Click on Series name for product info on aimtec.com Series AM1G-NZ 1 Watt | DC-DC Converter FEATURES: I/O Isolation of 1500 and 3000VDC Very low no load consumption Remote On/Off Control 8 pin SIP package Operating temperature -40 to +100oC Continuous Short circuit protection Wide 2:1 input range High efficiency up to 81% Models Single output Model Input Voltage (V) Output Voltage(V) Output Current max (mA) Isolation (VDC) Capacitor Load (μF) Efficiency (%) AM1G-0503S-NZ AM1G-0505S-NZ AM1G-0512S-NZ AM1G-0515S-NZ AM1G-0524S-NZ AM1G-1203S-NZ AM1G-1205S-NZ AM1G-1209S-NZ AM1G-1212S-NZ AM1G-1215S-NZ AM1G-2403S-NZ AM1G-2405S-NZ AM1G-2412S-NZ AM1G-2415S-NZ AM1G-2424S-NZ AM1G-4803S-NZ AM1G-4805S-NZ AM1G-4812S-NZ AM1G-4815S-NZ AM1G-0503SH30-NZ AM1G-0505SH30-NZ AM1G-0512SH30-NZ AM1G-0515SH30-NZ AM1G-1203SH30-NZ AM1G-1205SH30-NZ AM1G-1209SH30-NZ AM1G-1212SH30-NZ AM1G-1215SH30-NZ AM1G-2403SH30-NZ AM1G-2405SH30-NZ AM1G-2412SH30-NZ AM1G-2415SH30-NZ AM1G-2424SH30-NZ AM1G-4803SH30-NZ AM1G-4805SH30-NZ AM1G-4812SH30-NZ AM1G-4815SH30-NZ 4.5-9 4.5-9 4.5-9 4.5-9 4.5-9 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 4.5-9 4.5-9 4.5-9 4.5-9 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 3.3 5 12 15 24 3.3 5 9 12 15 3.3 5 12 15 24 3.3 5 12 15 3.3 5 12 15 3.3 5 9 12 15 3.3 5 12 15 24 3.3 5 12 15 303 200 83 67 42 303 200 111 83 67 303 200 83 67 42 303 200 83 67 303 200 83 67 303 200 111 83 67 303 200 83 67 42 303 200 83 67 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 2700 2200 1000 680 470 2700 2200 1800 1000 680 2700 2200 1000 680 470 2700 2200 1000 680 2700 2200 1000 680 2700 2200 1800 1000 680 2700 2200 1000 680 470 2700 2200 1000 680 72 72 76 75 74 75 77 79 80 80 75 77 81 79 77 75 76 81 80 72 72 76 75 75 77 79 80 80 75 77 81 79 77 75 76 81 80 www.aimtec.com F 051e R8 Tel: +1 514 620 2722 1 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1G-NZ 1 Watt | DC-DC Converter Models Dual output Model Input Voltage (V) Output Voltage(V) Output Current max (mA) Isolation (VDC) Capacitor Load (μF) Efficiency (%) AM1G-0505D-NZ AM1G-0512D-NZ AM1G-0515D-NZ AM1G-1205D-NZ AM1G-1212D-NZ AM1G-1215D-NZ AM1G-2405D-NZ AM1G-2409D-NZ AM1G-2412D-NZ AM1G-2415D-NZ AM1G-4805D-NZ AM1G-4812D-NZ AM1G-4815D-NZ AM1G-0505DH30-NZ AM1G-0512DH30-NZ AM1G-0515DH30-NZ AM1G-1205DH30-NZ AM1G-1212DH30-NZ AM1G-1215DH30-NZ AM1G-2405DH30-NZ AM1G-2412DH30-NZ AM1G-2415DH30-NZ AM1G-4805DH30-NZ AM1G-4812DH30-NZ AM1G-4815DH30-NZ 4.5-9 4.5-9 4.5-9 9-18 9-18 9-18 18-36 18-36 18-36 18-36 36-75 36-75 36-75 4.5-9 4.5-9 4.5-9 9-18 9-18 9-18 18-36 18-36 18-36 36-75 36-75 36-75 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±9 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 ±100 ±42 ±33 ±100 ±42 ±33 ±100 ±56 ±42 ±33 ±100 ±42 ±33 ±100 ±42 ±33 ±100 ±42 ±33 ±100 ±42 ±33 ±100 ±42 ±33 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 ±1000 ±470 ±330 ±1000 ±470 ±330 ±1000 ±680 ±470 ±330 ±1000 ±470 ±330 ±1000 ±470 ±330 ±1000 ±470 ±330 ±1000 ±470 ±330 ±1000 ±470 ±330 73 76 75 78 81 80 80 80 80 80 76 80 80 73 76 75 78 81 80 80 80 80 76 80 80 Input Specifications Parameters Voltage range Nominal Typical 5 12 24 48 4.5-9 9-18 18-36 36-75 Peak Input Voltage time Filter Maximum Units VDC 1 sec Capacitor 5 Vin 12 Vin 24 Vin 48 Vin 5 Vin 12 Vin 24 Vin 48 Vin 5 Vin 12 Vin 24 Vin 48 Vin Maximum Rating No load input current Input Reflected Ripple Current On/Off Control* 12 25 50 100 25 12 6 4 30 40 55 70 ON – open or Isolated; OFF – high voltage level (current 5-10mA) VDC mA mA *Note: Exceeding 20mA of control current will permanently damage the converter. Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance www.aimtec.com F 051e R8 Conditions Typical 60sec, <1mA > 1000 30 120 3000VDC Isolation,100kHz, 0.1V 1500VDC Isolation,100kHz, 0.1V Tel: +1 514 620 2722 2 of 5 Rated Units 1500, 3000 VDC MOhm pF Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1G-NZ 1 Watt | DC-DC Converter Output Specifications Parameters Voltage accuracy No Load Voltage accuracy Voltage balance Short Circuit Protection Short Circuit Restart Line voltage regulation Load voltage regulation Temperature coefficient Transient Recovery Time Transient Response Deviation Ripple Noise Conditions Typical 5 to 100% load ±2 ±5 ±0.5 Continuous Automatic restart ±0.5 ±0.6 ±0.02 2 ±5 50 90 Dual Output balanced load LL~HL load 5~100% 25% load step 25% load step At 20MHz Bandwidth At 20MHz Bandwidth Maximum Units % % % % %/oC msec % mV p-p mV p-p General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 200 KHz oC Operating temperature With derating above 85oC -40 to +100 oC Storage temperature -55 to +125 oC Case Temperature 105 oC Lead Temperature 1.5mm from case for 10 Seconds 300 Cooling Free air convection Humidity 95 % Case material Plastic (UL94V-0 rated) Weight 4.9 g Dimensions (L x Wx H) 0.87 x 0.37 x 0.47 inch, 22 x 9.5 x 12 mm MTBF >1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Pin Out Specifications Dimensions Pin Single Dual 1 2 3 5 6 7 8 - V Input + V Input On/Off Control N.C. + V Output - V Output CS - V Input + V Input On/Off Control N.C. + V Output Common - V Output 22.00 (0.87) PRINTED FACE 12.00 (0.47) 12.00 (0.47) 0.50 (0.02) 4.10 (0.16) 2.54 (0.10) 2.50 (0.98) www.aimtec.com F 051e R8 9.50 (0.37) 0.50 (0.02) 1 2 3 2.10 (0.08) Tel: +1 514 620 2722 3 of 5 5 6 7 8 0.300 (0.012) 9.50 (0.37) 0.50 (0.02) Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1G-NZ 1 Watt | DC-DC Converter Derating Free Air Convection 85º C Output Power (%) 100 80 Safe Operating Area 60 40 20 0 - 20 - 40 0 20 40 60 80 85 105 100 Ambient Temperature º C Load Recommended EMC Circuit Model C1 C2 C4 LDM MOV TVS 5 Vin 4.7µF / 50V 4.7µF / 50V 1nF /3KV 12 µH - SMCJ13A 12 Vin 4.7µF / 50V 4.7µF / 50V 1nF /3KV 12 µH - SMCJ28A 24 Vin 4.7µF / 100V 4.7µF / 50V 1nF /3KV 12 µH S14K35 SMCJ48A 48 Vin 4.7µF / 100V 4.7µF / 100V 1nF /3KV 12 µH S14K60 SMCJ90A C3 680µF / 16V 680µF / 25V 330µF / 50V 330µF / 100V LDM2 56µH 56µH Cd 47nF /100V 47nF /100V 47nF /100V 47nF /100V D1 RB160M60/1A RB160M60/1A RB160M60/1A RB160M60/1A R1 See Formula See Formula See Formula See Formula Note: Fuse is user selectable R1 = ((Vcd – Vd1 – 1.0) / Icntl)‐ 300 www.aimtec.com F 051e R8 Tel: +1 514 620 2722 4 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1G-NZ 1 Watt | DC-DC Converter Recommended Circuits Single Output +Vout LDM + Vin 6 2 C1 C2 CNTL Cout 3 D1 R1 C3 ‐ Vin DC 8 DC 1 Cs 7 ‐ Vout Dual Output + Vin 6 2 C1 +Vout LDM1 LDM C2 CNTL 3 D1 R1 C3 ‐ Vin DC DC Cout GND 7 Cout LDM1 1 8 ‐ Vout Model 5 Vin 12 Vin 24 Vin 48 Vin C1 100µF 100µF 10µF 10µF C2 47µF 47µF 1µF 1µF LDM 4.7 - 12 µH 4.7 - 12 µH 4.7 - 12 µH 4.7 - 12 µH C3 47µF / 100V 47µF / 100V 47µF / 100V 47µF / 100V D1 RB160M-60/1A RB160M-60/1A RB160M-60/1A RB160M-60/1A R1 See Formula See Formula See Formula See Formula LDM1 2.2 - 10 µH 2.2 - 10 µH 2.2 – 10 µH 2.2 - 10 µH CS 10 - 22µF 10 - 22µF 10 - 22µF 10 - 22µF Cout 100µF 100µF 100µF 100µF R1 = ((Vcd – Vd1 – 1.0) / Icntl)‐ 300 NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R8 Tel: +1 514 620 2722 5 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only