Datasheet 1 Channel Compact High Side Switch ICs 1.0A Current Limit High Side Switch ICs BD2240G BD2241G General Description Key Specifications BD2240G and BD2241G are low ON-Resistance high-side power switches N-Channel MOSFETs for Universal Serial Bus (USB) applications. These ICs have built-in over-current protection, thermal shutdown, under-voltage lockout and soft-start. Features Input Voltage Range: 2.7V to 5.5V ON-Resistance: 110mΩ(Typ) Over-Current Threshold: 0.82A (Min), 1.12A (Max) Standby Current: 0.01μA (Typ) Operating Temperature Range: -40°C to +85°C Package W(Typ) D(Typ) H (Max) Built-in Low ON-Resistance (Typ 110mΩ) N-Channel MOSFET Over-Current Detection Thermal Shutdown Open-Drain Fault Flag Output Flag Output Delay Under-Voltage Lockout Soft-Start Circuit Output Discharge Function Reverse Current Protection when Power Switch Off Control Input Logic Active-High: BD2240G Active-Low: BD2241G SSOP5 2.90mm x 2.80mm x 1.25mm Applications USB Hub in Consumer Appliances, PC, PC Peripheral Equipment, and so forth Typical Application Circuit 5V (Typ) 3.3V 10kΩ to 100kΩ CIN IN OUT GND EN CL + - /OC Lineup Over-Current Threshold Min Typ Max Control Input Logic 0.82A 0.97A 1.12A High SSOP5 Reel of 3000 BD2240G-GTR 0.82A 0.97A 1.12A Low SSOP5 Reel of 3000 BD2241G-GTR Package Orderable Part Number ○Product structure：Silicon monolithic integrated circuit ○This product has not designed protection against radioactive rays .www.rohm.com TSZ02201-0E3E0H300300-1-2 © 2013 ROHM Co., Ltd. All rights reserved. 1/23 TSZ22111・14・001 21.Aug.2014 Rev.003 BD2240G BD2241G Block Diagram OUT IN Pin Configurations BD2240G TOP VIEW 1 IN BD2241G TOP VIEW OUT 5 2 GND 2 GND /OC 4 3 EN OUT 5 1 IN 3 /EN /OC 4 Pin Description Pin No. Symbol I/O 1 IN - Switch input and the supply voltage for the IC 2 GND - Ground 3 EN, /EN I Enable input EN: High level input turns on the switch. (BD2240G) /EN: Low level input turns on the switch. (BD2241G) 4 /OC O Over-current detection terminal. Low level output during over-current or over-temperature condition Open-drain fault flag output 5 OUT O Switch output www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 Function 2/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Absolute Maximum Ratings (Ta= 25°C) Parameter IN Supply Voltage EN(/EN) Input Voltage /OC Voltage /OC Sink Current Symbol Rating Unit V IN -0.3 to +6.0 V V EN , V /EN -0.3 to +6.0 V V /OC -0.3 to +6.0 V I /OC 5 mA OUT Voltage V OUT -0.3 to +6.0 V Storage Temperature Tstg -55 to +150 °C Power Dissipation Pd 0.67 (Note 1) W (Note 1) Mounted on 70mm x 70mm x 1.6mm glass epoxy board. Reduce 5.4mW per 1°C above 25°C Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. Recommended Operating Conditions Parameter Symbol Rating Min Typ Max Unit IN Operating Voltage V IN 2.7 5.0 5.5 V Operating Temperature Topr -40 - +85 °C Electrical Characteristics BD2240G (V IN = 5V, Ta= 25°C, unless otherwise specified.) DC Characteristics Parameter Operating Current Standby Current Symbol I DD Limit Unit Min Typ Max - 110 160 μA Conditions V EN = 5V, V OUT = open I STB - 0.01 5 μA V EN = 0V, V OUT = open V ENH 2.0 - - V High Input V ENL - - 0.8 V Low Input EN Input Leakage I EN -1 +0.01 +1 μA V EN = 0V or 5V ON-Resistance R ON - 110 155 mΩ I OUT = 500mA Reverse Leak Current I REV - - 1.0 μA V OUT = 5.0V, V IN = 0V Over-Current Threshold I TH 820 970 1120 mA Short Circuit Output Current I SC 500 650 850 mA Output Discharge Resistance R DISC 30 60 120 Ω I DISC = 1mA /OC Output Low Voltage V /OC - - 0.4 V I /OC = 0.5mA V TUVH 2.1 2.3 2.5 V V IN Increasing V TUVL 2.0 2.2 2.4 V V IN Decreasing EN Input Voltage UVLO Threshold V OUT = 0V, RMS AC Characteristics Parameter Symbol Limit Min Typ Max Unit Conditions Output Rise Time t ON1 - 1 6 ms R L = 20Ω Output Turn ON Time t ON2 - 1.5 10 ms R L = 20Ω Output Fall Time t OFF1 - 1 20 μs R L = 20Ω Output Turn OFF Time t OFF2 - 3 40 μs R L = 20Ω /OC Delay Time t /OC 10 15 20 ms www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 3/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Electrical Characteristics - continued BD2241G (V IN = 5V, Ta= 25°C, unless otherwise specified.) DC Characteristics Parameter Symbol Limit Min Typ Max Unit Conditions Operating Current I DD - 110 160 μA V /EN = 0V, V OUT = open Standby Current I STB - 0.01 5 μA V /EN = 5V, V OUT = open V /ENH 2.0 - - V High Input V /ENL - - 0.8 V Low Input /EN Input Leakage I /EN -1 +0.01 +1 μA V /EN = 0V or 5V ON-Resistance R ON - 110 155 mΩ I OUT = 500mA Reverse Leak Current I REV - - 1.0 μA V OUT = 5.0V, V IN = 0V Over-Current Threshold I TH 820 970 1120 mA Short Circuit Output Current I SC 500 650 850 mA Output Discharge Resistance R DISC 30 60 120 Ω I DISC = 1mA /EN Input Voltage /OC Output Low Voltage UVLO Threshold V OUT = 0V, RMS V /OC - - 0.4 V I /OC = 0.5mA V TUVH 2.1 2.3 2.5 V V IN Increasing V TUVL 2.0 2.2 2.4 V V IN Decreasing AC Characteristics Parameter Symbol Limit Unit Conditions Min Typ Max t ON1 - 1 6 ms R L = 20Ω Output Turn ON Time t ON2 - 1.5 10 ms R L = 20Ω Output Fall Time t OFF1 - 1 20 μs R L = 20Ω Output Turn OFF Time t OFF2 - 3 40 μs R L = 20Ω /OC Delay Time t /OC 10 15 20 ms Output Rise Time www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 4/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Measurement Circuit VIN VIN A A IN OUT GND VEN(/EN) EN(/EN) A. OUT IN 1µF 1µF RL GND VEN(/EN) /OC Operating Current B. EN(/EN) /OC EN, /EN Input Voltage, Output Rise / Fall Time VIN VIN 10kΩ A A IOC IN OUT IN 1µF VEN(/EN) C. EN(/EN) 1µF IOUT GND OUT GND VEN(/EN) /OC ON-Resistance, Over-Current Detection D. EN(/EN) /OC /OC Output Low Voltage Figure 1. Measurement Circuit Timing Diagram VEN VENL VENH tON2 90% 10% tOFF1 90% 10% 10% tON1 tOFF1 Figure 3. Output Rise / Fall Time (BD2241G) Figure 2. Output Rise / Fall Time (BD2240G) www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 tOFF2 90% VOUT 10% tON1 V/ENH V/ENL tON2 tOFF2 90% VOUT V/EN 5/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Typical Performance Curves 140 Ta=25°C 120 Operating CURRENT Current : IDD:[μA] OPERATING IDD [μA] Operating Current : IDD[μA] OPERATING CURRENT : IDD [μA] 140 100 80 60 40 20 2 3 4 5 SUPPLY VOLTAGE VIN [V] Supply Voltage : VIN:[V] 1.0 60 40 20 -50 0 50 100 AMBIENT : Ta[℃] AmbientTEMPERATURE Temperature : Ta[°C] Figure 5. Operating Current vs Ambient Temperature (EN, /EN Enable) 1.0 Ta=25°C StandbyCURRENT Current : ISTB STB[μA] STANDBY : I[μA] [μA] 80 6 Figure 4. Operating Current vs Supply Voltage (EN, /EN Enable) Standby Current : I 100 0 0 STANDBY CURRENTSTB : ISTB[μA] VIN=5.0V 120 0.8 0.6 0.4 0.2 VIN=5.0V 0.8 0.6 0.4 0.2 0.0 0.0 2 3 4 5 SUPPLY IN [V] SupplyVOLTAGE Voltage : V:INV[V] -50 6 Figure 7. Standby Current vs Ambient Temperature (EN, /EN Disable) Figure 6. Standby Current vs Supply Voltage (EN, /EN Disable) www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 0 50 100 AMBIENT TEMPERATURE : Ta[ ] Ambient Temperature : Ta[°C]℃ 6/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Typical Performance Curves - continued 2.0 Ta=25°C 1.5 Enable INPUT Input Voltage : VEN,: V V/ENEN[V] [V] ENABLE VOLTAGE Enable INPUT Input Voltage : VEN:,VV/EN EN[V] ENABLE VOLTAGE [V] 2.0 Low to High High to Low 1.0 0.5 0.0 VIN=5.0V Low to High 1.5 High to Low 1.0 0.5 0.0 2 3 4 5 Supply Voltage : VIN:[V] SUPPLY VOLTAGE VIN [V] 6 -50 Figure 8. EN, /EN Input Voltage vs Supply Voltage (VENH, VENL, V/ENH, V/ENL) 100 Figure 9. EN, /EN Input Voltage vs Ambient Temperature (VENH, VENL, V/ENH, V/ENL) 200 Ta=25°C ON-Resistance : R: ON [mΩ] ON RESISTANCE RON [mΩ] ON-Resistance [mΩ] ON ON RESISTANCE: :RRON [mΩ] 200 0 50 Ambient Temperature : Ta[°C] AMBIENT TEMPERATURE : Ta[℃] 150 100 50 0 VIN=5.0V 150 100 50 0 2 3 4 5 SUPPLY IN [V] SupplyVOLTAGE Voltage : V:INV[V] 6 -50 Figure 10. ON-Resistance vs Supply Voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 0 50 100 AMBIENT TEMPERATURE : Ta[℃] Ambient Temperature : Ta[°C] Figure 11. ON-Resistance vs Ambient Temperature 7/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Typical Performance Curves - continued 1.3 Ta=25°C Over-Current Threshold: ITH[A] TH OVER CURRENT THRESHOLD:I [A] Over-Current ITH[A] TH [A] OVER CURRENTThreshold: THRESHOLD:I 1.3 1.2 1.1 1.0 0.9 0.8 0.7 VIN=5.0V 1.2 1.1 1.0 0.9 0.8 0.7 2 3 4 5 SUPPLY VOLTAGE : VIN [V] Supply Voltage : VIN[V] 6 -50 0 50 AMBIENT : Ta[℃] Ambient TEMPERATURE Temperature : Ta[°C] Figure 12. Over-Current Threshold vs Supply Voltage Figure 13. Over-Current Threshold vs Ambient Temperature 0.9 [A] Ta=25°C SC 0.8 Short Circuit Output Cuurent: I Short Circuit Output Current: I SC [A] 0.9 100 0.7 0.6 0.5 0.4 VIN=5.0V 0.8 0.7 0.6 0.5 0.4 0.3 0.3 2 3 4 5 Supply Voltage : VIN [V] -50 6 Figure 14. Short Circuit Output Current vs Supply Voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 0 50 Ambient Temperature : Ta[℃] 100 Figure 15. Short Circuit Output Current vs Ambient Temperature 8/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Typical Performance Curves - continued 100 Ta=25°C /OC Output Low V/OC /OC [mV] [mV] /OC OUTPUT LOWVoltage: VOLTAGE:V /OC Output Low V/OC /OC [mV] /OC OUTPUT LOWVoltage: VOLTAGE:V [mV] 100 80 60 40 20 0 2 3 4 5 SUPPLY VOLTAGE VIN [V] Supply Voltage : VIN:[V] VIN=5.0V 80 60 40 20 0 6 -50 Figure 16. /OC Output Low Voltage vs Supply Voltage Figure 17. /OC Output Low Voltage vs Ambient Temperature 1.0 UVLO Hysteresis Voltage: VHYS[V] UVLO HYSTERESIS VOLTAGE:VHSY[V] 2.5 UVLO Threshold: VTUVH, VTUVL [V] UVLO THRESHOLD : VTUVH , VTUVL[V] 0 50 100 AMBIENT : Ta[℃] AmbientTEMPERATURE Temperature : Ta[°C] 2.4 2.3 VTUVH 2.2 VTUVL 2.1 2.0 -50 0 50 AmbientTEMPERATURE Temperature: Ta [°C] AMBIENT : Ta[℃] 100 0.6 0.4 0.2 0.0 -50 Figure 18. UVLO Threshold Voltage vs Ambient Temperature www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 0.8 0 50 100 AmbientTEMPERATURE Temperature: Ta [°C] AMBIENT : Ta[℃] Figure 19. UVLO Hysteresis Voltage vs Ambient Temperature 9/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Typical Performance Curves - continued 5.0 Ta=25°C 4.0 Output Rise Time : tON1[ms] RISE TIME : TON1[ms] Output : t[ms] ON1[ms] RISERise TIMETime : TON1 5.0 3.0 2.0 1.0 VIN=5.0V 4.0 3.0 2.0 1.0 0.0 0.0 2 3 4 5 Supply VOLTAGE Voltage: VIN: V [V] SUPPLY IN [V] -50 6 Figure 20. Output Rise Time vs Supply Voltage Figure 21. Output Rise Time vs Ambient Temperature 5.0 Ta=25°C Output Turn ON TimeON2 : t [ms] TURN ON TIME : T ON2 [ms] Output Turn ON Time ON2 : t [ms] TURN ON TIME : T ON2 [ms] 5.0 0 50 100 AMBIENT Ta[℃] AmbientTEMPERATURE Temperature: Ta :[°C] 4.0 3.0 2.0 1.0 0.0 VIN=5.0V 4.0 3.0 2.0 1.0 0.0 2 3 4 5 SUPPLY IN [V] Supply VOLTAGE Voltage : V:INV [V] 6 -50 Figure 22. Output Turn ON Time vs Supply Voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 0 50 100 AMBIENT TEMPERATURE : Ta[℃] Ambient Temperature : Ta[°C] Figure 23. Output Turn ON Time vs Ambient Temperature 10/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Typical Performance Curves - continued 5.0 Ta=25°C 4.0 Output Time : tOFF1 FALL Fall TIME : TOFF1 [μs][μs] Output Fall TimeOFF1 FALL TIME : T : tOFF1 [μs][μs] 5.0 3.0 2.0 1.0 0.0 VIN=5.0V 4.0 3.0 2.0 1.0 0.0 2 3 4 5 SUPPLY IN [V] SupplyVOLTAGE Voltage : V:INV[V] -50 6 Figure 24. Output Fall Time vs Supply Voltage Figure 25. Output Fall Time vs Ambient Temperature 6.0 Ta=25°C 5.0 Output Turn OFF Time : tOFF2[μs] TURN OFF TIME : TOFF2[μs] Output Time tOFF2 [μs] TURNTurn OFFOFF TIME : T:OFF2 [μs] 6.0 0 50 100 AMBIENT TEMPERATURE : Ta[℃] Ambient Temperature : Ta[°C] 4.0 3.0 2.0 1.0 0.0 VIN=5.0V 5.0 4.0 3.0 2.0 1.0 0.0 2 3 4 5 SUPPLY VOLTAGE : V IN Supply Voltage : VIN[V] [V] 6 -50 Figure 26. Output Turn OFF Time vs Supply Voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 0 50 100 AMBIENT TEMPERATURE : Ta[ ] Ambient Temperature : Ta[°C] ℃ Figure 27. Output Turn OFF Time vs Ambient Temperature 11/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Typical Performance Curves - continued 20 Ta=25°C 18 /OC DELAY TIME:t:/OC [ms] /OC /OC Delay TIME Time: [ms] [ms] /OC DDLAY Tt/OC /OC DELAY TIME :t:/OC [ms] /OC /OC Delay TIME Time: [ms] /OC DDLAY Tt/OC [ms] 20 16 14 12 10 VIN=5.0V 18 16 14 12 10 2 3 4 5 IN SUPPLY VOLTAGE : V Supply Voltage: VIN [V][V] 6 -50 200 100 Figure 29. /OC Delay Time vs Ambient Temperature 200 Ta=25°C Output Resistance: RDISC DISCDischarge ON RESISTANCE : RDISC [Ω][Ω] Ω] [Ω] Output Discharge Resistance: R[DISC DISC ON RESISTANCE : RDISC Figure 28. /OC Delay Time vs Supply Voltage 0 50 AMBIENT TEMPERATURE Ambient Temperature: Ta: Ta[ [°C]℃] 150 100 50 0 VIN=5.0V 150 100 50 0 2 3 4 5 [V] SUPPLY VOLTAGE VIN[V] Supply Voltage: V: IN 6 -50 Figure 30. Output Discharge Resistance vs Supply Voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 0 50 100 AMBIENT : Ta[℃] AmbientTEMPERATURE Temperature: Ta [°C] Figure 31. Output Discharge Resistance vs Ambient Temperature 12/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Typical Wave Forms (BD2240G) VEN VEN (5V/div.) (5V/div.) V/OC V/OC (5V/div.) (5V/div.) VOUT VOUT (5V/div.) (5V/div.) VIN=5V RL=20Ω VIN=5V RL=20Ω IOUT IOUT (0.5A/div.) (0.5A/div.) TIME(1μs/div.) TIME(1ms/div.) Figure 33. Output Fall Characteristic Figure 32. Output Rise Characteristic VEN V/OC (5V/div.) (5V/div.) V/OC VOUT (5V/div.) (5V/div.) CL=220μF CL=100μF IOUT IOUT (0.2A/div.) CL=47μF (0.5A/div.) VIN=5V RL=20Ω VIN=5V TIME (1ms/div.) TIME (5ms/div.) Figure 34. Inrush Current Response Figure 35. Over-Current Response Ramped Load www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 13/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Typical Wave Forms – continued VEN VEN (5V/div.) (5V/div.) V/OC V/OC (5V/div.) (5V/div.) VOUT VOUT (5V/div.) (5V/div.) IOUT IOUT (0.5A/div.) (0.5A/div.) VIN=5V VIN=5V TIME (5ms/div.) TIME (100ms/div.) Figure 36. Over-Current Response Enable to Short Circuit Figure 37. Over-Current Response Enable to Short Circuit VOUT (5V/div.) VIN (5V/div.) V/OC (5V/div.) VOUT (5V/div.) VIN=5V IOUT IOUT (0.2A/div.) (1A/div.) RL=20Ω TIME (5ms/div.) TIME (10ms/div.) Figure 38. Over-Current Response 1ΩLoad Connected at EN Figure 39. UVLO Response when Increasing VIN www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 14/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Typical Wave Forms – continued VIN (5V/div.) VOUT (5V/div.) IOUT (0.2A/div.) RL=20Ω TIME (10ms/div.) Figure 40. UVLO Response when Decreasing VIN www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 15/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Typical Application Circuit 10kΩ to 100kΩ CIN Controller 5V (Typ) IN OUT OUT GND EN(/EN) CL + - /OC Application Information When excessive current flows due to output short-circuit or so, ringing occurs by inductance of power source line and IC. This may cause bad effects on IC operations. In order to avoid this case, a bypass capacitor (C IN ) should be connected across the IN terminal and GND terminal of IC. A 1μF or higher value is recommended. Moreover, in order to decrease voltage fluctuations of power source line and IC, connect a low ESR capacitor in parallel with C IN. A 10μF to 100μF or higher is effective. Pull up /OC output by resistance 10kΩ to 100kΩ. Set up values for C L which satisfies the application. This application circuit does not guarantee its operation. When using the circuit with changes to the external circuit constants, make sure to leave an adequate margin for external components including AC/DC characteristics as well as dispersion of the IC. Functional Description 1. Switch Operation IN terminal and OUT terminal are connected to the drain and the source of switch MOSFET respectively. The IN terminal is also used as power source input to internal control circuit. When the switch is turned ON from EN(/EN) control input, the IN and OUT terminals are connected by a 110mΩ (Typ) switch. In ON status, the switch is bidirectional. Therefore, when the potential of OUT terminal is higher than that of IN terminal, current flows from OUT to IN terminal. On the other hand, when the switch is turned off, it is possible to prevent current from flowing reversely from OUT to IN terminal since a parasitic diode between the drain and the source of switch MOSFET is not present. 2. Thermal Shutdown Circuit (TSD) If over-current would continue, the temperature of the IC would increase drastically. If the junction temperature goes beyond 135°C (Typ) in the condition of over-current detection, thermal shutdown circuit operates and turns power switch off, causing the IC to output a fault flag (/OC). Then, when the junction temperature decreases lower than 115°C (Typ), the power switch is turned on and fault flag (/OC) is cancelled. This operation repeats, unless the increase of chip’s temperature is removed or the output of power switch is turned OFF. The thermal shutdown circuit operates when the switch is ON (EN(/EN) signal is active). 3. Over-Current Detection (OCD) The over-current detection circuit limits current (I SC ) and outputs fault flag (/OC) when current flowing in each switch MOSFET exceeds a specified value. The over-current detection circuit works when the switch is on (EN(/EN) signal is active). There are three types of response against over-current: (1) (2) (3) When the switch is turned on while the output is in shortcircuit status When the switch is turned on while the output is in shortcircuit status or so, the switch gets in current limit status immediately. When the output shortcircuits while the switch is on When the output shortcircuits or high-current load is connected while the switch is on, very large current will flow until the over-current limit circuit reacts. When the current detection and limit circuit works, current limitation is carried out. When the output current increases gradually When the output current increases gradually, current limitation does not work until the output current exceeds the over-current detection value. When it exceeds the detection value, current limitation is carried out. 4. Under-Voltage Lockout (UVLO) UVLO circuit prevents the switch from turning on until the V IN exceeds 2.3V(Typ). If V IN drops below 2.2V(Typ) while the switch is still ON, then UVLO shuts off the power switch. UVLO has a hysteresis of 100mV(Typ). Under-voltage lockout circuit operates when the switch is on (EN(/EN) signal is active). www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 16/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G 5. Fault Flag (/OC) Output Fault flag output is N-MOS open drain output. During detection of over-current and/or thermal shutdown, the output level will turn low. Over-current detection has delay filter. This delay filter prevents current detection flags from being sent during instantaneous events such as inrush current at switch on or during hot plug. . If fault flag output is unused, /OC pin should be connected to open or ground line. 6. Output Discharge Function When the switch is turned off from disable control input or UVLO function, the 60Ω(Typ.) discharge circuit between OUT and GND turns on. By turning on this switch, electric charge at capacitive load is discharged. But when the voltage of IN declines extremely, then the OUT pin becomes Hi-Z without UVLO function. Over Current Detection Over Current Load Removed VOUT ITH ISC IOUT t/OC V/OC Figure 41. Over-Current Detection VEN Output Short Circuit VOUT Thermal Shutdown IOUT V/OC /OC Delay Time Figure 42. Over-Current Detection, Thermal Shutdown Timing (BD2240G) V/EN Output Short Circuit VOUT Thermal Shutdown IOUT V/OC /OC Delay Time Figure 43. Over-Current Detection, Thermal Shutdown Timing (BD2241G) www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 17/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Power Dissipation (SSOP5 package) 700 POWER DISSIPATION : Pd [mW] Power Dissipation : Pd[mW] 600 500 400 300 200 100 0 0 50 75 85 100 AMBIENT TEMPERATURE : Ta [℃] 25 125 150 Ambient Temperature : Ta[°C] 70mm x 70mm x 1.6mm Glass Epoxy Board Figure 44. Power Dissipation Curve (Pd-Ta Curve) I/O Equivalence Circuit Symbol Pin No. EN (/EN) 3 OUT 5 Equivalence Circuit EN (/EN) OUT /OC /OC www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 4 18/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply pins. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Thermal Consideration Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 6. Recommended Operating Conditions These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 7. In rush Current 8. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 9. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 10. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 19/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Operational Notes - continued 11. Unused Input Pins Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power supply or ground line. 12. Regarding the Input Pin of the IC This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a parasitic diode or transistor. For example (refer to figure below): When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode. When GND > Pin B, the P-N junction operates as a parasitic transistor. Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be avoided. Resistor Transistor (NPN) Pin A Pin B C Pin A N P+ N P N P+ N Parasitic Elements N P+ GND E N P N P+ B N C E Parasitic Elements P Substrate P Substrate Parasitic Elements Pin B B Parasitic Elements GND GND Figure 45. Example of monolithic IC structure N Region close-by GND 13. Ceramic Capacitor When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with temperature and the decrease in nominal capacitance due to DC bias and others. 14. Thermal Shutdown Circuit(TSD) This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always be within the IC’s power dissipation rating. If however the rating is exceeded for a continued period, the junction temperature (Tj) will rise which will activate the TSD circuit that will turn OFF all output pins. When the Tj falls below the TSD threshold, the circuits are automatically restored to normal operation. Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from heat damage. 15. Thermal design Perform thermal design in which there are adequate margins by taking into account the power dissipation (Pd) in actual states of use. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 20/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Ordering Information B D 2 2 4 0 Part Number B D G - GTR Package G: SSOP5 2 2 4 1 Part Number G Packaging and forming specification G: Halogen free TR: Embossed tape and reel - GTR Package G: SSOP5 Packaging and forming specification G: Halogen free TR: Embossed tape and reel Marking Diagram SSOP5 (TOP VIEW) Part Number Marking LOT Number Part Number Part Number Marking BD2240G J8 BD2241G J9 www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 21/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Physical Dimension, Tape and Reel Information Package Name www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 SSOP5 22/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 BD2240G BD2241G Revision History Date Revision 11.Mar.2013 16.Apr.2013 001 002 21.Aug.2014 003 www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 Changes New Release Ordering information is revised. Applied the ROHM Standard Style and improved understandability. Improved Symbol name. The title of figure 36 changed. Improved Regarding Input Pins of the IC in Operational Notes. Add Figure 14 and 15. Add Output Discharge Function explanation at page17. 23/23 TSZ02201-0E3E0H300300-1-2 21.Aug.2014 Rev.003 Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice – GE © 2013 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice – GE © 2013 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2014 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet BD2240G - Web Page Buy Distribution Inventory Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS BD2240G SSOP5 3000 3000 Taping inquiry Yes