Seme LAB BCY39A Small signal pnp transistor Datasheet

BCY39A
MECHANICAL DATA
Dimensions in mm (inches)
SMALL SIGNAL
PNP TRANSISTORS
8.51 (0.34)
9.40 (0.37)
7.75 (0.305)
8.51 (0.335)
6.10 (0.240)
6.60 (0.260)
12.70
(0.500)
min.
0.89
max.
(0.035)
APPLICATIONS
0.41 (0.016)
0.53 (0.021)
dia.
Small signal PNP transistors for relay
switching resistor logic circuits and general
purpose applications.
5.08 (0.200)
typ.
2.54
(0.100)
2
1
3
0.74 (0.029)
1.14 (0.045)
0.71 (0.028)
0.86 (0.034)
45°
TO39 PACKAGE (TO-205AD)
Underside View
Pin 1 = Emitter
Pin 2 = Base Pin 3 = Collector
ABSOLUTE MAXIMUM RATINGS (Tcase = 25°C unless otherwise stated)
VCB
VCE
VEB
ICM
IC(AV)
IBM
IB(AV)
IEM
IE(AV)
PTOT
Collector – Base Voltage
Collector – Emitter Voltage
Emitter – Base Voltage
Collector Current
Collector Current ave Over any 20ms
Base Current
Base Current ave Over any 20ms
Emitter Current
Emitter Current ave Over any 20ms
Total Power Dissipation
25V
25V
16V
100mA
30mA
30mA
15mW
100mA
65mA
230mW
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed
to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use.
Semelab encourages customers to verify that datasheets are current before placing orders.
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: [email protected]
Website: http://www.semelab.co.uk
Document Number 3080
Issue 1
BCY39A
THERMAL CHARACTERISTICS
CHARACTERISTICS
θj-amb
Junction to Ambient
0.3°C/mW
θj-case
Junction to Case
0.12°C/mW
ELECTRICAL CHARACTERISTICS (Tcase = 25°C unless otherwise stated)
Parameter
ICBO
Collector Cut-off Current
Test Conditions
VCB = -6V
IE = 0
VCB = -6V
IE = 0
Min.
Tamb = 100°C
IEBO
Emitter Cut-off Current
VEB = -6V
IC = 0
VEB = -6V
IC = 0
Tamb = 100°C
hFE
DC Current Gain
IC = 30mA
VCE = -1V
12
IC = 150mA
VCE = - 1V
10
ICM = 300mA VCE = - 6V
VCE(sat)
Collector – Emitter Saturation Voltage IC = 150mA
VBE
Base – Emitter Voltage
IB
Base – Current
NF
Noise Figure
hfe
Small Signal Current Gain
fT
Transistion Frequency
Typ.
Max. Unit
1
100
nA
0.1
2.5
µA
1
100
nA
0.1
2.5
µA
50
—
30
15
IB = 15mA
-0.46
-1.1
IC = 150mA
IB = - 1V
-1.5
-1.9
IE = 150mA
VCB = 0
IC = 500µA
VCE = -2V
f = 1kc/s
Rs = 500Ω
IC = 10mA
VCE = -6V
f = 1kc/s
IC = 1mA
VCE = -6V
3
14
35
0.45
1.5
mA
dB
8
15
V
100
—
MHz
*Pulse Test : Pulse Width < 300µs, Duty Cycle < 2%
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed
to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use.
Semelab encourages customers to verify that datasheets are current before placing orders.
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: [email protected]
Website: http://www.semelab.co.uk
Document Number 3080
Issue 1
Similar pages