TC7SB385FU TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC7SB385FU Single Bus Switch The TC7SB385FU provides single bit of high-speed TTL-compatible switching. The low on resistance of the switch allows connections to be made with minimal propagation delay. The device is organized as just 1-bit low-impedance switch with output-enable (OE) input. When OE is high, the switch is on and data can flow from port A to port B, or vice versa. When OE is low, the switch is open and a high-impedance state exists between the two ports. All inputs are equipped with protection circuits against static discharge. Weight: 0.006 g (typ.) Features • Operating voltage: VCC = 4.5~5.5 V • High speed operation: tpd = 0.25 ns (max) • Low on resistance: RON = 5 Ω (typ.) • ESD performance: Machine model ≥ ±200 V Human body model ≥ ±2000 V • TTL level input (control input) • Package: USV Pin Assignment (top view) VCC OE 4 5 JK 1 A 2 B 3 GND 1 2007-10-19 TC7SB385FU Truth Table Input Function OE L Disconnect H A port = B port System Diagram A B OE Absolute Maximum Ratings (Note) Characteristics Symbol Rating Unit Power supply range VCC −0.5~7.0 V DC input voltage VIN −0.5~7.0 V DC switch voltage VS −0.5~7.0 V Input diode current IIK −50 mA Continuous channel current IS 128 mA Power dissipation PD 200 mW DC VCC/GND current ICC/IGND ±100 mA Storage temperature Tstg −65~150 °C Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Operating Ranges (Note) Characteristics Symbol Rating Unit Supply voltage VCC 4.5~5.5 V Input voltage VIN 0~5.5 V Switch voltage VS 0~5.5 V Operating temperature Topr −40~85 °C Input rise and fall time dt/dv 0~10 ns/V Note: The operating ranges must be maintained to ensure the normal operation of the device. 2 2007-10-19 TC7SB385FU Electrical Characteristics DC Characteristics (Ta = −40~85°C) Characteristics Input voltage Min Typ. (Note 1) Max 4.5~5.5 2.0 ⎯ ⎯ 4.5~5.5 ⎯ ⎯ 0.8 4.5~5.5 ⎯ ⎯ ±1.0 μA 0 ⎯ ⎯ ±1.0 μA 4.5~5.5 ⎯ ⎯ ±1.0 μA IIS = 30 mA 4.5 ⎯ 5 7 IIS = 64 mA 4.5 ⎯ 5 7 VIS = 2.4 V, IIS = 15 mA 4.5 ⎯ 10 15 VIN = VCC or GND, IOUT = 0 5.5 ⎯ ⎯ 10 μA VIN = 3.4 V (one input) 5.5 ⎯ ⎯ 2.5 mA Symbol Test Condition “H” level VIH ⎯ “L” level VIL ⎯ Input leakage current IIN Power off leakage current Off-state leakage current (switch off) ON resistance (Note 2) Quiescent supply current IOFF ISZ RON ICC ΔICC VCC (V) VIN = 0~5.5 V A, B, OE = 0~5.5 V A, B = 0~5.5 V, OE = GND VIS = 0 V Unit V Ω Note 1: Typical values are at VCC = 5 V and Ta = 25°C. Note 2: Measured by the voltage drop between A and B pins at the indicated current through the switch. On resistance is determined by the lower of the voltages on the two (A or B) pins. AC Characteristics (Ta = −40~85°C) Characteristics Propagation delay time tpLH (bus to bus) tpHL Output enable time Output disable time Min Max Unit 4.5 ⎯ 0.25 ns Figure 1, Figure 3 4.5 ⎯ 4.0 ns Figure 1, Figure 3 4.5 ⎯ 5.0 ns Symbol tpZL tpZH tpLZ tpHZ Test Condition Figure 1, Figure 2 VCC (V) (Note) Note: This parameter is guaranteed by design but is not tested. The bus switch contributes no propagation delay other than the RC delay of the typical on resistance of the switch and the 50 pF load capacitance, when driven by an ideal voltage the source (zero output impedance). Capacitive Characteristics (Ta = 25°C) Characteristics Symbol Control pin input capacitance CIN Switch terminal capacitance CI/O Test Condition OE = GND VCC (V) Typ. Unit (Note) 5.0 3 pF (Note) 5.0 10 pF Note: This item is guaranteed by design. 3 2007-10-19 TC7SB385FU AC Test Circuit RL Switch Open 7.0 V GND Measure RL CL Output CL = 50 pF RL = 500 Ω Parameter Switch tpLH, tpHL Open tpLZ, tpZL 7.0 V tpHZ, tpZH Open Figure 1 AC Waveform tr 2.5 ns tf 2.5 ns 3.0 V 90% 1.5 V Input (A, B) 10% GND VOH Output (B, A) 1.5 V tpLH VOL tpHL Figure 2 tpLH, tpHL tf 2.5 ns tr 2.5 ns 3.0 V 90% 1.5 V Output Enable (OE) 10% tpLZ GND tpZL 3.5 V Output (A, B) Low to Off to Low 1.5 V tpHZ VOL + 0.3 V VOH − 0.3 V Output (A, B) High to Off to High VOL tpZH VOH 1.5 V GND Outputs enabled Outputs disabled Outputs enabled Figure 3 tpLZ, tpHZ, tpZL, tpZH 4 2007-10-19 TC7SB385FU Package Dimensions Weight: 0.006 g (typ.) 5 2007-10-19 TC7SB385FU RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 6 2007-10-19