ASL360 Wideband Linear Amplifier MMIC Features Description 17.3 dB Gain at 500 MHz The ASL360, a wideband linear amplifier MMIC, has a high linearity and low noise over a wide range of frequency 5 MHz to 2.6 GHz, being suitable for use in the fiber receiver, distribution amplifiers and drop amplifiers of CATV systems, and in the mobile wireless repeaters and BTS. The amplifier is available in a SOT89 package and passes through the stringent DC, RF, and reliability tests. 21 dBm P1dB at 500 MHz 40 dBm Output IP3 at 500 MHz 1.6 dB NF at 500 MHz 75 Input & Output Match Bandwidth 5 ~ 1200 MHz Single Supply +5 V ASL360 Package Style: SOT89 Typical Performance (Supply Voltage = +5 V, TA = +25 C, Z0 = 75 ) Application Circuit Parameters Units Frequency MHz 5 50 500 860 1200 2150 Noise Figure dB 1.8 1.5 1.6 1.7 2.0 2.3 Gain dB 17.5 17.3 17.3 17.2 15.5 15.4 50 ~ 1200 MHz S11 dB -12 -17 -15 -15 -12 -10 5 ~ 200 MHz S22 dB -12 -17 -17 -15 -17 -8 Output P1dB dBm 21.0 21 21 17 20 17 Output IP3 dBm 41.51) 41.52) 40.02) 34.02) 38.53) 36.52) Output IP2 dBm 53 53 53 62 57 - 5) CSO dBc 60 CTB5) dBc 75 Current mA 110 Device Voltage V +5 1),2),3)4) Typical 50 ~ 1000 MHz 950 ~ 2150 MHz (SMATV) 50 ~ 1000 MHz (Push-Pull, 1:1 transformer) 50 ~ 1200 MHz (Push-Pull, 1:1 transformer) 5 ~ 200 MHz 1) OIP3 and OIP2 are measured with two tones at an output power of +8 dBm/tone separated by 1 MHz. 2) OIP3 and OIP2 are measured with two tones at an output power of +5 dBm/tone separated by 6 MHz. 3) OIP3 and OIP2 are measured with two tones at an output power of +6 dBm/tone separated by 6 MHz 4) OIP2 is measured at F1+F2 Frequency. 5) 60 channels, +33 dBmV per channel (measured at output). (Push-Pull, 1:1 transformer) 20 ~ 1000 MHz (50 Ω) Product Specifications (Push-Pull, 1:1 transformer) Parameters Units Testing Frequency MHz Min Typ. Gain dB 16.3 17.3 S11 dB -12 -15 S22 dB -15 -17 Output IP3 dBm 37 40 Noise Figure dB Output P1dB dBm 20 21 Current mA 95 110 Device Voltage V Max 500 1.6 1.8 125 +5 Absolute Maximum Ratings Parameters Rating Operating Case Temperature -40 to 85 C Storage Temperature -40 to 150 C Device Voltage +6 V Operating Junction Temperature +150 C Input RF Power (CW, 75 matched) +18 dBm Maximum Current 150 mA Thermal Resistance 43 C/W 1/12 ASB Inc. [email protected] Tel: +82-42-528-7225 September 2017 ASL360 Wideband Linear Amplifier MMIC Outline Drawing Part No. Lot No. Symbols A L b b1 C D D1 E E1 e1 H S e ASL360 Pxxxx Dimensions (In mm) MIN NOM 1.40 1.50 0.89 1.04 0.36 0.42 0.41 0.47 0.38 0.40 4.40 4.50 1.40 1.60 3.64 --2.40 2.50 2.90 3.00 0.35 0.40 0.65 0.75 1.40 1.50 Pin No. Function 1 RF IN 2 GND 3 RF OUT & Bias MAX 1.60 1.20 0.48 0.53 0.43 4.60 1.75 4.25 2.60 3.10 0.45 0.85 1.60 Mounting Recommendation (In mm) Note: 1. The number and size of ground via holes in a circuit board is critical for thermal and RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of the lead pin 2 and exposed pad of the device for better RF and thermal performance, as shown in the drawing at the left side. ESD Classification & Moisture Sensitivity Level ESD Classification HBM Class 1B Voltage Level: 550 V MM Class A Voltage Level: 50 V CAUTION: ESD-sensitive device! Moisture Sensitivity Level (MSL) Level 3 at 260 C reflow 2/12 ASB Inc. [email protected] Tel: +82-42-528-7225 September 2017 ASL360 Wideband Linear Amplifier MMIC APPLICATION CIRCUIT CATV Frequency (MHz) 50 500 860 Noise Figure (dB) 1.5 1.6 1.7 Magnitude S21 (dB) 17.3 17.3 17.2 Magnitude S11 (dB) -17 -15 -15 Magnitude S22 (dB) -17 -17 -15 Output P1dB (dBm) 21 21 17 Output IP3 (dBm) 41.5 40.0 34.0 Output IP21),2) (dBm) 53 53 62 1) 50 ~ 1000 MHz +5 V 3) CSO (dBc) 60 CTB3) (dBc) 75 Device Voltage (V) +5 Current (mA) 110 1) OIP3 and OIP2 are measured with two tones at an output power of +5 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. 3) 60 channels, +33 dBmV per channel (measured at output). Schematic Board Layout (FR4, 40x40 mm2, 0.8T) Note: Gain slope can be adjusted by L5 and R1 values at the expense of S11 & S22. S-parameters 25 0 20 -5 15 -10 10 S11 (dB) Gain (dB) o o -40 c o 25 c o 85 c 5 -40 c o 25 c o 85 c -15 -20 -25 0 0 100 200 300 400 500 600 700 800 900 1000 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Frequency (MHz) 0 o -40 c o 25 c o 85 c -5 S22 (dB) -10 -15 -20 -25 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) 3/12 ASB Inc. [email protected] Tel: +82-42-528-7225 September 2017 ASL360 Wideband Linear Amplifier MMIC Current vs. Temperature Gain vs. Temperature 22 200 20 18 Gain (dB) Current (mA) 150 100 16 50 Frequency = 860 MHz 14 0 -60 -40 -20 0 20 40 60 80 12 -60 100 -40 -20 0 20 40 60 80 100 o o Temperature ( C) Temperature ( C) P1dB vs. Temperature 30 25 P1dB (dBm) 20 15 10 Frequency = 860 MHz 5 0 -60 -40 -20 0 20 40 60 80 100 o Temperature ( C) Output IP3 vs. Tone Power (Frequency = 860 MHz) Output IP2 vs. Tone Power (Frequency = 860 MHz) 50 MHz) 90 45 80 40 70 Output IP2 (dBm) Output IP3 (dBm) 35 30 25 20 o -40 c o 25 c o 85 c 15 10 60 50 40 30 o -40 c o 25 c o 85 c 20 10 5 0 0 -1 0 1 2 3 4 5 6 7 8 9 10 11 -1 0 1 Pout per Tone (dBm) 4/12 2 3 4 5 6 7 8 9 10 11 Pout per Tone (dBm) ASB Inc. [email protected] Tel: +82-42-528-7225 September 2017 ASL360 Wideband Linear Amplifier MMIC APPLICATION CIRCUIT CATV 50 ~ 1200 MHz Frequency (MHz) 50 500 1200 Noise Figure (dB) 1.6 1.7 2.0 Magnitude S21 (dB) 16.8 17.0 15.8 Magnitude S11 (dB) -11 -12 -12 Magnitude S22 (dB) -17 -17 -11 Output P1dB (dBm) 20.5 20.0 20.0 Output IP3 (dBm) 39.0 38.5 38.5 Output IP21),2) (dBm) 53 57 50 Device Voltage (V) +5 Current (mA) 110 1) +5 V . 1) OIP3 and OIP2 are measured with two tones at an output power of +6 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency Board Layout (FR4, 40x40 mm2, 0.8T) Schematic 25 0 20 -5 15 -10 S11 (dB) Gain (dB) S-parameters 10 -20 5 0 -15 -25 0 200 400 600 800 1000 1200 1400 0 200 Frequency (MHz) 400 600 800 1000 1200 1400 Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 0 200 400 600 800 1000 1200 1400 Frequency (MHz) 5/12 ASB Inc. [email protected] Tel: +82-42-528-7225 September 2017 ASL360 Wideband Linear Amplifier MMIC APPLICATION CIRCUIT CATV 5 ~ 200 MHz Frequency (MHz) 5 50 200 Noise Figure (dB) 1.8 1.5 1.5 Magnitude S21 (dB) 17.5 17.5 17.5 Magnitude S11 (dB) -12 -20 -18 Magnitude S22 (dB) -12 -20 -15 Output P1dB (dBm) 21.0 21.0 21.0 Output IP3 (dBm) 41.5 40.5 43.0 Output IP21),2) (dBm) 53 56 57 Device Voltage (V) +5 Current (mA) 110 1) +5 V . 1) OIP3 and OIP2 are measured with two tones at an output power of +8 dBm/tone separated by 1 MHz. 2) OIP2 is measured at F1+F2 Frequency Board Layout (FR4, 40x40 mm2, 0.8T) Schematic S-parameters 25 0 20 15 S11 (dB) Gain (dB) -10 10 -20 -30 5 0 -40 0 50 100 150 200 250 300 0 Frequency (MHz) 50 100 150 200 250 300 Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 -30 0 50 100 150 200 250 300 Frequency (MHz) 6/12 ASB Inc. [email protected] Tel: +82-42-528-7225 September 2017 ASL360 Wideband Linear Amplifier MMIC Frequency (MHz) 950 1500 2150 Noise Figure (dB) 1.8 2.3 2.3 Magnitude S21 (dB) 17.3 16.6 15.4 Magnitude S11 (dB) -7 -8 -10 SMATV Magnitude S22 (dB) -12 -12 -8 950 ~ 2150 MHz Output P1dB (dBm) 18 17 17 Output IP3 (dBm) 34.5 37.0 36.5 Device Voltage (V) +5 Current (mA) 110 APPLICATION CIRCUIT 1) +5 V . 1) OIP3 is measured with two tones at an output power of +5 dBm/tone separated by 1 MHz. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic Vs=5 V C4=1 F L1=8.2 nH C1=100 pF RF IN C2=100 pF RF OUT ASL360 L2=12 nH C3=1 pF 20 0 15 -5 S11 (dB) Gain (dB) S-parameters 10 5 -10 -15 0 -20 0 500 1000 1500 2000 2500 0 Frequency (MHz) 500 1000 1500 2000 2500 Frequency (MHz) 0 S22 (dB) -5 -10 -15 -20 0 500 1000 1500 2000 2500 Frequency (MHz) 7/12 ASB Inc. [email protected] Tel: +82-42-528-7225 September 2017 ASL360 Wideband Linear Amplifier MMIC APPLICATION CIRCUIT CATV Push-Pull 1 : 1 transformer Frequency (MHz) 50 500 860 Magnitude S21 (dB) 11.3 11.3 11.3 Magnitude S11 (dB) -15 -14 -16 Magnitude S22 (dB) -15 -15 -16 Output P1dB (dBm) 23.0 24.5 24.5 Output IP31) (dBm) 39.0 44.0 41.5 1),2) 65 62 58 50 ~ 1000 MHz Output IP2 Noise Figure (dB) (dBm) 2.8 2.8 2.8 +5 V Device Voltage (V) +5 Current (mA) 220 . 1) OIP3 and OIP2 are measured with two tones at an output power of +10 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic Note: MABA-007159 1:1 impedance transformers are used. S-parameters 0 20 -5 -10 S11 (dB) Gain (dB) 15 10 -15 5 -20 0 -25 0 200 400 600 800 1000 0 200 400 600 800 1000 Frequency (MHz) Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 0 200 400 600 800 1000 Frequency (MHz) 8/12 ASB Inc. [email protected] Tel: +82-42-528-7225 September 2017 ASL360 Wideband Linear Amplifier MMIC APPLICATION CIRCUIT CATV Push-Pull 1 : 1 transformer Frequency (MHz) 50 500 1200 Magnitude S21 (dB) 11.4 11.2 11.3 Magnitude S11 (dB) -15 -13 -12 Magnitude S22 (dB) -15 -14 -13 Output P1dB (dBm) 23.0 25.0 25.0 Output IP31) (dBm) 39.0 44.0 41.5 1),2) 65 62 58 50 ~ 1200 MHz Output IP2 Noise Figure (dB) (dBm) 2.8 2.8 2.9 +5 V Device Voltage (V) +5 Current (mA) 220 . 1) OIP3 and OIP2 are measured with two tones at an output power of +8 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic Note: MABA-007159 1:1 impedance transformers are used. S-parameters 0 20 -5 -10 S11 (dB) Gain (dB) 15 10 -15 5 -20 0 -25 0 200 400 600 800 1000 1200 1400 0 200 400 600 800 1000 1200 1400 Frequency (MHz) Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 0 200 400 600 800 1000 1200 1400 Frequency (MHz) 9/12 ASB Inc. [email protected] Tel: +82-42-528-7225 September 2017 ASL360 Wideband Linear Amplifier MMIC APPLICATION CIRCUIT CATV Push-Pull 1 : 1 transformer Frequency (MHz) 5 50 200 Magnitude S21 (dB) 11.5 11.5 11.3 Magnitude S11 (dB) -16 -18 -16 Magnitude S22 (dB) -16 -18 -16 Output P1dB (dBm) 23.0 24.0 25.0 Output IP31) (dBm) 38.0 40.0 43.0 1),2) 62 63 68 5 ~ 200 MHz Output IP2 Noise Figure (dB) (dBm) 3.3 2.7 2.8 +5 V Device Voltage (V) +5 Current (mA) 220 . 1) OIP3 and OIP2 are measured with two tones at an output power of +7 dBm/tone separated by 1 MHz. 2) OIP2 is measured at F1+F2 Frequency. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic Note: MABA-007159 1:1 impedance transformers are used. S-parameters 0 20 -5 -10 S11 (dB) Gain (dB) 15 10 -15 5 -20 -25 0 0 50 100 150 200 250 300 0 50 0 100 150 200 250 300 Frequency (MHz) Frequency (MHz) -5 S22 (dB) -10 -15 -20 -25 -30 0 50 100 150 200 250 300 Frequency (MHz) 10/12 ASB Inc. [email protected] Tel: +82-42-528-7225 September 2017 ASL360 Wideband Linear Amplifier MMIC APPLICATION CIRCUIT Push-Pull 1 : 1 transformer Frequency (MHz) 20 400 800 1000 Magnitude S21 (dB) 10.0 10.0 10.0 10.0 Magnitude S11 (dB) -9 -17 -10 -10 Magnitude S22 (dB) -9 -18 -11 -11 Output P1dB (dBm) 24.0 24.0 24.0 23.5 Output IP31) (dBm) 42.0 44.0 44.5 44.0 1),2) 60 73 65 60 20 ~ 1000 MHz Output IP2 Noise Figure (dB) (dBm) 3.2 3.2 3.3 3.4 +5 V, 50 Ω Device Voltage (V) +5 Current (mA) 220 . 1) OIP3 and OIP2 are measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. 2) OIP2 is measured at F1+F2 Frequency. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic Note: MABA-007159 1:1 impedance transformers are used. S-parameters 0 20 -5 -10 S11 (dB) Gain (dB) 15 10 -15 5 -20 -25 0 0 100 200 300 400 500 600 700 800 900 1000 0 100 0 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Frequency (MHz) -5 S22 (dB) -10 -15 -20 -25 -30 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) 11/12 ASB Inc. [email protected] Tel: +82-42-528-7225 September 2017 ASL360 Wideband Linear Amplifier MMIC Recommended Soldering Reflow Profile 260 C Ramp-up (3 C/sec) 20~40 sec Ramp-down (6 C/sec) 200 C 150 C 60~180 sec Copyright 2010-2017 ASB Inc. All rights reserved. Datasheet subject to change without notice. ASB assumes no responsibility for any errors which may appear in this datasheet. No part of the datasheet may be copied or reproduced in any form or by any means without the prior written consent of ASB. 12/12 ASB Inc. [email protected] Tel: +82-42-528-7225 September 2017