XP Power ECL15UD01 Ultra compact size Datasheet

ACDC
530 Watts
ECL Series
xppower.com
•
Ultra Compact Size
•
Single, Dual & Triple Outputs
•
Open Frame PCB & Chassis Mount
•
Encapsulated PCB & Chassis Mount
•
<0.3 W No Load Input Power
•
Peak Load Capability
•
3 Year Warranty
Specification
Input
• 85-264 VAC (120-370 VDC)
• 47-63 Hz
• ECL05: 0.1 A rms, ECL10: 0.2 A rms
ECL15: 0.3 A rms, ECL25: 0.4 A rms
ECL30: 0.8 A rms at 230 VAC
Inrush Current
• 20 A at 115 VAC, 40 A at 230 VAC,
cold start at 25 °C
Earth Leakage Current • Class II construction no earth
Power Factor
• EN61000-3-2, class A
No Load Input Power • <0.3 W
Input Protection
• ECL05/10: Internal T1 A/250 VAC fuse
ECL15/25/30: Internal T2 A/250 VAC fuse
Input Voltage
Input Frequency
Input Current
Output
• See tables
• ±5% on output 1 only, on multiple output
versions, V2 & V3 will track by same
percentage, (not ‘-E’ or ‘-S’ versions)
Initial Set Accuracy
• ±1% for output 1,
±1% for output 2 of UD01 & UD02 versions,
±5% for output 2 & output 3 of other versions
Minimum Load
• Single output versions: none,
Multi output versions:
UD01 & UD02: 10% V1 & V2
UD03: 10% V1, 20% V2
UT02 & UT03: 10% V1, 20% V2 & V3
to meet regulation specifications
Start Up Delay
• 3 s max
Start Up Rise Time
• 14 ms max
Hold Up Time
• 16 ms typical for single output versions,
12 ms typical for multiple output versions,
at full load & 115 VAC
Line Regulation
• ±0.5% max for single output versions and
output 1 of multiple output versions,
±0.9% max for output 2 & output 3 of
multiple output versions
Load Regulation
• 1% max for single output versions,
for multiple output versions (see note 5)
Cross Regulation
• Multi output versions only (see note 5)
Transient Response
• 4% max deviation, recovery to within
1% in 500 µs for a 25% load change
Ripple & Noise
• Single output versions:
3.3-5 V versions: 50 mV pk-pk,
12-15 V versions: 120 mV pk-pk,
24-48 V versions: 200 mV pk-pk,
Multiple output versions: 1% pk-pk on any
output, 20 MHz bandwidth
Overvoltage Protection • 115-140% Vnom, 195-216% Vnom
ECL05/10/15/25 with 3.3 V
Overload Protection
• Single output versions: ECL05/10/15:
120-150%, ECL25: 120-170% of total
power
Multiple output versions: 140-200% of
total power
Short Circuit Protection • Trip and restart (hiccup mode)
Temperature
• 0.05%/°C
Coefficient
Output Voltage
Output Voltage Trim
General
Efficiency
Isolation
Switching Frequency
Power Density
MTBF
•
•
•
•
See tables
3000 VAC Input to Output
70 kHz typical
ECL05: 2.25 W/In3 (PCB Mount version)
ECL10: 5.50 W/In3 (PCB Mount version)
ECL15: 5.30 W/In3 (PCB Mount version)
ECL25: 5.90 W/In3 (PCB Mount version)
ECL30: 7.10 W/In3 (PCB Mount version)
• ECL05/10: >450 kHrs,
ECL15/25/30: >400 kHrs,
to MIL-HDBK-217F at 25 °C, GB
Environmental
Operating Temperature • -20 °C to +70 °C, derate linearly from
100% at +50 °C to 50% at +70 °C
Cooling
• Convection-cooled
Operating Humidity
• 95% RH, non-condensing
Storage Temperature • -40 °C to +85 °C
Operating Altitude
• 3000 m
Vibration
• 2 g, 10 Hz to 500 Hz, 10 mins/cycle,
60 mins each cycle
EMC & Safety
Emissions
Harmonic Currents
Voltage Flicker
ESD Immunity
Radiated Immunity
•
•
•
•
•
EFT/Burst
Surge
•
•
Conducted Immunity
Magnetic Fields
Dips & Interruptions
•
•
•
Safety Approvals
•
EN55022, level B conducted & radiated
EN61000-3-2, class A
EN61000-3-3
EN61000-4-2, level 3 Perf Criteria A
EN61000-4-3, 10 V/m 80% mod
Perf Criteria A
EN61000-4-4, level 3, Perf Criteria A
EN61000-4-5, installation class 3,
Perf Criteria A
EN61000-4-6, 10 Vrms Perf Criteria A
EN61000-4-8, 10 A/m, Perf Criteria A
EN61000-4-11, 30% for 10 ms,
60% for 100 ms, 100% for 5000 ms
Perf Criteria A, B, B
IEC60950-1, EN60950-1, UL60950-1,
CSA22.2 No. 234 per cUL
Output Power
4.3
5.0
5.0
5.0
5.0
5.0
5.0
8.6
10.0
10.0
10.0
10.0
10.0
10.0
Output Current
Output Voltage
W
W
W
W
W
W
W
W
W
W
W
W
W
W
3.3
5.0
9.0
12.0
15.0
24.0
48.0
3.3
5.0
9.0
12.0
15.0
24.0
48.0
Nominal
1.30 A
1.00 A
0.55 A
0.41 A
0.33 A
0.21 A
0.10 A
2.60 A
2.00 A
1.10 A
0.83 A
0.67 A
0.42 A
0.21 A
VDC
VDC
VDC
VDC
VDC
VDC
VDC
VDC
VDC
VDC
VDC
VDC
VDC
VDC
Peak(1)
1.69 A
1.30 A
0.71 A
0.54 A
0.44 A
0.27 A
0.13 A
3.38 A
2.60 A
1.43 A
1.08 A
0.87 A
0.55 A
0.27 A
Efficiency
Model Number(2)
72%
75%
78%
78%
80%
82%
82%
72%
75%
78%
78%
80%
82%
82%
ECL05US03
ECL05US05
ECL05US09
ECL05US12
ECL05US15
ECL05US24
ECL05US48
ECL10US03
ECL10US05
ECL10US09
ECL10US12
ECL10US15
ECL10US24
ECL10US48
Notes
1. Peak load lasting <30 s with a maximum duty cycle of 10%, average output power not to exceed nominal.
2. Add suffix to model number to define type: add ‘-P’ for PCB mount, add ‘-T’ for chassis mount, add ‘-E’ for encapsulated.
Mechanical Details
Open Frame PCB Mount (P)
0.80
(20.3)
Encapsulated (E)
2.00
(50.8)
0.10
(2.5)
-Vo
ACL
V Adj.
0.10
(2.5)
0.10
(2.5)
0.91
(23.0)
+Vo
ACN
1.00
(25.4)
0.40
(10.1)
1.80
(45.7)
4 x ø 0.04 (ø1.0)
0.39
(10.0)
1.07 (27.2)
0.90
(22.9)
0.15
(3.8)
0.80 ±0.01 (20.32 ±0.3)
0.13 (3.4)
0.73
(18.5)
ACL
ø 0.07 (ø1.8)
ø 0.04 (ø1.0)
2.06
(52.4)
1.80
(45.7)
Open Frame Chassis Mount (T)
1.80 ±0.01 (45.72 ±0.3)
0.17
(4.4)
ACN
TOP VIEW
-Vo
+Vo
2.56 (65.0)
4-ø0.126 (ø3.20)
1.00
(25.4)
0.15
(4.0)
ACL
0.14
(3.5)
0.40 ±0.01 (10.16 ±0.3)
+Vo
-Vo
ACN
0.68
(17.4)
0.13
(3.40)
2.28 (58.0)
0.73
(18.5)
V Adj.
0.85
(21.6)
Notes
1. All dimensions in inches (mm).
2. Weight: ECL05/10 P Version: 0.057 lbs (26 g)
ECL05/10 T Version: 0.057 lbs (26 g)
ECL05/10 E Version: 0.13 lbs (60 g)
3. Tolerances: x.xx = ± 0.02 (x.x = ± 0.5)
x.xxx = ± 0.01 (x.xx = ± 0.25)
Mating Connectors (-T version only)
Input Connector: JST PHR-3
Output Connector: JST PHR-2
Crimps: SPH-002T-P0.5S
Cable harness with 300 mm wire available, order part no. ECL10 LOOM KIT
ACDC
ECL05/10
Models and Ratings
ACDC
ECL15
Models and Ratings
Output
Power
10 W
15 W
15 W
15 W
15 W
15 W
15 W
Output Current
Output
Voltage
3.3 VDC
5.0 VDC
9.0 VDC
12.0 VDC
15.0 VDC
24.0 VDC
48.0 VDC
Nominal
3.00 A
3.00 A
1.67 A
1.25 A
1.00 A
0.63 A
0.32 A
Peak(1)
3.90 A
3.90 A
2.17 A
1.62 A
1.30 A
0.82 A
0.41 A
Efficiency
Model Number(2,3)
75%
78%
80%
80%
80%
82%
82%
ECL15US03
ECL15US05
ECL15US09
ECL15US12
ECL15US15
ECL15US24
ECL15US48
Notes
1. Peak load lasting <30 s with a maximum duty cycle of 10%, average output power not to exceed nominal.
2. Add suffix to model number to define type: add ‘-P’ for PCB mount, add ‘-T’ for chassis mount, add ‘-E’ for encapsulated, add ‘-S’ for screw terminals.
3. A screw terminal version (-S) is available with DIN clip attached, add suffix ‘D’, e.g. ECL15US24-SD,
DIN rail mounting kit is available as a separate item, order code ECL15 DIN CLIP.
4. For medically-approved 15 W power supplies contact sales or see www.xppower.com for details of CU15-M series and VCP15 series.
Mechanical Details
Open Frame PCB Mount (P)
Encapsulated (E)
0.50
(12.6)
2.44
(62.0)
-Vo
-Vo
ACN
1.21
(30.7)
+Vo
0.69
(17.5)
ACL
0.15
(3.9)
0.06
(1.6)
1.31
(33.3)
0.79
(20.1)
0.79
(20.1)
0.69
(17.5)
2.13
(54.1)
2.56
(65.0)
0.36
(9.1)
0.21
(5.4)
0.96
(24.4)
0.78
(20.0) max
4x ø 0.04 (ø1.0)
ø 0.07 (ø1.8)
ø 0.04 (ø1.0)
0.39
(10.0)
Open Frame Chassis Mount (T)
Screw Terminal (S)
3.10 (78.7)
2.95 (75.0)
4-0.12 (3.2)
1.36
(34.5)
-Vo
0.95 ACN
(24.1)
ACL
1.25
(31.7)
+Vo
V Adj.
2.13
(54.1)
0.11
(2.9)
TOP VIEW
ACL
0.17
(4.4)
0.15
(3.8)
ACN
+Vo
TOP VIEW
ACN
1.00 ACL
(25.4)
4x ø 0.14
(4x ø 3.5)
-Vo
+Vo
0.44
(11.1)
0.15
(3.8)
0.15
(3.8)
2.80 (71.1)
V Adj.
2.54
(64.5)
0.39
(10.0)
1º
0.78
(20.0) max
0.91
(23.1)
1.04
(26.4)
0.27 0.09
(6.8) (2.5)
3.30 (84.0)
Optional
DIN clip
Notes
1. All dimensions in inches (mm).
2. Weight: ECL15 P Version: 0.07 lbs (35 g)
T Version: 0.07 lbs (35 g)
E Version: 0.20 lbs (90 g)
S Version: 0.24 lbs (110 g)
3. Tolerances: x.xx = ± 0.02 (x.x = ± 0.5)
x.xxx = ± 0.01 (x.xx = ± 0.25)
Mating Connectors (-T version only)
Input Connector: JST PHR-3
Output Connector: JST PHR-4
Crimps: SPH-002T-P0.5S
Cable harness with 300 mm wire available, order part no. ECL15 LOOM KIT
Output 1
Voltage
Current(2)
+12.0 V
0.65 A
+15.0 V
0.50 A
5.0 V(1)
1.50 A
5.0 V(1)
2.00 A
5.0 V(1)
2.00 A
Output Power
15
15
15
15
15
W
W
W
W
W
Output 2
Voltage
Current(2)
-12.0 V
0.650 A
-15.0 V
0.500 A
12.0 V(1)
0.625 A
+12.0 V
0.200 A
+15.0 V
0.150 A
Voltage
Output 3
Current(2)
-12.0 V
-15.0 V
Efficiency
82%
82%
81%
81%
81%
0.200 A
0.150 A
Model
Number(3,4)
ECL15UD01
ECL15UD02
ECL15UD03
ECL15UT02
ECL15UT03
Notes
1. Isolated output
2. Peak load of 130% lasting <30 s with a maximum duty cycle of 10%, average
output power not to exceed nominal.
3. Add suffix to model number to define type: add ‘-P’ for PCB mount, add ‘-T’
for chassis mount, add ‘-E’ for encapsulated, add ‘-S’ for screw terminals.
4. A screw terminal version (-S) is available with DIN clip attached, add suffix ‘D’
e.g. ECL15UT02-SD, DIN rail mounting kit is available as a separate item, order
code ECL15 DIN CLIP.
5. UD01/UD02: Load regulation <3%, 10-100% load.
Cross regulation <3%, one output fixed, the other varied from
10-100% load
UD03:
Load regulation <1% V1, <10% V2
Cross regulation <10% V2, V1 varied from 10-100% load
UT02/UT03: Load regulation <1% V1, <10% V2 & V3
Cross regulation <10% V2 & V3, V2 & V3 at 50% load & V1
varied from 20-100% load
Mechanical Details
Open Frame PCB Mount (P)
2.44 (62.0)
0.79 (20.0) max
Pin1
Pin2
0.29 (7.4)
2.13 (54.1)
0.25 (6.3)
Pin5
0.155 (3.9)
0.17 (4.4)
0.29 (7.4)
0.25 (6.3)
Pin4
ACL
0.15 (3.8)
Pin3
0.07 (1.8)
0.96 (17.5)
0.06 (1.6)
1.20 (30.7)
ACN
Pin
1
2
3
4
5
UD01/02
V2
NP
COM
V1
NP
UD03
NP
V2 RTN
V2
V1
V1 RTN
UT02/03
V3
COM
V2
V1
V1 RTN
UD03
NC
V2 RTN
V2
V1
V1 RTN
UT02/03
V3
COM
V2
V1
V1 RTN
7-ø0.04 (ø1.0)
NP = No pin.
7-ø0.07 (ø1.8)
Open Frame Chassis Mount (T)
Pin
1
2
3
4
5
0.91 (23.1)
1.25 (31.8)
ACL
0.95 (24.1)
NP
0.15 (3.8)
Pin1
Pin2
Pin3
Pin4
Pin5
ACN
0.79 (20.0)Max
4-ø0.13 (ø3.20)
UD01/02
V2
COM
COM
COM
V1
NC = No connection.
0.15 (3.81)
2.80 (71.1)
3.10 (78.7)
Encapsulated (E)
0.12 (3.1)
0.69 (17.5)
ACN
Top View
Pin3
Pin4
ACL
Pin5
4-ø0.04 (ø1.0)
0.54 (13.7)
C1
1.03 (26.3)
Pin4
ACL
0.44 (11.2)
Pin5
1.04 (26.4)
Pin3
1.36 (34.5)
Top View
1.18 (30.0)
Pin2
0.10 (2.5)
2.56 (65.1)
UT02/03
V3
COM
V2
V1
V1 RTN
UD03
NC
V2 RTN
V2
+V1
V1 RTN
UT02/03
V3
COM
V2
V1
V1 RTN
0.39 (10.0)
Pin1
0.18 (4.5)
UD03
NP
V2 RTN
V2
V1
V1 RTN
0.21 (5.4)
2-ø0.14 (ø3.5)
ACN
UD01/02
V2
NP
COM
V1
NP
NP = No pin.
2.13 (54.1)
Screw Terminal (S)
0.18 (4.6)
Pin
1
2
3
4
5
0.96 (24.4)
Pin2
1.31 (33.5)
0.25 (6.3)
Pin1
0.39 (10.0)
0.25 (6.3)
0.54 (13.7)
2.56 (65.0)
0.10 (2.5)
0.27 (6.8)
0.10 (2.5)
Optional
DIN clip
Pin
1
2
3
4
5
UD01/02
V2
COM
COM
COM
V1
NC = No connection.
2.95 (75.0)
3.31 (84.0)
Notes
1. All dimensions in inches (mm).
2. Tolerances: x.xx = ± 0.02 (x.x = ± 0.5)
x.xxx = ± 0.01 (x.xx = ± 0.25)
3. Weight: ECL15 UD/UT: P Version: 0.09 lbs (40 g)
T Version: 0.09 lbs (40 g)
E Version: 0.21 lbs(95 g)
S Version: 0.26 lbs (120 g)
Mating Connectors (-T version only)
Input Connector: JST PHR-3
Output Connector: JST XHP-5
ACDC
ECL15UD/UT
Models and Ratings
ACDC
ECL25
Models and Ratings
Output
Power
20 W
25 W
25 W
25 W
25 W
25 W
25 W
Output
Voltage
3.3 VDC
5.0 VDC
9.0 VDC
12.0 VDC
15.0 VDC
24.0 VDC
48.0 VDC
Output Current
Nominal
6.00 A
5.00 A
2.80 A
2.10 A
1.67 A
1.04 A
0.52 A
Peak(1)
7.80 A
6.50 A
3.64 A
2.73 A
2.17 A
1.35 A
0.68 A
Efficiency
Model Number(2,3)
75%
78%
80%
80%
80%
82%
82%
ECL25US03
ECL25US05
ECL25US09
ECL25US12
ECL25US15
ECL25US24
ECL25US48
Notes
1. Peak load lasting <30 s with a maximum duty cycle of 10%, average output
power not to exceed nominal.
2. Add suffix to model number to define type: add ‘-P’ for PCB mount, add ‘-T’
for chassis mount, add ‘-E’ for encapsulated, add ‘-S’ for screw terminals.
3. A screw terminal version (-S) is available with DIN clip attached, add suffix ‘D’,
e.g. ECL25US24-SD, DIN rail mounting kit is available as a separate item, order
code ECL25/30 DIN CLIP.
Mechanical Details
Open Frame PCB Mount (P)
Encapsulated (E)
2.96
(75.2)
0.13 (3.2)
ACN
ACN
-Vo
1.18
(30.0)
1.36
(34.6)
3.10
(78.7)
ACL
1.18
(30.0)
0.59
(15.0)
+Vo
-Vo
0.16
(4.1)
0.09
(2.3)
0.17
(4.4)
2.85
(72.4)
V Adj.
1.50
(38.1)
+Vo
ACL
0.05
(1.4)
0.59
(15.0)
TOP VIEW
2.85
(72.4)
0.09
(2.3)
0.88
(22.3) MAX
1.10
(27.9)
0.15
(3.8)
4x ø 0.04 (ø1.0)
ø0.04 (ø1.0)
0.39 (10.0)
ø0.07 (ø 1.8)
Open Frame Chassis Mount (T)
Screw Terminal (S)
3.46 (87.9)
3.43 (87.0)
4- 0.15 (3.81)
0.44
(11.2)
1.36
(34.6)
-Vo
1.10 ACN
(27.9) ACL
TOP VIEW
ACN
+Vo
ACL
1.57
(40.0)
0.13
(3.3)
0.13
(3.3)
3.20 (81.3)
0.88
(22.4) MAX
4x ø0.14
(4x ø3.5)
-Vo
0.84
(21.3)
1.20
+Vo
(30.5)
V Adj.
3.01
(76.4)
0.39 (10.0)
1.00
(25.4)
1º
1.12
(28.5)
0.27
(6.8)
0.10
(2.5)
3.78 (96.0)
Optional
DIN clip
Notes
1. All dimensions in inches (mm).
2. Weight: ECL25: P Version: 0.14 lbs (66 g)
T Version: 0.14 lbs (66 g)
E Version: 0.33 lbs (150 g)
S Version: 0.37 lbs (170 g)
3. Tolerances: x.xx = ± 0.02 (x.x = ± 0.5)
x.xxx = ± 0.01 (x.xx = ± 0.25)
Mating Connectors (-T version only)
Input Connector: JST XHP-3
Output Connector: JST XHP-6
Crimps: SXH-002T-P0.6
Cable harness with 300 mm wire available, order part no. ECL25 LOOM KIT
Output 1
Voltage
Current(2)
+12.0 V
1.3 A
+15.0 V
1.0 A
5.0 V(1)
3.0 A
5.0 V(1)
3.0 A
5.0 V(1)
3.0 A
Output Power
30
30
30
30
30
W
W
W
W
W
Output 2
Voltage
Current(2)
-12.0 V
1.30 A
-15.0 V
1.00 A
12.0 V(1)
1.30 A
+12.0 V
0.63 A
+15.0 V
0.50 A
Voltage
Output 3
Current(2)
-12.0 V
-15.0 V
0.63 A
0.50 A
Efficiency
84%
83%
81%
83%
81%
Model
Number(3,4)
ECL30UD01
ECL30UD02
ECL30UD03
ECL30UT02
ECL30UT03
Notes
1. Isolated output
2. Peak load of 130% lasting <30 s with a maximum duty cycle of 10%, average
output power not to exceed nominal.
3. Add suffix to model number to define type: add ‘-P’ for PCB mount, add ‘-T’
for chassis mount, add ‘-E’ for encapsulated, add ‘-S’ for screw terminals.
4. A screw terminal version (-S) is available with DIN clip attached, add suffix ‘D’
e.g. ECL30UT02-SD, DIN rail mounting kit is available as a separate item, order
code ECL25/30 DIN CLIP.
5. UD01/UD02: Load regulation <3%, 10-100% load.
Cross regulation <3%, one output fixed, the other varied from
10-100% load
UD03:
Load regulation <1% V1, <10% V2
Cross regulation <10% V2, V1 varied from 10-100% load
UT02/UT03: Load regulation <1% V1, <10% V2 & V3
Cross regulation <10% V2 & V3, V2 & V3 at 50% load & V1
varied from 20-100% load
Mechanical Details
Open Frame PCB Mount (P)
2.96 (75.2)
VR
Pin
1
2
3
4
5
0.29 (7.5)
Pin5
0.09 (2.3)
0.09 (2.3)
0.05 (1.4)
2.85 (72.4)
0.29 (7.5)
1.05 (26.7)
0.29 (7.5)
0.15 (3.8)
Pin4
ACL
0.29 (7.5)
1.18 (29.9)
Pin3
0.17 (4.4)
Pin2
ACN
1.36 (34.6)
0.88 (22.3) Max
Pin1
ø 0.04 (ø1.0)
UD01/02
NP
NP
V2
COM
V1
UD03
V1 RTN
V1
NP
V2 RTN
V2
UT02/03
-V1
+V1
V3
COM
V2
UD03
V1 RTN
V1
NC
V2 RTN
V2
UT02/03
-V1
+V1
V3
COM
V2
NP = No pin.
ø 0.07(ø1.8)
Open Frame Chassis Mount (T)
3.46 (87.9)
Pin
1
2
3
4
5
3.20 (81.3)
UD01/02
V2
COM
COM
COM
V1
NC = No connection.
0.12 (3.0)
ACL
1.00 (25.4)
NP
0.13 (3.3)
Pin1
Pin2
Pin3
Pin4
Pin5
ACN
0.88 (22.4) Max
4-ø0.15 (ø3.8)
1.36 (34.6)
VR
1.10 (27.9)
0.13 (3.3)
Encapsulated (E)
Pin4
Pin
1
2
3
4
5
1.10 (28.0)
0.39 (10.0)
Pin3
1.50 (38.1)
0.16 (4.1)
1.18 (29.9)
Pin2
Top View
0.59 (14.9)
ACN
0.59 (14.9)
0.29 (7.5)
0.29 (7.5)
Pin1
Pin5
ACL
7-ø0.04 (ø1.00)
0.12 (3.2)
UD01/02
NP
NP
V2
COM
V1
UD03
V1 RTN
V1
NP
V2 RTN
V2
UT02/03
-V1
+V1
V3
COM
V2
UD03
V1 RTN
V1
NC
V2 RTN
V2
UT02/03
-V1
+V1
V3
COM
V2
NP = No pin.
C0.04 (1.0)
2.85 (72.4)
3.10 (78.7)
Screw Terminal (S)
0.19 (4.8)
2-ø0.14(ø3.5)
0.39 (10.0)
Pin4
0.10
(2.5)
0.44 (11.2)
Pin5
Optional DIN clip
3.03 (77.0)
3.43 (87.0)
0.27
(6.8)
0.10 (4.5)
0.10 (4.5)
0.18 (4.5)
1.12 (28.5)
Pin3
ACL
1.39 (35.2)
Top View
1.57 (40.0)
Pin2
ACN
1.21 (30.7)
Pin1
Pin
1
2
3
4
5
UD01/02
V2
COM
COM
COM
V1
NC = No connection.
3.78 (96.0)
Notes
1. All dimensions in inches (mm).
2. Tolerances: x.xx = ± 0.02 (x.x = ± 0.5)
x.xxx = ± 0.01 (x.xx = ± 0.25)
3. Weight: ECL30 UD/UT: P Version: 0.13 lbs (60 g)
T Version: 0.13 lbs (60 g)
E Version: 0.34 lbs (155 g)
S Version: 0.39 lbs (175 g)
Mating Connectors (-T version only)
Input Connector: JST XHP-3
Output Connector: JST XHP-5
12-Nov-13
ACDC
ECL30UD/UT
Models and Ratings