GI910 THRU GI917 MEDIUM-SWITCHING PLASTIC RECTIFIER Reverse Voltage - 50 to 800 Volts Forward Current - 3.0 Amperes FEATURES DO-201AD ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High surge current capability ♦ Construction utilizes void-free molded plastic technique ♦ High forward current operation ♦ Fast switching for high efficiency ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375 (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.210 (5.3) 0.190 (4.8) DIA. 0.375 (9.5) 0.285 (7.2) MECHANICAL DATA Case: JEDEC DO-201AD molded plastic body Terminals: Plated axial leads solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.04 ounce, 1.1 grams 0.052 (1.32) 1.0 (25.4) MIN. 0.048 (1.22) DIA. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GI910 GI911 GI912 GI914 GI916 GI917 UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 Volts Maximum average forward rectified current 0.375" (9.5mm) lead length at T A=90°C I(AV) 3.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 100.0 Amps VF 1.25 1.10 Volts IR 10.0 300.0 µA CJ 28.0 pF Maximum instantaneous forward voltage at: 3.0A 9.4A, TJ=175°C Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=100°C Typical junction capacitance (NOTE 1) trr 750 ns Maximum reverse recovery current IRM(REC) 2.0 Amps Typical thermal resistance (NOTE 3) RΘJA RΘJL 22.0 8.0 °C/W TJ ,TSTG -50 to +150 °C Maximum reverse recovery time (NOTE 2) Operating junction and storage temperature range NOTES: (1) Measured at 1 MHz and applied reverse voltage of 4.0 Volts (2) Reverse recovery test conditions: IF=1.0A, VR=30V, di/dt=50A/µs, and Irr=10% IRM for measurement of trr (3) Thermal resistance from junction to ambient and from junction to lead at 0.375" (9.5mm) lead length, both leads equally heat sink 4/98 RATINGS AND CHARACTERISTIC CURVES GI910 THRU GI917 FIG.1 - FORWARD CURRENT DERATING CURVE FIG. 2 - MAXIMUM PEAK FORWARD SURGE CURRENT = π 200 0.375” (9.5mm) LEAD LENGTH 0.8 x 0.8 x 0.04” (20 x 20 x 1mm) COPPER HEATSINKS 2.0 CAPACITIVE LOADS I(pk) 5.0 = I(AV) 10 20 1.0 0 30 50 70 90 110 130 150 170 PEAK FORWARD SURGE CURRENT, AMPERES I(pk) I(AV) 3.0 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) TJ=25°C 100 AMBIENT TEMPERATURE, °C NON-REPETITIVE TJ=150°C REPETITIVE 10 1 10 100 NUMBER OF CYCLES AT 60 HZ FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT MICROAMPERES 10 10 1 0.1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 TJ=100°C 1 TJ=50°C 0.1 0.01 0 TJ=25°C 20 40 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE 100 TJ=25°C f=1.0 MHz Vsig=50mVp-p 10 1 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % JUNCTION CAPACITANCE, pF INSTANTANEOUS FORWARD CURRENT AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 4.0 10 REVERSE VOLTAGE, VOLTS 100 100