ES2AW THRU ES2JW SURFACE MOUNT SUPER FAST RECTIFIER Reverse Voltage - 50 to 600 Volts SOD-123FL FEATURES Glass passivated device Ideal for surface mouted applications Low reverse leakage Metallurgically bonded construction High temperature soldering guaranteed: 250 C/10 seconds,0.375”(9.5mm) lead length, 5 lbs. (2.3kg) tension 1.8± 0.1 １．０±0.2 Cathode Band Top View 0.10-0.30 2.8±0.1 1.1± 0.15 Forward Current - 2.0 Ampere 0.6±0.25 MECHANICAL DATA Case: JEDEC SOD-123FL molded plastic body over passivated chip Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight:0.0007 ounce, 0.02 grams 3.7±0.2 Dimensions in millimeters MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%. SYMBOLS MDD Catalog Number Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at Ta=65°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at2.0A Maximum DC reverse current TA=25 C at rated DC blocking voltage TA=100 C Maximum reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range VRRM VRMS VDC ES2BW ES2CW ES2DW ES2EW ES2GW ES2JW 2E1 2E2 2E3 2E4 2E5 2E6 2E8 50 35 50 100 70 100 150 105 150 200 140 200 300 210 300 400 280 400 600 420 600 ES2AW UNITS VOLTS VOLTS VOLTS I(AV) 2.0 Amp IFSM 50.0 Amps VF 1.25 0.95 1.7 Volts IR 5.0 100.0 µA trr 35 ns CJ 25 RθJA TJ,TSTG 90 -55 to +150 pF °C/W C Note: 1.Measured with IF=0.5A, IR=1A, Irr=0.25A. 2.Measured at 1MHz and applied reverse voltage of 4.0V D.C. 3.PCB mounted on 0.2*0.2" (5.0*5.0mm) coppeer pad area. RATINGS AND CHARACTERISTIC CURVES ES2AW THRU ES2JW Fig.1 Reverse Recovery Time Characteristic And Test Circuit Diagram 10 ohm Noninductive 50 ohm Noninductive t rr +0.5 D.U.T + PULSE GENERATOR Note 2 25Vdc approx 0 - -0.25 1 ohm OSCILLOSCOPE Note 1 NonInductive -1.0 Note：1. Rise Time = 7ns, max. Input Impedance = 1megohm,22pF. 2. Ries Time =10ns, max. Source Impedance = 50 ohms. 10ns/div Set time Base for 10ns/div Fig.3 Typical Reverse Characteristics 2.4 300 2.0 100 I R - Reverse Current ( μ A) Average Forward Current (A) Fig.2 Maximum Average Forward Current Rating 1.6 1.2 0.8 Single phase half wave resistive or inductive P.C.B mounted on 0.5×0.5"(12.7×12.7mm ) pad areas. 0.4 T J =125°C 10 T J =75°C 1.0 T J =25°C 0.1 0.0 25 50 75 100 125 150 175 0 100 Fig.5 Typical Junction Capacitance 10 T J =25°C Junction Capacitance ( pF) Instaneous Forward Current (A) 80 60 % of PIV.VOLTS Fig.4 Typical Forward Characteristics 1.0 ES2AW~ES2DW ES2EW/WS2GW 0.1 ES2JW 0.01 0.001 0 0.5 1.5 1.0 2.0 2.5 30 20 T J =25°C f = 1.0MHz V sig = 50mV p-p 10 0.1 Instaneous Forward Voltage (V) 60 50 40 30 20 8.3 ms Single Half Sine Wave (JEDEC Method) 10 00 1 10 1 10 Reverse Voltage (V) Fig.6 Maximum Non-Repetitive Peak Forward Surage Current Peak Forward Surage Current (A) 40 20 Lead Temperature (°C) 100 Number of Cycles The cruve graph is for reference only, can't be the basis for judgment(曲线图仅供参考)! 100