Series AM3HW-NZ 3 Watt | DC-DC Converter Picture coming soon FEATURES: • • • • • • • • • • SMD Package Ultra-wide input range 4:1 High efficiency up to 84% Low ripple and noise Remote On/Off Control No load power consumption ≤0.12W Input to Output Isolation of 1500VDC Input under voltage lockout Over current and Short circuit protection Operating temperature of -40 to +85°C Models Single output Model Input Voltage (V) Max Input current full load (mA) Output Voltage (V) Output Current max (mA) Isolation (VDC) Max Capacitive Load (uF) Efficiency (%) AM3HW-2405S-NZ AM3HW-2412S-NZ AM3HW-2415S-NZ AM3HW-2424S-NZ AM3HW-4815S-NZ 9-36 9-36 9-36 9-36 18-75 173 173 173 173 81 5 12 15 24 15 600 250 200 125 200 1500 1500 1500 1500 1500 2200 680 470 100 470 80 82 83 82 84 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Voltage range Nominal Typical 24 48 Filter Start up time Absolute Maximum Rating 24 48 Units VDC ms -0.7 - 50 -0.7 - 100 1 ON – open or 3.5-12VDC ; OFF – short to –Vin or 0-1.2VDC, Idle current: 6-10mA 6 5 Peak Input Voltage time On/Off control No Load Input Current Maximum 9-36 18-75 Capacitor 10 24 48 Rise time VDC s mA ms Under voltage lockout Input reflected ripple current 24 48 24 48 6.5 15.5 120 60 Conditions Typical 60 sec, 1mA 500VDC Isolation 100KHz/0.1V 1500 >1000 1000 VDC mA Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance Maximum Units VDC MOhm pF Output Specifications Parameters Voltage accuracy Over current protection Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation Temperature coefficient www.aimtec.com F 051e R13 Conditions Full load, LL-HL 0% to 100% load Typical ±1 150 Continuous, hiccup Auto-recovery ±0.2 ±0.5 Tel: +1 514 620 2722 1 of 3 Maximum Units ±3 250 % % of Iout ±0.5 ±1 ±0.03 % of Vin % o %/ C Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM3HW-NZ 3 Watt | DC-DC Converter Output Specifications (continued) Parameters Conditions Ripple & Noise* Transient recovery time Transient recovery deviation Typical Maximum Units 300 ±3 120 500 ±5 mV p-p µs % Conditions Typical Maximum Units 100% load Derating above 71°C 350 20MHz Bandwidth, 5% to 100% load 25% load step change 25% load step change * 0-5% load up to 5% of Vout. General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature -40 to +85 -55 to +125 105 KHz o C o C o C Free air convection 95 % RH Black flame retardant heat proof plastic (UL94-V0) 3.5 g 0.76 x 0.71 x 0.4 inches 19.20 x 18.10 x 10.16 mm o >1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 C) Look at the SMD soldering profile: http://www.aimtec.com/rohs-soldering-profiles Environment Specification Test Parameters Test mode Acceleration Vibration Conditions 10-55Hz 10g, 30min, every axis tested Safety Specifications Parameters Meets IEC60950-1 Meet EN 55022, Class B, with external filter & EN 55024: 2010 IEC 61000-4-2, Contact ±4KV, Criteria B IEC 61000-4-3, 10V/m, Criteria A IEC 61000-4-4, ±2KV, Criteria B, with external filter IEC 61000-4-5, ±2KV, Criteria B, with external filter IEC 61000-4-6, 3Vrms, Criteria A IEC 61000-4-29, 0-70%, Criteria B Standards Derating Free Air Convection 71º C Output Power (%) 100 80 Safe Operating Area 60 40 20 0 - 40 - 20 0 20 40 60 80 85 100 Ambient Temperature º C www.aimtec.com F 051e R13 Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM3HW-NZ 3 Watt | DC-DC Converter Pin Out Specifications Dimensions Top View Pin 1 2 6 7 8 9 14 Single -Vin On/Off Control NC NC +Vout -Vout +Vin 19.20 (0.76) Side View 14 9 8 10.16 (0.40) 1.00 (0.04) 18.10 (0.71) 2.54 (0.10) 6 2 15.24 (0.60) 1.00 (0.04) All dimensions are in mm (inch) Pin tolerance: ±0.10 (±0.004) Case tolerance of ±0.50 (±0.02) 7 EMC recommended circuit: +Vin LDM 12µH F1 MOV -Vin C1 C2 C3 C5 C4 DC-DC Converter +Vo -Vo CY1 1nF/2KV Model MOV 24 Vin S14K35 48 Vin S14K60 C1 & C2 330 µF / 50V 330 µF / 100V C3 &C4 4.7 µF / 50V 4.7 µF / 100V C3 10 µF NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4 . All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R13 Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only