TDK B39861B3563U410 Saw filters for automotive electronic Datasheet

SAW filters for automotive
electronics
Series/Type:
B3563
The following products presented in this data sheet are being withdrawn.
Ordering Code
B39861B3563U410
Substitute Product
Date of Withdrawal
2016-01-08
Deadline Last
Orders
2016-04-15
Last Shipments
2016-07-15
For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The
addresses of our worldwide sales network are presented at www.epcos.com/sales.
SAW Components
B3563
SAW RF filter
864.00 MHz
Data sheet
Application
■
■
■
■
Low-loss RF filter for wireless audio application
Low amplitude ripple
High image frequency suppression
No matching network required for
operation at 50 Ω
Features
■
■
■
■
■
■
■
■
Package size 3.0 x 3.0 x 1.1 mm3
Package code DCC6C
RoHS compatible
Approximate weight 0.037 g
Package for Surface Mount Technology (SMT)
Ni, gold-plated terminals
Lead free soldering compatible with J - STD20C
Electrostactic Sensitive Device (ESD)
Pin configuration
■ 2
■ 5
■ 1, 3, 4, 6
Input
Output
To be grounded
Please read cautions and warnings and
important notes at the end of this document.
2
October 21, 2013
SAW Components
B3563
SAW RF filter
864.00 MHz
Data sheet
Characteristics
Temperature range for specification:
Terminating source impedance:
Terminating load impedance:
TA =
ZS =
ZL =
0 ˚C to +40 ˚C
50 Ω
50 Ω
min.
typ.
max.
—
@ 25 ˚C
864.00
—
MHz
Maximum insertion attenuation
αmax
862.50 ... 865.50 MHz
—
4.0
6.0
dB
Amplitude ripple (p-p)
∆α
862.50 ... 865.50 MHz
—
1.5
2.5
dB
Relative attenuation (relative to αmax)
αrel
841.60 ... 843.60 MHz
852.30 ... 853.30 MHz
879.00 ... 915.00 MHz
40.0
30.0
30.0
44.0
38.0
38.0
—
—
—
dB
dB
dB
—
–30
—
ppm/K
Center frequency
fC
Temperature coefficient of frequency
TCf
Maximum ratings
Operable temperature range TA
–45/+125 ˚C
Storage temperature range
Tstg
–45/+125 ˚C
DC voltage
VDC
6
V
Input power max.
PIN
0
dBm
Please read cautions and warnings and
important notes at the end of this document.
3
source impedance 50 Ω
October 21, 2013
SAW Components
B3563
SAW RF filter
864.00 MHz
Data sheet
Transfer function (passband)
Transfer function (wideband)
Please read cautions and warnings and
important notes at the end of this document.
4
October 21, 2013
SAW Components
B3563
SAW RF filter
864.00 MHz
Data sheet
ESD protection of SAW filters
SAW filters are Electro Static Discharge sensitive devices. To reduce the probability of damages
caused by ESD, special matching topologies have to be applied.
In general, “ESD matching” has to be ensured at that filter port, where electrostatic discharge is
expected.
Electrostatic discharges predominantly appear at the antenna input of RF receivers. Therefore
only the input matching of the SAW filter has to be designed to short circuit or to block the ESD
pulse.
Below three figures show recommended “ESD matching” topologies.
For wideband filters the high-pass ESD matching structure needs to be at least of 3rd order to
ensure a proper matching for any impedance value of antenna and SAW filter input. The required
component values have to be determined from case to case.
Cs3
Cs1
to output
matching
Lp2
Dp1
MLC1
Cs1
Fig. 1 MLC varistor plus ESD matching
Cs3
Lp2
to output
matching
Fig. 2 Suppressor diode plus ESD matching
In cases where minor ESD occur, following simplified “ESD matching” topologies can be used
alternatively.
Cs1
Cs3
to output
matching
Lp2
Fig. 3 3rd order high-pass structure for basic ESD protection
In all three figures the shunt inductor Lp2 could be replaced by a shorted microstrip with proper
length and width. If this configuration is possible depends on the operating frequency and
available pcb space.
Effectiveness of the applied ESD protection has to be checked according to relevant industry
standards or customer specific requirements
For further information, please refer to EPCOS Application report:
“ESD protection for SAW filters”.
This report can be found under www.epcos.com/rke.Click on “Applications Notes”.
Please read cautions and warnings and
important notes at the end of this document.
5
October 21, 2013
SAW Components
B3563
SAW RF filter
864.00 MHz
Data sheet
References
Type
B3563
Ordering code
B39861B3563U410
Marking and package
C61157-A7-A67
Packaging
F61074-V8168-Z000
Date codes
L_1126
S-parameters
B3563_NB.s2p, B3563_WB.s2p
See file header for port/pin assignment table.
Soldering profile
S_6001
RoHS compatible
RoHS-compatible means that products are compatible with the
requirements according to Art. 4 (substance restrictions) of Directive 2011/65/EU of the European Parliament and of the
Council of June 8th, 2011, on the restriction of the use of certain
hazardous substances in electrical and electronic equipment
("Directive") with due regard to the application of exemptions as
per Annex III of the Directive in certain cases.
Matching coils
See Inductor pdf-catalog
http://www.tdk.co.jp/tefe02/coil.htm#aname1
and Data Library for circuit simulation
http://www.tdk.co.jp/etvcl/index.htm
For further information please contact your local EPCOS sales office or visit our webpage at
www.epcos.com .
Published by EPCOS AG
Systems, Acoustics, Waves Business Group
P.O. Box 80 17 09, 81617 Munich, GERMANY
 EPCOS AG 2013. This brochure replaces the previous edition.
For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or
the international Representatives.
Due to technical requirements components may contain dangerous substances. For information on
the type in question please also contact one of our Sales Offices.
Please read cautions and warnings and
important notes at the end of this document.
6
October 21, 2013
Important notes
The following applies to all products named in this publication:
1.
2.
3.
4.
5.
6.
7.
Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately
incumbent on the customer to check and decide whether an EPCOS product with the
properties described in the product specification is suitable for use in a particular customer
application.
We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained
by third parties in the event of malfunction or failure of an electronic component.
The warnings, cautions and product-specific notes must be observed.
In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be
available. The aforementioned does not apply in the case of individual agreements deviating
from the foregoing for customer-specific products.
Unless otherwise agreed in individual contracts, all orders are subject to the current
version of the “General Terms of Delivery for Products and Services in the Electrical
Industry” published by the German Electrical and Electronics Industry Association
(ZVEI).
The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CeraPlas, CSMP, CSSP,
CTVS, DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC,
MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL,
SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap
are trademarks registered or pending in Europe and in other countries. Further information
will be found on the Internet at www.epcos.com/trademarks.
7
October 21, 2013
Similar pages