PRODUCT DATASHEET Ronda series last update 21/7/2016 DETAILS Product Number FCN15209_RONDA-WAS Family Ronda Type Assembly Color white Diameter 69,9 mm Height 25,42 mm Style round Optic Material Holder Material Fastening snaps, socket, clips, screw Status production ready ROHS Comliant Yes Date Updated 21/07/2016 OPTICAL PROPERTIES Viewing Light Effi- LED Angle Beam ciency V10 Gen6 sim: AsymmetricAsymmetric sim: 84 % sim: 1.050 LEDiL: LEDiL CXA/B 15xx Asymmetric degAsymmetric 91 % cd/lm 0.950 Connector LEDiL: LEDiL CXA/B 1816 & CXA/B 1820 & CXA 1850 sim: AsymmetricAsymmetric sim: 86 % sim: 0.900 LEDiL: LEDiL CXA/B 1830 sim: AsymmetricAsymmetric sim: 85 % sim: 0.860 LEDiL: LEDiL Soleriq S13 sim: AsymmetricAsymmetric sim: 82 % sim: 0.750 LEDiL: LEDiL May 30th 2017 4:37 Copyright Ledil Oy - Subject to change without prior notice - Page 1/1 Ledil Oy Salorankatu 10 24240 SALO, Finland http://www.ledil.com email: [email protected] FAX: +358-2-733 8001 A B C D E F G H 4 4 Front plate examples Examples 3 D=49.9 Optic D=69.9mm 2 Ledil-clamp / TE / Bender-wirth / other twist and lock socket types (holder A) 3 Rotation fix Horizontal fix: M3 Nut + bolt Vertical fix: M3 Screw / Twist and lock / Snap 2 BJB and Stucchi 50mm (holder B) LES size up to ~14mm, see compatibility www.ledil.com Tolerances if not otherwise shown According to DIN ISO 2768-1 Linear measures: up to 30mm class M, otherwise class C According to DIN ISO 2768-2 Form and position: class L THIRD ANGLE PROJECTION: 1 This drawing is the property of LEDiL Oy. It may not be reproduced, copied or communicated without a written agreement with LEDiL Oy. See more details on page 2 and 3 H G Ledil Oy Salorankatu 10 FIN 24240 SALO Finland DRAWING TITLE RONDA-family SIZE A3 SCALE 1 PART NUMBER 1:1 WEIGHT - B SHEET A 1/3 A B C D E F G H A 4 3.5 6 4 ( 64.1 ) Front panel location suggestion when seamless look needed Bottom view Nut slot Isometric view 14.6 4 3 7.7 59.3 3 2.2 ronda-was Detail A 12.7 11.2 Front view 45 53. c ti 49 .9 2 61 ( Socket op 2 2.4 * 8.9 .8 .9 69 er d l ho ) 3 3.2 Top view * Ensure from 3d according specific optic version Tolerances if not otherwise shown According to DIN ISO 2768-1 Linear measures: up to 30mm class M, otherwise class C According to DIN ISO 2768-2 Form and position: class L THIRD ANGLE PROJECTION: 1 3. 2 3 . 2 This drawing is the property of LEDiL Oy. It may not be reproduced, copied or communicated without a written agreement with LEDiL Oy. Ledil Oy Salorankatu 10 FIN 24240 SALO Finland DRAWING TITLE RONDA-family SIZE A3 SCALE H G 1 PART NUMBER 1:1 WEIGHT - B SHEET A 2/3 A B C D E F G H 4 OPTIC/HOLDER ASSEMBLY TYPICAL CONNECTOR ASSEMBLY (including solderless BENDER WIRTH as example) 1. Place pin on the side of the lens into relative hole on the holder. B Holder hole 4 3 1. Ensure correct relation of clamp and connector before screwing. Recommended torque 0.6Nm. 3. Attach optic by aligning the holes in the holder with hooks and turning the optic holder clockwise until it locks. 2. Press the lens under clips on the holder, ensuring both clips are fixed. Bender&Wirth model 4xx Typ L1 Clip Pin Align clamp positioning pin with holes in the connector. 2 Clip Tolerances if not otherwise shown According to DIN ISO 2768-1 Linear measures: up to 30mm class M, otherwise class C According to DIN ISO 2768-2 Form and position: class L THIRD ANGLE PROJECTION: 1 This drawing is the property of LEDiL Oy. It may not be reproduced, copied or communicated without a written agreement with LEDiL Oy. G 2 Ledil Oy Salorankatu 10 FIN 24240 SALO Finland DRAWING TITLE RONDA-family SIZE 1 PART NUMBER A3 SCALE H 3 2. Assemble LED, BENDER&WIRTH connector and C13658_CLAMP-VERO13-18 clamp on heatsink with M3 screw. Pin DET B 1:1 WEIGHT - B SHEET A 3/3 NOTE: The typical divergence will be changed by different color, chip size and chip position tolerance. The typical total divergence is the full angle measured where the luminous intensity is half of the peak value. GENERAL INFORMATION - Product series especially designed & optimized for series of LEDs. - Special care taken to make light distribution as uniform as possible. Note! Due to use of high power COB's with this product, special attention to proper thermal design is highly recommended. LEDiL has no liability for direct, indirect or consecutive damages arising from the LEDiL products being used outside of the recommended temperature range.