ZigBit™ 2.4 GHz Amplified Wireless Modules ................................................................................................................... ATZB-A24-UFL/U0 Datasheet 8228B–MCU Wireless–06/09 ZigBit™ 2.4 GHz Amplified Wireless Modules 1-2 8228B–MCU Wireless–06/09 Table of Contents Section 1 1.1 Summary............................................................................................................................ 1-1 1.2 Applications........................................................................................................................ 1-1 1.3 Key Features...................................................................................................................... 1-2 1.4 Benefits .............................................................................................................................. 1-2 1.5 Abbreviations and Acronyms ............................................................................................. 1-2 1.6 Related Documents ........................................................................................................... 1-4 Section 2 2.1 Overview ............................................................................................................................ 2-5 Section 3 3.1 Electrical Characteristics.................................................................................................... 3-7 3.1.1 Absolute Maximum Ratings ................................................................................. 3-7 3.1.2 Test Conditions.................................................................................................... 3-7 3.1.3 RF Characteristics ............................................................................................... 3-8 3.1.4 ATmega1281V Microcontroller Characteristics ................................................... 3-8 3.1.5 Module Interfaces characteristics ........................................................................ 3-8 3.2 Physical/Environmental Characteristics and Outline ......................................................... 3-9 3.3 Pin Configuration ............................................................................................................. 3-10 3.4 Mounting Information ....................................................................................................... 3-14 3.5 Soldering Profile............................................................................................................... 3-14 3.6 Antenna Reference Design.............................................................................................. 3-15 Section 4 4.1 Ordering Information ........................................................................................................ 4-16 ZigBit™ 2.4 GHz Amplified Wireless Modules i 8228B–MCU Wireless–06/09 Section 1 Introduction 1.1 Summary ZigBit™ Am p is an ultra-comp act, extended ran ge, low-power, hig h-sensitivity 2.4GHz IEEE 802.15.4/ZigBee® OEM module from Atmel. Based on the innovative Atmel's mixed-signal hardware platform, this module is enhanced by an output power amplifier and an input low-noise amplifier, and is designed for wireless sensing, monitoring & control and data acquisition applications. ZigBit Amp modules eliminate the need for costly and time-consuming RF development, and shortens time to market for wireless applications with extended range requirements. Two different versions of ZigBit 2.4 GHz Amplified modules are available: ATZB-A24-UFL with built-in U.FL antenna connector and the ATZB-A24-U0 with unbalanced RF output. These modules are an addition to the ZigBit family represented by ATZB-24-A2 and ATZB-24-B0. In addition Atmel offer the ZigBit 900 MHz Wireless Module ATZB-900-B0 [2]. 1.2 Applications ZigBit module is compatible with robust IEEE 802.15.4/ZigBee stack that supports a self-healing, selforganizing mesh network, while optimizing network traffic and minimizing power consumption. Atmel offers two stack configurations: BitCloud and SerialNet. BitCloud is a ZigBee PRO certified software development platform supporting reliable, scalable, and secure wireless applications running on Atmel’s ZigBit modules. SerialNet allows programming of the module via serial AT-command interface. The applications include, but are not limited to: • Building automation & monitoring • • • • • • • – Lighting controls – Wireless smoke and CO detectors – Structural integrity monitoring HVAC monitoring & control Inventory management Environmental monitoring Security Water metering Industrial monitoring – Machinery condition and performance monitoring – Monitoring of plant system parameters such as temperature, pressure, flow, tank level, humidity, vibration, etc. Automated meter reading (AMR) ZigBit™ 2.4 GHz Amplified Wireless Modules 1-1 8228B–MCU Wireless–06/09 Introduction 1.3 Key Features • • • • • • • • • • • 1.4 Benefits • • • • • • • • • 1.5 Ultra compact size (38.0 x 13.5 x 2.0 mm) High RX sensitivity (-104 dBm) Outperforming link budget (up to 124 dB) Up to +20 dBm output power Very low power consumption: – < 6 µA in Sleep mode, – 23 mA in RX mode, – 50 mA in TX mode Ample memory resources (128K bytes of flash memory, 8K bytes RAM, 4K bytes EEPROM) Wide range of interfaces (both analog and digital): – 9 spare GPIO, 2 spare IRQ lines – 4 ADC lines + 1 line for supply voltage control (up to 9 lines with JTAG disabled) – UART with CTS/RTS control – USART – I2C – SPI – 1-Wire – Up to 30 lines configurable as GPIO Capability to use MAC address written into EEPROM IEEE 802.15.4 compliant transceiver 2.4 GHz ISM band BitCloud embedded software, including serial bootloader and AT command set Extended range through additional PA and LNA Ultra low power consumption combined with unprecedented range Rapid design-in with built-in U.FL connector (ATZB-A24-UFL) Flexibility in using a different external antenna for every application Small physical footprint and low profile for optimum fit in even the smallest of devices Mesh networking capability Easy-to-use low cost Development Kit Single source of support for HW and SW Worldwide license-free operation Abbreviations and Acronyms ADC Analog-to -Digital Converter API Application Programming Interface DC Direct Current DTR Data Terminal Ready EEPROM Electrically Erasable Programmable Read-Only Memory ESD Electrostatic Discharge ZigBit™ 2.4 GHz Amplified Wireless Modules 1-2 8228B–MCU Wireless–06/09 Introduction GPIO General Purpose Input/Output HAF High Frequency HVAC Heating, Ventilating and Air Conditioning HW Hardware 2 IC Inter-Integrated Circuit IEEE Institute of Electrical and Electrionics Engineers IRQ Interrupt Request ISM Industrial, Scientific and Medical radio band JTAG Digital interface for debugging of embedded device, also known as IEEE 1149.1 standard interface LNA Low Noise Amplifier MAC Medium Access Control layer MCU Microcontroller Unit. In this document it also means the processor, which is the core of ZigBit module NRE Network layer OEM Non-Recurring Engineering OTA Over-The-Air upgrade PA Power Amplifier PCB Printed Circuit Board PER Package Error Ratio RAM Random Access Memory RF Radio Frequency RTS/CTS Request to Send/ Clear to Send RX Receiver SMA Surface Mount Assembly SPI Serial Peripheral Interface SW Software TTM Time To Market TX Transmitter UART Universal Asynchronous Receiver/Transmitter USART Universal Synchronous/Asynchronous Receiver/Transmitter USB Universal Serial Bus ZDK ZigBit Development Kit ZigBee, ZigBee PRO Wireless networking standards targeted at low-power applications 802.15.4 The IEEE 802.15.4-2003 standard applicable to low-rate wireless Personal Area Network ZigBit™ 2.4 GHz Amplified Wireless Modules 1-3 8228B–MCU Wireless–06/09 Introduction 1.6 Related Documents [1] ZigBit™ 2.4 GHz Wireless Modules ATZB-24-B0/A2. Product datasheet. Atmel’s doc8226.pdf [2]. ZigBit™ 700/800/900 MHz Wireless Modules ATZB-900-B. Product datasheet. Atmel’s doc8227.pdf [3] ZigBit™ Development Kit. User's Guide. MeshNetics Doc. S-ZDK-451~01 [4] Atmel 8-bit AVR Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash. 2549F AVR 04/06 [5] Atmel Low-Power Transceiver for ZigBee Applications. AT86RF230 datasheet. doc5131.pdf [6] Ultra Small Surface Mount Coaxial Connectors - Low Profile 1.9mm or 2.4mm Mated Height. http://www.hirose.co.jp/cataloge_hp/e32119372.pdf [7] ZigBit™ Amp Development Kit. User's Guide. MeshNetics Doc. S-ZDK-451~02 [8] IEEE Std 802.15.4-2003 IEEE Standard for Information technology - Part 15.4 Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs) [9] ZigBee Specification. ZigBee Document 053474r17, October 19, 2007 [10] BitCloud™ IEEE 802.15.4/ZigBee Software. Product User Guide. Atmel’s doc8199.pdf ZigBit™ 2.4 GHz Amplified Wireless Modules 1-4 8228B–MCU Wireless–06/09 Section 2 Zigbit™ Module Overview 2.1 Overview ZigBit™ Amp is an extended-range, low-power, high sensitivity IEEE 802.15.4/ZigBee OEM module, which occupies less than a square inch of space. Based on a solid combination of Atmel's latest MCU Wireless hardware platform, power amplifier and low-noise amplifier, the ZigBit Amp offers an unmatched combination of superior radio performance, ultra-low power consumption and exceptional ease of integration. Figure 2-1. ATZB-A24-UFL/UN Block Diagram VCC (1.8 - 3.6V) IRQ UART USART/SPI I2C JTAG ANALOG PA AT86RF230 RF Transceiver ATmega1281 GPIO Antenna RF I/O SW SW LNA SPI Bus ZigBit Amp modules contains Atmel's ATmega1281V Microcontroller [4] and AT86RF230 RF Transceiver [5]. The module features 128K bytes flash memory and 8K bytes RAM. The compact all-in-one-chip integration of output Power Amplifier and input Low-Noise Amplifier, along with RF switches enables digital control of an external RF front-end to dramatically improve ZigBit's range performance on signal transmission and increase its sensitivity. This ensures stable connectivity with larger coverage area without significant increase in module size. The HF U.FL coaxial connector [6] used in the ATZB-A24-UFL module enables the user to choose appropriate external antenna for every type of application. ZigBit Amp already contains a complete RF/MCU design with all the necessary passive components included. The module can be easily mounted on a simple 2-layer PCB with a minimum of required external connection. Compared to a custom RF/MCUsolution, a module-based solution offers considerable savings in development time and NRE cost per unit during the design, prototyping, and mass production phases of product development. ZigBit™ 2.4 GHz Amplified Wireless Modules 2-5 8228B–MCU Wireless–06/09 Zigbit™ Module Overview To jumpstart evaluation and development, Atmel also offers a complete set of evaluation and development tools. The new ZigBit Amp Development Kit [7] (ATZB-DK-A24) comes with everything you need to create custom applications featuring ZigBit Amp module. The kit features MeshBean development boards with an easy-to-access extension connector for attaching third party sensors and other peripherals, and a JTAG connector for easy application uploading and debugging. The kit also includes reference applications to speed up application development, source code for hardware interface layer and reference drivers for the all the module interfaces, intuitive development environment from Atmel, and comprehensive set of application notes and product tutorials. ZigBit Amp modules comes bundled with BitCloud, a 2nd generation embedded software stack from Atmel. BitCloud is fully compliant with ZigBee PRO and ZigBee standards for wireless sensing and control [7], [8], [9], and it provides an augmented set of APIs which, while maintaining 100% compliance with the standard, offer extended functionality designed with developer's convenience and ease-of-use in mind. Depending on end-user design requirements, ZigBit Amp can operate as a self-contained sensor node, where it would function as a single MCU, or it can be paired with a host processor driving the module over a serial interface. In the former case, a user application may be used with the BitCloud software allowing customization of embedded applications through BitCloud's C API. In the latter case, the host processor controls data transmission and manages module peripherals via an extensive set of SerialNet AT commands. Thus, no firmware customization is required for a successful module design-in. Additionally, third-party sensors can be connected directly to the module, thus expanding the existing set of peripheral interfaces. ZigBit™ 2.4 GHz Amplified Wireless Modules 2-6 8228B–MCU Wireless–06/09 Section 3 Specifications 3.1 Electrical Characteristics 3.1.1 Absolute Maximum Ratings Table 3-1. Absolute Maximum Ratings(1)(2) Parameters Min Max Voltage on any pin, except RESET with respect to Ground -0.5V VCC + 0.5V DC Current per I/O Pin 40 mA DC Current DVCC and DGND pins 300 mA Input RF Level +5 dBm Notes: 1. Absolute Maximum Ratings are the values beyond which damage to the device may occur. Under no circumstances must the absolute maximum ratings given in this table be violated. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only. Functional operation of the device at these or other conditions, beyond those indicated in the operational sections of this specification, is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. Attention! ZigBit AMP is an ESD-sensitive device. Precaution should be taken when handling the device in order to prevent permanent damage. 3.1.2 Test Conditions , Table 3-2. Test conditions (unless otherwise stated) F = 2.45 GHz, VCC = 3V, Tamb = 25°C Parameters Supply Voltage, VCC Current Consumption: RX mode (1) Current Consumption: TX mode Current Consumption: Power-save mode Note: (1) Range Unit 3.0 to 3.6 V 23 mA 50 mA <6 µA 1. The parameters are measured under the following conditions: a) RMS, BitCloud Software is running at 4 MHz clock rate, DTR line management is turned off b) All interfaces are set to the default state (see Pin Assignment Table) c) Output TX power (when measuring consumption in TX mode) is +20dBm d) JTAG is not connected ZigBit™ 2.4 GHz Amplified Wireless Modules 3-7 8228B–MCU Wireless–06/09 Specifications Current consumption actually depends on multiple factors, including but not limited to, the board design and materials, BitCloud settings, network activity, EEPROM read/write operations. It also depends on MCU load and/or peripherals used by an application. 3.1.3 RF Characteristics Table 3-3. RF Characteristics Parameters Condition Frequency Band Unit 2.4000 to 2.4835 GHz Numbers of Channels 16 Channel Spacing 5 MHz Adjusted in 16 steps +10 to +20 dBm PER = 1% -104 dBm 250 kbps Unbalanced output 50 Ω With external 2.2 dBi antenna Up to 4000 m Condition Range Unit 128K bytes On-chip RAM size 8K bytes On-chip EEPROM size 4K bytes 4 MHz Range Unit 38.4 kbps 10/200 Bits/µs >1 MΩ 1.0 to VCC - 3 V 0 - VREF V Transmitter Output Power (1) Receiver Sensitivity On-Air Data Rate TX Output/ RX Input Nominal Impedance Range, outdoors Note: 3.1.4 Range 1. Preliminary data ATmega1281V Microcontroller Characteristics Table 3-4. ATmega1281V Characteristics Parameters On-chip Flash Memory size Operation Frequency 3.1.5 Module Interfaces characteristics Table 3-5. Module Interfaces characteristics Parameters Condition UART Maximum Baud Rate ADC Resolution/ Conversion Time ADC Input Resistance ADC Reference Voltage (VREF) ADC Input Voltage ZigBit™ 2.4 GHz Amplified Wireless Modules In single conversion mode 3-8 8228B–MCU Wireless–06/09 Specifications Table 3-5. Module Interfaces characteristics Parameters Condition 2 I C Maximum Clock GPIO Output Voltage (High/Low) -10/ 5 mA Real Time Oscillator Frequency 3.2 Range Unit 222 kHz 2.3/ 0.5 V 32.768 kHz Physical/Environmental Characteristics and Outline Parameters Size Operating Temperature Range Operating Relative Humidity Range Note: Value Comments 38.0 x 13.5 x 2.0 mm ATZB-A24-UFL/U0 -20°C to +70°C -40°C to +85°C operational(1) no more than 80% 1. Minor degration of clock stability may occur. Figure 3-1. ATZB-A24-UFL/U0 Mechanical drawing ZigBit™ 2.4 GHz Amplified Wireless Modules 3-9 8228B–MCU Wireless–06/09 Specifications 3.3 Pin Configuration Figure 3-2. ATZB-A24-UFL Pinout Figure 3-3. ATZB-A24-U0 Pinout ZigBit™ 2.4 GHz Amplified Wireless Modules 3-10 8228B–MCU Wireless–06/09 Specifications Table 3-6. Pin descriptions Connector Pin 1 2 3 4 Pin Name Description SPI_CLK SPI_MISO SPI_MOSI GPIO0 I/O Reserved for stack operation (4) O Reserved for stack operation (4) I/O Reserved for stack operation (4) I/O Default State after Power on General Purpose digital Input/Output 0 (2)(3)(4)(7) I/O tri-state (2)(3)(4)(7) I/O tri-state tri-state 5 GPIO1 General Purpose digital Input/Output 1 6 GPIO2 General Purpose digital Input/Output 2(2)(3)(4)(7) I/O 7 OSC32K_OUT 32.768 kHz clock output(4)(5) O (4) 8 RESET 9,22,23 DGND Digital Ground 10 CPU_CLK RF clock output. When module is in active state, 4 MHz signal is present on this line. While module is in the sleeping state, clock generation is also stopped(4). O 11 I2C_CLK I2C Serial clock output(2)(3)(4)(7) O tri-state I/O tri-state I tri-state O tri-state 12 I2C_DATA 13 UART_TXD Reset input (active low) 2 I C Serial data input/output (2)(3)(4)(7) UART receive input(1)(2)(3)(4)(7) 14 UART_RXD 15 UART_RTS RTS input (Request to send) for UART hardware flow control. Active low(2)(3)(4)(7) I tri-state 16 UART_CTS CTS output (Clear to send) for UART hardware flow control. Active low(2)(3)(4)(7)(8) O tri-state 17 GPIO6 General Purpose digital Input/Output 6(2)(3)(4)(7) I/O tri-state 18 GPIO7 (2)(3)(4)(7) General Purpose digital Input/Output 7 I/O tri-state 19 GPIO3 General Purpose digital Input/Output 3(2)(3)(4)(7) I/O tri-state 20 GPIO4 General Purpose digital Input/Output 4(2)(3)(4)(7) I/O tri-state GPIO5 (2)(3)(4)(7) General Purpose digital Input/Output 5 I/O tri-state 24,25 D_VCC (9) 26 JTAG_TMS 21 27 28 29 30 31 JTAG_TDI JTAG_TDO JTAG_TCK ADC_INPUT_3 ADC_INPUT_2 UART transmit output (1)(2)(3)(4)(7) Digital Supply Voltage (VCC) JTAG Test Mode Select(2)(3)(4)(6) (2)(3)(4)(6) JTAG Test Data Input JTAG Test Data Output JTAG Test Clock (2)(3)(4)(6) (2)(3)(4)(6) I I O I ADC Input Channel 3 (2)(3)(7) I tri-state ADC Input Channel 2 (2)(3)(7) I tri-state ADC Input Channel 1 (2)(3)(7) I tri-state 32 ADC_INPUT_1 33 BAT ADC Input Channel 0, used for battery level measurement. This pin equals VCC/3.(2)(3)(7) I tri-state 34 A_VREF Input/Output reference voltage for ADC I/O tri-state ZigBit™ 2.4 GHz Amplified Wireless Modules 3-11 8228B–MCU Wireless–06/09 Specifications Table 3-6. Pin descriptions Default State after Power on Connector Pin Pin Name Description 35 AGND Analog ground 36 GPIO9/1_WR General Purpose digital input/output 9 / 1-wire interface(2)(3)(4)(7) I/O 37 UART_DTR DTR input (Data Terminal Ready) for UART. Active low(2)(3)(4)(7) I tri-state 38 USART0_RXD USART/SPI Receive pin(2)(3)(4)(7) I tri-state 39 USART0_TXD (2)(3)(4)(7) O tri-state 40 USART0_EXTCLK USART/SPI External Clock(2)(3)(4)(7)(11) I/O tri-state 41 GPIO8 General Purpose Digital Input/Output 42 IRQ_7 USART /SPI Transmit pin I/O I/O tri-state (2)(3)(4)(7) I tri-state (2)(3)(4)(7) I tri-state Digital Input Interrupt request 7 43 IRQ_6 44,45,51,52, 53,56,57 DGND Digital ground 46,47 VRR Receiver supply voltage(9) 48,50 RF GND RF Analog Ground(2)(3)(4)(7) 49 RFP_IO Differential RF Input/Output(10) 54,55 Notes: VTT Digital Input Interrupt request 6 Transmitter supply voltage I/O (9) 1. The UART_TXD pin is intended for input (i.e. its designation as "TXD" implies some complex system containing ZigBit Amp as its RF terminal unit), while UART_RXD pin, vice versa is for output. 2. Most of pins can be configured for general purpose I/O or for some alternate functions as described in details in the ATmega1281V Datasheet [3]. 3. GPIO pins can be programmed either for output, or for input with/without pull-up resistors. Output pin drivers are strong enough to drive LED displays directly (refer to figures on pages 387-388, [3]). 4. All digital pins are provided with protection diodes to D_VCC and DGND 5. It is strongly recommended to avoid assigning an alternate function for OSC32K_OUT pin because it is used by BitCloud. However, this signal can be used if another peripheral or host processor requires 32.768 kHz clock, otherwise this pin can be disconnected. 6. Normally, JTAG_TMS, JTAG_TDI, JTAG_TDO, JTAG_TCK pins are used for on-chip debugging and flash burning. They can be used for A/D conversion if JTAGEN fuse is disabled. 7. The following pins can be configured with the BitCloud software to be general-purpose I/O lines: GPIO1, GPIO2, GPIO3, GPIO4, GPIO5, GPIO6, GPIO7, GPIO8, GPIO_1WR, I2C_CLK, I2C_DATA, UART_TXD, UART_RXD, UART_RTS, UART_CTS, ADC_INPUT_3, ADC_INPUT_2, ADC_INPUT_1, BAT, UART_DTR, USART0_RXD, USART0_TXD, USART0_EXTCLK, IRQ_7, IRQ_6. Additionally, four JTAG lines can be programmed with software as GPIO as well, but this requires changing the fuse bits and will disable JTAG debugging. 8. With BitCloud, CTS pin can be configured to indicate sleep/active condition of the module thus providing mechanism for power management of host processor. If this function is necessary, connection of this pin to external pull-down resistor is recommended to prevent the undesirable transients during module reset process. ZigBit™ 2.4 GHz Amplified Wireless Modules 3-12 8228B–MCU Wireless–06/09 Specifications 9. Using ferrite bead and 1 µF capacitor located closely to the power supply pin is recommended, as shown below. 10. Pins 48, 49 and 50 are featured for ATZB-A24-U0 module only. 11. In SPI mode, USART0_EXTCLK is output. In USART mode, this pin can be configured as either input or output pin. ZigBit™ 2.4 GHz Amplified Wireless Modules 3-13 8228B–MCU Wireless–06/09 Specifications 3.4 Mounting Information The below diagrams show the PCB layout recommended for ZigBit Amp module. Neither via-holes nor wires are allowed on the PCB upper layer in area occupied by the module. As a critical requirement, RF_GND pins should be grounded via several holes to be located right next to pins thus minimizing inductance and preventing both mismatch and losses. Figure 3-4. 3.5 ATZB-A24-UFL/U0 PCB Recommended Layout, Top View Soldering Profile The J-STD-020C-compliant soldering profile is recommended according to Table 3-7. Table 3-7. Soldering profile(1) Note: Profile Feature Green package Average ramp-up rate (217°C to peak) 3°C/s max Preheat tempearture 175°C ± 25°C 180s max Temperature maintained above 217°C 60s to 150s Time within 5°C of actual peak temperature 20s to 40s Peak temperature range 260°C Ramp-down rate 6°C/s max Time within 25°C to peak temperature 8 minuts max 1. The package is backward compatible with PB/Sn soldering profile. ZigBit™ 2.4 GHz Amplified Wireless Modules 3-14 8228B–MCU Wireless–06/09 Specifications 3.6 Antenna Reference Design Multiple factors affect proper antenna match, hence, affecting the antenna pattern. The particular factors are the board material and thickness, shields, the material used for enclosure, the board neighborhood, and other components adjacent to antenna. General Recommendations: Metal enclosure should not be used. Using low profile enclosure might also affect antenna tuning. Placing high profile components next to antenna should be avoided. Having holes punched around the periphery of the board eliminates parasitic radiation from the board edges also distorting antenna pattern. ZigBit Amp module should not be placed next to consumer electronics which might interfere with ZigBit Amp's RF frequency band. The board design should prevent propagation of microwave field inside the board material. Electromagnetic waves of high frequency may penetrate the board thus making the edges of the board radiate, which may distort the antenna pattern. To eliminate this effect, metalized and grounded holes must be placed around the board's edges. ZigBit™ 2.4 GHz Amplified Wireless Modules 3-15 8228B–MCU Wireless–06/09 Section 4 Ordering Information 4.1 Ordering Information Part Number ATZB-A24-UFLR ATZB-A24-U0R Note: Description 2.4 GHz IEEE802.15.4/ZigBee Power Amplified OEM Module with U.FL Antenna Connector 2.4 GHz IEEE802.15.4/ZigBee Power Amplified OEM Module with Unbalanced RF output Tape&Reel quantity: 200 ZigBit™ 2.4 GHz Amplified Wireless Modules 4-16 8228B–MCU Wireless–06/09 Headquarters International Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Unit 1-5 & 16, 19/F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon Hong Kong Tel: (852) 2245-6100 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Technical Support [email protected] Sales Contact www.atmel.com/contacts Product Contact Web Site www.atmel.com Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2009 Atmel Corporation. All rights reserved. Atmel ®, Atmel logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 8228B–MCU Wireless–06/09