ES1Z - ES1F FAST RECOVERY RECTIFIER DIODES VOLTAGE RANGE: 200- 1500V CURRENT: 0.7 A Features ! ! Low cost ! Diffused junction Low leakage ! ! ! Low forward voltage drop High current capability Easily cleaned with Freon,Alcohol,Isopropanol B A A and similar solvents C Mechanical Data ! ! ! ! ! ! D Case: D O - 4 1 Molded Plastic Terminals: Plated Leads Solderable per MIL-STD-202, Method 208 Polarity: Cathode Band DO-41 Dim Min Max Weight: 0.34 grams (approx.) A 25.40 ¾ Mounting Position: Any Marking: Type Number B 4.06 5.21 C 0.71 0.864 D 2.00 2.72 All Dimensions in mm Maximum Ratings and Electrical Characteristics TA = 25C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forw ard rectified current 9.5mm lead length, @TA=75 Peak forw ard surge current 8.3ms single half-sine-w ave superimposed on rated load @TJ =125 Maximum instantaneous forw ard voltage @ 0.5/0.7A Maximum reverse current at rated DC blocking voltage @TA=25 @TA=100 Symbol ES1Z ES1 ES1A ES1F Unit VRRM 200 400 600 1500 V VRMS 140 280 420 1050 V V DC 200 400 600 1500 V IF(AV) 0.7 A IFSM 30.0 A VF 2.5 V 5.0 IR 100.0 A Maximum reverse recovery time (Note1) t rr 350 ns Typical junction capacitance (Note2) CJ 15 pF Typical thermal resistance (Note3) RθJA 50 TJ -55----+150 TSTG -55---- +150 Operating junction temperature range Storage temperature range ／Ｗ NOTE:1. Measured with I F=0.5A, I R=1A, I rr=0.25A. 2. Measured at 1.0MHz and applied rev erse v oltage of 4.0V DC. 3. Thermal resistance f rom junction to ambient. 1 of 2 www.sunmate.tw FIG.1 -- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM trr 10 N.1. 50 N.1. +0.5A D.U.T. ( - ) 0 PULSE GENERATOR (NOTE2) (+) 50VDC (APPROX) (-) OSCILLOSCOPE (NOTE 1) 1 N.1. -0.25A ( + ) -1.0A NOTES: 1. RISETIME= 7ns MAX. INPUT IMPEDANCE= 1M . 22PF 2. RISETIME= 10ns MAX. SOURCEIMPEDANCE= 50 FIG.3 -- TYPICAL FORWARD CHARACTERISTIC INSTANTANEOUS FORWARD CURRENT AMPERES AVERAGE FORWARD CURRENT AMPERES FIG.2 -- FORWARD DERATING CURVE 1.0 ES1Z ES1 ES1A 0.8 ES1F 0.6 0.4 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.2 0 0 25 50 75 100 125 150 100 10 1.0 0.4 JUNCTION CAPACITANCE,pF PEAK FORWARD SURGE CURRENT AMPERES ES1~ ES1A 0.2 0.1 0.06 0.04 0.02 0.01 1.0 2.0 3.0 4.0 5.0 FIG.5-- TYPICAL JUNCTION CAPACITANCE 30 20 E S1 Z E S1 E S1 A 10 E S1 F 10 ES1F~ ES1Z 2 INSTANTANEOUS FORWARD CURRENT, VOLTS FIG.4-- PEAK FORWARD SURGE CURRENT 5 T J =25 Pulse Width=300 µ S 4 AMBIENT TEMPERATURE, 0 1 1cm SET TIMEBASEFOR50/100 ns /cm 50 NUMBER OF CYCLES AT 60Hz 100 60 40 20 10 4 TJ=25 f=1MHz 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 REVERSE VOLTAGE,VOLTS 2 of 2 www.sunmate.tw