TI TLE2082MP

TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
D
D
Direct Upgrades to TL05x, TL07x, and
TL08x BiFET Operational Amplifiers
Greater Than 2× Bandwidth (10 MHz) and
3× Slew Rate (45 V/µs) Than TL08x
D
D
On-Chip Offset Voltage Trimming for
Improved DC Performance
Wider Supply Rails Increase Dynamic
Signal Range to ±19 V
description
The TLE208x series of JFET-input operational amplifiers more than double the bandwidth and triple the slew
rate of the TL07x and TL08x families of BiFET operational amplifiers. The TLE208x also have wider
supply-voltage rails, increasing the dynamic-signal range for BiFET circuits to ±19 V. On-chip zener trimming
of offset voltage yields precision grades for greater accuracy in dc-coupled applications. The TLE208x are
pin-compatible with lower performance BiFET operational amplifiers for ease in improving performance in
existing designs.
BiFET operational amplifiers offer the inherently higher input impedance of the JFET-input transistors, without
sacrificing the output drive associated with bipolar amplifiers. This makes these amplifiers better suited for
interfacing with high-impedance sensors or very low level ac signals. They also feature inherently better ac
response than bipolar or CMOS devices having comparable power consumption.
Because BiFET operational amplifiers are designed for use with dual power supplies, care must be taken to
observe common-mode input-voltage limits and output voltage swing when operating from a single supply. DC
biasing of the input signal is required and loads should be terminated to a virtual ground node at mid-supply.
Texas Instruments TLE2426 integrated virtual ground generator is useful when operating BiFET amplifiers from
single supplies.
The TLE208x are fully specified at ±15 V and ±5 V. For operation in low-voltage and/or single-supply systems,
Texas Instruments LinCMOS families of operational amplifiers (TLC- and TLV-prefix) are recommended.
When moving from BiFET to CMOS amplifiers, particular attention should be paid to slew rate and bandwidth
requirements and output loading.
For BiFET circuits requiring low noise and/or tighter dc precision, the TLE207x offer the same ac response as
the TLE208x with more stringent dc and noise specifications.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
LinCMOS is a trademark of Texas Instruments.
Copyright  2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081 AVAILABLE OPTIONS
PACKAGED DEVICES
TA
VIOmax
AT 25°C
0°C to 70°C
3 mV
6 mV
–40°C
40°C to 85°C
3 mV
6 mV
– 55°C to 125°C
3 mV
6 mV
SMALL
OUTLINE
(D)
CHIP
FORM
(Y)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(JG)
PLASTIC
DIP
(P)
TLE2081ACD
TLE2081CD
—
—
TLE2081ACP
TLE2081CP
—
TLE2081Y
TLE2081AID
TLE2081ID
—
—
TLE2081AIP
TLE2081IP
—
TLE2081AMFK
TLE2081MFK
TLE2081AMJG
TLE2081MJG
—
—
—
† The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2081ACDR).
‡ Chip forms are tested at TA = 25°C only.
TLE2082 AVAILABLE OPTIONS
PACKAGED DEVICES
TA
VIOmax
AT 25°C
0°C to 70°C
4 mV
7 mV
– 40°C to 85°C
– 55°C to 125°C
SMALL
OUTLINE
(D)
CHIP FORM
(Y)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(JG)
PLASTIC
DIP
(P)
TLE2082ACD
TLE2082CD
—
—
TLE2082ACP
TLE2082CP
—
4 mV
7 mV
TLE2082AID
TLE2082ID
—
—
TLE2082AIP
TLE2082IP
TLE2082Y
4 mV
7 mV
TLE2082AMD
TLE2082MD
TLE2082AMFK
TLE2082MFK
TLE2082AMJG
TLE2082MJG
TLE2082AMP
TLE2082MP
—
‡ The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2082ACDR).
‡ Chip forms are tested at TA = 25°C only.
TLE2084 AVAILABLE OPTIONS
PACKAGED DEVICES
SMALL
OUTLINE
(DW)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(J)
PLASTIC
DIP
(N)
0°C to 70°C
4 mV
7 mV
TLE2084ACDW
TLE2084CDW
—
—
TLE2084ACN
TLE2084CN
—
TLE2084Y
– 55°C to 125°C
4 mV
7 mV
—
TLE2084AMFK
TLE2084MFK
—
—
TLE2084AMJ
TLE2084MJ
† The DW packages are available taped and reeled. Add R suffix to device type (e.g., TLE2084ACDWR).
‡ Chip forms are tested at TA = 25°C only.
2
CHIP
FORM
(Y)
TA
VIOmax
AT 25°C
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
7
3
6
4
5
NC
1OUT
VCC +
1IN –
1IN +
OUT
OFFSET N2 VCC –
1
8
2
7
3
6
4
5
14
2
13
3
12
4
11
5
10
6
9
7
8
4OUT 1OUT
4IN –
1IN –
4IN +
1IN +
VCC – VCC +
3IN +
2IN +
3IN –
2IN –
3OUT 2OUT
NC
TLE2082
FK PACKAGE
(TOP VIEW)
17
6
16
7
15
8
14
9 10 11 12 13
NC
VCC +
NC
OUT
NC
NC
1IN –
NC
1IN+
NC
4
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
4OUT
4IN –
4IN +
VCC –
3IN +
3IN –
3OUT
NC
TLE2084
FK PACKAGE
(TOP VIEW)
NC
2OUT
NC
2IN –
NC
NC
VCC –
NC
2IN +
NC
NC
OFFSET N1
NC
NC
NC
3 2 1 20 19
18
4
5
1
1IN+
NC
VCC+
NC
2IN+
4
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
4IN +
NC
VCC –
NC
3IN +
NC
V CC –
NC
OFFSET N2
NC
NC
IN –
NC
IN +
NC
1OUT
1IN –
1IN +
VCC +
2IN +
2IN –
2OUT
NC
1OUT
NC
V CC +
NC
TLE2081
FK PACKAGE
(TOP VIEW)
VCC+
2OUT
2IN –
2IN+
NC
3OUT
3IN –
8
2
TLE2084
DW PACKAGE
(TOP VIEW)
1IN –
1OUT
NC
4OUT
4IN –
1
TLE2084
J OR N PACKAGE
(TOP VIEW)
2OUT
OFFSET N1
IN –
IN +
VCC –
TLE2082
D, JG, OR P PACKAGE
(TOP VIEW)
2 IN –
TLE2081
D, JG, OR P PACKAGE
(TOP VIEW)
NC – No internal connection
symbol
IN +
+
IN –
–
OUT
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081Y chip information
This chip, when properly assembled, displays characteristics similar to the TLE2081. Thermal compression or
ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive
epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
(1)
(8)
(1)
VCC+
(7)
OFFSET N1
IN +
(3)
(2)
IN –
+
(6)
OUT
–
(5)
OFFSET N2
(4)
VCC –
(2)
85
(7)
(3)
CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
TJmax = 150°C
TOLERANCES ARE ± 10%.
(4)
ALL DIMENSIONS ARE IN MILS.
(5)
(6)
58
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PIN (4) IS INTERNALLY CONNECTED
TO BACKSIDE OF THE CHIP.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082Y chip information
This chip, when properly assembled, displays characteristics similar to the TLE2082. Thermal compression or
ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive
epoxy or a gold-silicon preform.
VCC+
(8)
BONDING PAD ASSIGNMENTS
(8)
(1)
(7)
1IN +
(3)
(2)
1IN –
2OUT
(7)
+
(1)
1OUT
–
+
–
(5)
2IN +
(6)
2IN –
(4)
VCC–
90
(6)
(2)
CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
TJmax = 150°C
TOLERANCES ARE ± 10%.
ALL DIMENSIONS ARE IN MILS.
(3)
(5)
(4)
PIN (4) IS INTERNALLY CONNECTED
TO BACKSIDE OF THE CHIP.
80
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2084Y chip information
This chip, when properly assembled, displays characteristics similar to the TLE2084. Thermal compression or
ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive
epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
(2)
(1)
(14)
(13)
1IN +
(3)
(2)
1IN –
(12)
(3)
2OUT
3IN +
+
(10)
3IN –
(14)
(1)
1OUT
–
+
(7)
(9)
4OUT
VCC+
(4)
–
+
(5)
(6)
2IN +
2IN –
(8)
3OUT
–
+
–
(12)
(13)
4IN +
4IN –
(11)
150
(4)
VCC –
(11)
CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
(10)
(5)
TJmax = 150°C
TOLERANCES ARE ± 10%.
ALL DIMENSIONS ARE IN MILS.
(6)
(7)
(8)
(9)
100
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PIN (11) IS INTERNALLY CONNECTED
TO BACKSIDE OF THE CHIP.
equivalent schematic (each channel)
VCC +
R1
Q1
R2
Q11
Q3
R11
R6
Q17
Q23
Q8
D2
R3
C1
IN –
Q28
Q20
Q13
Q24
D3
Q12
Q4
Q15
R13
Q19
OUT
R12
Q30
Q9
Q16
R8
Q25
C6
Q5
C3
Q29
Q18
Q2
D1
Q6
Q14
Q21
Q22
Q26 Q27
Q10
R5
R9
C4
Q31
R10
C2
OFFSET N1
(see Note A)
OFFSET N2
(see Note A)
VCC –
NOTE A: OFFSET N1 and OFFSET N2 are only availiable on the TLE2081x devices.
ACTUAL DEVICE COMPONENT COUNT
TLE2081
TLE2082
TLE2084
Transistors
COMPONENT
33
57
114
Resistors
25
37
74
Diodes
8
5
10
Capacitors
6
11
22
R14
7
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
C5
R7
R4
Q7
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IN +
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 V
Supply voltage, VCC – (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 19 V
Differential input voltage range, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC + to VCC –
Input voltage range, VI (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC + to VCC –
Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 1 mA
Output current, IO (each output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 80 mA
Total current into VCC + . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 mA
Total current out of VCC – . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 mA
Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: DW or N package . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J package . . . . . . . . . . . . . . . . . . . . . 300°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC + and VCC – .
2. Differential voltages are at IN+ with respect to IN –.
3. The output can be shorted to either supply. Temperatures and/or supply voltages must be limited to ensure that the maximum
dissipation rate is not exceeded.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
TA = 125°C
POWER RATING
D
725 mW
5.8 mW/°C
464 mW
377 mW
145 mW
DW
1025 mW
8.2 mW/°C
656 mW
533 mW
205 mW
FK
1375 mW
11.0 mW/°C
880 mW
715 mW
275 mW
275 mW
J
1375 mW
11.0 mW/°C
880 mW
715 mW
JG
1050 mW
8.4 mW/°C
672 mW
546 mW
210 mW
N
1150 mW
9.2 mW/°C
736 mW
598 mW
230 mW
P
1000 mW
8.0 mW/°C
640 mW
344 mW
200 mW
recommended operating conditions
Supply voltage, VCC±
Common mode input voltage,
Common-mode
voltage VIC
VCC ± = ± 5 V
VCC ± = ±15 V
Operating free-air temperature, TA
8
POST OFFICE BOX 655303
C SUFFIX
I SUFFIX
M SUFFIX
MIN
MAX
MIN
MAX
MIN
MAX
± 2.25
± 19
± 2.25
± 19
± 2.25
± 19
– 0.9
5
– 0.8
5
– 0.8
5
– 10.9
15
– 10.8
15
– 10.8
15
0
70
– 40
85
– 55
125
• DALLAS, TEXAS 75265
UNIT
V
V
°C
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081C electrical characteristics at specified free-air temperature, VCC± = ±5 V (unless
otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
Input bias current
TEST CONDITIONS
TA†
25°C
VIC = 0,
RS = 50 Ω
VO = 0,
25°C
VO = 0,,
Common-mode input
voltage range
RS = 50 Ω
IO = – 2 mA
IO = 200 µA
VOM –
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 2
2.3
3V
RL = 2 kΩ
RL = 10 kΩ
ri
Input resistance
TYP
MAX
0.3
3
5
3.2
29
3.2
29
5
100
5
100
15
1.4
175
15
5
5
to
–1
5
to
– 1.9
5
to
– 0.9
25°C
3.8
Full range
3.7
25°C
3.5
Full range
3.4
25°C
1.5
Full range
MIN
1.4
25°C
IO = – 20 mA
Maximum negative
peak
g
output voltage swing
6
Full range
IO = – 200 µA
Maximum positive peak
output voltage swing
0.34
Full range
Full range
g
VOM +
MAX
8
Full range
VIC = 0,,
See Figure 4
TLE2081AC
TYP
Full range
25°C
VICR
TLE2081C
MIN
– 3.5
Full range
– 3.4
25°C
– 3.7
Full range
– 3.6
25°C
– 1.5
Full range
– 1.5
25°C
80
Full range
79
25°C
90
Full range
89
25°C
95
Full range
94
5
5
to
–1
5
to
– 1.9
4.1
3.8
3.9
3.5
3.9
3.4
2.3
1.5
– 4.2
– 3.5
– 3.4
– 4.1
– 3.7
– 4.1
– 3.6
– 2.4
– 1.5
– 2.4
91
80
91
79
100
90
100
89
106
95
106
Differential
25°C
2.5
2.5
25°C
80
80
CMRR
Common-mode
rejection ratio
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
25°C
70
Full range
68
kSVR
Supply-voltage
y
g rejection
j
ratio(∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,
VO = 0,
RS = 50 Ω
25°C
82
Full range
80
dB
94
11
f = 1 MHz
V
– 1.5
11
Open-loop output
impedance
V
– 4.2
25°C
zo
V
1.5
Common mode
VIC = 0,,
See Figure 5
nA
2.3
1012
Input capacitance
nA
4.1
1012
ci
µV/°C
3.7
25°C
VIC = 0
mV
5
to
– 0.9
1.5
25°C
175
UNIT
89
70
89
68
99
82
80
99
Ω
pF
Ω
dB
dB
† Full range is 0°C to 70°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081C electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless
otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
ICC
Supply current
VO = 0
0,
IOS
Short-circuit output
current
VO = 0
No load
TLE2081C
MIN
TYP
MAX
MIN
TYP
MAX
25°C
1.35
1.6
2.2
1.35
1.6
2.2
Full range
VID = 1 V
VID = – 1 V
TLE2081AC
TA†
2.2
25°C
2.2
– 35
– 35
45
45
UNIT
mA
mA
† Full range is 0°C to 70°C.
TLE2081C operating characteristics at specified free-air temperature, VCC± = ±5 V
PARAMETER
TA†
TEST CONDITIONS
TLE2081C
MIN
TYP
25°C
SR +
SR –
ts
Vn
VN(PP)
Positive slew rate
Negative slew rate
Settling time
VO(PP) = ± 2.3 V,
AVD = – 1,
1
RL = 2 kΩ,
kΩ
CL = 100 pF,
F, See Figure 1
AVD = – 1,
2-V step,,
RL = 1 kΩ,
CL = 100 pF
23
MIN
TYP
38
23
38
V/µs
23
0.25
0.25
0.4
0.4
µs
To 1 mV
25°C
f = 10 Hz to
10 kHz
f = 0.1 Hz to
10 Hz
UNIT
V/µs
25°C
f = 10 kHz
MAX
35
23
To 10 mV
f = 10 Hz
RS = 20 Ω,
See Figure 3
MAX
35
25°C
Full
range
Equivalent
q
input noise
voltage
Peak-to-peak equivalent
q
input noise voltage
Full
range
TLE2081AC
28
28
11.6
11.6
6
6
0.6
0.6
nV/ √Hz
µV
25°C
In
Equivalent input noise
current
VIC = 0,
f = 10 kHz
25°C
2.8
2.8
THD + N
Total harmonic distortion
plus noise
VO(PP) = 5 V, AVD = 10,
f = 1 kHz
kHz,
RL = 2 kΩ
kΩ,
RS = 25 Ω
25°C
0 013%
0.013%
0 013%
0.013%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
25°C
94
9.4
94
9.4
MHz
BOM
Maximum output-swing
g
bandwidth
VO(PP) = 4 V,, AVD = – 1,,
RL = 2 kΩ ,
CL = 25 pF
25°C
28
2.8
28
2.8
MHz
φm
Phase margin at unity gain
VI = 10 mV,,
CL = 25 pF,
25°C
56°
56°
RL = 2 kΩ,,
See Figure 2
RL = 2 kΩ,,
See Figure 2
† Full range is 0°C to 70°C.
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
fA/ √Hz
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless
otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
Input bias current
TA†
TEST CONDITIONS
25°C
VIC = 0,
RS = 50 Ω
VO = 0,
25°C
VO = 0,,
Common-mode input
voltage range
RS = 50 Ω
IO = – 2 mA
IO = 200 µA
VOM –
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 10 V
RL = 2 kΩ
RL = 10 kΩ
ri
ci
Input resistance
Input capacitance
MAX
0.47
3
5
29
3.2
29
6
100
6
100
1.4
175
20
5
15
to
– 11
15
to
– 11.9
15
to
– 10.9
25°C
13.8
13.7
25°C
13.5
Full range
13.4
25°C
11.5
– 13.8
Full range
– 13.7
25°C
– 13.5
Full range
– 13.4
25°C
– 11.5
Full range
– 11.5
25°C
80
Full range
79
25°C
90
Full range
89
25°C
95
Full range
94
5
15
to
– 11
15
to
– 11.9
14.1
13.8
13.9
13.5
13.9
13.4
12.3
11.5
– 14.2
– 13.8
–13.5
– 14
– 13.4
– 12.4
– 11.5
– 12.4
96
80
96
79
109
90
109
89
118
95
118
25°C
2.5
2.5
25°C
80
80
kSVR
Supply-voltage
y
g rejection
j
ratio (∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,
VO = 0,
RS = 50 Ω
80
79
25°C
82
Full range
80
dB
94
Differential
25°C
V
– 11.5
7.5
Full range
V
– 13.7
– 14
7.5
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
V
– 14.2
25°C
Common-mode
rejection ratio
nA
11.5
Common
mode
CMRR
nA
12.3
1012
f = 1 MHz
µV/°C
14.1
1012
Open-loop output
impedance
mV
13.7
25°C
zo
175
UNIT
15
to
– 10.9
11.5
25°C
VIC = 0
VIC = 0,
See Figure 5
TYP
3.2
20
Full range
Full range
MIN
1.4
25°C
IO = – 20 mA
Maximum negative
peak
g
output voltage swing
6
Full range
IO = – 200 µA
Maximum positive peak
output voltage swing
0.49
Full range
Full range
g
VOM +
MAX
8
Full range
VIC = 0,,
See Figure 4
TLE2081AC
TYP
Full range
25°C
VICR
TLE2081C
MIN
98
80
98
79
99
82
81
99
Ω
pF
Ω
dB
dB
† Full range is 0°C to 70°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081C electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
ICC
Supply current
VO = 0
0,
No load
IOS
Short-circuit output
current
VO = 0
VID = 1 V
VID = – 1 V
TLE2081C
TLE2081AC
TA†
MIN
TYP
MAX
MIN
TYP
MAX
25°C
1.35
1.7
2.2
1.35
1.7
2.2
Full range
2.2
2.2
– 30
– 45
– 30
– 45
30
48
30
48
25°C
UNIT
mA
mA
† Full range is 0°C to 70°C.
TLE2081C operating characteristics at specified free-air temperature, VCC± = ±15 V
PARAMETER
SR +
TEST CONDITIONS
Positive slew rate
VO(PP) = 10 V, AVD = – 1,
RL = 2 kΩ
kΩ,
CL = 100 pF
pF,
See Figure 1
SR –
ts
Negative slew rate
Settling time
Vn
Equivalent
q
input noise
voltage
VN(PP)
Peak-to-peak
equivalent input noise
voltage
AVD = – 1,
10-V step,,
RL = 1 kΩ,
CL = 100 pF
MIN
TYP
25°C
30
40
Full
range
27
25°C
30
Full
range
27
To 10 mV
TLE2081AC
MAX
MIN
TYP
30
40
45
30
f = 10 Hz to
10 kHz
f = 0.1 Hz to
10 Hz
UNIT
45
V/µs
27
0.4
0.4
1.5
1.5
µs
To 1 mV
f = 10 kHz
MAX
V/µs
27
25°C
f = 10 Hz
RS = 20 Ω,
See Figure 3
TLE2081C
TA†
25°C
28
28
11.6
11.6
6
6
0.6
0.6
nV√Hz
µV
25°C
In
Equivalent
input noise
q
current
0
VIC = 0,
f = 10 kHz
25°C
28
2.8
28
2.8
THD + N
Total harmonic
distortion plus noise
VO(PP) = 20 V, AVD = 10,
f = 1 kHz
kHz,
RL = 2 kΩ
kΩ,
RS = 25 Ω
25°C
0 008%
0.008%
0 008%
0.008%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
25°C
8
10
8
10
MHz
BOM
Maximum outputswing bandwidth
VO(PP) = 20 V,, AVD = – 1,,
RL = 2 kΩ,
CL = 25 pF
25°C
478
637
478
637
kHz
φm
Phase margin
g at unity
y
gain
VI = 10 mV,
CL = 25 pF,
25°C
RL = 2 kΩ,,
See Figure 2
RL = 2 kΩ,
See Figure 2
57°
† Full range is 0°C to 70°C.
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
57°
fA /√Hz
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081I electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise
noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
TA†
TEST CONDITIONS
25°C
VIC = 0,
RS = 50 Ω,
VO = 0,
VO = 0,,
Maximum positive peak
VOM +
output voltage swing
IO = – 2 mA
IO = – 20 mA
IO = 200 µA
VOM –
Maximum negative
peak
g
output voltage swing
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 2
2.3
3 V RL = 2 kΩ
RL = 10 kΩ
ri
ci
Input resistance
Input capacitance
3.8
3.7
25°C
3.5
Full range
3.4
25°C
1.5
– 3.8
Full range
– 3.7
25°C
– 3.5
Full range
– 3.4
25°C
– 1.5
Full range
– 1.5
25°C
80
Full range
79
25°C
90
Full range
89
25°C
95
Full range
94
µV/°C
5
100
5
100
pA
5
nA
15
175
15
175
pA
10
nA
5
to
– 1.9
5
to
–1
5
to
– 1.9
4.1
3.8
4.1
3.7
3.9
3.5
3.9
3.4
2.3
1.5
– 4.2
– 3.8
1.5
– 4.2
– 3.7
– 4.1
– 3.5
– 4.1
– 3.4
– 2.4
– 1.5
– 2.4
91
80
91
79
100
90
100
89
106
95
106
25°C
11
11
Differential
25°C
2.5
2.5
25°C
80
80
Common-mode
rejection ratio
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
kSVR
Supply-voltage
y
g rejection
j
ratio (∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,,
VO = 0,
RS = 50 Ω
25°C
70
Full range
68
25°C
82
Full range
80
dB
94
Common
mode
CMRR
V
– 1.5
1012
f = 1 MHz
V
2.3
1012
Open-loop output
impedance
V
5
to
– 0.8
25°C
zo
mV
29
1.5
25°C
UNIT
3.2
5
to
– 0.8
25°C
VIC = 0
VIC = 0,
See Figure 5
5
to
–1
3
5.6
10
Full range
Full range
0.3
MAX
29
Full range
IO = – 200 µA
6
TYP
5
25°C
Full range
g
MIN
3.2
Full range
RS = 50 Ω
TLE2081AI
MAX
7.6
Full range
Input bias current
Common-mode input
voltage range
0.34
25°C
VIC = 0,,
See Figure 4
TYP
Full range
25°C
VICR
TLE2081I
MIN
89
70
89
68
99
82
80
99
Ω
pF
Ω
dB
dB
† Full range is – 40°C to 85°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081I electrical characteristics at specified free-air temperature, VCC± = ±5 V (unless otherwise
noted) (continued)
PARAMETER
TEST CONDITIONS
ICC
Supply current
VO = 0
0,
No load
IOS
Short-circuit output
current
VO = 0
VID = 1 V
VID = – 1 V
TLE2081I
TLE2081AI
TA†
MIN
TYP
MAX
MIN
TYP
MAX
25°C
1.35
1.6
2.2
1.35
1.6
2.2
Full range
2.2
25°C
2.2
– 35
– 35
45
45
UNIT
mA
mA
† Full range is – 40°C to 85°C.
TLE2081I operating characteristics at specified free-air temperature, VCC± = ±5 V
PARAMETER
TEST CONDITIONS
TA†
TLE2081I
MIN
TYP
25°C
SR +
SR –
ts
Positive slew rate
Negative slew rate
Settling time
Vn
Equivalent
q
input noise
voltage
VN(PP)
Peak-to-peak equivalent
q
input noise voltage
VO(PP) = ± 2.3 V,
AVD = – 1
1,
RL = 2 kΩ
kΩ,
CL = 100 pF,
F, See Figure 1
Full
range
AVD = – 1,
2-V step,,
RL = 1 kΩ,
CL = 100 pF
22
MIN
TYP
38
22
38
V/µs
22
0.25
0.25
0.4
0.4
µs
To 1 mV
f = 10 Hz to
10 kHz
UNIT
V/µs
25°C
f = 10 kHz
MAX
35
22
To 10 mV
f = 10 Hz
RS = 20 Ω,
See Figure 3
MAX
35
25°C
Full
range
TLE2081AI
25°C
28
28
11.6
11.6
6
6
06
0.6
06
0.6
nV/√Hz
µV
25°C
f = 0.1 Hz to
10 Hz
In
Equivalent input noise
current
VIC = 0,
f = 10 kHz
25°C
2.8
2.8
THD + N
Total harmonic distortion
plus noise
VO(PP) = 5 V, AVD = 10,
f = 1 kHz
kHz,
RL = 2 kΩ
kΩ,
RS = 25 Ω
25°C
0 013%
0.013%
0 013%
0.013%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
25°C
94
9.4
94
9.4
MHz
BOM
Maximum output-swing
g
bandwidth
VO(PP) = 4 V,, AVD = – 1,,
RL = 2 kΩ ,
CL = 25 pF
25°C
28
2.8
28
2.8
MHz
φm
Phase margin at unity gain
VI = 10 mV,,
CL = 25 pF,
25°C
56°
56°
RL = 2 kΩ,,
See Figure 2
RL = 2 kΩ,,
See Figure 2
† Full range is – 40°C to 85°C.
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
fA/√Hz
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081I electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless
otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
TA†
TEST CONDITIONS
VO = 0,
VO = 0,,
IO = – 2 mA
IO = – 20 mA
IO = 200 µA
VOM –
Maximum negative
peak
g
output voltage swing
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 10 V
RL = 2 kΩ
RL = 10 kΩ
ri
ci
Input resistance
Input capacitance
13.8
13.7
25°C
13.5
Full range
13.4
25°C
11.5
– 13.8
Full range
– 13.7
25°C
– 13.5
Full range
– 13.4
25°C
– 11.5
Full range
– 11.5
25°C
80
Full range
79
25°C
90
Full range
89
25°C
95
Full range
94
6
100
6
100
pA
5
nA
20
175
20
175
pA
10
nA
15
to
– 11.9
15
to
– 11
15
to
– 11.9
14.1
13.8
14.1
13.7
13.9
13.5
13.9
13.4
12.3
11.5
– 14.2
– 13.8
11.5
– 14.2
– 13.7
– 14
–13.5
– 14
– 13.4
– 12.4
– 11.5
– 12.4
96
80
96
79
109
90
109
89
118
95
118
7.5
7.5
Differential
25°C
2.5
2.5
80
80
Common-mode
rejection ratio
VIC = VICRmin,
VO = 0
0,
RS = 50 Ω
25°C
80
Full range
79
Supply-voltage
y
g rejection
j
ratio (∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,,
VO = 0,
RS = 50 Ω
25°C
82
Full range
80
dB
94
25°C
CMRR
V
– 11.5
Common
mode
25°C
V
12.3
1012
f = 1 MHz
V
15
to
– 10.8
1012
Open-loop output
impedance
kSVR
µV/°C
25°C
zo
mV
29
11.5
25°C
UNIT
3.2
15
to
– 10.8
25°C
VIC = 0
VIC = 0,
See Figure 5
15
to
– 11
3
5.6
10
Full range
Full range
0.47
MAX
29
Full range
IO = – 200 µA
6
TYP
5
25°C
Full range
g
MIN
3.2
Full range
RS = 50 Ω
TLE2081AI
MAX
7.6
Full range
Input bias current
Maximum positive peak
VOM +
output voltage swing
0.49
Full range
25°C
VIC = 0,,
See Figure 4
Common-mode input
voltage range
TYP
25°C
VIC = 0,
RS = 50 Ω,
25°C
VICR
TLE2081I
MIN
98
80
Ω
pF
Ω
98
dB
79
99
82
80
99
dB
† Full range is – 40°C to 85°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081I electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
ICC
Supply current
VO = 0
0,
No load
IOS
Short-circuit output
current
VO = 0
VID = 1 V
VID = – 1 V
TLE2081I
TLE2081AI
TA†
MIN
TYP
MAX
MIN
TYP
MAX
25°C
1.35
1.7
2.2
1.35
1.7
2.2
Full range
25°C
2.2
2.2
– 30
– 45
– 30
– 45
30
48
30
48
UNIT
mA
mA
† Full range is – 40°C to 85°C.
TLE2081I operating characteristics at specified free-air temperature, VCC± = ±15 V
PARAMETER
SR +
Positive slew rate
SR –
Negative slew rate
ts
Settling time
Vn
Equivalent
input noise
q
voltage
VN(PP)
Peak-to-peak equivalent
input noise voltage
In
Equivalent input noise
current
THD + N
Total harmonic distortion
plus noise
B1
Unity gain bandwidth
Unity-gain
BOM
Maximum output-swing
g
bandwidth
φm
Phase margin at unity gain
TEST CONDITIONS
VO(PP) = ± 10 V,
AVD = – 1
1,
RL = 2 kΩ
kΩ,
CL = 100 pF,
F,
See Figure 1
AVD = – 1,
10-V step,
RL = 1 kΩ,
CL = 100 pF
MIN
TYP
25°C
30
40
Full
range
24
25°C
30
Full
range
24
45
MIN
TYP
30
40
30
V/µs
0.4
0.4
1.5
1.5
µs
To 1 mV
25°C
f = 10 Hz to
10 kHz
f = 0.1 Hz to
10 Hz
28
28
11.6
11.6
6
6
0.6
0.6
nV/√Hz
µV
25°C
VIC = 0,
f = 10 kHz
25°C
2.8
2.8
VO(PP) = 20 V,
f = 1 kHz
kHz,
RS = 25 Ω
VI = 10 mV,
CL = 25 pF,
AVD = 10,
RL = 2 kΩ
kΩ,
25°C
0 008%
0.008%
0 008%
0.008%
RL = 2 kΩ,
See Figure 2
UNIT
45
25°C
f = 10 kHz
MAX
V/µs
24
fA/√Hz
25°C
8
10
8
10
MHz
VO(PP) = 20 V, AVD = – 1,
RL = 2 kΩ,
CL = 25 pF
25°C
478
637
478
637
kHz
VI = 10 mV,
CL = 25 pF,
25°C
RL = 2 kΩ,
See Figure 2
† Full range is – 40°C to 85°C.
16
TLE2081AI
MAX
24
To 10 mV
f = 10 Hz
RS = 20 Ω,
See Figure 3
TLE2081I
TA†
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
57°
57°
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless
otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient of
input offset voltage
IIO
Input offset current
IIB
TA†
TEST CONDITIONS
VO = 0,
VO = 0,,
Maximum positive peak
output voltage swing
IO = – 2 mA
IO = – 20 mA
IO = 200 µA
VOM –
Maximum negative
peak
g
output voltage swing
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 2.3
23V
RL = 2 kΩ
RL = 10 kΩ
ri
ci
Input resistance
Input capacitance
3.8
3.6
25°C
3.5
Full range
3.3
25°C
1.5
5
100
5
100
pA
20
nA
15
175
15
175
pA
65
nA
– 3.8
Full range
– 3.6
25°C
– 3.5
Full range
– 3.3
25°C
– 1.5
Full range
– 1.4
25°C
80
Full range
78
25°C
90
Full range
88
25°C
95
Full range
93
5
to
–1
5
to
– 1.9
4.1
3.8
4.1
3.6
3.9
3.5
3.9
3.3
2.3
1.5
– 4.2
– 3.8
1.4
– 4.2
– 3.6
– 4.1
– 3.5
– 4.1
– 3.3
– 2.4
– 1.5
– 2.4
91
80
91
78
100
90
100
88
106
95
106
25°C
11
11
Differential
25°C
2.5
2.5
25°C
80
80
CMRR
Common-mode
rejection ratio
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
kSVR
Supply-voltage
y
g rejection
j
ratio (∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,
VO = 0,
RS = 50 Ω
25°C
70
Full range
68
25°C
82
Full range
80
dB
93
Common
mode
f = 1 MHz
V
– 1.4
1012
Open-loop output
impedance
V
2.3
1012
zo
V
5
to
– 0.8
25°C
VIC = 0
VIC = 0,
See Figure 5
5
to
– 1.9
1.4
25°C
mV
µV/°C
5
to
– 0.8
25°C
UNIT
29∗
65
5
to
–1
3
8.2
20
Full range
Full range
0.3
MAX
3.2
Full range
IO = – 200 µA
6
TYP
29∗
Full range
RS = 50 Ω
MIN
3.2
25°C
Input bias current
TLE2081AM
MAX
11.2
25°C
Full range
g
VOM +
0.34
Full range
Full range
VIC = 0,,
See Figure 4
Common-mode input
voltage range
TYP
25°C
VIC = 0,
RS = 50Ω
25°C
VICR
TLE2081M
MIN
89
70
89
68
99
82
80
99
Ω
pF
Ω
dB
dB
∗On products compliant with MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless
otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
ICC
Supply current
VO = 0
0,
No load
IOS
Short-circuit output
current
VO = 0
VID = 1 V
VID = – 1 V
TLE2081M
TLE2081AM
TA†
MIN
TYP
MAX
MIN
TYP
MAX
25°C
1.35
1.6
2.2
1.35
1.6
2.2
Full range
2.2
25°C
2.2
– 35
– 35
45
45
UNIT
mA
mA
† Full range is – 55°C to 125°C.
TLE2081M operating characteristics at specified free-air temperature, VCC ± = ±5 V
PARAMETER
TEST CONDITIONS
TA†
TLE2081M
MIN
TYP
25°C
SR +
SR –
ts
Positive slew rate
Negative slew rate
Settling time
Vn
Equivalent
q
input noise
voltage
VN(PP)
Peak-to-peak
equivalent input noise
voltage
VO(PP) = ± 2.3 V,
AVD = – 1
1,
RL = 2 kΩ
kΩ,
CL = 100 pF,
F,
See Figure 1
Full
range
AVD = – 1,
2-V step,,
RL = 1 kΩ,
CL = 100 pF
20∗
MIN
TYP
38
20∗
38
V/µs
20∗
0.25
0.25
0.4
0.4
µs
To 1 mV
f = 10 Hz to
10 kHz
UNIT
V/µs
25°C
f = 10 kHz
MAX
35
20∗
To 10 mV
f = 10 Hz
RS = 20 Ω,
See Figure 3
MAX
35
25°C
Full
range
TLE2081AM
25°C
28
28
11.6
11.6
6
6
06
0.6
06
0.6
2.8
2.8
nV/√Hz
µV
25°C
f = 0.1 Hz to
10 Hz
In
Equivalent input noise
current
VIC = 0,
f = 10 kHz
25°C
THD + N
Total harmonic
distortion plus noise
VO(PP) = 5 V,
f = 1 kHz
kHz,
RS = 25 Ω
AVD = 10,
RL = 2 kΩ
kΩ,
25°C
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
RL = 2 kΩ,,
See Figure 2
25°C
94
9.4
94
9.4
MHz
BOM
Maximum output-swing
g
bandwidth
VO(PP) = 4 V,,
RL = 2 kΩ ,
AVD = – 1,,
CL = 25 pF
25°C
28
2.8
28
2.8
MHz
φm
Phase margin
g at unity
y
gain
VI = 10 mV,
CL = 25 pF,
RL = 2 kΩ,
See Figure 2
25°C
56°
56°
0 013%
0.013%
∗On products compliant with MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
fA /√Hz
0 013%
0.013%
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081M electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
TA†
TEST CONDITIONS
VO = 0,
VO = 0,,
Maximum positive peak
output voltage swing
IO = – 2 mA
IO = – 20 mA
IO = 200 µA
VOM –
Maximum negative
peak
g
output voltage swing
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 10 V
RL = 2 kΩ
RL = 10 kΩ
ri
ci
Input resistance
Input capacitance
13.8
13.6
25°C
13.5
Full range
13.3
25°C
11.5
6
100
6
100
pA
20
nA
20
175
20
175
pA
65
nA
– 13.8
Full range
– 13.6
25°C
– 13.5
Full range
– 13.3
25°C
– 11.5
Full range
– 11.4
25°C
80
Full range
78
25°C
90
Full range
88
25°C
95
Full range
93
15
to
– 11
15
to
– 11.9
14.1
13.8
14.1
13.6
13.9
13.5
13.9
13.3
12.3
11.5
– 14.2
– 13.8
11.4
– 14.2
– 13.6
– 14
–13.5
– 14
– 13.3
– 12.4
– 11.5
– 12.4
96
80
96
78
109
90
109
88
118
95
118
25°C
7.5
7.5
Differential
25°C
2.5
2.5
25°C
80
80
CMRR
Common-mode
rejection ratio
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
kSVR
Supply-voltage
y
g rejection
j
ratio (∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,
VO = 0,
RS = 50 Ω
25°C
80
Full range
78
25°C
82
Full range
80
dB
93
Common
mode
f = 1 MHz
V
– 11.4
1012
Open-loop output
impedance
V
12.3
1012
zo
V
15
to
– 10.8
25°C
VIC = 0
VIC = 0,
See Figure 5
15
to
– 11.9
11.4
25°C
mV
µV/°C
15
to
– 10.8
25°C
UNIT
29∗
65
15
to
– 11
3
8.2
20
Full range
Full range
0.47
MAX
3.2
Full range
IO = – 200 µA
6
TYP
29∗
Full range
RS = 50 Ω
MIN
3.2
25°C
Input bias current
TLE2081AM
MAX
11.2
25°C
Full range
g
VOM +
0.49
Full range
Full range
VIC = 0,,
See Figure 4
Common-mode input
voltage range
TYP
25°C
VIC = 0,
RS = 50 Ω
25°C
VICR
TLE2081M
MIN
98
80
98
78
99
82
80
99
Ω
pF
Ω
dB
dB
∗On products compliant with MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081M electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)(continued)
PARAMETER
TEST CONDITIONS
ICC
Supply current
VO = 0
0,
No load
IOS
Short-circuit output
current
VO = 0
VID = 1 V
VID = – 1 V
TLE2081M
TLE2081AM
TA†
MIN
TYP
MAX
MIN
TYP
MAX
25°C
1.35
1.7
2.2
1.35
1.7
2.2
Full range
25°C
2.2
2.2
– 30
– 45
– 30
– 45
30
48
30
48
UNIT
mA
mA
† Full range is – 55°C to 125°C.
TLE2081M operating characteristics at specified free-air temperature, VCC ± = ±15 V
PARAMETER
SR +
TEST CONDITIONS
Positive slew rate
SR –
Negative slew rate
ts
Settling time
Vn
Equivalent
q
input noise
voltage
VN(PP)
Peak-to-peak
equivalent input noise
voltage
VO(PP) = 10 V,
AVD = – 1,
1
RL = 2 kΩ,
kΩ
CL = 100 pF,
F,
See Figure 1
AVD = – 1,
10-V step,,
RL = 1 kΩ,
CL = 100 pF
MIN
TYP
25°C
30
40
Full
range
22
25°C
30
Full
range
22
TLE2081AM
MAX
MIN
TYP
30
40
45
30
V/µs
22
0.4
0.4
1.5
1.5
µs
To 1 mV
f = 10 Hz to
10 kHz
25°C
28
28
11.6
11.6
6
6
06
0.6
06
0.6
In
Equivalent input noise
current
f = 10 kHz
25°C
2.8
2.8
THD + N
VO(PP) = 20 V, AVD = 10,
Total harmonic distortion
f = 1 kHz
kHz,
RL = 2 kΩ
kΩ,
plus noise
RS = 25 Ω
25°C
0 008%
0.008%
0 008%
0.008%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
BOM
Maximum output-swing
g
bandwidth
φm
Phase margin
g at unity
y
gain
RL = 2 kΩ,,
See Figure 2
fA/√Hz
25°C
8∗
10
8∗
10
MHz
VO(PP) = 20 V,, AVD = – 1,,
RL = 2 kΩ,
CL = 25 pF
25°C
478∗
637
478∗
637
kHz
VI = 10 mV,
CL = 25 pF,
25°C
RL = 2 kΩ,
See Figure 2
57°
∗On products compliant with MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
20
nV/√Hz
µV
25°C
f = 0.1 Hz to
10 Hz
VIC = 0,
UNIT
45
25°C
f = 10 kHz
MAX
V/µs
22
To 10 mV
f = 10 Hz
RS = 20 Ω,
See Figure 3
TLE2081M
TA†
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
57°
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081Y electrical characteristics at VCC± = ±15 V, TA = 25°C
PARAMETER
VIO
IIO
Input offset voltage
IIB
Input bias current
VICR
Common-mode input voltage
g range
g
RS = 50 Ω
VOM +
Maximum
M
i
positive
iti peak
k
output
out
ut voltage swing
VOM –
AVD
ri
Input offset current
Maximum
M
i
negative
ti peak
k output
t t
voltage swing
L
i
l differential
diff
ti l voltage
lt
Large-signal
am
lification
amplification
Input resistance
TLE2081Y
TEST CONDITIONS
VIC = 0,
VO = 0,
VIC = 0
0,
VO = 0
0,
MIN
RS = 50 Ω
See Figure 4
TYP
0.49
6
6
100
20
175
15
to
– 11
15
to
11.9
IO = – 200 µA
IO = – 2 mA
13.8
14.1
13.5
13.9
IO = – 20 mA
IO = 200 µA
11.5
12.3
– 13.8
– 14.2
IO = 2 mA
IO = 20 mA
VO = ± 10 V
MAX
– 13.5
– 14
– 11.5
– 12.4
RL = 600 Ω
80
96
RL = 2 kΩ
90
109
RL = 10 kΩ
95
118
Common mode
7.5
Differential
2.5
mV
pA
V
V
V
dB
Ω
1012
VIC = 0
UNIT
ci
Input capacitance
VIC = 0
0, See Figure 5
zo
Open-loop output impedance
f = 1 MHz
80
Ω
CMRR
Common-mode rejection ratio
VIC = VICRmin,
VO = 0,
RS = 50 Ω
80
98
dB
kSVR
Supply-voltage rejection ratio
(∆VCC± /∆VIO)
VCC ±= ± 5 V to ±15 V,
VO = 0,
RS = 50 Ω
82
99
dB
ICC
Supply current
VO = 0,
No load
1.35
1.7
– 30
– 45
VO = 0
VID = 1 V
VID = – 1 V
30
48
IOS
Short circuit output current
Short-circuit
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
pF
2.2
mA
mA
21
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082C electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless
otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
TA†
TEST CONDITIONS
25°C
VIC = 0,
RS = 50 Ω
VO = 0,
IO = – 200 µA
VOM +
Maximum positive peak
output voltage swing
IO = – 2 mA
IO = – 20 mA
IO = 200 µA
VOM –
Maximum negative
peak
g
output voltage swing
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 2
2.3
3V
RL = 2 kΩ
RL = 10 kΩ
ri
Input resistance
Common mode
ci
Input
In
ut
capacitance
zo
Open-loop output impedance
Differential
VIC = 0
VIC = 0
0,
See Figure 5
5
to
–1
3.8
3.7
25°C
3.5
Full range
3.4
25°C
1.5
– 3.8
Full range
– 3.7
25°C
– 3.5
Full range
– 3.4
25°C
– 1.5
Full range
– 1.5
25°C
80
Full range
79
25°C
90
Full range
89
25°C
95
Full range
94
5
100
5
100
pA
1.4
nA
15
175
15
175
pA
5
nA
5
to
– 1.9
4.1
3.8
4.1
3.7
3.9
3.5
3.9
2.3
1.5
– 4.2
– 3.8
2.3
1.5
– 4.2
– 3.7
– 4.1
– 3.5
– 4.1
– 2.4
– 1.5
– 2.4
– 1.5
91
80
91
79
100
90
100
106
95
106
94
2.5
2.5
80
Full range
68
kSVR
Supply-voltage
y
g rejection
j
ratio(∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,,
VO = 0,
RS = 50 Ω
25°C
82
Full range
80
ICC
Supply
y current
(both channels)
VO = 0
0,
25°C
2.7
Full range
† Full range is 0°C to 70°C.
• DALLAS, TEXAS 75265
dB
89
25°C
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
V
– 3.4
11
Common mode rejection ratio
Common-mode
V
3.4
11
70
V
5
to
– 0.9
25°C
25°C
POST OFFICE BOX 655303
5
to
–1
1012
25°C
No load
5
to
– 1.9
1012
CMRR
22
µV/°C
25°C
f = 1 MHz
mV
25
1.5
25°C
UNIT
2.3
5
to
– 0.9
25°C
4
5.1
5
Full range
Full range
0.65
MAX
25
Full range
Full range
g
6
TYP
1.4
25°C
RS = 50 Ω
MIN
2.3
Full range
VO = 0,,
TLE2082AC
MAX
8.1
Full range
Input bias current
Common-mode input
voltage range
0.9
25°C
VIC = 0,,
See Figure 4
TYP
Full range
25°C
VICR
TLE2082C
MIN
Ω
pF
Ω
80
89
70
89
dB
68
99
82
99
dB
80
2.9
3.9
3.9
2.7
2.9
3.9
3.9
mA
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082C electrical characteristics at specified free-air temperature, VCC± = ±5 V (unless
otherwise noted) (continued)
PARAMETER
Crosstalk attenuation
IOS
Short circuit output current
Short-circuit
TEST CONDITIONS
VIC = 0,
RL = 2 kΩ
VO = 0
VID = 1 V
VID = – 1 V
TLE2082C
TA
MIN
TYP
25°C
25°C
TLE2082AC
MAX
MIN
TYP
120
120
– 35
– 35
45
45
MAX
UNIT
dB
mA
TLE2082C operating characteristics at specified free-air temperature, VCC ± = ±5 V
PARAMETER
TEST CONDITIONS
TA†
TLE2082C
MIN
TYP
25°C
SR +
Positive slew rate
SR –
Negative slew rate
ts
Settling time
Vn
Equivalent
q
input noise
voltage
VN(PP)
Peak-to-peak equivalent
q
input noise voltage
VO(PP) = ± 2.3 V,
AVD = – 1,
1
RL = 2 kΩ,
kΩ
F,
See Figure 1
CL = 100 pF,
Full
range
AVD = – 1,
2-V step,,
RL = 1 kΩ,
CL = 100 pF
22
TYP
38
22
38
V/µs
22
0.25
0.25
0.4
0.4
µs
To 1 mV
f = 10 Hz to
10 kHz
f = 0.1Hz to
10 Hz
UNIT
V/µs
25°C
f = 10 kHz
MAX
35
22
To 10 mV
f = 10 Hz
RS = 20 Ω,
See Figure 3
MIN
35
25°C
Full
range
TLE2082AC
MAX
25°C
28
28
11.6
11.6
6
6
0.6
0.6
nV/√Hz
µV
25°C
In
Equivalent input noise
current
VIC = 0,
f = 10 kHz
25°C
2.8
2.8
THD + N
Total harmonic distortion
plus noise
VO(PP) = 5 V,
f = 1 kHz
kHz,
RS = 25 Ω
AVD = 10,
RL = 2 kΩ
kΩ,
25°C
0 013%
0.013%
0 013%
0.013%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
RL = 2 kΩ,,
See Figure 2
25°C
94
9.4
94
9.4
MHz
BOM
Maximum output-swing
g
bandwidth
VO(PP) = 4 V,
RL = 2 kΩ ,
AVD = – 1,
CL = 25 pF
25°C
28
2.8
28
2.8
MHz
φm
Phase margin
g at unity
y
gain
VI = 10 mV,
CL = 25 pF,
RL = 2 kΩ,
See Figure 2
25°C
56°
56°
fA/√Hz
† Full range is 0°C to 70°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
23
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082C electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
TA†
25°C
VIC = 0,
RS = 50 Ω
VO = 0,
VO = 0,,
RS = 50 Ω
IO = – 200 µA
Maximum positive peak
output voltage swing
IO = – 2 mA
IO = – 20 mA
IO = 200 µA
VOM –
Maximum negative
peak
g
output voltage swing
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 10 V
RL = 2 kΩ
RL = 10 kΩ
ri
ci
Input resistance
Input
capacitance
ca
acitance
Common
mode
Differential
13.8
13.6
25°C
13.5
Full range
13.4
25°C
11.5
µV/°C
6
100
6
100
pA
1.4
nA
20
175
20
175
pA
5
nA
15
to
– 11.9
– 13.8
Full range
– 13.7
25°C
– 13.5
Full range
– 13.4
25°C
– 11.5
Full range
– 11.5
25°C
80
Full range
79
25°C
90
Full range
89
25°C
95
Full range
94
15
to
– 11
15
to
– 11.9
15
to
– 10.9
14.1
13.8
14.1
13.9
13.5
13.9
13.4
12.3
11.5
– 14.2
– 13.8
11.5
– 14.2
– 13.7
– 14
–13.5
– 14
– 13.4
– 12.4
– 11.5
– 12.4
96
80
96
79
109
90
109
89
118
95
118
VIC = 0,
See Figure 5
25°C
7.5
7.5
25°C
2.5
2.5
25°C
80
80
Common-mode
rejection ratio
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
kSVR
Supply-voltage
y
g rejection
j
ratio (∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,,
VO = 0,
RS = 50 Ω
25°C
80
Full range
79
25°C
82
Full range
81
† Full range is 0°C to 70°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
dB
94
1012
CMRR
V
– 11.5
1012
f = 1 MHz
V
12.3
25°C
Open-loop output
impedance
V
13.6
11.5
25°C
mV
25
15
to
– 10.9
25°C
4
UNIT
2.4
5
15
to
– 11
MAX
5.1
VIC = 0
zo
24
0.7
1.4
Full range
Full range
7
TYP
25
Full range
Common-mode input
voltage range
MIN
2.4
Full range
25°C
Input bias current
TLE2082AC
MAX
8.1
Full range
Full range
g
VOM +
1.1
25°C
VIC = 0,,
See Figure 4
TYP
Full range
25°C
VICR
TLE2082C
MIN
98
80
98
79
99
82
81
99
Ω
pF
Ω
dB
dB
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless
otherwise noted) (continued)
PARAMETER
ICC
IOS
TEST CONDITIONS
TLE2082C
TA
25°C
Supply current
(both channels)
VO = 0,
No load
Full
range
Crosstalk attenuation
VIC = 0,
RL = 2 kΩ
25°C
VO = 0
VID = 1 V
VID = – 1 V
Short circuit output current
Short-circuit
25°C
TLE2082AC
MIN
TYP
MAX
MIN
TYP
MAX
2.7
3.1
3.9
2.7
3.1
3.9
3.9
3.9
120
120
– 30
– 45
– 30
– 45
30
48
30
48
UNIT
mA
dB
mA
TLE2082C operating characteristics at specified free-air temperature, VCC ± = ±15 V
PARAMETER
SR +
Positive slew rate
SR –
Negative slew rate
ts
Settling time
Vn
Equivalent
q
input noise
voltage
VN(PP)
Peak-to-peak
Peak
to eak equivalent
input noise voltage
TEST CONDITIONS
VO(PP) = 10 V, AVD = – 1,
RL = 2 kΩ
kΩ,
CL = 100 pF,
pF
See Figure 1
AVD = – 1,
10-V step,,
RL = 1 kΩ,
CL = 100 pF
TLE2082C
MIN
TYP
25°C
28
40
Full
range
25
25°C
30
Full
range
25
TLE2082AC
MAX
MIN
TYP
28
40
45
30
V/µs
25
0.4
0.4
1.5
1.5
µs
To 1 mV
25°C
f = 10 Hz to
10 kHz
f = 0.1 Hz to
UNIT
45
25°C
f = 10 kHz
MAX
V/µs
25
To 10 mV
f = 10 Hz
RS = 20 Ω,,
See Figure 3
TA†
28
28
11.6
11.6
6
6
nV/√Hz
V
µV
25°C
10 Hz
06
0.6
06
0.6
In
Equivalent input noise
current
VIC = 0,
f = 10 kHz
25°C
2.8
2.8
THD + N
Total harmonic distortion
plus noise
VO(PP) = 20 V, AVD = 10,
f = 1 kHz
kHz,
RL = 2 kΩ
kΩ,
RS = 25 Ω
25°C
0.008%
0 008%
0.008%
0 008%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
25°C
8
10
8
10
MHz
BOM
Maximum output-swing
g
bandwidth
VO(PP) = 20 V, AVD = – 1,
RL = 2 kΩ,
CL = 25 pF
25°C
478
637
478
637
kHz
φm
Phase margin
g at
unity gain
VI = 10 mV,,
CL = 25 pF,
25°C
RL = 2 kΩ,,
See Figure 2
RL = 2 kΩ,,
See Figure 2
57°
fA/√Hz
57°
† Full range is 0°C to 70°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
25
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082I electrical characteristics at specified free-air temperature, VCC± = ±5 V (unless otherwise
noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
TEST CONDITIONS
TA†
25°C
VIC = 0,
RS = 50 Ω
VO = 0,
VO = 0,,
Maximum positive peak
VOM +
output voltage swing
IO = – 2 mA
IO = – 20 mA
IO = 200 µA
VOM –
Maximum negative
peak
g
output voltage swing
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 2.3
2 3 V RL = 2 kΩ
RL = 10 kΩ
5
to
–1
3.8
3.7
25°C
3.5
Full range
3.4
25°C
1.5
– 3.8
Full range
– 3.7
25°C
– 3.5
Full range
– 3.4
25°C
– 1.5
Full range
– 1.5
25°C
80
Full range
79
25°C
90
Full range
89
25°C
95
Full range
94
µV/°C
5
100
5
100
pA
5
nA
15
175
15
175
pA
10
nA
5
to
– 1.9
5
to
–1
5
to
– 1.9
4.1
3.8
4.1
3.7
3.9
3.5
3.9
2.3
1.5
– 4.2
– 3.8
2.3
1.5
– 4.2
– 3.7
– 4.1
– 3.5
– 4.1
– 2.4
– 1.5
– 2.4
– 1.5
91
80
91
79
100
90
100
106
95
106
94
VIC = 0,,
See Figure 5
25°C
11
11
25°C
2.5
2.5
f = 1 MHz
25°C
CMRR Common-mode
Common mode rejection ratio
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
25°C
70
Full range
68
kSVR
Supply-voltage
ratio
y
g rejection
j
(∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,,
VO = 0,
RS = 50 Ω
25°C
82
Full range
80
ICC
Supplyy current
(both channels)
VO = 0
0,
25°C
2.7
Input
In
ut
capacitance
zo
Open-loop output impedance
Differential
No load
80
Full range
† Full range is – 40°C to 85°C.
26
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
dB
89
1012
ci
V
– 3.4
1012
Common mode
V
3.4
25°C
Input resistance
V
5
to
– 0.8
VIC = 0
ri
mV
25
1.5
25°C
UNIT
2.4
5
to
– 0.8
25°C
4
5.5
10
Full range
Full range
0.65
MAX
25
Full range
IO = – 200 µA
7
TYP
5
25°C
Full range
g
MIN
2.4
Full range
RS = 50 Ω
TLE2082AI
MAX
8.5
Full range
Input bias current
Common-mode input
voltage range
0.9
25°C
VIC = 0,,
See Figure 4
TYP
Full range
25°C
VICR
TLE2082I
MIN
Ω
pF
Ω
80
89
70
89
dB
68
99
82
99
dB
80
2.9
3.9
3.9
2.7
2.9
3.9
3.9
mA
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082I electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise
noted) (continued)
PARAMETER
Crosstalk attenuation
IOS
Short circuit output current
Short-circuit
TEST CONDITIONS
VIC = 0,
RL = 2 kΩ
VO = 0
VID = 1 V
VID = – 1 V
TLE2082I
TA
MIN
TYP
25°C
25°C
TLE2082AI
MAX
MIN
TYP
120
120
– 35
– 35
45
45
MAX
UNIT
dB
mA
TLE2082I operating characteristics at specified free-air temperature, VCC ± = ±5 V
PARAMETER
TEST CONDITIONS
TA†
TLE2082I
MIN
TYP
25°C
SR +
Positive slew rate
SR –
Negative slew rate
ts
Vn
VN(PP)
Settling time
VO(PP) = ± 2.3 V,
AVD = – 1,
1
RL = 2 kΩ,
kΩ
F,
See Figure 1
CL = 100 pF,
AVD = – 1,
2-V step,,
RL = 1 kΩ,
CL = 100 pF
20
TYP
38
20
38
V/µs
20
0.25
0.25
0.4
0.4
µs
To 1 mV
f = 10 Hz to
10 kHz
UNIT
V/µs
25°C
f = 10 kHz
MAX
35
20
To 10 mV
f = 10 Hz
RS = 20 Ω,
See Figure 3
MIN
35
25°C
Full
range
Equivalent
q
input noise
voltage
Peak-to-peak equivalent
q
input noise voltage
Full
range
TLE2082AI
MAX
25°C
28
28
11.6
11.6
6
6
06
0.6
06
0.6
nV/√Hz
µV
25°C
f = 0.1 Hz to
10 Hz
In
Equivalent input noise
current
VIC = 0,
f = 10 kHz
25°C
2.8
2.8
THD + N
Total harmonic distortion
plus noise
VO(PP) = 5 V,
f = 1 kHz
kHz,
RS = 25 Ω
AVD = 10,
RL = 2 kΩ
kΩ,
25°C
0 013%
0.013%
0 013%
0.013%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
RL = 2 kΩ,,
See Figure 2
25°C
94
9.4
94
9.4
MHz
BOM
Maximum output-swing
g
bandwidth
VO(PP) = 4 V,
RL = 2 kΩ ,
AVD = – 1,
CL = 25 pF
25°C
28
2.8
28
2.8
MHz
φm
Phase margin
g at unity
y
gain
VI = 10 mV,
CL = 25 pF,
RL = 2 kΩ,
See Figure 2
25°C
56°
56°
fA/√Hz
† Full range is 40°C to 85°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
27
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082I electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
TA†
25°C
VIC = 0,
RS = 50 Ω
VO = 0,
VO = 0,,
Maximum positive peak
VOM +
output voltage swing
IO = – 2 mA
IO = – 20 mA
IO = 200 µA
VOM –
Maximum negative
peak
g
output voltage swing
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 10 V
RL = 2 kΩ
RL = 10 kΩ
ri
ci
Input resistance
Input
capacitance
ca
acitance
VIC = 0
Common
mode
VIC = 0,,
See Figure
5
g
Differential
zo
Open-loop output
impedance
f = 1 MHz
CMRR
Common-mode
rejection ratio
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
kSVR
Supply-voltage
y
g rejection
j
ratio (∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,,
VO = 0,
RS = 50 Ω
15
to
– 11
13.8
13.7
25°C
13.5
Full range
13.4
25°C
11.5
– 13.8
Full range
– 13.7
25°C
– 13.5
Full range
– 13.4
25°C
– 11.5
Full range
– 11.5
25°C
80
Full range
79
25°C
90
Full range
89
25°C
95
Full range
94
6
100
6
100
pA
5
nA
20
175
20
175
pA
10
nA
POST OFFICE BOX 655303
15
to
– 11.9
15
to
– 11
15
to
– 11.9
15
to
– 10.8
14.1
13.8
14.1
13.9
13.5
13.9
13.4
12.3
11.5
– 14.2
– 13.8
11.5
– 14.2
– 13.7
– 14
–13.5
– 14
– 13.4
– 12.4
– 11.5
– 12.4
96
80
96
79
109
90
109
89
118
95
118
7.5
25°C
2.5
2.5
25°C
80
80
25°C
82
Full range
80
• DALLAS, TEXAS 75265
dB
94
7.5
79
V
– 11.5
25°C
80
V
12.3
1012
25°C
V
13.7
1012
† Full range is – 40°C to 85°C.
28
µV/°C
25°C
Full range
mV
25
11.5
25°C
UNIT
2.4
15
to
– 10.8
25°C
4
5.5
10
Full range
Full range
0.7
MAX
25
Full range
IO = – 200 µA
7
TYP
5
25°C
Full range
g
MIN
2.4
Full range
RS = 50 Ω
TLE2082AI
MAX
8.5
Full range
Input bias current
Common-mode input
voltage range
1.1
25°C
VIC = 0,,
See Figure 4
TYP
Full range
25°C
VICR
TLE2082I
MIN
98
80
98
79
99
82
80
99
Ω
pF
Ω
dB
dB
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082I electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless
otherwise noted) (continued)
PARAMETER
ICC
IOS
TEST CONDITIONS
TLE2082I
TA
25°C
Supply current
(both channels)
VO = 0,
No load
Full
range
Crosstalk attenuation
VIC = 0,
RL = 2 kΩ
25°C
VO = 0
VID = 1 V
VID = – 1 V
Short circuit output current
Short-circuit
25°C
TLE2082AI
MIN
TYP
MAX
MIN
TYP
MAX
2.7
3.1
3.9
2.7
3.1
3.9
3.9
3.9
120
120
– 30
– 45
– 30
– 45
30
48
30
48
UNIT
mA
dB
mA
TLE2082I operating characteristics at specified free-air temperature, VCC ± = ±15 V
PARAMETER
SR +
Positive slew rate
SR –
Negative slew rate
ts
Settling time
Vn
Equivalent
q
input noise
voltage
VN(PP)
Peak-to-peak equivalent
q
input noise voltage
TEST CONDITIONS
VO(PP) = 10 V, AVD = – 1,
RL = 2 kΩ
kΩ,
CL = 100 pF,
pF
See Figure 1
AVD = – 1,
10-V step,,
RL = 1 kΩ,
CL = 100 pF
TLE2082I
MIN
TYP
25°C
28
40
Full
range
22
25°C
30
Full
range
22
TLE2082AI
MAX
MIN
TYP
28
40
45
30
V/µs
22
0.4
0.4
1.5
1.5
µs
To 1 mV
f = 10 Hz to
10 kHz
UNIT
45
25°C
f = 10 kHz
MAX
V/µs
22
To 10 mV
f = 10 Hz
RS = 20 Ω,
See Figure 3
TA†
25°C
28
28
11.6
11.6
6
6
06
0.6
06
0.6
nV/√Hz
µV
25°C
f = 0.1 Hz to
10 Hz
In
Equivalent input noise
current
VIC = 0,
f = 10 kHz
25°C
2.8
2.8
THD + N
Total harmonic distortion
plus noise
VO(PP) = 20 V, AVD = 10,
f = 1 kHz
kHz,
RL = 2 kΩ
kΩ,
RS = 25 Ω
25°C
0 008%
0.008%
0 008%
0.008%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
25°C
8
10
8
10
MHz
BOM
Maximum output-swing
g
bandwidth
VO(PP) = 20 V, AVD = – 1,
RL = 2 kΩ,
CL = 25 pF
25°C
478
637
478
637
kHz
φm
Phase margin
g at unity
y
gain
VI = 10 mV,
CL = 25 pF,
25°C
RL = 2 kΩ,,
See Figure 2
RL = 2 kΩ,
See Figure 2
57°
fA/√Hz
57°
† Full range is – 40°C to 85°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
29
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless
otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
TEST CONDITIONS
TA†
VO = 0,
VO = 0,,
IO = – 2 mA
IO = – 20 mA
IO = 200 µA
VOM –
Maximum negative
peak
g
output voltage swing
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 2.3
23V
RL = 2 kΩ
RL = 10 kΩ
ri
Input resistance
ci
Input
capaci
capacitance
zo
Open-loop output impedance
VIC = 0
Common mode
Differential
VIC = 0
0,
5
to
–1
3.8
3.6
25°C
3.5
Full range
3.3
25°C
1.5
– 3.8
Full range
– 3.6
25°C
– 3.5
Full range
– 3.3
25°C
– 1.5
Full range
– 1.4
25°C
80
Full range
78
25°C
90
Full range
88
25°C
95
Full range
93
5
100
5
100
pA
20
nA
15
175
15
175
pA
60
nA
5
to
– 1.9
5
to
–1
5
to
– 1.9
5
to
– 0.8
4.1
3.8
4.1
3.9
3.5
3.9
3.3
2.3
1.5
– 4.2
– 3.8
V
2.3
1.4
– 4.2
– 3.6
– 4.1
– 3.5
– 4.1
– 3.3
– 2.4
– 1.5
V
– 2.4
– 1.4
91
80
91
78
100
90
100
88
106
95
dB
106
93
1012
25°C
11
11
25°C
2.5
2.5
See Figure 5
Ω
pF
CMRR Common-mode
Common mode rejection ratio
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
25°C
70
Full range
68
Supply-voltage
y
g rejection
j
ratio
(∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,,
VO = 0,
RS = 50 Ω
25°C
82
Full range
80
80
∗On products compliant with MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
POST OFFICE BOX 655303
V
3.6
1012
25°C
30
µV/°C
25°C
f = 1 MHz
kSVR
mV
25∗
1.4
25°C
UNIT
2.3
5
to
– 0.8
25°C
4
6.5
60
Full range
Full range
0.65
MAX
25∗
Full range
IO = – 200 µA
7
TYP
20
25°C
Full range
g
MIN
2.3
Full range
RS = 50 Ω
TLE2082AM
MAX
9.5
Full range
Input bias current
Maximum positive peak
VOM +
output voltage swing
0.9
Full range
25°C
VIC = 0,,
See Figure 4
Common-mode input
voltage range
TYP
25°C
VIC = 0,
RS = 50 Ω
25°C
VICR
TLE2082M
MIN
• DALLAS, TEXAS 75265
89
80
70
89
68
99
82
80
99
Ω
dB
dB
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless
otherwise noted) (continued)
PARAMETER
ICC
IOS
TEST CONDITIONS
TA†
25°C
Supply current
(both channels)
VO = 0,
No load
Full
range
Crosstalk attenuation
VIC = 0,
RL = 2 kΩ
25°C
VO = 0
VID = 1 V
VID = – 1 V
Short circuit output current
Short-circuit
TLE2082M
TLE2082AM
MIN
TYP
MAX
MIN
TYP
MAX
2.7
2.9
3.6
2.7
2.9
3.6
3.6
25°C
3.6
120
120
– 35
– 35
45
45
UNIT
mA
dB
mA
† Full range is – 55°C to 125°C.
TLE2082M operating characteristics at specified free-air temperature, VCC± = ±5 V
PARAMETER
TEST CONDITIONS
TA†
TLE2082M
MIN
TYP
25°C
SR +
Positive slew rate
SR –
Negative slew rate
ts
Settling time
Vn
Equivalent
q
input noise
voltage
VN(PP)
Peak-to-peak equivalent
q
input noise voltage
VO(PP) = ± 2.3 V,
AVD = – 1,
RL = 2 kΩ,
1
kΩ
CL = 100 pF,
F,
See Figure 1
Full
range
AVD = – 1,
2-V step,,
RL = 1 kΩ,
CL = 100 pF
18∗
MIN
TYP
38
18∗
38
V/µs
18∗
0.25
0.25
0.4
0.4
28
28
11.6
11.6
6
6
06
0.6
06
0.6
µs
To 1 mV
f = 10 Hz to
10 kHz
UNIT
V/µs
25°C
f = 10 kHz
MAX
35
18∗
To 10 mV
f = 10 Hz
RS = 20 Ω,
See Figure 3
MAX
35
25°C
Full
range
TLE2082AM
25°C
nV/√Hz
µV
25°C
f = 0.1 Hz to
10 Hz
In
Equivalent input noise
current
VIC = 0,
f = 10 kHz
25°C
2.8
2.8
THD + N
Total harmonic
distortion plus noise
VO(PP) = 5 V,
f = 1 kHz
kHz,
RS = 25 Ω
AVD = 10,
RL = 2 kΩ
kΩ,
25°C
0 013%
0.013%
0 013%
0.013%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
RL = 2 kΩ,,
See Figure 2
25°C
94
9.4
94
9.4
MHz
BOM
Maximum output-swing
g
bandwidth
VO(PP) = 4 V,
RL = 2 kΩ ,
AVD = – 1,
CL = 25 pF
25°C
28
2.8
28
2.8
MHz
φm
Phase margin
g at unity
y
gain
VI = 10 mV,
CL = 25 pF,
RL = 2 kΩ,
See Figure 2
25°C
56°
56°
fA/√Hz
∗On products compliant with MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
31
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082M electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
TA†
VO = 0,
VO = 0,,
IO = – 200 µA
Maximum positive peak
output voltage swing
IO = – 2 mA
IO = – 20 mA
IO = 200 µA
VOM –
Maximum negative
peak
g
output voltage swing
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 10 V
RL = 2 kΩ
RL = 10 kΩ
ri
ci
Input resistance
Input
capacitance
ca
acitance
VIC = 0
Common
mode
VIC = 0,,
See Figure
5
g
Differential
zo
Open-loop output
impedance
f = 1 MHz
CMRR
Common-mode rejection
j
ratio
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
kSVR
Supply-voltage
y
g rejection
j
ratio (∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,,
VO = 0,
RS = 50 Ω
15
to
– 11
13.8
13.6
25°C
13.5
Full range
13.3
25°C
11.5
– 13.8
Full range
– 13.6
25°C
– 13.5
Full range
– 13.3
25°C
– 11.5
Full range
– 11.4
25°C
80
Full range
78
25°C
90
Full range
88
25°C
95
Full range
93
µV/°C
6
100
6
100
pA
20
nA
20
175
20
175
pA
65
nA
15
to
– 11.9
POST OFFICE BOX 655303
15
to
– 11
15
to
– 11.9
15
to
– 10.8
14.1
13.8
14.1
13.9
13.5
13.9
13.3
12.3
11.5
– 14.2
– 13.8
11.4
– 14.2
– 13.6
– 14
–13.5
– 14
– 13.3
– 12.4
– 11.5
– 12.4
96
80
96
78
109
90
109
88
118
95
118
7.5
7.5
25°C
2.5
2.5
25°C
80
80
25°C
82
Full range
80
• DALLAS, TEXAS 75265
dB
93
25°C
78
V
– 11.4
1012
80
V
12.3
1012
25°C
V
13.6
25°C
Full range
mV
25∗
11.4
25°C
4
UNIT
2.4
15
to
– 10.8
25°C
MAX
6.5
65
∗On products compliant with MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
32
0.7
20
Full range
Full range
7
TYP
25∗
Full range
RS = 50 Ω
MIN
2.4
Full range
25°C
Input bias current
TLE2082AM
MAX
9.5
Full range
Full range
g
VOM +
1.1
Full range
25°C
VIC = 0,,
See Figure 4
Common-mode input
voltage range
TYP
25°C
VIC = 0,
RS = 50 Ω
25°C
VICR
TLE2082M
MIN
98
80
98
78
99
82
80
99
Ω
pF
Ω
dB
dB
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082M electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted) (continued)
PARAMETER
ICC
IOS
TEST CONDITIONS
TA†
25°C
Supply current
(both channels)
VO = 0,
No load
Full
range
Crosstalk attenuation
VIC = 0,
RL = 2 kΩ
25°C
VO = 0
VID = 1 V
VID = – 1 V
Short-circuit output
current
25°C
TLE2082M
TLE2082AM
MIN
TYP
MAX
MIN
TYP
MAX
2.7
3.1
3.6
2.7
3.1
3.6
3.6
3.6
120
120
– 30
– 45
– 30
– 45
30
48
30
48
UNIT
mA
dB
mA
† Full range is – 55°C to 125°C.
TLE2082M operating characteristics at specified free-air temperature, VCC± = ±15 V
PARAMETER
SR +
Positive slew rate
SR –
Negative slew rate
ts
Settling time
Vn
Equivalent
q
input noise
voltage
VN(PP)
Peak-to-peak equivalent
q
input noise voltage
TEST CONDITIONS
VO(PP) = 10 V, AVD = – 1,
RL = 2 kΩ
kΩ,
CL = 100 pF,
pF
See Figure 1
AVD = – 1,
10-V step,,
RL = 1 kΩ,
CL = 100 pF
TLE2082M
MIN
TYP
25°C
28
40
Full
range
20
25°C
30
Full
range
20
TLE2082AM
MAX
MIN
TYP
28
40
45
30
V/µs
20
0.4
0.4
1.5
1.5
28
28
11.6
11.6
6
6
µs
To 1 mV
f = 10 Hz to
10 kHz
25°C
06
0.6
06
0.6
In
Equivalent input noise
current
f = 10 kHz
25°C
2.8
2.8
THD + N
VO(PP) = 20 V, AVD = 10,
Total harmonic distortion
kHz,
RL = 2 kΩ
kΩ,
f = 1 kHz
plus noise
RS = 25 Ω
25°C
0.008%
0 008%
0.008%
0 008%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
BOM
Maximum output-swing
g
bandwidth
φm
Phase margin
g at unity
y
gain
RL = 2 kΩ,,
See Figure 2
nV/√Hz
µV
25°C
f = 0.1 Hz to
10 Hz
VIC = 0,
UNIT
45
25°C
f = 10 kHz
MAX
V/µs
20
To 10 mV
f = 10 Hz
RS = 20 Ω,
See Figure 3
TA†
fA/√Hz
25°C
8∗
10
8∗
10
MHz
VO(PP) = 20 V, AVD = – 1,
RL = 2 kΩ,
CL = 25 pF
25°C
478∗
637
478∗
637
kHz
VI = 10 mV,
CL = 25 pF,
25°C
RL = 2 kΩ,
See Figure 2
57°
57°
∗On products compliant with MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
33
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082Y electrical characteristics at VCC± = ±15 V, TA = 25°C
PARAMETER
TEST CONDITIONS
VIO
IIO
Input offset voltage
IIB
Input bias current
VICR
Common-mode input voltage
g range
g
RS = 50 Ω
Maximum positive peak output voltage swing
VOM +
VOM –
AVD
ri
VIC = 0,
Input offset current
VO = 0,
VIC = 0
0,
Maximum negative peak output voltage swing
Large-signal differential voltage amplification
Input resistance
VO = 0
0,
pA
20
175
pA
13.5
13.9
IO = – 20 mA
IO = 200 µA
11.5
12.3
– 13.8
– 14.2
– 13.5
– 14
– 11.5
– 12.4
RL = 600 Ω
80
96
VO = ± 10 V
RL = 2 kΩ
90
109
RL = 10 kΩ
95
118
VO = 0
0,
Open-loop output impedance
f = 1 MHz
Common-mode rejection ratio
kSVR
Supply-voltage rejection ratio (∆VCC± /∆VIO)
VIC = VICRmin, VO = 0,
VCC ± = ± 5 V to ±15 V,
RS = 50 Ω
ICC
Supply current (both channels)
V
V
dB
Ω
7.5
See Figure 5
VO = 0,
No load
VO = 0
VID = 1 V
VID = – 1 V
POST OFFICE BOX 655303
V
1012
CMRR
Differential
mV
14.1
VIC = 0
Common mode
6
100
13.8
IO = 2 mA
IO = 20 mA
• DALLAS, TEXAS 75265
UNIT
6
IO = – 200 µA
IO = – 2 mA
zo
34
See Figure 4
MAX
1.1
15
to
11.9
Input capacitance
Short circuit output current
Short-circuit
RS = 50 Ω
TYP
15
to
– 11
ci
IOS
TLE2082Y
MIN
pF
2.5
80
Ω
RS = 50 Ω
80
98
dB
VO = 0,
82
99
dB
2.7
3.1
– 30
– 45
30
48
3.9
mA
mA
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2084C electrical characteristics at specified free-air temperature, VCC± = ±5 V (unless
otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
Input bias current
TEST CONDITIONS
TA†
25°C
VIC = 0,
RS = 50 Ω
VO = 0,
VICR
25°C
VO = 0,
Maximum positive peak
output voltage swing
IO = – 2 mA
IO = – 20 mA
IO = 200 µA
VOM –
Maximum negative
peak
g
output voltage swing
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 2
2.3
3V
RL = 2 kΩ
RL = 10 kΩ
– 0.5
25°C
3.8
3.7
25°C
3.5
Full range
3.4
25°C
1.5
Full range
1.5
25°C
– 3.8
Full range
– 3.7
25°C
– 3.5
Full range
– 3.4
25°C
– 1.5
Full range
– 1.5
25°C
80
Full range
79
25°C
90
Full range
89
25°C
95
Full range
94
25°C
ci
Input capacitance
zo
Open-loop output
impedance
f = 1 MHz
CMRR
Common-mode
rejection ratio
VIC = VICRmin,
VO = 0,
RS = 50 Ω
25°C
70
Full range
68
kSVR
Supply-voltage
y
g rejection
j
ratio (∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,
VO = 0,
RS = 50 Ω
25°C
82
Full range
80
ICC
Supply
y current
( four amplifiers )
VO = 0
0,
No load
25°C
5.2
VIC = 0,
RL = 2 kΩ
µV/°C
15
100
15
100
pA
1.4
nA
175
pA
5
nA
175
20
5
to
– 1.9
5
to
–1
5
to
– 1.9
V
5
to
– 0.9
4.1
3.8
4.1
3.7
3.9
3.5
3.9
2.3
1.5
2.3
1.5
– 4.2
– 3.8
– 4.2
– 3.7
– 4.1
– 3.5
– 4.1
– 2.4
– 1.5
– 2.4
– 1.5
91
80
91
79
100
90
100
dB
89
106
95
106
94
Ω
1012
25°C
11
11
25°C
2.5
2.5
25°C
80
80
89
70
pF
Ω
89
dB
68
99
82
99
dB
80
6.3
Full range
• DALLAS, TEXAS 75265
V
– 3.4
Differential
POST OFFICE BOX 655303
V
3.4
Common mode
25°C
mV
30
1012
Input resistance
UNIT
10.1
5
to
– 0.9
Full range
4
6.1
5
5
to
–1
MAX
30
20
ri
ax
Crosstalk attenuation
† Full range is 0°C to 70°C.
VIC = 0
VIC = 0,
See Figure 5
7
TYP
1.4
25°C
IO = – 200 µA
MIN
10.1
Full range
RS = 50 Ω
TLE2084AC
MAX
9.1
Full range
Full range
VOM +
–1.6
Full range
VIC = 0,
See Figure 4
TYP
Full range
25°C
Common-mode input
voltage range
TLE2084C
MIN
7.5
5.2
6.3
7.5
120
7.5
7.5
120
mA
dB
35
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2084C electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless
otherwise noted) (continued)
PARAMETER
IOS
Short-circuit output
current
TEST CONDITIONS
VID = 1 V
VID = – 1 V
VO = 0
TA†
TLE2084C
MIN
25°C
TYP
TLE2084AC
MAX
MIN
TYP
– 35
– 35
45
45
MAX
UNIT
mA
† Full range is 0°C to 70°C.
TLE2084C operating characteristics at specified free-air temperature, VCC± = ±5 V
PARAMETER
TEST CONDITIONS
TA†
TLE2084C
MIN
TYP
25°C
SR +
Positive slew rate
SR –
Negative slew rate
ts
Vn
VN(PP)
Settling time
VO(PP) = ± 2.3 V,
AVD = – 1,
RL = 2 kΩ,
1
kΩ
CL = 100 pF,
F,
See Figure 1
AVD = – 1,
2-V step,
RL = 1 kΩ,
CL = 100 pF
Peak-to-peak equivalent
input noise voltage
TYP
38
38
V/µs
22
0.25
0.25
0.4
0.4
µs
To 1 mV
f = 10 Hz to
10 kHz
f = 0.1Hz to
10 Hz
UNIT
V/µs
22
22
MAX
35
25°C
f = 10 kHz
RS = 20 Ω,
See Figure 3
22
25°C
Full
range
MIN
35
To 10 mV
f = 10 Hz
Equivalent
q
input noise
voltage
Full
range
TLE2084AC
MAX
25°C
28
28
11.6
11.6
6
6
0.6
0.6
nV/√Hz
µV
25°C
In
Equivalent input noise
current
VIC = 0,
f = 10 kHz
25°C
2.8
2.8
THD + N
Total harmonic distortion
plus noise
VO(PP) = 5 V,
f = 1 kHz
kHz,
RS = 25 Ω
AVD = 10,
RL = 2 kΩ
kΩ,
25°C
0 013%
0.013%
0 013%
0.013%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,
CL = 25 pF,
RL = 2 kΩ,
See Figure 2
25°C
94
9.4
94
9.4
MHz
BOM
Maximum output-swing
g
bandwidth
VO(PP) = 4 V,
RL = 2 kΩ ,
AVD = – 1,
CL = 25 pF
25°C
28
2.8
28
2.8
MHz
φm
Phase margin
g at unity
y
gain
VI = 10 mV,
CL = 25 pF,
RL = 2 kΩ,
See Figure 2
25°C
56°
56°
† Full range is 0°C to 70°C.
36
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
fA /√Hz
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2084C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless
otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
Input bias current
TA†
TEST CONDITIONS
VICR
VO = 0,
25°C
VIC = 0,
See Figure 4
VO = 0,
VOM –
Maximum
M
i
negative
ti
peak
eak output
out ut voltage
swing
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 10 V
RL = 2 kΩ
RL = 10 kΩ
13.8
13.7
25°C
13.5
Full range
13.4
25°C
11.5
Full range
11.5
25°C
– 13.8
Full range
– 13.7
25°C
– 13.7
Full range
– 13.6
25°C
– 11.5
Full range
– 11.5
25°C
80
Full range
79
25°C
90
Full range
89
25°C
95
Full range
94
15
100
15
100
pA
1.4
nA
175
pA
5
nA
175
25
15
to
– 11.9
15
to
– 11
15
to
– 11.9
V
15
to
– 10.9
14.1
13.8
14.1
13.7
13.9
13.5
13.9
12.3
11.5
12.3
11.5
– 14.2
– 13.8
– 14.2
– 13.7
– 14
–13.7
– 14
– 12.4
– 11.5
– 12.4
– 11.5
96
80
96
79
109
90
109
118
95
118
94
25°C
7.5
7.5
Differential
25°C
2.5
2.5
25°C
80
80
zo
Open-loop output
impedance
f = 1 MHz
CMRR
Common-mode
rejection ratio
VIC = VICRmin,
VO = 0,
RS = 50 Ω
25°C
80
Full range
79
kSVR
Supply-voltage
y
g rejection
j
ratio (∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,
VO = 0,
RS = 50 Ω
25°C
82
Full range
81
ICC
Supply
y current
( four amplifiers )
VO = 0
0,
No load
25°C
5.2
VIC = 0,
RL = 2 kΩ
98
25°C
• DALLAS, TEXAS 75265
80
Ω
pF
Ω
98
dB
79
99
82
99
dB
81
6.5
Full range
POST OFFICE BOX 655303
dB
89
Common mode
Input capacitance
V
– 13.6
1012
ci
V
13.4
1012
Input resistance
mV
µV/°C
25°C
ri
ax
Crosstalk attenuation
† Full range is 0°C to 70°C.
VIC = 0
VIC = 0,
See Figure 5
25°C
UNIT
30
15
to
– 10.9
Full range
4
6.1
5
15
to
MAX
10.1
25
– 11
IO = 200 µA
– 0.5
1.4
25°C
IO = – 20 mA
7
TYP
30
Full range
IO = – 2 mA
MIN
10.1
Full range
RS = 50 Ω
TLE2084AC
MAX
9.1
Full range
IO = – 200 µA
Maximum positive peak
output voltage swing
–1.6
Full range
Full range
g
VOM +
TYP
25°C
VIC = 0,
RS = 50 Ω
25°C
Common-mode input
voltage range
TLE2084C
MIN
7.5
5.2
6.5
7.5
120
7.5
7.5
120
mA
dB
37
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2084C electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted) (continued)
PARAMETER
IOS
Short-circuit output
current
TEST CONDITIONS
VID = 1 V
VID = – 1 V
VO = 0
TA†
25°C
TLE2084C
MIN
TYP
– 30
30
TLE2084AC
MAX
MIN
TYP
– 45
– 30
– 45
48
30
48
MAX
UNIT
mA
† Full range is 0°C to 70°C.
TLE2084C operating characteristics at specified free-air temperature, VCC± = ±15 V
PARAMETER
SR +
TEST CONDITIONS
Positive slew rate
VO(PP) = 10 V, AVD = – 1,
RL = 2 kΩ
kΩ,
pF,
CL = 100 pF
See Figure 1
SR –
ts
Negative slew rate
Settling time
Vn
Equivalent
q
input noise
voltage
VN(PP)
Peak to eak equivalent
Peak-to-peak
input noise voltage
AVD = – 1,
10-V step,,
RL = 1 kΩ,
CL = 100 pF
MIN
TYP
25°C
25
40
Full
range
22
25°C
30
Full
range
25
TLE2084AC
MAX
MIN
TYP
25
40
45
30
V/µs
25
0.4
0.4
1.5
1.5
µs
To 1 mV
25°C
f = 10 Hz to
10 kHz
f = 0.1 Hz to
28
28
11.6
11.6
6
6
06
0.6
06
0.6
In
Equivalent input noise
current
f = 10 kHz
25°C
2.8
2.8
THD + N
VO(PP) = 20 V, AVD = 10,
Total harmonic distortion
f = 1 kHz
kHz,
RL = 2 kΩ
kΩ,
plus noise
RS = 25 Ω
25°C
0 008%
0.008%
0 008%
0.008%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
BOM
Maximum output-swing
g
bandwidth
φm
Phase margin
g at
unity gain
RL = 2 kΩ,,
See Figure 2
fA /√Hz
25°C
8
10
8
10
MHz
VO(PP) = 20 V,, AVD = – 1,,
RL = 2 kΩ,
CL = 25 pF
25°C
478
637
478
637
kHz
VI = 10 mV,
CL = 25 pF,
25°C
RL = 2 kΩ,
See Figure 2
† Full range is 0°C to 70°C.
38
nV/√Hz
µV
V
25°C
10 Hz
VIC = 0,
UNIT
45
25°C
f = 10 kHz
MAX
V/µs
22
To 10 mV
f = 10 Hz
RS = 20 Ω,,
See Figure 3
TLE2084C
TA†
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
57°
57°
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2084M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless
otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
Input bias current
TA†
TEST CONDITIONS
VICR
VO = 0,
25°C
VIC = 0,
See Figure 4
VO = 0,
Maximum
M
i
negative
ti
peak
eak out
output
ut voltage
swing
IO = 2 mA
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 2.3
23V
RL = 2 kΩ
RL = 10 kΩ
VIC = 0
VIC = 0,
See Figure 5
25°C
3.8
3.6
25°C
3.5
Full range
3.3
25°C
1.5
Full range
1.4
25°C
– 3.8
Full range
– 3.6
25°C
– 3.5
Full range
– 3.3
25°C
– 1.5
Full range
– 1.4
25°C
80
Full range
78
25°C
90
Full range
88
25°C
95
Full range
93
Input resistance
25°C
ci
Input capacitance
zo
Open-loop output
impedance
f = 1 MHz
CMRR
Common-mode
rejection ratio
VIC = VICRmin,
VO = 0,
RS = 50 Ω
25°C
70
Full range
68
kSVR
Supply-voltage
y
g rejecj
tion ratio (∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,
VO = 0,
RS = 50 Ω
25°C
82
Full range
80
ICC
Supply
y current
( four amplifiers )
VO = 0
0,
15
100
15
100
pA
20
nA
175
pA
65
nA
175
20
5
to
– 1.9
5
to
–1
25°C
5.2
5
to
– 1.9
V
5
to
– 0.8
4.1
3.8
4.1
3.6
3.9
3.5
3.9
2.3
1.5
2.3
1.4
– 4.2
– 3.8
– 4.2
– 3.6
– 4.1
– 3.5
– 4.1
V
– 3.3
– 2.4
– 1.5
– 2.4
– 1.4
91
80
91
78
100
90
100
dB
88
106
95
106
93
25°C
11
11
25°C
2.5
2.5
25°C
80
80
89
70
pF
Ω
89
dB
68
99
82
99
dB
80
6.3
Full range
ax
Crosstalk attenuation
VIC = 0,
RL = 2 kΩ
25°C
120
∗On products compliant with MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
• DALLAS, TEXAS 75265
Ω
1012
Differential
POST OFFICE BOX 655303
V
3.3
Common mode
No load
mV
µV/°C
1012
ri
UNIT
30∗
5
to
– 0.8
Full range
4
9.5
65
5
to
MAX
10.1
20
–1
IO = 200 µA
– 0.5
20
25°C
IO = – 20 mA
7
TYP
30∗
Full range
IO = – 2 mA
MIN
10.1
Full range
RS = 50 Ω
TLE2084AM
MAX
12.5
Full range
IO = – 200 µA
VOM –
–1.6
Full range
Full range
g
Maximum positive peak
VOM +
output voltage swing
TYP
25°C
VIC = 0,
RS = 50 Ω
25°C
Common-mode input
voltage range
TLE2084M
MIN
7.5
5.2
6.3
7.5
7.5
7.5
120
mA
dB
39
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2084M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless
otherwise noted) (continued)
PARAMETER
IOS
Short-circuit output
current
TEST CONDITIONS
VID = 1 V
VID = – 1 V
VO = 0
TLE2084M
TA
MIN
TYP
TLE2084AM
MAX
MIN
TYP
– 35
– 35
45
45
25°C
MAX
UNIT
mA
TLE2084M operating characteristics at specified free-air temperature, VCC ± = ±5 V
PARAMETER
TEST CONDITIONS
TA†
TLE2084M
MIN
TYP
25°C
SR +
Positive slew rate
SR –
Negative slew rate
ts
Settling time
Vn
Equivalent
q
input noise
voltage
VN(PP)
Peak-to-peak equivalent
q
input noise voltage
VO(PP) = ± 2.3 V,
AVD = – 1
1,
RL = 2 kΩ
kΩ,
CL = 100 pF,
F,
See Figure 1
Full
range
AVD = – 1,
2-V step,,
RL = 1 kΩ,
CL = 100 pF
18∗
TYP
38
18∗
38
V/µs
18∗
0.25
0.25
0.4
0.4
28
28
11.6
11.6
6
6
µs
To 1 mV
f = 10 Hz to
10 kHz
UNIT
V/µs
25°C
f = 10 kHz
MAX
35
18∗
To 10 mV
f = 10 Hz
RS = 20 Ω,
See Figure 3
MIN
35
25°C
Full
range
TLE2084AM
MAX
25°C
nV/√Hz
µV
25°C
f = 0.1 Hz to
10 Hz
06
0.6
06
0.6
In
Equivalent input noise
current
VIC = 0,
f = 10 kHz
25°C
2.8
2.8
THD + N
Total harmonic distortion
plus noise
VO(PP) = 5 V,
f = 1 kHz
kHz,
RS = 25 Ω
AVD = 10,
RL = 2 kΩ
kΩ,
25°C
0 013%
0.013%
0 013%
0.013%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
RL = 2 kΩ,,
See Figure 2
25°C
94
9.4
94
9.4
MHz
BOM
Maximum output-swing
g
bandwidth
VO(PP) = 4 V,,
RL = 2 kΩ ,
AVD = – 1,,
CL = 25 pF
25°C
28
2.8
28
2.8
MHz
φm
Phase margin
g at unity
y
gain
VI = 10 mV,
CL = 25 pF,
RL = 2 kΩ,
See Figure 2
25°C
56°
56°
∗On products compliant with MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
40
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
fA /√Hz
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2084M electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient
of input offset voltage
IIO
Input offset current
IIB
Input bias current
TA†
TEST CONDITIONS
VICR
VO = 0,
25°C
VIC = 0,
See Figure 4
VO = 0,
Maximum negative
peak
g
IO = 2 mA
output voltage swing
IO = 20 mA
RL = 600 Ω
AVD
Large-signal
g
g
differential
voltage amplification
VO = ± 10 V
RL = 2 kΩ
RL = 10 kΩ
VIC = 0
VIC = 0,
See Figure 5
25°C
13.8
13.6
25°C
13.5
Full range
13.3
25°C
11.5
Full range
11.4
25°C
– 13.8
Full range
– 13.6
25°C
– 13.5
Full range
– 13.3
25°C
– 11.5
Full range
– 11.4
25°C
80
Full range
78
25°C
90
Full range
88
25°C
95
Full range
93
15
100
15
100
pA
20
nA
175
pA
65
nA
175
25
15
to
– 11.9
15
to
– 11
15
to
– 11.9
V
15
to
– 10.8
14.1
13.8
14.1
13.6
13.9
13.5
13.9
12.3
11.5
12.3
11.4
– 14.2
– 13.8
– 14.2
– 13.6
– 14
–13.5
– 14
– 12.4
– 11.5
– 12.4
– 11.4
96
80
96
78
109
90
109
118
95
118
93
25°C
7.5
7.5
Differential
25°C
2.5
2.5
25°C
80
80
zo
Open-loop output
impedance
f = 1 MHz
CMRR
Common-mode
rejection ratio
VIC = VICRmin,
VO = 0,
RS = 50 Ω
25°C
80
Full range
78
kSVR
Supply-voltage
y
g rejection
j
ratio (∆VCC± /∆VIO)
VCC ± = ± 5 V to ± 15 V,
VO = 0,
RS = 50 Ω
25°C
82
Full range
80
ICC
Supply
y current
( four amplifiers )
VO = 0
0,
25°C
5.2
No load
98
99
pF
Ω
98
dB
82
99
dB
80
6.5
ax
Crosstalk attenuation
VIC = 0,
RL = 2 kΩ
25°C
120
∗On products compliant with MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
• DALLAS, TEXAS 75265
80
Ω
78
Full range
POST OFFICE BOX 655303
dB
88
Common mode
Input capacitance
V
– 13.3
1012
ci
V
13.3
1012
Input resistance
mV
µV/°C
25°C
ri
UNIT
30∗
15
to
– 10.8
Full range
4
7.5
65
15
to
MAX
10.1
25
– 11
IO = 200 µA
– 0.5
20
25°C
IO = – 20 mA
7
TYP
30∗
Full range
IO = – 2 mA
MIN
10.1
Full range
RS = 50 Ω
TLE2084AM
MAX
12.5
Full range
IO = – 200 µA
VOM –
–1.6
Full range
Full range
g
Maximum positive peak
VOM +
output voltage swing
TYP
25°C
VIC = 0,
RS = 50 Ω
25°C
Common-mode input
voltage range
TLE2084M
MIN
7.5
5.2
6.5
7.5
7.5
7.5
120
mA
dB
41
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2084M electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted) (continued)
PARAMETER
IOS
Short-circuit output
current
TEST CONDITIONS
VID = 1 V
VID = – 1 V
VO = 0
TLE2084M
TA
25°C
MIN
TYP
– 30
30
TLE2084AM
MAX
MIN
TYP
– 45
– 30
– 45
48
30
48
MAX
UNIT
mA
TLE2084M operating characteristics at specified free-air temperature, VCC ± = ±15 V
PARAMETER
SR +
TEST CONDITIONS
Positive slew rate
SR –
Negative slew rate
ts
Settling time
Vn
Equivalent
q
input noise
voltage
VN(PP)
Peak-to-peak equivalent
q
input noise voltage
VO(PP) = 10 V,
AVD = – 1
1,
RL = 2 kΩ
kΩ,
CL = 100 pF,
F,
See Figure 1
AVD = – 1,
10-V step,,
RL = 1 kΩ,
CL = 100 pF
MIN
TYP
25°C
25
40
Full
range
17
25°C
30
Full
range
20
TLE2084AM
MAX
MIN
TYP
25
40
45
30
V/µs
20
0.4
0.4
1.5
1.5
28
28
11.6
11.6
6
6
06
0.6
06
0.6
µs
To 1 mV
f = 10 Hz to
10 kHz
UNIT
45
25°C
f = 10 kHz
MAX
V/µs
17
To 10 mV
f = 10 Hz
RS = 20 Ω,
See Figure 3
TLE2084M
TA†
25°C
nV/√Hz
µV
25°C
f = 0.1 Hz to
10 Hz
In
Equivalent
q
input noise
current
VIC = 0,
0
f = 10 kHz
25°C
28
2.8
28
2.8
THD + N
Total harmonic distortion
plus noise
VO(PP) = 20 V, AVD = 10,
f = 1 kHz
kHz,
RL = 2 kΩ
kΩ,
RS = 25 Ω
25°C
0 008%
0.008%
0 008%
0.008%
B1
Unity gain bandwidth
Unity-gain
VI = 10 mV,,
CL = 25 pF,
25°C
8∗
10
8∗
10
MHz
BOM
Maximum output-swing
g
bandwidth
VO(PP) = 20 V,, AVD = – 1,,
RL = 2 kΩ,
CL = 25 pF
25°C
478∗
637
478∗
637
kHz
RL = 2 kΩ,,
See Figure 2
VI = 10 mV,,
RL = 2 kΩ,,
25°C
57°
CL = 25 pF,
See Figure 2
∗On products compliant with MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
φm
42
Phase margin
g at unityy
gain
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
57°
fA /√Hz
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2084Y electrical characteristics at VCC± = ±15 V, TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIO
Input offset voltage
IIO
IIB
Input offset current
Input bias current
VIC = 0,
RS = 50 Ω
VIC = 0,
See Figure 4
VICR
Common-mode input voltage
g range
g
RS = 50 Ω
VOM +
Maximum positive peak output voltage swing
VOM –
AVD
ri
Maximum negative peak output voltage swing
Large-signal differential voltage amplification
Input resistance
VO = 0,
15
100
pA
25
175
pA
IO = – 200 µA
IO = – 2 mA
13.8
14.1
13.5
13.9
IO = – 20 mA
IO = 200 µA
11.5
12.3
– 13.8
– 14.2
– 13.5
– 14
– 11.5
– 12.4
VO = ± 10 V
VIC = 0
VIC = 0,
See Figure 5
V
V
V
RL = 600 Ω
80
96
RL = 2 kΩ
90
109
dB
RL = 10 kΩ
95
118
1012
Ω
Common mode
7.5
Differential
2.5
zo
Open-loop output impedance
f = 1 MHz
CMRR
Common-mode rejection ratio
VIC = VICRmin,
RS = 50 Ω
kSVR
Supply-voltage rejection ratio (∆VCC± /∆VIO)
VCC ± = ± 5 V to ±15 V, VO = 0,
RS = 50 Ω
ICC
Supply current ( four amplifiers )
VO = 0,
No load
VO = 0
VID = 1 V
VID = – 1 V
POST OFFICE BOX 655303
UNIT
mV
15
to
11.9
IO = 2 mA
IO = 20 mA
MAX
7
15
to
– 11
Input capacitance
Short circuit output current
Short-circuit
TYP
VO = 0,
ci
IOS
TLE2084Y
MIN
VO = 0,
• DALLAS, TEXAS 75265
pF
80
Ω
80
98
dB
82
99
dB
5.2
6.5
– 30
– 45
30
48
7.5
mA
mA
43
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
PARAMETER MEASUREMENT INFORMATION
2 kΩ
10 kΩ
VCC +
VCC +
2 kΩ
VI
–
+
VCC +
100 Ω
VI
VO
–
+
VO
VCC +
CL†
RL
CL†
RL
† Includes fixture capacitance
† Includes fixture capacitance
Figure 1. Slew-Rate Test Circuit
Figure 2. Unity-Gain Bandwidth
and Phase-Margin Test Circuit
† Includes fixture capacitance
2 kΩ
VCC +
Ground Shield
–
+
RS
RS
VCC +
–
+
VO
VO
VCC –
Picoammeters
VCC –
Figure 3. Noise-Voltage Test Circuit
Figure 4. Input-Bias and OffsetCurrent Test Circuit
VCC +
IN –
IN +
Cic
–
+
Cid
Cic
VO
VCC –
Figure 5. Internal Input Capacitance
typical values
Typical values presented in this data sheet represent the median (50% point) of device parametric performance.
input bias and offset current
At the picoampere bias-current level typical of the TLE208x and TLE208xA, accurate measurement of the bias
becomes difficult. Not only does this measurement require a picoammeter, but test socket leakages can easily
exceed the actual device bias currents. To accurately measure these small currents, Texas Instruments uses
a two-step process. The socket leakage is measured using picoammeters with bias voltages applied but with
no device in the socket. The device is then inserted in the socket and a second test is performed that measures
both the socket leakage and the device input bias current. The two measurements are then subtracted
algebraically to determine the bias current of the device.
44
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO
Input offset voltage
Distribution
6, 7, 8
αVIO
Input offset voltage temperature coefficient
Distribution
9, 10, 11
IIO
Input offset current
vs Free-air temperature
12 – 15
IIB
Input bias current
vs Free-air temperature
vs Supply voltage
12 – 15
16
VICR
VID
Common-mode input voltage range
vs Free-air temperature
Differential input voltage
vs Output voltage
18, 19
VOM +
Maximum positive peak output voltage
g
vs Output current
vs Free-air temperature
vs Supply voltage
20,, 21
24, 25
26
VOM –
Maximum negative
g
peak output voltage
g
vs Output current
vs Free-air temperature
vs Supply voltage
22,, 23
24, 25
26
VO(PP)
Maximum peak-to-peak output voltage
vs Frequency
27
VO
Output voltage
vs Settling time
28
AVD
Large signal differential voltage amplification
Large-signal
vs Load resistance
vs Free-air temperature
29
30, 31
AVD
Small-signal differential voltage amplification
vs Frequency
32, 33
CMRR
Common mode rejection ratio
Common-mode
vs Frequency
q
y
vs Free-air temperature
34
35
kSVR
Supply voltage rejection ratio
Supply-voltage
vs Frequency
q
y
vs Free-air temperature
36
37
ICC
Supply
y current
vs Supplyy voltage
g
vs Free-air temperature
vs Differential input voltage
IOS
Short-circuit output current
vs Supplyy voltage
g
vs Elapsed time
vs Free-air temperature
SR
Slew rate
vs Free-air temperature
vs Load resistance
vs Differential input voltage
Vn
Equivalent input noise voltage
vs Frequency
57
Input referred noise voltage
Input-referred
vs Noise bandwidth frequency
q
y
Over a 10-second time interval
58
59
Third-octave spectral noise density
vs Frequency bands
60
THD + N
Total harmonic distortion plus noise
vs Frequency
B1
Unity-gain bandwidth
vs Load capacitance
63
Gain bandwidth product
Gain-bandwidth
vs Free-air temperature
vs Supply voltage
64
65
Gain margin
vs Load capacitance
66
Phase margin
g
vs Free-air temperature
vs Supply voltage
vs Load capacitance
67
68
69
Phase shift
vs Frequency
Vn
φm
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
38,, 39,, 40
41, 42, 43
44 – 49
50
51
52
53,, 54
55
56
61, 62
32, 33
45
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS
Table of Graphs (Continued)
FIGURE
Noninverting large-signal pulse response
vs Time
70
Small-signal pulse response
vs Time
71
zo
Closed-loop output impedance
vs Frequency
72
ax
Crosstalk attenuation
vs Frequency
73
DISTRIBUTION OF TLE2082
INPUT OFFSET VOLTAGE
DISTRIBUTION OF TLE2081
INPUT OFFSET VOLTAGE
30
27
20
VCC = ± 15 V
TA = 25°C
P Package
18
16
Percentage of Units – %
Percentage of Units – %
24
21
18
15
12
9
14
12
10
8
6
4
6
2
3
0
–4
600 Units Tested From One Wafer Lot
VCC = ± 15 V
TA = 25°C
P Package
– 2.4
– 0.8
0.8
2.4
4
0
– 4 – 3.2 – 2.4 – 1.6 – 0.8 0
VIO – Input Offset Voltage – mV
Figure 6
46
Figure 7
POST OFFICE BOX 655303
0.8 1.6
2.4 3.2
VIO
V IO – Input Offset Voltage – mV
• DALLAS, TEXAS 75265
4
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS
DISTRIBUTION OF TLE2084
INPUT OFFSET VOLTAGE
50
DISTRIBUTION OF TLE2081 INPUT OFFSET
VOLTAGE TEMPERATURE COEFFICIENT
VCC± = ± 15 V
TA = 25°C
N Package
45
30
Percentage of Amplifiers – %
40
Percentage of Units – %
VCC = ± 15 V
TA = – 55 °C to 125°C
P Package
27
35
30
25
20
15
10
5
24
21
18
15
12
9
6
3
0
–8
– 4.8
– 1.6
4.8
1.6
0
– 40 – 32 – 24 –16 – 8
8
VIO
V IO – Input Offset Voltage – mV
24
32
40
DISTRIBUTION OF TLE2084 INPUT OFFSET
VOLTAGE TEMPERATURE COEFFICIENT
30
310 Amplifiers
VCC = ± 15 V
TA = – 55°C to 125°C
P Package
27
Percentage of Amplifiers – %
Percentage of Amplifiers – %
24
16
Figure 9
DISTRIBUTION OF TLE2082 INPUT OFFSET
VOLTAGE TEMPERATURE COEFFICIENT
27
8
αVIO – Temperature Coefficient – µV/°C
Figure 8
30
0
21
18
15
12
9
6
VCC± = ± 15 V
TA = – 55°C to 125°C
N Package
24
21
18
15
12
9
6
3
3
0
– 30 – 24 –18 –12 – 6
0
6
12
18
24
30
αVIO – Temperature Coefficient – µV/°C
0
– 40 – 32 – 24 –16 – 8
0
8
16
24
32
40
αVIO – Temperature Coefficient – µV/°C
Figure 11
Figure 10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
47
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081 AND TLE2082
INPUT BIAS CURRENT AND INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
TLE2084
INPUT BIAS CURRENT AND INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
100
10
I IO – Input Bias and Offset Currents – nA
IIB
I IB and IIO
I IO – Input Bias and Input Offset Currents – nA
IIIB
IB and IIO
TYPICAL CHARACTERISTICS†
VCC ± = ± 5 V
VIC = 0
VO = 0
1
IIO
0.1
IIB
0.01
0.001
– 75 – 55 – 35 – 15 – 5
25
45
65
85 105 125
100
10
VCC ± = ± 5 V
VIC = 0
VO = 0
1
IIB
IIO
0.1
0.01
0.001
– 75 – 55 – 35 – 15 – 5
TA – Free-Air Temperature – °C
100
VCC ± = ± 15 V
VIC = 0
VO = 0
IIB
1
0.1
IIO
0.01
5
25
65
85 105 125
45
65
85 105 125
TLE2084
INPUT BIAS CURRENT AND INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
I IO – Input Bias and Offset Currents – nA
IIIB
IB and IIO
I IO – Input Bias and Input Offset Currents – nA
IIIB
IB and IIO
TLE2081 AND TLE2082
INPUT BIAS CURRENT AND INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
0.001
– 75 – 55 – 35 – 15
45
Figure 13
Figure 12
10
25
TA – Free-Air Temperature – °C
100
10
VCC ± = ± 15 V
VIC = 0
VO = 0
IIB
1
0.1
IIO
0.01
0.001
– 75 – 55 – 35 – 15
TA – Free-Air Temperature – °C
5
25
45
65
85 105 125
TA – Free-Air Temperature – °C
Figure 14
Figure 15
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
48
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS†
INPUT BIAS CURRENT
vs
TOTAL SUPPLY VOLTAGE
COMMON-MODE INPUT VOLTAGE RANGE
vs
FREE-AIR TEMPERATURE
10 6
VCC + + 0.5
IIIB
IB – Input Bias Current – pA
10 5
VIC – Common-Mode Input Voltage Range – V
VIC
VICmax = VCC +
TA = 125°C
VICmin
10 4
10 3
10 2
TA = 25°C
10 1
TA = – 55°C
RS = 50 Ω
VCC +
VICmax
VCC + – 0.5
VCC – + 3.5
VICmin
VCC – + 3
VCC – + 2.5
10 0
0
5
10
15
20
25
30
35
40
VCC – + 2
– 75 – 55 – 35 – 15
45
Figure 16
200
RL = 600 Ω
RL = 2 kΩ
RL = 10 kΩ
– 100
RL = 2 kΩ
– 200
– 400
–5 –4
RL = 600 Ω
–3
– 2 – 10
VCC ± = ± 15 V
VIC = 0
RS = 50 Ω
TA = 25°C
300
RL = 10 kΩ
– 300
65
85 105 125
400
VCC ± = ± 5 V
VIC = 0
RS = 50 Ω
TA = 25°C
100
0
45
DIFFERENTIAL INPUT VOLTAGE
vs
OUTPUT VOLTAGE
V
VID
ID – Differential Input Voltage – uV
µV
V
VID
ID – Differential Input Voltage – uV
µV
300
25
Figure 17
DIFFERENTIAL INPUT VOLTAGE
vs
OUTPUT VOLTAGE
400
5
TA – Free-Air Temperature – °C
VCC – Total Supply Voltage (referred to VCC – ) – V
0
1
2
3
4
5
200
RL = 600 Ω
RL = 2 kΩ
100
0
RL = 10 kΩ
RL = 10 kΩ
– 100
RL = 2 kΩ
– 200
RL = 600 Ω
– 300
– 400
– 15
– 10
VO – Output Voltage – V
–5
0
5
10
15
VO – Output Voltage – V
Figure 18
Figure 19
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
49
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS†
15
13.5
12
TA = – 55°C
10.5
9
7.5
TA = 25°C
6
TA = 125°C
4.5
TA = 85°C
3
VCC ± = ± 15 V
1.5
0
0
TLE2084
MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE
vs
OUTPUT CURRENT
VVOM
OM+ – Maximum Positive Peak Output Voltage – V
VVOM
OM+ – Maximum Positive Peak Output Voltage – V
TLE2081 AND TLE2082
MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE
vs
OUTPUT CURRENT
15
12
TA = 25°C
9
6
3
VCC ± = ± 15 V
0
– 5 –10 –15 – 20 – 25 – 30 – 35 – 40 – 45 – 50
0
– 10
IO – Output Current – mA
– 20
–13.5
TA = – 55°C
–12
–10.5
TA = 25°C
–9
–7.5
–6
TA = 85°C
– 4.5
TA = 125°C
–3
VCC ± = ± 15 V
0
10
15
20
25
– 50
30
35
40
45
50
TLE2084
MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE
vs
OUTPUT CURRENT
V OM – – Maximum Negative Peak Output Voltage – V
V OM – – Maximum Negative Peak Output Voltage – V
–15
5
– 40
Figure 21
TLE2081 AND TLE2082
MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE
vs
OUTPUT CURRENT
0
– 30
IO – Output Current – mA
Figure 20
–1.5
TA = 85°C
TA = 125°C
–15
TA = – 55°C
–12
TA = 125°C
TA = 85°C
–9
TA = 25°C
–6
–3
VCC ± = ± 15 V
0
0
IO – Output Current – mA
10
20
30
40
50
IO – Output Current – mA
Figure 22
Figure 23
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
50
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS†
MAXIMUM PEAK OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
15
IO = – 200 µA
| V OM | – Maximum Peak Output Voltage – V
VOM – Maximum Peak Output Voltage – V
V
OM
5
4
IO = – 2 mA
3
2
IO = – 20 mA
1
VCC ± = ± 5 V
0
–1
IO = 20 mA
–2
–3
IO = 2 mA
–4
–5
– 75 – 55 – 35 –15
MAXIMUM PEAK OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
IO = 200 µA
5
25
45
65
14
IO = 2 mA
IO = – 2 mA
13.5
13
IO = 20 mA
12.5
IO = – 20 mA
12
11.5
11
VCC ± = ± 15 V
10.5
10
– 75 – 55 – 35 –15
85 105 125
TA – Free-Air Temperature – °C
VOM
VOM – Maximum Peak Output Voltage – V
TA = 25°C
20
IO = – 200 µA
IO = – 2 mA
IO = – 20 mA
0
IO = 20 mA
–5
–10
IO = 2 mA
IO = 200 µA
–15
– 20
– 25
0
2.5
5
7.5
45
65
85 105 125
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
vs
FREQUENCY
10 12.5 15 17.5 20 22.5 25
V O(PP) – Maximum Peak-to-Peak Output Voltage – V
VO(PP)
25
5
25
Figure 25
MAXIMUM PEAK OUTPUT VOLTAGE
vs
SUPPLY VOLTAGE
10
5
TA – Free-Air Temperature – °C
Figure 24
15
IO = 200 µA
IO = – 200 µA
14.5
30
VCC ± = ± 15 V
TA = 25°C,
125°C
RL = 2 kΩ
25
20
TA = – 55°C
15
TA = 25°C,
125°C
10
VCC ± = ± 5 V
5
0
100 k
|VCC ± | – Supply Voltage – V
Figure 26
TA = – 55°C
1M
f – Frequency – Hz
10 M
Figure 27
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
51
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS†
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
vs
LOAD RESISTANCE
OUTPUT VOLTAGE
vs
SETTLING TIME
125
12.5
10
10 mV
120
AVD
A
VD – Large-Signal Differential
Voltage Amplification – dB
VO
VO – Output Voltage – V
7.5
1 mV
5
2.5
VCC ± = ± 15 V
RL = 1 kΩ
CL = 100 pF
AV = – 1
TA = 25°C
Rising
0
Falling
– 2.5
–5
– 7.5
115
110
10 mV
– 10
0.5
1
1.5
2
VCC ± = ± 5 V
100
95
90
0.1
– 12.5
0
VCC ± = ± 15 V
105
ÁÁ
ÁÁ
1 mV
VIC = 0
RS = 50 Ω
TA = 25°C
ts – Settling Time – µs
1
10
Figure 29
Figure 28
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
vs
FREE-AIR TEMPERATURE
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
vs
FREE-AIR TEMPERATURE
110
125
107
121
VCC ± = ± 15 V
VO = ± 10 V
RL = 10 kΩ
ÁÁ
ÁÁ
AVD
A
VD – Large-Signal Differential
Voltage Amplification – dB
AVD
A
VD – Large-Signal Differential
Voltage Amplification – dB
RL = 10 kΩ
104
101
RL = 2 kΩ
98
95
92
RL = 600 Ω
ÁÁ
ÁÁ
89
86
83
VCC ± = ± 5 V
VO = ± 2.3 V
80
– 75 – 55 – 35 –15
5
25
100
RL – Load Resistance – kΩ
45
65
85 105 125
117
113
RL = 2 kΩ
109
105
101
97
RL = 600 Ω
93
89
85
– 75 – 55 – 35 –15
TA – Free-Air Temperature – °C
5
25
45
65
85 105 125
TA – Free-Air Temperature – °C
Figure 30
Figure 31
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
52
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS
SMALL-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE SHIFT
vs
FREQUENCY
140
Gain
20°
40°
80
60°
Phase Shift
60
80°
40
100°
20
120°
0
140°
– 20
160°
Phase Shift
AVD – Small-Signal Differential
Voltage Amplification – dB
120
100
0°
VCC ± = ± 15 V
RL = 2 kΩ
CL = 100 pF
TA = 25°C
180°
– 40
1
10
100
1k
10 k 100 k 1 M
10 M 100 M
f – Frequency – Hz
Figure 32
SMALL-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE SHIFT
vs
FREQUENCY
30
80°
Phase Shift
100°
CL = 25 pF
10
120°
Gain
0
140°
Phase Shift
AVD – Small-Signal Differential
Voltage Amplification – dB
CL = 100 pF
20
CL = 100 pF
VCC ± = ± 15 V
VIC = 0
RC = 2 kΩ
TA = 25°C
– 10
CL = 25 pF
160°
– 20
1
4
10
40
180°
100
f – Frequency – MHz
Figure 33
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
53
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS†
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
COMMON-MODE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
100
CMRR – Common-Mode Rejection Ratio – dB
CMRR – Common-Mode Rejection Ratio – dB
100
VCC ± = ± 15 V
90
VCC ± = ± 5 V
80
70
60
50
40
30
VIC = 0
VO = 0
RS = 50 Ω
TA = 25°C
20
10
0
10
100
1k
10 k
100 k
1M
97
VCC ± = ± 15 V
94
91
88
VCC ± = ± 5 V
85
82
79
76
73
VIC = VICRmin
VO = 0
RS = 50 Ω
70
– 75 – 55 – 35 –15
10 M
Figure 34
kXXXX
SVR – Supply-Voltage Rejection Ratio – dB
kXXXX
SVR – Supply-Voltage Rejection Ratio – dB
65
85 105 125
120
kSVR +
100
80
60
kSVR –
40
– 20
10
45
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
120
0
25
Figure 35
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREQUENCY
20
5
TA – Free-Air Temperature – °C
f – Frequency – Hz
∆ VCC ± = ± 5 V to ± 15 V
VIC = 0
VO = 0
RS = 50 Ω
TA = 25°C
100
1k
10 k
100 k
1M
10 M
114
kSVR +
108
102
96
90
kSVR –
84
78
72
66
∆ VCC ± = ± 5 V to ± 15 V
VIC = 0
VO = 0
RS = 50 Ω
60
– 75 – 55 – 35 –15
5
25
45
65
85 105 125
TA – Free-Air Temperature – °C
f – Frequency – Hz
Figure 36
Figure 37
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
54
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS†
TLE2082
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
TLE2081
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
4
4
VIC = 0
VO = 0
No Load
3.6
3.6
2.8
IICC
CC – Supply Current – mA
3.2
IICC
CC – Supply Current – mA
VIC = 0
VO = 0
No Load
3.8
TA = 25°C
2.4
TA = 125°C
2
1.6
TA = – 55°C
1.2
3.4
TA = 125°C
3.2
3
TA = 25°C
2.8
2.6
0.8
2.4
0.4
2.2
TA = – 55°C
2
0
0
2
4
6
8
10
12
14
16
18
0
20
2.5
5
|VCC ±| – Supply Voltage – V
Figure 38
10 12.5 15 17.5 20 22.5 25
Figure 39
TLE2081
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
TLE2084
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
4
10
VIC = 0
VO = 0
No Load
3.6
TA = 125°C
6
TA = 25°C
TA = – 55°C
VIC = 0
VO = 0
No Load
3.2
IICC
CC – Supply Current – mA
8
IICC
CC – Supply Current – mA
7.5
|VCC ±| – Supply Voltage – V
4
2.8
2.4
VCC ± = ± 15 V
2
1.6
VCC ± = ± 5 V
1.2
0.8
2
0.4
0
0
2
4
6
8
10
12
14
16
18
20
0
– 75 – 55 – 35 – 15 5
25
45
65
85 105 125
TA – Free-Air Temperature – °C
|VCC ±| – Supply Voltage – V
Figure 40
Figure 41
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
55
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS†
TLE2082
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
TLE2084
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
10
3.5
3.4
VIC = 0
VO = 0
No Load
VIC = 0
VO = 0
No Load
9
3.2
IICC
CC – Supply Current – mA
IICC
CC – Supply Current – mA
3.3
VCC ± = ± 15 V
3.1
3
2.9
VCC ± = ± 5 V
2.8
8
7
VCC ± = ± 15 V
VCC ± = ± 5 V
6
2.7
2.6
2.5
– 75 – 55 – 35 –15
5
25
45
65
5
–75 – 55 – 35 –15
85 105 125
TA – Free-Air Temperature – °C
Figure 42
45
65
85 105 125
TLE2082
SUPPLY CURRENT
vs
DIFFERENTIAL INPUT VOLTAGE
12
14
VCC + = 5 V
VCC – = 0
VIC = + 4.5 V
TA = 25°C
Open Loop
No Load
8
VCC + = 5 V
VCC – = 0
VIC = 4.5 V
TA = 25°C
Open Loop
No Load
12
IICC
CC – Supply Current – mA
10
IICC
CC – Supply Current – mA
25
Figure 43
TLE2081
SUPPLY CURRENT
vs
DIFFERENTIAL INPUT VOLTAGE
6
4
2
0
– 0.5
5
TA – Free-Air Temperature – °C
10
8
6
4
2
– 0.25
0
0.25
0.5
0
– 0.5
VID – Differential Input Voltage – V
– 0.25
0
0.25
VID – Differential Input Voltage – V
Figure 45
Figure 44
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
56
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
0.5
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS
TLE2081
SUPPLY CURRENT
vs
DIFFERENTIAL INPUT VOLTAGE
TLE2084
SUPPLY CURRENT
vs
DIFFERENTIAL INPUT VOLTAGE
25
20
VCC + = 5 V
VCC – = 0
VIC = 4.5 V
TA = 25°C
Open Loop
No Load
IICC
CC – Supply Current – mA
16
14
20
12
10
8
6
18
15
13
10
8
4
5
2
3
0
– 0.5
– 0.25
0
0.25
VID – Differential Input Voltage – V
VCC ± = ± 15 V
VIC = 0
TA = 25°C
Open Loop
No Load
23
IICC
CC – Supply Current – mA
18
0
–1.5
0.5
– 0.9
Figure 46
0.3
0
1.5
TLE2084
SUPPLY CURRENT
vs
DIFFERENTIAL INPUT VOLTAGE
40
25
VCC ± = ± 15 V
VIC = 0
TA = 25°C
Open Loop
No Load
VCC ± = ± 15 V
VIC = 0
TA = 25°C
Open Loop
No Load
36
32
IICC
CC – Supply Current – mA
20
0.9
Figure 47
TLE2082
SUPPLY CURRENT
vs
DIFFERENTIAL INPUT VOLTAGE
IICC
CC – Supply Current – mA
– 0.3
VID – Differential Input Voltage – V
15
10
28
24
20
16
12
8
5
4
0
–1.5
–1
– 0.5
0
0.5
1
1.5
VID – Differential Input Voltage – V
0
–1.5 –1.2 – 0.9 – 0.6 – 0.3 0
0.3
0.6 0.9
1.2
1.5
VID – Differential Input Voltage – V
Figure 48
Figure 49
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
57
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS†
SHORT-CIRCUIT OUTPUT CURRENT
vs
ELAPSED TIME
60
50
48
40
VID = – 1 V
36
24
12
VO = 0
TA = 25°C
0
–12
– 24
VID = 1 V
– 36
– 48
IIOS
OS – Short-Circuit Output Current – mA
IIOS
OS – Short-Circuit Output Current – mA
SHORT-CIRCUIT OUTPUT CURRENT
vs
SUPPLY VOLTAGE
VID = – 1 V
30
20
10
VCC ± = ± 15 V
VO = 0
TA = 25°C
0
–10
– 20
– 30
VID = 1 V
– 40
– 50
– 60
0
2.5
5
7.5
10 12.5 15 17.5 20 22.5 25
0
60
|VCC ± | – Supply Voltage – V
SHORT-CIRCUIT OUTPUT CURRENT
vs
FREE-AIR TEMPERATURE
SLEW RATE
vs
FREE-AIR TEMPERATURE
45
48
43
VCC ± = ± 15 V
32
VCC ± = ± 5 V
16
0
– 16
VCC ± = ± 5 V
VID = 1 V
– 32
VCC ± = ± 15 V
– 48
– 64
41
SR – Slew Rate – V/xs
V/µ s
IIOS
OS – Short-Circuit Output Current – mA
80
VID = – 1 V
180
Figure 51
Figure 50
64
120
t – Elapsed Time – s
VCC ± = ± 5 V
RL = 2 kΩ
CL = 100 pF
39
SR –
37
35
SR +
33
31
29
27
VO = 0
– 80
– 75 – 55 – 35 –15
5
25
45
65
85 105 125
25
– 75 – 55 – 35 –15
TA – Free-Air Temperature – °C
5
25
45
65
85 105 125
TA – Free-Air Temperature – °C
Figure 52
Figure 53
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
58
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS†
SLEW RATE
vs
LOAD RESISTANCE
SLEW RATE
vs
FREE-AIR TEMPERATURE
50
70
SR – Slew Rate – V/µ s
62
VCC ± = ± 15 V
RL = 2 kΩ
CL = 100 pF
Rising Edge
40
30
SR – Slew Rate – V/µ s
66
58
54
50
SR –
46
SR +
42
20
VCC ± = ± 5 V
VO ± = ± 2.5 V
10
0
–10
AV = – 1
CL = 100 pF
TA = 25°C
– 20
38
– 30
34
– 40
30
– 75 – 55 – 35 –15
Falling Edge
– 50
100
1k
5
25
45
65
85 105 125
TA – Free-Air Temperature – °C
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
50
Hz
AV = – 1
SR – Slew Rate – V/µ s
V n – Equivalent Input Noise Voltage – nV/
Vn
40
AV = 1
Rising Edge
20
VCC ± = ± 15 V
VO ± = ± 10 V (10% – 90%)
CL = 100 pF
TA = 25°C
10
0
–10
– 20
– 30
Falling Edge
AV = – 1
– 40
– 50
0.1
AV = 1
0.4
1
100 k
Figure 55
SLEW RATE
vs
DIFFERENTIAL INPUT VOLTAGE
30
10 k
RL – Load Resistance – Ω
Figure 54
50
VCC ± = ± 15 V
VO ± = ± 10 V
4
10
45
40
VCC ± = ± 15 V
VIC = 0
RS = 20 Ω
TA = 25°C
35
30
25
20
15
10
5
0
10
100
1k
10 k
f – Frequency – Hz
VID – Differential Input Voltage – V
Figure 56
Figure 57
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
59
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS
INPUT-REFERRED NOISE VOLTAGE
vs
NOISE BANDWIDTH FREQUENCY
1.2
VCC ± = ± 15 V
VIC = 0
RS = 20 Ω
TA = 25°C
10
Vn – Input-Referred Noise Voltage – µV
Vn
Vn – Input-Referred Noise Voltage – µV
Vn
100
INPUT-REFERRED NOISE VOLTAGE
OVER A 10-SECOND TIME INTERVAL
Peak-to-Peak
1
RMS
0.1
0.01
1
10
100
1k
10 k
0.9
0.6
0.3
0
– 0.3
– 0.6
0
100 k
VCC ± = ± 15 V
f = 0.1 to 10 Hz
TA = 25°C
1
2
THIRD-OCTAVE SPECTRAL NOISE DENSITY
vs
FREQUENCY BANDS
Start Frequency: 12.5 Hz
Stop Frequency: 20 kHz
VCC ± = ± 15 V
VIC = 0
TA = 25°C
– 90
– 95
–100
–105
–110
–115
10
15
20
25
30
6
7
8
9
10
35
40
45
1
AV = 100, RL = 600 Ω
0.1
AV = 100, RL = 2 kΩ
AV = 10, RL = 600 Ω
0.01
AV = 10, RL = 2 kΩ
VCC ± = ± 5 V
VO(PP) = 5 V
TA = 25°C
Filter: 10-Hz to 500-kHz Band Pass
0.001
10
Frequency Bands
100
1k
f – Frequency – Hz
Figure 60
60
5
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
FREQUENCY
THD + N – Total Harmonic Distortion + Noise – %
Third-Octave Spectral Noise Density – dB
– 75
– 85
4
Figure 59
Figure 58
– 80
3
t – Time – s
Noise Bandwidth Frequency – Hz
Figure 61
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
10 k
100 k
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS†
UNITY-GAIN BANDWIDTH
vs
LOAD CAPACITANCE
1
13
Filter: 10-Hz to 500-kHz Band Pass
VCC ± = ± 15 V
VO(PP) = 20 V
TA = 25°C
0.1
B1
B1 – Unity-Gain Bandwidth – MHz
THD + N – Total Harmonic Distortion + Noise – %
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
FREQUENCY
AV = 100, RL = 600 Ω
AV = 100, RL = 2 kΩ
0.01
AV = 10, RL = 600 Ω
AV = 10, RL = 2 kΩ
0.001
10
VCC ± = ± 15 V
VIC = 0
VO = 0
RL = 2 kΩ
TA = 25°C
12
11
10
9
8
7
100
1k
10 k
100 k
0
20
f – Frequency – Hz
40
Figure 62
100
GAIN-BANDWIDTH PRODUCT
vs
SUPPLY VOLTAGE
13
13
f = 100 kHz
VIC = 0
VO = 0
RL = 2 kΩ
CL = 100 pF
12
11
VCC ± = ± 15 V
10
VCC ± = ± 5 V
8
7
– 75 – 55 – 35 – 15
Gain-Bandwidth Product – MHz
Gain-Bandwidth Product – MHz
80
Figure 63
GAIN-BANDWIDTH PRODUCT
vs
FREE-AIR TEMPERATURE
9
60
CL – Load Capacitance – pF
f = 100 kHz
VIC = 0
VO = 0
RL = 2 kΩ
CL = 100 pF
TA = 25°C
12
11
10
9
8
7
5
25
45
65
85 105 125
0
5
TA – Free-Air Temperature – °C
10
15
20
25
|VCC
VCC +± | – Supply Voltage – V
Figure 64
Figure 65
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
61
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS†
PHASE MARGIN
vs
FREE-AIR TEMPERATURE
GAIN MARGIN
vs
LOAD CAPACITANCE
10
80°
VIC = 0
VO = 0
RL = 2 kΩ
70°
xm
φ m – Phase Margin
8
Gain Margin – dB
90°
VCC ± = ± 15 V
VIC = 0
VO = 0
RL = 2 kΩ
TA = 25°C
6
4
VCC ± = ± 15 V
CL = 25 pF
60°
VCC ± = ± 5 V
50°
VCC ± = ± 15 V
40°
30°
CL = 100 pF
VCC ± = ± 5 V
20°
2
10°
0°
–75 – 55 – 35 –15
0
0
20
40
60
80
100
25
45
65
85 105 125
TA – Free-Air Temperature – °C
CL – Load Capacitance – pF
Figure 67
Figure 66
PHASE MARGIN
vs
SUPPLY VOLTAGE
PHASE MARGIN
vs
LOAD CAPACITANCE
90°
90°
80°
80°
70°
70°
CL = 25 pF
60°
xm
φ m – Phase Margin
xm
φ m – Phase Margin
5
50°
CL = 100 pF
40°
30°
VIC = 0
VO = 0
RL = 2 kΩ
TA = 25°C
20°
10°
60°
VCC ± = ± 15 V
50°
VCC ± = ± 5 V
40°
30°
VIC = 0
VO = 0
RL = 2 kΩ
TA = 25°C
20°
10°
0°
0°
0
4
8
12
16
20
0
|VCC ±| – Supply Voltage – V
20
40
60
80
100
CL – Load Capacitance – pF
Figure 68
Figure 69
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
62
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TYPICAL CHARACTERISTICS†
NONINVERTING LARGE-SIGNAL
PULSE RESPONSE
SMALL-SIGNAL PULSE RESPONSE
100
15
TA = 25°C,
125°C
VO
VO – Output Voltage – mV
10
VO
VO – Output Voltage – V
TA = – 55°C
5
TA = – 55°C
0
TA = 25°C,
125°C
–5
VCC ± = ± 15 V
AV = 1
RL = 2 kΩ
CL = 100 pF
– 10
– 15
50
0
VCC ± = ± 15 V
AV = – 1
RL = 2 kΩ
CL = 100 pF
TA = 25°C
– 50
–100
0
1
2
3
t – Time – µs
4
5
0
1.6
Figure 71
Figure 70
TLE2082 AND TLE2084
CROSSTALK ATTENUATION
vs
FREQUENCY
CLOSED-LOOP OUTPUT IMPEDANCE
vs
FREQUENCY
100
140
VCC ± = ± 15 V
TA = 25°C
10
aaxx – Crosstalk Attenuation – dB
z o – Closed-Loop Output Impedance – Ω
zo
X
1.2
0.4
0.8
t – Time – µs
AV = 100
1
AV = 10
0.1
AV = 1
0.01
0.001
10
100
1k
10 k
100 k
1M
10 M
120
100
80
60
40
20
10
VCC ± = ± 15 V
VIC = 0
RL = 2 kΩ
TA = 25°C
100
1k
10 k
100 k
f – Frequency – Hz
f – Frequency – Hz
Figure 73
Figure 72
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
63
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
APPLICATION INFORMATION
input characteristics
The TLE208x, TLE208xA, and TLE208xB are specified with a minimum and a maximum input voltage that if
exceeded at either input could cause the device to malfunction. Because of the extremely high input impedance
and resulting low bias current requirements, the TLE208x, TLE208xA, and TLE208xB are well suited for
low-level signal processing; however, leakage currents on printed-circuit boards and sockets can easily exceed
bias current requirements and cause degradation in system performance. It is good practice to include guard
rings around inputs (see Figure 74). These guards should be driven from a low-impedance source at the same
voltage level as the common-mode input.
+
VI
VI
VO
+
+
VO
–
–
R2
R1
VO
VI
–
R3
R4
Where
R3
R4
+ R2
R1
Figure 74. Use of Guard Rings
TLE2081 input offset voltage nulling
The TLE2061 series offers external null pins that can be used to further reduce the input offset voltage. The
circuit of Figure 75 can be connected as shown if the feature is desired. When external nulling is not needed,
the null pins may be left unconnected.
IN –
–
OUT
IN +
N2
+
N1
100 kΩ
5 kΩ
VCC –
Figure 75. Input Offset Voltage Nulling
64
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
APPLICATION INFORMATION
macromodel information
Macromodel information provided was derived using PSpice Parts model generation software. The Boyle
macromodel (see Note 4) and subcircuit in Figure 58 were generated using the TLE208x typical electrical and
operating characteristics at TA = 25°C. Using this information, output simulations of the following key parameters
can be generated to a tolerance of 20% (in most cases):
D
D
D
D
D
D
D
D
D
D
D
D
Maximum positive output voltage swing
Maximum negative output voltage swing
Slew rate
Quiescent power dissipation
Input bias current
Open-loop voltage amplification
Unity-gain frequency
Common-mode rejection ratio
Phase margin
DC output resistance
AC output resistance
Short-circuit output current limit
NOTE 4: G.R. Boyle, B.M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers”, IEEE Journal
of Solid-State Circuits, SC-9, 353 (1974).
99
3
VCC +
EGND +
9
RSS
+
ISS
92
FB
10
IN –
J1
DP
VC
J2
IN+
11
DC
12
R2
–
53
HLIM
–
+
C2
6
VCC –
54
4
–
–
–
–
+
VLN
+
GCM
GA
VLIM
8
RD2
91
+
VLP
7
C1
RD1
+ DLP
90
RO2
VB
RP
2
1
–
DLN
–
RO1
DE
5
+
VE
OUT
.SUBCKT TLE208x 1 2 3 4 5
C1 11 12
2.2E–12
C2
6
7
10.00E–12
DC 5 53
DX
DE 54 5
DX
DLP 90 91
DX
DLN 92 90
DX
DP 4
3
DX
EGND
99
0 POLY (2) (3,0) (4,0) 0 .5 .5
FB
7 99
POLY (5) VB VC VE VLP VLN 0
+ . . . . 5.607E6 –6E6 6E6 6E6 –6E6
GA 6
0
11 12 333.0E–6
GCM 0
6
10 99 7.43E–9
ISS 3 10
DC 400.0E–6
HLIM 90 0
VLIM 1K
J1
11 2
10 JX
J2
12 1
10 JX
R2
6
9
100.0E3
RD1 4 11
3.003E3
RD2 4 12
3.003E3
R01 8
5
80
R02 7 99
80
RP 3
4
27.30E3
RSS 10 99
500.0E3
VB
9
0
DC 0
VC 3 53
DC 2.20
VE 54 4
DC 2.20
VLIM 7
8
DC 0
VLP 91 0
DC 45
VLN 0 92
DC 45
.MODEL DX D (IS=800.0E–18)
.MODEL JX PJF (IS=15.00E–12 BETA=554.5E–6
+ VTO=–.6)
.ENDS
Figure 76. Boyle Macromodel and Subcircuit
PSpice and Parts are trademarks of MicroSim Corporation.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
65
PACKAGE OPTION ADDENDUM
www.ti.com
1-Jun-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
TLE2081ACD
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2081ACDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2081ACDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2081ACDRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2081ACP
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2081ACPE4
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2081AID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2081AIDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2081AIP
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2081AIPE4
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2081CD
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2081CDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2081CDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2081CDRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2081CP
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2081CPE4
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2081ID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2081IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2081IDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Addendum-Page 1
(3)
Samples
(Requires Login)
PACKAGE OPTION ADDENDUM
www.ti.com
1-Jun-2012
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
Samples
(Requires Login)
TLE2081IDRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
TLE2081IP
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2081IPE4
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2082ACD
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2082ACDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2082ACDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2082ACDRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
TLE2082ACP
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2082ACPE4
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2082AID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2082AIDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2082AIDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2082AIDRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2082AIP
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2082AIPE4
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2082AMFKB
NRND
LCCC
FK
20
1
TBD
POST-PLATE N / A for Pkg Type
TLE2082AMJGB
ACTIVE
CDIP
JG
8
1
TBD
A42
TLE2082AMP
OBSOLETE
PDIP
P
8
TBD
Call TI
TLE2082CD
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2082CDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2082CDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2082CDRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Addendum-Page 2
(3)
N / A for Pkg Type
Call TI
PACKAGE OPTION ADDENDUM
www.ti.com
1-Jun-2012
Orderable Device
Status
(1)
TLE2082CP
ACTIVE
TLE2082CPE4
ACTIVE
TLE2082ID
ACTIVE
TLE2082IDG4
ACTIVE
TLE2082IDR
Package Type Package
Drawing
PDIP
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
Samples
(Requires Login)
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2082IDRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2082IP
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
TLE2082IPE4
ACTIVE
PDIP
P
8
50
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2082MFKB
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE N / A for Pkg Type
TLE2082MJGB
OBSOLETE
CDIP
JG
8
TBD
Call TI
Call TI
TLE2082MP
OBSOLETE
PDIP
P
8
TBD
Call TI
Call TI
TLE2084ACDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2084ACDWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2084ACN
ACTIVE
PDIP
N
14
25
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2084ACNE4
ACTIVE
PDIP
N
14
25
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2084CDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2084CDWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2084CDWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLE2084CDWRG4
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU N / A for Pkg Type
TLE2084CN
ACTIVE
PDIP
N
14
25
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2084CNE4
ACTIVE
PDIP
N
14
25
Pb-Free (RoHS)
CU NIPDAU N / A for Pkg Type
TLE2084IDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
Addendum-Page 3
(3)
CU NIPDAU Level-1-260C-UNLIM
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
1-Jun-2012
Status
(1)
Package Type Package
Drawing
Pins
TLE2084IDWG4
ACTIVE
SOIC
DW
16
TLE2084IDWR
OBSOLETE
SOIC
DW
16
Package Qty
40
Eco Plan
(2)
Green (RoHS
& no Sb/Br)
TBD
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
CU NIPDAU Level-1-260C-UNLIM
Call TI
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TLE2082, TLE2082A, TLE2082AM, TLE2082M :
• Catalog: TLE2082A, TLE2082
• Military: TLE2082M, TLE2082AM
NOTE: Qualified Version Definitions:
Addendum-Page 4
PACKAGE OPTION ADDENDUM
www.ti.com
1-Jun-2012
• Catalog - TI's standard catalog product
• Military - QML certified for Military and Defense Applications
Addendum-Page 5
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TLE2081ACDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLE2081CDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLE2081IDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLE2081IDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLE2082ACDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLE2082AIDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLE2082AIDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLE2082CDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLE2082IDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLE2084CDWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TLE2081ACDR
SOIC
D
8
2500
340.5
338.1
20.6
TLE2081CDR
SOIC
D
8
2500
340.5
338.1
20.6
TLE2081IDR
SOIC
D
8
2500
340.5
338.1
20.6
TLE2081IDR
SOIC
D
8
2500
367.0
367.0
35.0
TLE2082ACDR
SOIC
D
8
2500
340.5
338.1
20.6
TLE2082AIDR
SOIC
D
8
2500
367.0
367.0
35.0
TLE2082AIDR
SOIC
D
8
2500
340.5
338.1
20.6
TLE2082CDR
SOIC
D
8
2500
340.5
338.1
20.6
TLE2082IDR
SOIC
D
8
2500
340.5
338.1
20.6
TLE2084CDWR
SOIC
DW
16
2000
367.0
367.0
38.0
Pack Materials-Page 2
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUARY 1997
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE
0.400 (10,16)
0.355 (9,00)
8
5
0.280 (7,11)
0.245 (6,22)
1
0.063 (1,60)
0.015 (0,38)
4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.130 (3,30) MIN
0.023 (0,58)
0.015 (0,38)
0°–15°
0.100 (2,54)
0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a ceramic lid using glass frit.
Index point is provided on cap for terminal identification.
Falls within MIL STD 1835 GDIP1-T8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated