Fairchild FAN3121C 30v pmos-nmos bridge driver Datasheet

FAN3278
30V PMOS-NMOS Bridge Driver
Features
Description


8V to 27V Optimum Operating Range

Output Drive-Voltage Magnitude Limited: < 13V
for VDD up to 30V

Biases Each Load Device OFF with a 100kΩ
Resistor when VDD Below Operating Level



Low-Voltage TTL Input Thresholds
The FAN3278 dual 1.5A gate driver is optimized to drive
a high-side P-channel MOSFET and a low-side
N-channel MOSFET in motor control applications
operating from a voltage rail up to 27V. Internal circuitry
limits the voltage applied to the gates of the external
MOSFETs to 13V maximum. The driver has TTL input
thresholds and provides buffer and level translation from
logic inputs. Internal circuitry prevents the output
switching devices from operating if the VDD supply
voltage is below the IC operation level. Internal 100kΩ
resistors bias the non-inverting output LOW and the
inverting output to VDD to keep the external MOSFETs
off during startup intervals when logic control signals
may not be present.


8-Lead SOIC Package
Drives High-Side PMOS and Low-Side NMOS in
Motor Control or Buck Step-Down Applications
Peak Gate Drives at 12V: +1.5A Sink, -1.0A Source
Internal Resistors Hold Driver Off When
No Inputs Present
Rated from –40°C to +125°C Ambient
Applications

Motor Control with PMOS / NMOS Half-Bridge
Configuration

Buck Converters with High-Side PMOS Device;
100% Duty Cycle Operation Possible

Logic-Controlled Load Circuits with High-Side
PMOS Switch
The FAN3278 driver incorporates MOSFET devices for
the final output stage, providing high current throughout
the MOSFET turn-on / turn-off transition to minimize
switching loss. The internal gate-drive regulators
provide optimum gate-drive voltage when operating
from a rail of 8V to 27V. The FAN3278 can be driven
from a voltage rail of less than 8V; however, its gate
drive current is reduced.
The FAN3278 has two independent ENABLE pins that
default to ON if not connected. If the ENABLE pin for
non-inverting channel A is pulled LOW, OUTA is forced
LOW. If the ENABLE pin for inverting channel B is
pulled LOW, OUTB is forced HIGH. If an input is left
unconnected, internal resistors bias the inputs such that
the external MOSFETs are OFF.
Figure 1. Typical Application
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
www.fairchildsemi.com
FAN3278 — 30V PMOS-NMOS Bridge Driver
January 2011
Part Number
FAN3278TMX
Logic
Input
Threshold
Packing
Method
TTL
2,500 Units on
Tape & Reel
Non-Inverting Channel and Inverting Channel with Dual Enable
FAN3278 — 30V PMOS-NMOS Bridge Driver
Ordering Information
Figure 2. Typical 3-Phase Blower Motor Drive Application
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
www.fairchildsemi.com
2
Figure 3. Pin Configuration (Top View)
Thermal Characteristics(1)
Package
JL(2)
JT(3)
JA(4)
JB(5)
JT(6)
Unit
8-Pin Small-Outline Integrated Circuit (SOIC)
40
31
89
43
3
°C/W
Notes:
1. Estimates derived from thermal simulation; actual values depend on the application.
2. Theta_JL (JL): Thermal resistance between the semiconductor junction and the bottom surface of all the leads
(including any thermal pad) that are typically soldered to a PCB.
3. Theta_JT (JT): Thermal resistance between the semiconductor junction and the top surface of the package,
assuming it is held at a uniform temperature by a top-side heatsink.
4. Theta_JA (ΘJA): Thermal resistance between junction and ambient, dependent on the PCB design, heat sinking,
and airflow. The value given is for natural convection with no heatsink using a 2S2P board, as specified in
JEDEC standards JESD51-2, JESD51-5, and JESD51-7, as appropriate.
5. Psi_JB (JB): Thermal characterization parameter providing correlation between semiconductor junction
temperature and an application circuit board reference point for the thermal environment defined in Note 4. For
the SOIC-8 package, the board reference is defined as the PCB copper adjacent to pin 6.
6. Psi_JT (JT): Thermal characterization parameter providing correlation between the semiconductor junction
temperature and the center of the top of the package for the thermal environment defined in Note 4.
FAN3278 — 30V PMOS-NMOS Bridge Driver
Pin Configuration
Pin Definitions
Pin#
Name
1
ENA
Enable Input for Channel A. Pull pin LOW to inhibit driver A. ENA has TTL thresholds.
8
ENB
Enable Input for Channel B. Pull pin LOW to inhibit driver B. ENB has TTL thresholds.
3
GND
Ground. Common ground reference for input and output circuits.
2
INA
Input to Channel A.
4
INB
Input to Channel B.
7
OUTA
Gate Drive Output A: Held LOW unless required input is present and VDD is above the internal
voltage threshold where the IC is functional.
OUTB
Gate Drive Output B (inverted from the input). Held HIGH unless the required input is present
and VDD is above the internal voltage threshold where the IC is functional.
5
6
VDD
Description
Supply Voltage. Provides power to the IC.
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
www.fairchildsemi.com
3
FAN3278 (Channel A)
ENA
INA
0
FAN3278 (Channel B)
OUTA
(7)
0
0
ENB
INB
OUTB
(7)
0
0
1
0
1
0
0
1
1
1(7)
0(7)
0
1(7)
0(7)
1
1(7)
1
1
1(7)
1
0
Note:
7. Default input signal if no external connection is made.
Block Diagram
VDD
VDD
100k
FAN3278 — 30V PMOS-NMOS Bridge Driver
Output Logic
100k
ENA 1
8
ENB
7
OUTA
6
VDD
5
OUTB
13V
INA
LS
Predriver
2
100k
100k
Low-Side
Drive
Regulator
GND 3
High-Side
Drive
Regulator
INB
HS
Predriver
4
100k
100k
VDD - 13V
Figure 4. Block Diagram
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
www.fairchildsemi.com
4
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.
Symbol
Parameter
Min.
Max.
Unit
-0.3
30.0
V
VDD
VDD to PGND
VEN
ENA, ENB to GND
GND - 0.3 VDD + 0.3
V
VIN
INA, INB to GND
GND - 0.3 VDD + 0.3
V
OUTA, OUTB to GND
GND - 0.3 VDD + 0.3
V
VOUT
TL
Lead Soldering Temperature (10 Seconds)
TJ
Junction Temperature
TSTG
Storage Temperature
ESD
Electrostatic Discharge
Protection Level
+260
ºC
-55
+150
ºC
-65
+150
ºC
Human Body Model, JEDEC JESD22-A114
2
Charged Device Model, JEDEC JESD22-C101
2
kV
FAN3278 — 30V PMOS-NMOS Bridge Driver
Absolute Maximum Ratings
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended
operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not
recommend exceeding them or designing to Absolute Maximum Ratings.
Symbol
Parameter
Min.
Max.
Unit
VDD
Supply Voltage Range
8
27
V
VEN
Enable Voltage (ENA, ENB)
0
VDD
V
VIN
Input Voltage (INA, INB)
0
VDD
V
TA
Operating Ambient Temperature
-40
+125
°C
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
www.fairchildsemi.com
5
Unless otherwise noted, VDD=12V and TJ=-40°C to +125°C. Currents are defined as positive into the device (Isink) and
negative out of the device (Isource).
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
27
V
2.0
mA
Supply
VDD
Optimum Operating Range(8)
IDD
Supply Current Inputs / EN Not
Connected
VON
Turn-On Voltage(9)
VHYS
Turn-On / Turn-Off Hysteresis
8
1.3
(9)
INA=ENA=VDD, INB=ENB=0V
3.8
V
INA=ENA=VDD, INB=ENB=0V
10
mV
1.1
V
Input(9)
VIL
INx Logic Low Threshold
VIH
INx Logic High Threshold
VHYS
Logic Hysteresis Voltage
0.8
1.80
2.25
V
0.4
0.7
1.0
V
0.8
1.2
Enable
VENL
Enable Logic Low Threshold
EN from 5V to 0V
VENH
Enable Logic High Threshold
EN from 0V to 5V
VHYS
Logic Hysteresis Voltage
RPU
Enable Pull-Up Resistance
tD1
tD2
tD2
tD1
1.60
(10)
V
2.25
V
0.7
V
100
kΩ
(11)
0 - 5VIN, 1V/ns Slew Rate
44
70
ns
(11)
0 – 5VIN, 1V/ns Slew Rate
33
60
ns
(11)
0 - 5VIN, 1V/ns Slew Rate
39
70
ns
(11)
0 – 5VIN, 1V/ns Slew Rate
29
60
ns
Propagation A Delay, EN Rising
Propagation A Delay, EN Falling
Propagation B Delay, EN Rising
Propagation B Delay, EN Falling
FAN3278 — 30V PMOS-NMOS Bridge Driver
Electrical Characteristics
Continued on the following page…
Timing Diagrams
90%
Output
10%
Input V
INH
or
V
INL
Enable
tD1
tD2
tRISE
tFALL
Figure 5. Non-Inverting
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
Figure 6. Inverting
www.fairchildsemi.com
6
Unless otherwise noted, VDD=12V and TJ=-40°C to +125°C. Currents are defined as positive into the device (Isink) and
negative out of the device (Isource).
Symbol
Parameter
Conditions
Min.
Typ. Max.
Unit
Output
IPK_OFF
OUT Current, Peak, Turn-Off(10)
CLOAD=0.1µF, f=1kHz
1.5
A
IPK_ON
(10)
OUT Current, Peak, Turn-On
CLOAD=0.1µF, f=1kHz
-1.0
A
IOFF
OUT Current, Mid-Voltage, Turn-Off(10
OUT at VDD, CLOAD=0.1µF,
f=1kHz
1.0
A
ION
OUT Current, Mid-Voltage, Turn-On(10)
OUT at VDD/2, CLOAD=0.1µF,
f=1kHz
-0.5
A
VOUTA
OUTA Drive Voltage
VDD=27V, INA=“HI”
11
13
V
VOUTB
OUTB Drive Voltage, VDD – VOUTB
VDD=27V, INA=“HI”
11
13
V
VOUTA
OUTA Drive Voltage
VDD=10V, INB=“HI”
6.5
7.0
V
VOUTB
OUTB Drive Voltage, VDD – VOUTB
VDD=10V, INB=“HI”
6.5
7.0
V
VDD=6V, CLOAD=0.1µF
4.2
Ω
VDD=6V, CLOAD=0.1µF
10.3
Ω
VDD=6V, CLOAD=0.1µF
6.8
Ω
VDD=6V, CLOAD=0.1µF
13.7
Ω
RO_A_SINK OUTA Sink Impedance (Turn-Off)(10)
(10)
RO_A_SRC OUTA Source Impedance (Turn-On)
(10)
RO_B_SINK OUTB Sink Impedance (Turn-On)
(10)
RO_B_SRC OUTB Source Impedance (Turn-Off)
(11)
tON,N
Output A Rise Time
CLOAD=1000pF to GND
17
30
ns
tOFF,N
Output A Fall Time(11)
CLOAD=1000pF to GND
8
15
ns
tON,P
(11)
CLOAD=1000pF to VDD
21
30
ns
CLOAD=1000pF to VDD
8
15
ns
0 - 5VIN, 1V/ns Slew Rate
45
70
ns
0 - 5VIN, 1V/ns Slew Rate
35
60
ns
tOFF,P
tD1
tD2
IRVS
Output B Fall Time
(11)
Output B Rise Time
Output Propagation Delay On
(11)
Output Propagation Delay Off
(11)
(10)
Output Reverse Current Withstand
500
FAN3278 — 30V PMOS-NMOS Bridge Driver
Electrical Characteristics (Continued)
mA
Notes:
8. The internal gate-drive regulators provide optimum gate-drive voltage when operating from a rail of 8V to 27V.
The FAN3278 can be driven from a voltage rail of less than 8V; however, with reduced gate drive current.
9. EN inputs have near-TTL thresholds (refer to the ENABLE section).
10. Not tested in production.
11. See the Timing Diagrams of Figure 5 and Figure 6.
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
www.fairchildsemi.com
7
Typical characteristics are provided at TA=25°C and VDD=12V unless otherwise noted.
Figure 7. IDD (Static) vs. Supply Voltage(12)
Figure 8. IDD (Static) vs. Temperature(12)
Figure 9. IDD (No Load) vs. Frequency
Figure 10. IDD (1nF Load) vs. Frequency
FAN3278 — 30V PMOS-NMOS Bridge Driver
Typical Performance Characteristics
Figure 11. Input Thresholds vs. Temperature
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
www.fairchildsemi.com
8
Typical characteristics are provided at TA=25°C and VDD=12V unless otherwise noted.
Figure 12. Propagation Delays vs. Temperature
Figure 13. Propagation Delays vs. Temperature
Figure 14. Rise and Fall Times vs. Temperature
Figure 15. Rise and Fall Times vs. Temperature
Figure 16. Gate Drive Voltage vs. Temperature
Figure 17. Gate Drive Voltage vs. Temperature
FAN3278 — 30V PMOS-NMOS Bridge Driver
Typical Performance Characteristics
Note:
12. For any inverting inputs pulled LOW, non-inverting inputs pulled HIGH, or outputs driven HIGH; static IDD
increases by the current flowing through the corresponding pull-up/down resistor, shown in Figure 4.
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
www.fairchildsemi.com
9
Input Thresholds
The FAN3278 driver has TTL input thresholds and
provides buffer and level translation functions from
logic inputs. The input thresholds meet industrystandard TTL-logic thresholds, independent of the VDD
voltage, and there is a hysteresis voltage of
approximately 0.4V. These levels permit the inputs to
be driven from a range of input logic signal levels for
which a voltage over 2V is considered logic HIGH. The
driving signal for the TTL inputs should have fast rising
and falling edges with a slew rate of 6V/µs or faster, so
a rise time from 0 to 3.3V should be 550ns or less.
With reduced slew rate, circuit noise could cause the
driver input voltage to exceed the hysteresis voltage
and retrigger the driver input inadvertently.
Figure 18. Non-Inverting Startup Waveforms
Static Supply Current
In the IDD (static) typical performance characteristics
(see Figure 7 and Figure 8), the curve is produced with
all inputs / enables floating (OUTA is LOW, OUTB is
HIGH) and indicates the lowest static IDD current for the
tested configuration. For other states, additional current
flows through the 100k resistors on the inputs and
outputs, shown in the block diagram (see Figure 4). In
these cases, the static IDD current is the value obtained
from the curves plus this additional current.
FAN3278 — 30V PMOS-NMOS Bridge Driver
Applications Information
Figure 19 illustrates startup waveforms for inverting
channel B. At power-up, the driver output for channel B
is tied to VDD through an internal 100kΩ resistor until
VDD reaches the voltage where the device starts
operating, then OUTB operates out of phase with INB.
Gate Drive Regulator
FAN3278 incorporates internal regulators to regulate the
gate drive voltage. The output pin slew rate is
determined by this gate drive voltage and the load on
the output. It is not user adjustable, but a series resistor
can be added if a slower rise or fall time is needed at
the MOSFET gate.
Startup Operation
The FAN3278 startup logic is optimized to drive a groundreferenced N-channel MOSFET with channel A and a
VDD-referenced P-channel MOSFET with channel B.
The optimum operating voltage of the FAN3278 is 8V to
27V. It has an internal “watchdog” circuit that provides a
loose UVLO turn-on voltage (VON) of approximately 3.8V
with a small hysteresis of about 10mV. However, it is
recommended that VDD is greater than 4.75V in all
application circuits.
Figure 19. Inverting Startup Waveforms
It is possible, during startup, before VDD has reached
approximately 4.5V, that the output pulse width may
take a few switching cycles to reach the full duty-cycle
of the input pulse. This is due to internal propagation
delays affecting the operation with higher switching
frequency (e.g. >100kHz) and slow VDD ramp-up (e.g.
<20V/ms). For this reason, it is recommended that VDD
should be greater than 4.75V before any INA or INB
signals are present.
When the VDD supply voltage is below the level needed
to operate the internal circuitry, the outputs are biased
to hold the external MOSFETs in OFF state. Internal
100kΩ resistors bias the non-inverting output LOW and
the inverting output to VDD to keep the external
MOSFETs off during startup intervals when input control
signals may not be present.
For high-frequency applications (several hundred kHz
up to 1MHz), where the above recommendation of VDD
> 4.75V is not possible, the use of ENABLES to
actively hold the outputs LOW until VDD > 4.75V
assures the driver output pulse width follows the input
from 4.75V up to 28V.
Figure 18 shows startup waveforms for non-inverting
channel A. At power-up, the driver output for channel A
remains LOW until VDD reaches the voltage where the
device starts operating, then OUTA operates in-phase
with INA.
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
www.fairchildsemi.com
10
To enable this IC to turn a device on quickly, a local
high-frequency bypass capacitor, CBYP, with low ESR
and ESL should be connected between the VDD and
GND pins with minimal trace length. This capacitor is in
addition to bulk electrolytic capacitance of 10µF to 47µF
commonly found on driver and controller bias circuits.

Thermal Guidelines
Gate drivers used to switch MOSFETs and IGBTs at
high frequencies can dissipate significant amounts of
power. It is important to determine the driver power
dissipation and the resulting junction temperature in the
application to ensure the part is operating within
acceptable temperature limits.
A typical criterion for choosing the value of CBYP is to
keep the ripple voltage on the VDD supply to ≤5%. This
is often achieved with a value ≥20 times the equivalent
load capacitance CEQV, defined as QGATE/VDD. Ceramic
capacitors of 0.1µF to 1µF or larger are common
choices, as are dielectrics, such as X5R and X7R, with
stable temperature characteristics and high pulse
current capability.
The total power dissipation in a gate driver is the sum of
two components, PGATE and PDYNAMIC:
PTOTAL=PGATE + PDYNAMIC
If circuit noise affects normal operation, the value of
CBYP may be increased to 50-100 times the CEQV or CBYP
may be split into two capacitors. One should be a larger
value, based on equivalent load capacitance, and the
other a smaller value, such as 1-10nF, mounted closest
to the VDD and GND pins to carry the higher-frequency
components of the current pulses. The bypass capacitor
must provide the pulsed current from both of the driver
channels and, if the drivers are switching
simultaneously, the combined peak current sourced
from the CBYP can be twice as large as when a single
channel is switching.
PGATE=QG • VGS • fSW

Keep the driver as close to the load as possible to
minimize the length of high-current traces. This
reduces the series inductance to improve highspeed switching, while minimizing the loop area
that can couple EMI to the driver inputs and
surrounding circuitry.


Dynamic Pre-drive / Shoot-through Current: Power loss
resulting from internal current consumption under
dynamic operating conditions, including pin pull-up /
pull-down resistors, can be obtained using the “IDD (NoLoad) vs. Frequency” graphs in Figure 9 to determine
the current IDYNAMIC drawn from VDD under actual
operating conditions.
PDYNAMIC=IDYNAMIC • VDD
(3)
Once the power dissipated in the driver is determined,
the driver junction rise with respect to circuit board can
be evaluated using the following thermal equation,
assuming JB was determined for a similar thermal
design (heat sinking and air flow):
TJ
=PTOTAL • JB + TB
(4)
where:
TJ =driver junction temperature
JB =(psi) thermal characterization parameter relating
temperature rise to total power dissipation
TB =board temperature in location defined in
Note 1 under Thermal Resistance table.
If the inputs to a channel are not externally
connected, the internal 100k resistors indicated
on block diagrams command a low output on
channel A and a high output on channel B. In noisy
environments, it may be necessary to tie inputs of
an unused channel to VDD or GND using short
traces to prevent noise from causing spurious
output switching.
As an example of a power dissipation calculation,
consider an application driving two MOSFETs (one Pchannel and one N-channel, both with a gate charge of
60nC each) with VGS=VDD=12V. At a switching
frequency of 200kHz, the total power dissipation is:
Many high-speed power circuits can be susceptible
to noise injected from their own output or other
external sources, possibly causing output mistriggering. These effects can be obvious if the
circuit is tested in breadboard or non-optimal circuit
layouts with long input, enable, or output leads. For
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
(2)
This needs to be calculated for each P-channel and Nchannel MOSFET where the QG is likely to be different.
The FAN3278 gate driver incorporates fast-reacting
input circuits, short propagation delays, and powerful
output stages capable of delivering current peaks over
1.5A to facilitate fast voltage transition times. The
following layout and connection guidelines are strongly
recommended:
Keep high-current output and power ground paths
separate from logic and enable input signals and
signal ground paths. This is especially critical when
dealing with TTL-level logic thresholds at driver
inputs and enable pins.
(1)
Gate Driving Loss: The most significant power loss
results from supplying gate current (charge per unit
time) to switch the load MOSFET on and off at the
switching frequency. The power dissipation that results
from driving a MOSFET with a specified gate-source
voltage, VGS, with gate charge, QG, at switching
frequency, fSW, is determined by:
Layout and Connection Guidelines

The turn-on and turn-off current paths should be
minimized, as discussed above.
FAN3278 — 30V PMOS-NMOS Bridge Driver
best results, make connections to all pins as short
and direct as possible.
VDD Bypass Capacitor Guidelines
PGATE=60nC • 12V • 200kHz • 2=0.288W
(5)
PDYNAMIC=1.65mA • 12V =0.020W
(6)
PTOTAL=0.308W
(7)
www.fairchildsemi.com
11
TB=TJ - PTOTAL • JB
(8)
TB=120°C – 0.308W • 43°C/W=107°C
(9)
Test Circuit
Figure 20. Quasi-Static IOUT / VOUT Test Circuit
Differences between FAN3278 and FAN3268
FAN3278 — 30V PMOS-NMOS Bridge Driver
The SOIC-8 package has a junction-to-board thermal
characterization parameter of JB=43°C/W. In a system
application, the localized temperature around the device
is a function of the layout and construction of the PCB
along with airflow across the surfaces. To ensure
reliable operation, the maximum junction temperature of
the device must not exceed the absolute maximum
rating of 150°C; with 80% derating, TJ would be limited
to 120°C. Rearranging Equation 4 determines the board
temperature required to maintain the junction
temperature below 120°C:
FAN3278 and FAN3268 are pin-compatible to each other and are designed to drive one P-Channel and one
N-channel MOSFET in applications such as battery-powered compact fan / pump DC motor drives. However, there
are key differences, highlighted in Table 1.
Table 1. Differences between FAN3278 and FAN3268
FAN3278
Supply Voltage
Gate Drive Regulator
Minimum Operating
Voltage
27V Operating Maximum
30V Absolute Maximum
FAN3268
18V Operating Maximum
20V Absolute Maximum
Yes, since the maximum operating VDD can No gate drive regulator is needed. The
be as high as 27V, the gate voltage to the
gate drive voltage is VDD and the
external MOSFETs is limited to about 13V. FAN3268 switches rail-to-rail.
The optimum operating range is 8V to 27V.
After the IC turns on at about 3.8V, the
4.1V is the UVLO turn-off voltage
output tracks VDD up to the regulated
which is the minimum operating
voltage rail of about 11~13V. Below 8V of
VDD, the FAN3278 operates, but (a) slower voltage.
and (b) with limited gate drive voltage until
it reaches around 8V.
The IC starts operating approximately at
3.8V which acts as a loose UVLO
threshold. It incorporates a “smart startup”
feature where the outputs are held OFF
before the IC starts operating.
Has the tight UVLO threshold of 4.5V
on / 4.1V off. Incorporates “smart
startup” (outputs held OFF before IC is
fully operational at the UVLO
threshold).
Output Gate Drive
Architecture
Standard MOS-based output structure with
gate drive clamp.
Compound MillerDrive™ architecture
in the final output stage to provide a
more efficient gate drive current during
the Miller plateau stage of the turnon/turn-off switching transition.
OUTB Gate Drive
Current Strength
Optimized for P-channel: The turn-OFF
(1.5 A) is stronger than turn-ON (1.0A).
P-channel turn-ON (2.4A) is stronger
than turn-OFF (1.6A).
Startup
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
www.fairchildsemi.com
12
Part
Number
Type
Gate
Input
Drive(13)
Threshold
(Sink / Src)
FAN3111C Single 1A
+1.1A / -0.9A
CMOS
FAN3111E
Single 1A
+1.1A / -0.9A
External
FAN3100C Single 2A
+2.5A / -1.8A
FAN3100T
Single 2A
FAN3226C
Logic
Package
Single Channel of Dual-Input/Single-Output
SOT23-5, MLP6
Single Non-Inverting Channel with External Reference
SOT23-5, MLP6
CMOS
Single Channel of Two-Input/One-Output
SOT23-5, MLP6
+2.5A / -1.8A
TTL
Single Channel of Two-Input/One-Output
SOT23-5, MLP6
Dual 2A
+2.4A / -1.6A
CMOS
Dual Inverting Channels + Dual Enable
SOIC8, MLP8
FAN3226T
Dual 2A
+2.4A / -1.6A
TTL
Dual Inverting Channels + Dual Enable
SOIC8, MLP8
FAN3227C
Dual 2A
+2.4A / -1.6A
CMOS
Dual Non-Inverting Channels + Dual Enable
SOIC8, MLP8
FAN3227T
Dual 2A
+2.4A / -1.6A
TTL
Dual Non-Inverting Channels + Dual Enable
SOIC8, MLP8
FAN3228C
Dual 2A
+2.4A / -1.6A
CMOS
Dual Channels of Two-Input/One-Output, Pin Config.1
SOIC8, MLP8
FAN3228T
Dual 2A
+2.4A / -1.6A
TTL
Dual Channels of Two-Input/One-Output, Pin Config.1
SOIC8, MLP8
FAN3229C
Dual 2A
+2.4A / -1.6A
CMOS
Dual Channels of Two-Input/One-Output, Pin Config.2
SOIC8, MLP8
FAN3229T
Dual 2A
+2.4A / -1.6A
TTL
Dual Channels of Two-Input/One-Output, Pin Config.2
SOIC8, MLP8
FAN3268T
Dual 2A
+2.4A / -1.6A
TTL
Non-Inverting Channel (NMOS) and Inverting Channel
(PMOS) + Dual Enables
SOIC8
FAN3278T
Dual 2A
+1.4A / -1.0A
TTL
30V Non-Inverting (NMOS) and Inverting (PMOS) +
Dual Enable
SOIC8
FAN3223C
Dual 4A
+4.3A / -2.8A
CMOS
Dual Inverting Channels + Dual Enable
SOIC8, MLP8
FAN3223T
Dual 4A
+4.3A / -2.8A
TTL
Dual Inverting Channels + Dual Enable
SOIC8, MLP8
FAN3224C
Dual 4A
+4.3A / -2.8A
CMOS
Dual Non-Inverting Channels + Dual Enable
SOIC8, MLP8
FAN3224T
Dual 4A
+4.3A / -2.8A
TTL
Dual Non-Inverting Channels + Dual Enable
SOIC8, MLP8
FAN3225C
Dual 4A
+4.3A / -2.8A
CMOS
Dual Channels of Two-Input/One-Output
SOIC8, MLP8
FAN3225T
Dual 4A
+4.3A / -2.8A
TTL
Dual Channels of Two-Input/One-Output
SOIC8, MLP8
FAN3121C Single 9A
+9.7A / -7.1A
CMOS
Single Inverting Channel + Enable
SOIC8, MLP8
FAN3121T
Single 9A
+9.7A / -7.1A
TTL
Single Inverting Channel + Enable
SOIC8, MLP8
FAN3122T
Single 9A
+9.7A / -7.1A
CMOS
Single Non-Inverting Channel + Enable
SOIC8, MLP8
FAN3122C Single 9A
+9.7A / -7.1A
TTL
Single Non-Inverting Channel + Enable
SOIC8, MLP8
(14)
Notes:
13. Typical currents with OUT at 6V and VDD=12V.
14. Thresholds proportional to an externally supplied reference voltage.
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
www.fairchildsemi.com
13
FAN3278 — 30V PMOS-NMOS Bridge Driver
Table 2. Related Products
5.00
4.80
A
0.65
3.81
8
5
B
6.20
5.80
PIN ONE
INDICATOR
1.75
4.00
3.80
1
5.60
4
1.27
(0.33)
0.25
M
1.27
C B A
LAND PATTERN RECOMMENDATION
0.25
0.10
SEE DETAIL A
1.75 MAX
0.25
0.19
C
0.10
0.51
0.33
0.50 x 45°
0.25
R0.10
C
OPTION A - BEVEL EDGE
GAGE PLANE
R0.10
OPTION B - NO BEVEL EDGE
0.36
NOTES: UNLESS OTHERWISE SPECIFIED
8°
0°
0.90
0.406
A) THIS PACKAGE CONFORMS TO JEDEC
MS-012, VARIATION AA, ISSUE C,
B) ALL DIMENSIONS ARE IN MILLIMETERS.
C) DIMENSIONS DO NOT INCLUDE MOLD
FLASH OR BURRS.
D) LANDPATTERN STANDARD: SOIC127P600X175-8M.
E) DRAWING FILENAME: M08AREV13
SEATING PLANE
(1.04)
DETAIL A
SCALE: 2:1
Figure 21. 8-Lead, Small-Outline Integrated Circuit (SOIC)
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner
without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or
obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions,
specifically the warranty therein, which covers Fairchild products.
Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/packaging/.
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
www.fairchildsemi.com
14
FAN3278 — 30V PMOS-NMOS Bridge Driver
Physical Dimensions
FAN3278 — 30V PMOS-NMOS Bridge Driver
© 2010 Fairchild Semiconductor Corporation
FAN3278 • Rev. 1.0.0
www.fairchildsemi.com
15