for Blu-ray/HD-DVD, DVD and CD drives in one IC.
With the Two-wire Interface (TWI) it is possible to fit the laser power for
Blu-ray/HD-DVD, DVD and CD. Two bits are used to set the mode/gain level and 6
additional bits are used for gain trimming, within ±6 dB. Entering sleep mode is also
controlled via the TWI.
Front Monitor
Diode for
Blu-ray/HD-DVD/
DVD/CD with
TWI
ATR1841
Summary
Preliminary
The integrated PIN diode and the high speed amplifier with low output impedance
ensures stable driver performance.
All output channels are set to tri-state during sleep mode.
Due to its small package size the ATR1841 is especially suited for applications with
low height requirements like SLIM and Ultra-SLIM drives.
NOTE: This is a summary document.
The complete document is currently not
available. For more information, please
contact your local Atmel sales office.
9103AS–DVD–08/07
Figure 1-1.
Block Diagram
SDA
SCL
Gain Select (H/M/L)
Gain Adjust (±6 dB)
RF+
RFInternal
Vref
VCC
GND
2
ADS
ATR1841 [Preliminary]
9103AS–DVD–08/07
ATR1841 [Preliminary]
2. Pin Configuration
Figure 2-1.
Table 2-1.
Pinning QFN12L
NC
NC
10
11
GND
1
8
GND
RF-
2
7
ADS
RF+
3
6
SCL
VCC
4
5
SDA
9
12
NC
NC
Pin Description
Pin
Symbol
Type
Function
1
GND
Supply
Ground
2
RF-
Analog
Negative output
3
RF+
Analog
Positive output
4
VCC
Supply
Power supply
5
SDA
Digital
TWI serial data
6
SCL
Digital
TWI serial clock
7
ADS
Analog
TWI slave address select
8
GND
Supply
Ground
9
NC
Not connected
10
NC
Not connected
11
NC
Not connected
12
NC
Not connected
3
9103AS–DVD–08/07
3. Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Parameters
Symbol
Value
Unit
Supply voltage
VCC
–0.5 to +6.0
V
Input voltage at any input
Vin
–0.5 to VCC – 0.5
V
Storage temperature
Tstg
–40 to +100
°C
Soldering temperature QFN_Open package
Tsol
260
°C
Symbol
Value
Unit
Supply voltage
VCC
4.5 to 5.5
V
Operating temperature range
Tamb
–10 to +80
°C
4. Recommended Operating Conditions
Parameters
5. Electrical Characteristics: General
VCC = 5V, Tamb = 25°C, λ = 405 nm/780 nm/650 nm
Output load: Rload = 10 kΩ, Cload = 20 pF
No.
1
Parameters
Test Conditions
Pin
Symbol
Min.
Typ.
Max.
Unit
Type*
28
30
mA
A
0.5
mA
A
DC Specifications, Power Supply
1.1
Supply current
ICC
1.2
Supply current
(standby mode)
ICC
1.3
VREF_INT
1.4
TCVREF_INT
1.5
Maximum output voltage
Vout
1.6
Minimum output voltage
Vout
1.7
Power supply rejection
ratio
Low-frequency (10 kHz),
inclusive application/
flexboard
PSRR
1.8
Power supply rejection
ratio
High-frequency
(100 kHz), inclusive
application/ flexboard
PSRR
2
Output Offset Voltage
VREF – VRF+, VREF – VRF–
VOFF1
–20
dVOFF/dT
–25
2.1
Output offset
2.2
Offset drift
1.65
V
A
15
µV/°C
C
V
C
V
C
–45
dB
C
–45
dB
C
+20
mV
C
+25
µV/°C
C
VCC –
0.9
0.3
0
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
4
ATR1841 [Preliminary]
9103AS–DVD–08/07
ATR1841 [Preliminary]
6. Two-wire Interface (TWI)
6.1
Slave Address
MSB
6.2
(ADS)
LSB
0
0
1
1
1
0
0
R/W = 0
Pin ADS = low (GND)
0
0
1
1
1
0
1
R/W = 0
Pin ADS = high (VCC)
Data
MSB
m1
6.3
LSB
m2
g1
g2
g3
g4
g5
g6
Mode Setting
The first two bits select the mode/gain level.
Table 6-1.
6.4
Mode Selection Register
m1
m2
Mode Select
1
1
High gain
1
0
Middle gain
0
1
Low gain
0
0
Sleep
Gain Setting
The last six bits are used to finely adjust the gain by ±6 dB
Table 6-2.
Gain Selection Register
g1
g2
g3
g4
g5
g6
Gain
1
1
1
1
1
1
+6 dB
1
0
0
0
0
0
0 dB
…
…
…
0
0
0
…
0
0
0
–6 dB
5
9103AS–DVD–08/07
7. Applications Recommendation
To achieve the best performance VCC needs to be blocked using a high quality capacitor
(C = 100 nF) as close to IC/pin as possible.
8. Photo Diode Arrangement
Figure 8-1.
Phote Diode Arrangement
D
D
Dimensions
500.0
µm
Photo diode is symmetrically centered
to the center of the chip and package
6
ATR1841 [Preliminary]
9103AS–DVD–08/07
ATR1841 [Preliminary]
9. Ordering Information
Extended Type Number
Package
Remarks
ATR1841-P1QN
QFN_OPEN_3x3_8L
Taped and reeled, Pb-free
10. Package Information
7
9103AS–DVD–08/07
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Atmel Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Atmel Europe
Le Krebs
8, Rue Jean-Pierre Timbaud
BP 309
78054
Saint-Quentin-en-Yvelines Cedex
France
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Technical Support
[email protected]
Sales Contact
www.atmel.com/contacts
Product Contact
Web Site
www.atmel.com
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF
THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2007 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, and others are registered trademarks or trademarks of
Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
9103AS–DVD–08/07
Similar pages