MN103SB9 Series Type Internal ROM type MN103SB9N MN103SFB9R Mask ROM FLASH 512K ROM (byte) 1024K 32K RAM (byte) TQFP128-P-1414A Package (Lead-free) Minimum Instruction Execution Time 16.7 ns (at 2.7 V to 3.6 V, 60 MHz) Interrupts RESET. IRQ × 9. NMI. Timer × 28. I2C × 3. SIF × 10. DMA × 12. WDT. A/D. Time base timer × 2. System error Timer Counter 8-bit timer × 10 Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer) 16-bit timer × 6 Up-down count. Input capture. PWM output. Compare/capture register 2 channnels Time base timer × 1 Watchdog timer × 1 Serial interface UART/Synchronous/Multi-master I2C interface selective × 3 UART/Synchronous interface selective × 2 DMA controller Number of channels: 4 channels Unit of transfer: 8/16/32 bits Maximum transfer cycles: 65535 Starting factor: External interrupt. Timer. Serial transmission/reception. A/D conversion finish. I2C transmission/reception. External transmission request. Software Transfer method: 2-bus cycle transfer Adressing modes: Fixed. Increment. Decrement Transfer mode: Word transfer. Burst transfer. Intermittent transfer Extended Calculation Multiply and accumulate arithmetic. Multiplication. Saturated arithmetic I/O Pins I/O 104 : Common use A/D converter 10-bit × 12 channels ROM Correction 8 channels Electrical Charactreistics (A/D converter characteristics) Parameter Resolution Non-linear error Differential non-linearity error Symbol Condition AVDD = 3.3 V. VSS = 0 V min Limit typ max 10 ±4 ±4 Unit Bits LSB LSB MAF00023DEM MN103SB9N, MN103SFB9R Pin Assignment 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 PD6 P00, NMIRQ P01, IRQ8 P02, SBI3 P03, SBO3 P04, SBT3 P05, SBI2 P06, SBO2, SDA2 P07, SBT2, SCL2 OCD_SCL, P36 OCD_SDA, P37 P30, WDOVF, CKSEL1 P31, CKSEL0 P10, AN0, SBI0 P11, AN1, SBO0, SDA0 P12, AN2, SBT0, SCL0 VSS P13, AN3 VDDI P14, AN4, SBI1 P15, AN5, SBO1, SDA1 P16, AN6, SBT1, SCL1 P17, AN7 P20, AN8, SBI4 P21, AN9, SBO4 P22, AN10, SBT4 P23, AN11 P24, DA0 P25, DA1 P26, ADTRG AVDD P32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 P97 PA0 PA1 PA2 PA3 PA4 PA5 PA6, DREQ0 PA7, DREQ1 VDD3 PB0, IRQ0 PB1, IRQ1 PB2, IRQ2 PB3, IRQ3 PB4, TM10IOA, IRQ4 PB5, TM10IOB, IRQ5 PB6, TM11IOA, IRQ6 PB7, TM11IOB, IRQ7 PC0, DREQ0 PC1, DREQ1 PC2, TM12IOA PC3, TM12IOB PD0, SBI1, TM14IOB, TM7IO PD1, SBO1, TM15IOA, TM8IO, SDA1 PD2, SBT1, TM15IOB, TM9IO, SCL1 PD3, SBI0, TM13IOA, TM4IO PD4, SBO0, TM13IOB, TM5IO, SDA0 PD5, SBT0, TM14IOA, TM6IO, SCL0 VSS VDDI VDD3 VDD3 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 P96 P95 P94 P93 P92 P91 P90 P87 P86 P85 VSS P84 P83 P82 P81 P80 P71 P72 P73 P74 VDDI P70, SYSCLK VSS OSCO OSCI LON VOUT, VDDI VDD3 XO XI, P75 P33 P67 TQFP128-P-1414A MAF00023DEM NRST VSS P66 VDDI P65 P64 P63 P62 P61 P60 P57, IRQ7 P56, IRQ6 P55, IRQ5 P54, IRQ4 P53 P52 P51 P50 VDD3 P47 P46 P45 P44 P43 P42 P41 P40 MEMMOD MOD TMOD P35 P34 Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. – Any applications other than the standard applications intended. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. 20080805