M MCP3221 Low Power 12-Bit A/D Converter With I2C™ Interface Features Description • • • • • The Microchip Technology Inc. MCP3221 is a successive approximation A/D converter with 12-bit resolution. Available in the SOT-23 package, this device provides one single-ended input with very low power consumption. Based on an advanced CMOS technology, the MCP3221 provides a low maximum conversion current and standby current of 250 µA and 1 µA, respectively. Low current consumption, combined with the small SOT-23 package, make this device ideal for battery-powered and remote data acquisition applications. • • • • • • • • 12-bit resolution ±1 LSB DNL, ±2 LSB INL max. 250 µA max conversion current 5 nA typical standby current, 1 µA max. I2C™ compatible serial interface - 100 kHz I2C Standard Mode - 400 kHz I2C Fast Mode Up to 8 devices on a single 2-Wire bus 22.3 ksps in I2C Fast Mode Single-ended analog input channel On-chip sample and hold On-chip conversion clock Single-supply specified operation: 2.7V to 5.5V Temperature range: - Industrial: -40°C to +85°C - Extended: -40°C to +125°C Small SOT-23 package Applications • • • • • Data Logging Multi-zone Monitoring Hand-Held Portable Applications Battery-Powered Test Equipment Remote or Isolated Data Acquisition Communication to the MCP3221 is performed using a 2-wire, I2C compatible interface. Standard (100 kHz) and Fast (400 kHz) I2C modes are available with the device. An on-chip conversion clock enables independent timing for the I2C and conversion clocks. The device is also addressable, allowing up to eight devices on a single 2-wire bus. The MCP3221 runs on a single supply voltage that operates over a broad range of 2.7V to 5.5V. This device also provides excellent linearity of ±1 LSB differential non-linearity and ±2 LSB integral non-linearity, maximum. Functional Block Diagram VDD Package Type DAC 5-Pin SOT-23A VSS 2 Comparator 5 SCL MCP3221 VDD 1 VSS AIN 3 AIN – Sample and Hold 12-bit SAR + Clock Control Logic I2C™ Interface 4 SDA SCL 2003 Microchip Technology Inc. SDA DS21732B-page 1 MCP3221 1.0 ELECTRICAL CHARACTERISTICS PIN FUNCTION TABLE Name Function Absolute Maximum Ratings † VDD +2.7V to 5.5V Power Supply VDD...................................................................................7.0V VSS Ground Analog input pin w.r.t. VSS .......... ............. -0.6V to VDD +0.6V AIN Analog Input SDA and SCL pins w.r.t. VSS........... .........-0.6V to VDD +1.0V SDA Serial Data In/Out Storage temperature .....................................-65°C to +150°C SCL Serial Clock In Ambient temp. with power applied ................-65°C to +125°C Maximum Junction Temperature .......... .........................150°C ESD protection on all pins (HBM) .................................≥ 4 kV † Stresses above those listed under “Maximum ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise noted, all parameters apply at VDD = 5.0V, VSS = GND, RPU = 2 kΩ TAMB = -40°C to +85°C, I2C Fast Mode Timing: fSCL = 400 kHz (Note 3). Parameters Sym Min Typ Max Units Conditions DC Accuracy Resolution 12 Integral Nonlinearity INL Differential Nonlinearity DNL — bits ±0.75 ±2 LSB — ±0.5 ±1 LSB Offset Error — ±0.75 ±2 LSB No missing codes Gain Error — -1 ±3 LSB THD — -82 — dB VIN = 0.1V to 4.9V @ 1 kHz Signal-to-Noise and Distortion SINAD — 72 — dB VIN = 0.1V to 4.9V @ 1 kHz Spurious-Free Dynamic Range SFDR — 86 — dB VIN = 0.1V to 4.9V @ 1 kHz VSS-0.3 — VDD+0.3 V 2.7V ≤ VDD ≤ 5.5V -1 — +1 µA Dynamic Performance Total Harmonic Distortion Analog Input Input Voltage Range Leakage Current SDA/SCL (open-drain output): Data Coding Format Straight Binary High-level input voltage VIH 0.7 VDD — — V Low-level input voltage VIL — — 0.3 VDD V VOL — — 0.4 V IOL = 3 mA, RPU = 1.53 kΩ VHYST — 0.05 VDD — V fSCL = 400 kHz only Low-level output voltage Hysteresis of Schmitt trigger inputs Note 1: 2: 3: 4: 5: “Sample time” is the time between conversions once the address byte has been sent to the converter. Refer to Figure 5-6. This parameter is periodically sampled and not 100% tested. RPU = Pull-up resistor on SDA and SCL. SDA and SCL = VSS to VDD at 400 kHz. tACQ and tCONV are dependent on internal oscillator timing. See Figure 5-5 and Figure 5-6 for relation to SCL. DS21732B-page 2 2003 Microchip Technology Inc. MCP3221 DC ELECTRICAL SPECIFICATIONS (CONTINUED) Electrical Characteristics: Unless otherwise noted, all parameters apply at VDD = 5.0V, VSS = GND, RPU = 2 kΩ TAMB = -40°C to +85°C, I2C Fast Mode Timing: fSCL = 400 kHz (Note 3). Parameters Input leakage current Output leakage current Sym Min Typ Max Units Conditions ILI -1 — +1 µA VIN = 0.1 VDD and 0.9 VDD ILO -1 — +1 µA VOUT = 0.1 VSS and 0.9 VDD CIN, COUT — — 10 pF TAMB = 25°C, f = 1 MHz; (Note 2) CB — — 400 pF SDA drive low, 0.4V VDD 2.7 — 5.5 V Conversion Current IDD — 175 250 µA Standby Current IDDS — 0.005 1 µA SDA, SCL = VDD Active bus current IDDA — — 120 µA Note 4 Conversion Time tCONV — 8.96 — µs Note 5 Analog Input Acquisition Time tACQ — 1.12 — µs Note 5 Sample Rate fSAMP — — 22.3 ksps Pin capacitance (all inputs/outputs) Bus Capacitance Power Requirements Operating Voltage Conversion Rate Note 1: 2: 3: 4: 5: fSCL = 400 kHz (Note 1) “Sample time” is the time between conversions once the address byte has been sent to the converter. Refer to Figure 5-6. This parameter is periodically sampled and not 100% tested. RPU = Pull-up resistor on SDA and SCL. SDA and SCL = VSS to VDD at 400 kHz. tACQ and tCONV are dependent on internal oscillator timing. See Figure 5-5 and Figure 5-6 for relation to SCL. TEMPERATURE SPECIFICATIONS Electrical Characteristics: Unless otherwise noted, all parameters apply at VDD = 5.0V, VSS = GND. Parameters Symbol Min Typ Max Units Industrial Temperature Range TA -40 — +85 °C Extended Temperature Range TA -40 — +125 °C Operating Temperature Range TA -40 — +125 °C Storage Temperature Range TA -65 — +150 °C θJA — 256 — °C/W Conditions Temperature Ranges Thermal Package Resistances Thermal Resistance, 5L-SOT23A 2003 Microchip Technology Inc. DS21732B-page 3 MCP3221 TIMING SPECIFICATIONS Electrical Characteristics: All parameters apply at VDD = 2.7V - 5.5V, VSS = GND, TAMB = -40°C to +85°C. Parameters Sym Min Typ Max Units Conditions 2 I C Standard Mode Clock frequency fSCL 0 — 100 kHz Clock high time THIGH 4000 — — ns Clock low time TLOW 4700 — — ns TR — — 1000 ns From V L to VIH (Note 1) From V L to VIH (Note 1) SDA and SCL rise time TF — — 300 ns THD:STA 4000 — — ns START condition setup time TSU:STA 4700 — — ns Data input setup time TSU:DAT 250 — — ns STOP condition setup time TSU:STO 4000 — — ns STOP condition hold time THD:STD 4000 — — ns SDA and SCL fall time START condition hold time Output valid from clock TAA — — 3500 ns Bus free time TBUF 4700 — — ns Note 2 Input filter spike suppression TSP — — 50 ns SDA and SCL pins (Note 1) I2C Fast Mode Clock frequency FSCL 0 — 400 kHz Clock high time THIGH 600 — — ns Clock low time TLOW 1300 — — ns TR 20 + 0.1CB — 300 ns From V L to VIH (Note 1) From V L to VIH (Note 1) SDA and SCL rise time TF 20 + 0.1CB — 300 ns THD:STA 600 — — ns START condition setup time TSU:STA 600 — — ns Data input hold time THD:DAT 0 — 0.9 ms SDA and SCL fall time START condition hold time Data input setup time TSU:DAT 100 — — ns STOP condition setup time TSU:STO 600 — — ns STOP condition hold time THD:STD 600 — — ns Output valid from clock TAA — — 900 ns Bus free time TBUF 1300 — — ns Note 2 Input filter spike suppression TSP — — 50 ns SDA and SCL pins (Note 1) Note 1: 2: This parameter is periodically sampled and not 100% tested. Time the bus must be free before a new transmission can start. THIGH TF SCL SDA IN SDA OUT FIGURE 1-1: DS21732B-page 4 VHYS TR TSU:STA TLOW TSP THD:DAT TSU:DAT TSU:STO THD:STA TAA TBUF Standard and Fast Mode Bus Timing Data. 2003 Microchip Technology Inc. MCP3221 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 INL (LSB) Positive INL Negative INL 0 100 INL (LSB) FIGURE 2-1: 200 300 2 I C Bus Rate (kHz) 3.5 4 VDD (V) 4.5 FIGURE 2-4: (VDD = 2.7V). 5 200 300 400 INL vs. Clock Rate 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 Positive INL Negative NL 2.5 5.5 3 3.5 4 4.5 5 5.5 VDD (V) FIGURE 2-2: INL vs. VDD - I2C™ Standard Mode (fSCL = 100 kHz). FIGURE 2-5: INL vs. VDD - I2C™ Fast Mode (fSCL = 400 kHz). 2 2 1.5 1.5 1 INL (LSB) 1 INL (LSB) 100 2 Negative INL 3 Negative INL 0 Positive NL 2.5 Positive INL I C Bus Rate (kHz) INL vs. Clock Rate. 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 400 INL (LSB) INL (LSB) Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion Mode (fSAMP = 22.3 ksps), TA = +25°C. 0.5 0 -0.5 0.5 0 -0.5 -1 -1 -1.5 -1.5 -2 -2 0 1024 2048 Digital Code FIGURE 2-3: INL vs. Code (Representative Part). 2003 Microchip Technology Inc. 3072 4096 0 1024 2048 3072 4096 Digital Code FIGURE 2-6: INL vs. Code (Representative Part, VDD = 2.7V). DS21732B-page 5 MCP3221 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 Positive INL INL (LSB) INL (LSB) Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion Mode (fSAMP = 22.3 ksps), TA = +25°C. Negative INL -50 -25 0 25 50 75 100 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 125 Positive NL Negative INL -50 -25 0 Temperature (°C) INL vs. Temperature. 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 FIGURE 2-10: (VDD = 2.7V). Positive DNL DNL (LSB) DNL (LSB) FIGURE 2-7: Negative DNL 0 100 200 300 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 400 100 DNL (LSB) FIGURE 2-11: (VDD = 2.7V). DNL (LSB) 4.5 VDD (V) FIGURE 2-9: DNL vs. VDD - I2C™ Standard Mode (fSCL = 100 kHz). 200 300 400 2 Negative DNL DS21732B-page 6 125 I C Bus Rate (kHz) DNL vs. Clock Rate. 3.5 100 Negative DNL 0 Positive DNL 2.5 75 Positive DNL 2 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 50 INL vs. Temperature I C Bus Rate (kHz) FIGURE 2-8: 25 Temperature (°C) 5.5 DNL vs. Clock Rate 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 Positive DNL Negative DNL 2.5 3 3.5 4 4.5 5 5.5 VDD (V) FIGURE 2-12: DNL vs. VDD - I2C™ Fast Mode (fSCL = 400 kHz). 2003 Microchip Technology Inc. MCP3221 Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion Mode (fSAMP = 22.3 ksps), TA = +25°C. DNL (LSB) DNL (LSB) 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 0 1024 2048 3072 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 0 4096 1024 2048 Digital Code Positive DNL Negative DNL -50 -25 0 25 50 75 100 125 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 Positive DNL Negative DNL -50 -25 Temperature (°C) 0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1 DNL vs. Temperature. Fast Mode (fSCL=100 kHz) 2.5 3 3.5 4.5 5 VDD (V) FIGURE 2-15: FIGURE 2-17: (VDD = 2.7V). Standard Mode (fSCL=400 kHz) 4 Gain Error vs. VDD. 2003 Microchip Technology Inc. 0 25 50 75 100 125 Temperature (°C) Offset Error (LSB) Gain Error (LSB) FIGURE 2-14: 4096 FIGURE 2-16: DNL vs. Code (Representative Part, VDD = 2.7V). DNL (LSB) DNL (LSB) FIGURE 2-13: DNL vs. Code (Representative Part). 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 3072 Digital Code 5.5 DNL vs. Temperature 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 fSCL = 100 kHz & 400 kHz 2.5 FIGURE 2-18: 3 3.5 4 VDD (V) 4.5 5 5.5 Offset Error vs. VDD. DS21732B-page 7 MCP3221 Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion Mode (fSAMP = 22.3 ksps), TA = +25°C. 3 Offset Error (LSB) Gain Error (LSB) 2 VDD = 2.7V 1 0 -1 -2 VDD = 5V -3 -50 -25 0 25 50 75 100 2 1.8 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0 125 VDD = 5V VDD = 2.7V -50 -25 0 Temperature (°C) Gain Error vs. Temperature. 100 90 80 70 60 50 40 30 20 10 0 FIGURE 2-22: Temperature. VDD = 5V SINAD (dB) SNR (dB) FIGURE 2-19: VDD = 2.7V 1 10 75 100 125 VDD = 5V VDD = 2.7V 1 10 Input Frequency (kHz) SNR vs. Input Frequency. FIGURE 2-23: SINAD vs. Input Frequency. 80 VDD = 5V 70 60 SINAD (dB) THD (dB) 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 50 Offset Error vs. 100 90 80 70 60 50 40 30 20 10 0 Input Frequency (kHz) FIGURE 2-20: 25 Temperature (°C) VDD = 5V VDD = 2.7V 50 VDD = 2.7V 40 30 20 10 0 1 10 -40 Input Frequency (kHz) FIGURE 2-21: DS21732B-page 8 THD vs. Input Frequency. -30 -20 -10 0 Input Signal Level (dB) FIGURE 2-24: Level. SINAD vs. Input Signal 2003 Microchip Technology Inc. MCP3221 12 11.95 11.9 11.85 11.8 11.75 11.7 11.65 11.6 11.55 11.5 12 11.5 VDD = 2.7V 11 ENOB (rms) ENOB (rms) Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion Mode (fSAMP = 22.3 ksps), TA = +25°C. VDD = 5V 10.5 10 9.5 9 2.5 3 3.5 4 4.5 5 5.5 1 10 VDD (V) FIGURE 2-25: 100 90 80 70 60 50 40 30 20 10 0 Input Frequency (kHz) FIGURE 2-28: ENOB vs. VDD. ENOB vs. Input Frequency. 10 VDD = 5V fSAMP = 5 6 ksps Amplitude (dB) SFDR (dB) -10 VDD = 2.7V -30 -50 -70 -90 -110 -130 1 0 10 500 FIGURE 2-26: SFDR vs. Input Frequency. 1000 1500 2000 2500 Frequency (Hz) Input Frequency (kHz) FIGURE 2-29: Spectrum Using I2C™ Standard Mode (Representative Part, 1 kHz Input Frequency). 250 10 200 -30 IDD (µA) Amplitude (dB) -10 -50 -70 -90 150 100 50 -110 0 -130 0 2000 4000 6000 Frequency (Hz) 8000 10000 FIGURE 2-27: Spectrum Using I2C™ Fast Mode (Representative Part, 1 kHz Input Frequency). 2003 Microchip Technology Inc. 2.5 3 3.5 4 4.5 5 5.5 VDD (V) FIGURE 2-30: IDD (Conversion) vs. VDD. DS21732B-page 9 MCP3221 200 180 160 140 120 100 80 60 40 20 0 100 90 80 70 60 50 40 30 20 10 0 IDDA (µA) IDD (µA) Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion Mode (fSAMP = 22.3 ksps), TA = +25°C. VDD = 5V VDD = 2.7V 0 100 200 300 2 I C Clock Rate (kHz) FIGURE 2-31: Rate. 0 IDDA (µA) IDD (µA) VDD = 5V 150 VDD = 2.7V 50 0 -50 -25 0 25 50 75 100 100 125 VDD = 5V VDD = 2.7V -50 -25 0 25 50 75 100 125 Temperature (°C) IDD (Conversion) vs. FIGURE 2-35: Temperature. 100 90 80 70 60 50 40 30 20 10 0 IDDA (Active Bus) vs. 60 50 IDDS (pA) IDDA (µA) 400 IDDA (Active Bus) vs. Clock 100 90 80 70 60 50 40 30 20 10 0 Temperature (°C) FIGURE 2-32: Temperature. 200 300 2 I C Clock Rate (kHz) FIGURE 2-34: Rate. 250 100 VDD = 2.7V 400 IDD (Conversion) vs. Clock 200 VDD = 5V 40 30 20 10 0 2.5 3 3.5 4 4.5 5 5.5 2.5 3 VDD (V) FIGURE 2-33: DS21732B-page 10 IDDA (Active Bus) vs. VDD. 3.5 4 4.5 5 5.5 VDD (V) FIGURE 2-36: IDDS (Standby) vs. VDD. 2003 Microchip Technology Inc. MCP3221 Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion Mode (fSAMP = 22.3 ksps), TA = +25°C. 2.1 Test Circuits 1000 100 VDD = 5V IDDS (nA) 10 1 0.1 10 µF 0.01 0.1 µF 2 kΩ 0.001 0.0001 -50 -25 0 25 50 75 100 Temperature (°C) FIGURE 2-37: Temperature. AIN 125 VIN 2 kΩ VDD SDA MCP3221 VSS SCL IDDS (Standby) vs. VCM = 2.5V 2 Analog Input Leakage (nA) 1.8 1.6 FIGURE 2-39: 1.4 Typical Test Configuration. 1.2 1 0.8 0.6 0.4 0.2 0 -50 -25 0 25 50 75 100 125 Temperature (°C) FIGURE 2-38: Temperature. Analog Input Leakage vs. 2003 Microchip Technology Inc. DS21732B-page 11 MCP3221 3.0 PIN FUNCTIONS TABLE 3-1: PIN FUNCTION TABLE Name 3.1 Function VDD +2.7V to 5.5V Power Supply VSS Ground AIN Analog Input SDA Serial Data In/Out SCL Serial Clock In VDD and VSS The VDD pin, with respect to VSS, provides power to the device as well as a voltage reference for the conversion process. Refer to Section 6.4, “Device Power and Layout Considerations”, for tips on power and grounding. 3.2 Analog Input (AIN) AIN is the input pin to the sample-and-hold circuitry of the Successive Approximation Register (SAR) converter. Care should be taken in driving this pin. Refer to Section 6.1, “Driving the Analog Input”. For proper conversions, the voltage on this pin can vary from VSS to VDD. DS21732B-page 12 3.3 Serial Data (SDA) SDA is a bidirectional pin used to transfer addresses and data into and out of the device. Since it is an opendrain terminal, the SDA bus requires a pull-up resistor to VDD (typically 10 kΩ for 100 kHz and 2 kΩ for 400 kHz SCL clock speeds). Refer to Section 6.2, “Connecting to the I2C Bus”, for more information. For normal data transfer, SDA is allowed to change only during SCL low. Changes during SCL high are reserved for indicating the START and STOP conditions. Refer to Section 5.1, “I2C Bus Characteristics”. 3.4 Serial Clock (SCL) SCL is an input pin used to synchronize the data transfer to and from the device on the SDA pin and is an open-drain terminal. Therefore, the SCL bus requires a pull-up resistor to VDD (typically 10 kΩ for 100 kHz and 2 kΩ for 400 kHz SCL clock speeds. Refer to Section 6.2, “Connecting to the I2C Bus”). For normal data transfer, SDA is allowed to change only during SCL low. Changes during SCL high are reserved for indicating the START and STOP conditions. Refer to Section 6.1, “Driving the Analog Input”. 2003 Microchip Technology Inc. MCP3221 4.0 DEVICE OPERATION 4.2 The MCP3221 employs a classic SAR architecture. This architecture uses an internal sample and hold capacitor to store the analog input while the conversion is taking place. At the end of the acquisition time, the input switch of the converter opens and the device uses the collected charge on the internal sample-and-hold capacitor to produce a serial 12-bit digital output code. The acquisition time and conversion is self-timed using an internal clock. After each conversion, the results are stored in a 12-bit register that can be read at any time. Communication with the device is accomplished with a 2-wire, I2C interface. Maximum sample rates of 22.3 ksps are possible with the MCP3221 in a continuous-conversion mode and an SCL clock rate of 400 kHz. 4.1 Digital Output Code The digital output code produced by the MCP3221 is a function of the input signal and power supply voltage, VDD. As the VDD level is reduced, the LSB size is reduced accordingly. The theoretical LSB size is shown below. EQUATION V DD LSB SIZE = -----------4096 VDD = Supply voltage The output code of the MCP3221 is transmitted serially with MSB first. The format of the code is straight binary. Conversion Time (tCONV) The conversion time is the time required to obtain the digital result once the analog input is disconnected from the holding capacitor. With the MCP3221, the specified conversion time is typically 8.96 µs. This time is dependent on the internal oscillator and is independent of SCL. 4.3 Acquisition Time (tACQ) The acquisition time is the amount of time the sample cap array is acquiring charge. The acquisition time is, typically, 1.12 µs. This time is dependent on the internal oscillator and independent of SCL. 4.4 Sample Rate Sample rate is the inverse of the maximum amount of time that is required from the point of acquisition of the first conversion to the point of acquisition of the second conversion. The sample rate can be measured either by single or continuous conversions. A single conversion includes a Start Bit, Address Byte, Two Data Bytes and a Stop bit. This sample rate is measured from one Start Bit to the next Start Bit. For continuous conversions (requested by the Master by issuing an acknowledge after a conversion), the maximum sample rate is measured from conversion to conversion or a total of 18 clocks (two data bytes and two Acknowledge bits). Refer to Section 5-2, “Device Addressing”. Output Code 1111 1111 1111 1111 1111 1110 (4095) (4094) 0000 0000 0011 (3) 0000 0000 0010 (2) 0000 0000 0001 (1) 0000 0000 0000 (0) .5 LSB 1.5 LSB 2.5 LSB FIGURE 4-1: AIN VDD-1.5 LSB VDD-2.5 LSB Transfer Function. 2003 Microchip Technology Inc. DS21732B-page 13 MCP3221 4.5 Differential Non-Linearity (DNL) In the ideal A/D converter transfer function, each code has a uniform width. That is, the difference in analog input voltage is constant from one code transition point to the next. Differential nonlinearity (DNL) specifies the deviation of any code in the transfer function from an ideal code width of 1 LSB. The DNL is determined by subtracting the locations of successive code transition points after compensating for any gain and offset errors. A positive DNL implies that a code is longer than the ideal code width, while a negative DNL implies that a code is shorter than the ideal width. 4.6 Integral Non-Linearity (INL) Integral nonlinearity (INL) is a result of cumulative DNL errors and specifies how much the overall transfer function deviates from a linear response. The method of measurement used in the MCP3221 A/D converter to determine INL is the “end-point” method. 4.7 Offset Error Offset error is defined as a deviation of the code transition points that are present across all output codes. This has the effect of shifting the entire A/D transfer function. The offset error is measured by finding the difference between the actual location of the first code transition and the desired location of the first transition. The ideal location of the first code transition is located at 1/2 LSB above VSS. 4.8 Gain Error The gain error determines the amount of deviation from the ideal slope of the A/D converter transfer function. Before the gain error is determined, the offset error is measured and subtracted from the conversion result. The gain error can then be determined by finding the location of the last code transition and comparing that location to the ideal location. The ideal location of the last code transition is 1.5 LSBs below full-scale or VDD. 4.9 Conversion Current (IDD) The average amount of current over the time required to perform a 12-bit conversion. 4.10 Active Bus Current (IDDA) The average amount of current over the time required to monitor the I2C bus. Any current the device consumes while it is not being addressed is referred to as “Active Bus” current. 4.11 Standby Current (IDDS) The average amount of current required while no conversion is occurring and while no data is being output (i.e., SCL and SDA lines are quiet). 4.12 I2C Standard Mode Timing I2C specification where the frequency of SCL is 100 kHz. 4.13 I2C Fast Mode Timing I2C specification where the frequency of SCL is 400 kHz. DS21732B-page 14 2003 Microchip Technology Inc. MCP3221 5.0 SERIAL COMMUNICATIONS 5.1 I2C Bus Characteristics The following bus protocol has been defined: • Data transfer may be initiated only when the bus is not busy. • During data transfer, the data line must remain stable whenever the clock line is high. Changes in the data line while the clock line is high will be interpreted as a START or STOP condition. Accordingly, the following bus conditions have been defined (refer to Figure 5-1). 5.1.1 BUS NOT BUSY (A) Both data and clock lines remain high. 5.1.2 START DATA TRANSFER (B) A high-to-low transition of the SDA line while the clock (SCL) is high determines a START condition. All commands must be preceded by a START condition. 5.1.3 STOP DATA TRANSFER (C) A low-to-high transition of the SDA line while the clock (SCL) is high determines a STOP condition. All operations must be ended with a STOP condition. 5.1.4 DATA VALID (D) The state of the data line represents valid data when, after a START condition, the data line is stable for the duration of the clock signal’s high period. The data on the line must be changed during the low period of the clock signal. There is one clock pulse per bit of data. SCL (A) (B) Each data transfer is initiated with a START condition and terminated with a STOP condition. The number of data bytes transferred between the START and STOP conditions is determined by the master device and is unlimited. 5.1.5 ACKNOWLEDGE Each receiving device, when addressed, is obliged to generate an acknowledge bit after the reception of each byte. The master device must generate an extra clock pulse which is associated with this acknowledge bit. The device that acknowledges has to pull down the SDA line during the acknowledge clock pulse in such a way that the SDA line is stable-low during the high period of the acknowledge-related clock pulse. Setup and hold times must be taken into account. During reads, a master device must signal an end of data to the slave by not generating an acknowledge bit on the last byte that has been clocked out of the slave (NAK). In this case, the slave (MCP3221) will release the bus to allow the master device to generate the STOP condition. The MCP3221 supports a bidirectional, 2-wire bus and data transmission protocol. The device that sends data onto the bus is the transmitter and the device receiving data is the receiver. The bus has to be controlled by a master device which generates the serial clock (SCL), controls the bus access and generates the START and STOP conditions, while the MCP3221 works as a slave device. Both master and slave devices can operate as either transmitter or receiver, but the master device determines which mode is activated. (D) (D) (C) (A) SDA START CONDITION FIGURE 5-1: DATA ADDRESS OR ACKNOWLEDGE ALLOWED TO CHANGE VALID STOP CONDITION Data Transfer Sequence on the Serial Bus. 2003 Microchip Technology Inc. DS21732B-page 15 MCP3221 Device Addressing 5.3 The address byte is the first byte received following the START condition from the master device. The first part of the control byte consists of a 4-bit device code, which is set to 1010 for the MCP3221. The device code is followed by three address bits: A2, A1 and A0. The default address bits are 1001. Contact the Microchip factory for additional address bit options. The address bits allow up to eight MCP3221 devices on the same bus and are used to determine which device is accessed. The eighth bit of the slave address determines if the master device wants to read conversion data or write to the MCP3221. When set to a ‘1’, a read operation is selected. When set to a ‘0’, a write operation is selected. There are no writable registers on the MCP3221. Therefore, this bit must be set to a ’1’ in order to initiate a conversion. The MCP3221 is a slave device that is compatible with the I2C 2-wire serial interface protocol. A hardware connection diagram is shown in Figure 6-2. Communication is initiated by the microcontroller (master device), which sends a START bit followed by the address byte. On completion of the conversion(s) performed by the MCP3221, the microcontroller must send a STOP bit to end communication. The last bit in the device address byte is the R/W bit. When this bit is a logic ‘1’, a conversion will be executed. Setting this bit to logic ‘0’ will also result in an “acknowledge” (ACK) from the MCP3221, with the device then releasing the bus. This can be used for device polling. Refer to Section 6.3, “Device Polling”, for more information. START Executing a Conversion This section will describe the details of communicating with the MCP3221 device. Initiating the sample-andhold acquisition, reading the conversion data and executing multiple conversions will be discussed. 5.3.1 INITIATING THE SAMPLE AND HOLD The acquisition and conversion of the input signal begins with the falling edge of the R/W bit of the address byte. At this point, the internal clock initiates the sample, hold and conversion cycle, all of which are internal to the ADC. tACQ + tCONV is initiated here Address Byte SCL 1 2 3 4 SDA 1 0 0 1 A2 A1 A0 R/W Start Bit FIGURE 5-3: Address Byte. 6 7 8 9 Address bits Initiating the Conversion, tACQ + tCONV is initiated here READ/WRITE Lower Data Byte (n) 17 18 19 20 21 22 23 24 25 26 R/W A SLAVE ADDRESS Device bits 5 ACK 5.2 0 1 0 Device Code 1 0 1 Address Bits(1) SDA D8 D7 D6 D5 D4 D3 D2 D2 D0 ACK 1 ACK SCL FIGURE 5-4: Initiating the Conversion, Continuous Conversions. Note 1: Contact Microchip for additional address bits. FIGURE 5-2: DS21732B-page 16 Device Addressing. 2003 Microchip Technology Inc. MCP3221 5.3.2 The input signal will initially be sampled with the first falling edge of the clock following the transmission of a logic-high R/W bit. Additionally, with the rising edge of the SCL, the ADC will transmit an acknowledge bit (ACK = 0). The master must release the data bus during this clock pulse to allow the MCP3221 to pull the line low (refer to Figure 5-3). READING THE CONVERSION DATA Once the MCP3221 acknowledges the address byte, the device will transmit four ‘0’ bits followed by the upper four data bits of the conversion. The master device will then acknowledge this byte with an ACK = Low. With the following 8 clock pulses, the MCP3221 will transmit the lower eight data bits from the conversion. The master then sends an ACK = high, indicating to the MCP3221 that no more data is requested. The master can then send a stop bit to end the transmission. For consecutive samples, sampling begins on the falling edge of the LSB of the conversion result, which is two bytes long. Refer to Figure 5-6 a for timing diagram. tACQ + tCONV is initiated here 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 SCL S T A R T 1 S SDA 0 0 FIGURE 5-5: A 2 1 Device bits 5.3.3 Upper Data Byte Address Byte A 1 A C K R / W A 0 0 0 0 0 D D D 11 10 9 S T O P Lower Data Byte A C D K 7 D 8 D 6 D 5 D 4 D 3 D 2 D 1 N A K D 0 P Address bits Executing a Conversion. CONSECUTIVE CONVERSIONS For consecutive samples, sampling begins on the falling edge of the LSB of the conversion result. See Figure 5-6 for timing. tACQ + tCONV is initiated here tACQ + tCONV is initiated here fSAMP = 22.3 ksps (fCLK = 400 kHz) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 SCL S T A R T SDA S 1 0 0 1 A2 A1 A0 Device bits FIGURE 5-6: Upper Data Byte (n) Address Byte R / W A C K 0 0 0 0 D D D 11 10 9 Lower Data Byte (n) D 8 A C K D 7 D 6 D 5 D 4 D 3 D 2 D 1 D 0 A C K 0 Address bits Continuous Conversion. 2003 Microchip Technology Inc. DS21732B-page 17 MCP3221 6.0 APPLICATIONS INFORMATION 6.1 Driving the Analog Input The MCP3221 has a single-ended analog input (AIN). For proper conversion results, the voltage at the AIN pin must be kept between VSS and VDD. If the converter has no offset error, gain error, INL or DNL errors, and the voltage level of AIN is equal to or less than VSS + 1/2 LSB, the resultant code will be 000h. Additionally, if the voltage at AIN is equal to or greater than VDD - 1.5 LSB, the output code will be FFFh. The analog input model is shown in Figure 6-1. In this diagram, the source impedance (RSS) adds to the internal sampling switch (RS) impedance, directly affecting the time required to charge the capacitor (CSAMPLE). Consequently, a larger source impedance increases the offset error, gain error and integral linearity errors of the conversion. Ideally, the impedance of the signal source should be near zero. This is achievable with an operational amplifier, such as the MCP6022, which has a closed-loop output impedance of tens of ohms. VDD RSS Sampling Switch VT = 0.6V AIN CPIN 7 pF VA VT = 0.6V SS RS = 1 kΩ CSAMPLE = DAC capacitance = 20 pF ILEAKAGE ±1 nA VSS Legend VA RSS AIN CPIN VT ILEAKAGE SS RS CSAMPLE = = = = = = = = = FIGURE 6-1: 6.2 signal source source impedance analog input pad analog input pin capacitance threshold voltage leakage current at the pin due to various junctions sampling switch sampling switch resistor sample/hold capacitance Analog Input Model, AIN. Connecting to the I2C Bus The I2C bus is an open-collector bus, requiring pull-up resistors connected to the SDA and SCL lines. This configuration is shown in Figure 6-2. The number of devices connected to the bus is limited only by the maximum bus capacitance of 400 pF. A possible configuration using multiple devices is shown in Figure 6-3. SDA SCL VDD PICmicro® Microcontroller PIC16F876 Microcontroller RPU RPU MCP3221 SDA AIN SCL 24LC01 EEPROM Analog Input Signal MCP3221 12-bit ADC TC74 Temperature Sensor RPU is typically: 10 kΩ for fSCL = 100 kHz 2 kΩ for fSCL = 400 kHz FIGURE 6-2: Bus. DS21732B-page 18 Pull-up Resistors on I2C FIGURE 6-3: Bus. Multiple Devices on I2C™ 2003 Microchip Technology Inc. MCP3221 6.3 Device Polling In some instances, it may be necessary to test for MCP3221 presence on the I2C bus without performing a conversion. This operation is described in Figure 6-4. Here we are setting the R/W bit in the address byte to a zero. The MCP3221 will then acknowledge by pulling SDA low during the ACK clock and then release the bus back to the I2C master. A stop or repeated start bit can then be issued from the master and I2C communication can continue. Address Byte 1 2 3 4 5 6 7 8 9 SDA 1 0 0 1 Start Bit Device bits Use of an analog ground plane is recommended in order to keep the ground potential the same for all devices on the board. Providing VDD connections to devices in a “star” configuration can also reduce noise by eliminating current return paths and associated errors (Figure 6-6). For more information on layout tips when using the MCP3221 or other ADC devices, refer to AN688, “Layout Tips for 12-Bit A/D Converter Applications”. ACK SCL Digital and analog traces should be separated as much as possible on the board, with no traces running underneath the device or the bypass capacitor. Extra precautions should be taken to keep traces with highfrequency signals (such as clock lines) as far as possible from analog traces. A2 A1A0 0 R/W Address bits VDD Connection Start Bit MCP3221 response FIGURE 6-4: 6.4 6.4.1 Device Power and Layout Considerations Device 3 POWERING THE MCP3221 VDD supplies the power to the device as well as the reference voltage. A bypass capacitor value of 0.1 µF is recommended. Adding a 10 µF capacitor in parallel is recommended to attenuate higher frequency noise present in some systems. VDD 0.1 µF VDD AIN MCP3221 Device 2 FIGURE 6-6: VDD traces arranged in a ‘Star’ configuration in order to reduce errors caused by current return paths. 6.4.3 VDD 10 µF Device 4 Device 1 Device Polling. SCL SDA RPU RPU To Microcontroller USING A REFERENCE FOR SUPPLY The MCP3221 uses VDD as both power and a reference. In some applications, it may be necessary to use a stable reference to achieve the required accuracy. Figure 6-7 shows an example using the MCP1541 as a 4.096V, 2% reference. 6.4.2 Powering the MCP3221. LAYOUT CONSIDERATIONS When laying out a printed circuit board for use with analog components, care should be taken to reduce noise wherever possible. A bypass capacitor from VDD to ground should always be used with this device and should be placed as close as possible to the device pin. A bypass capacitor value of 0.1 µF is recommended. 2003 Microchip Technology Inc. VDD 1 µF MCP1541 CL 4.096V Reference AIN VDD SCL MCP3221 SDA RPU To Microcontroller FIGURE 6-5: 0.1 µF VDD FIGURE 6-7: Stable Power and Reference Configuration. DS21732B-page 19 MCP3221 7.0 PACKAGING INFORMATION 7.1 Package Marking Information 5-Pin SOT-23A (EIAJ SC-74) Device 3 2 1 cdef 4 Part Number 5 Address Option SOT-23 MCP3221A0T-I/OT 000 EE MCP3221A1T-I/OT 001 EH MCP3221A2T-I/OT 010 EB MCP3221A3T-I/OT 011 EC MCP3221A4T-I/OT 100 ED MCP3221A5T-I/OT 101 S1 * MCP3221A6T-I/OT 110 EF MCP3221A7T-I/OT 111 EG MCP3221A0T-E/OT 000 GE MCP3221A1T-E/OT 001 GH MCP3221A2T-E/OT 010 GB MCP3221A3T-E/OT 011 GC MCP3221A4T-E/OT 100 GD MCP3221A5T-E/OT 101 GA * MCP3221A6T-E/OT 110 GF MCP3221A7T-E/OT 111 GG * Default option. Contact Microchip Factory for other address options. Legend: Note: * 1 2 3 4 Part Number code + temperature range Part Number code + temperature range Year and work week Lot ID In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information. Standard device marking consists of Microchip part number, year code, week code, and traceability code. DS21732B-page 20 2003 Microchip Technology Inc. MCP3221 5-Lead Plastic Small Outline Transistor (OT) (SOT23) E E1 p B p1 n D 1 α c A φ L β Units Dimension Limits n p Number of Pins Pitch Outside lead pitch (basic) Overall Height Molded Package Thickness Standoff § Overall Width Molded Package Width Overall Length Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic MIN p1 A A2 A1 E E1 D L φ c B α β .035 .035 .000 .102 .059 .110 .014 0 .004 .014 0 0 A2 A1 INCHES* NOM 5 .038 .075 .046 .043 .003 .110 .064 .116 .018 5 .006 .017 5 5 MAX .057 .051 .006 .118 .069 .122 .022 10 .008 .020 10 10 MILLIMETERS NOM 5 0.95 1.90 0.90 1.18 0.90 1.10 0.00 0.08 2.60 2.80 1.50 1.63 2.80 2.95 0.35 0.45 0 5 0.09 0.15 0.35 0.43 0 5 0 5 MIN MAX 1.45 1.30 0.15 3.00 1.75 3.10 0.55 10 0.20 0.50 10 10 Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0 254mm) per side. JEDEC Equivalent: MO-178 Drawing No. C04-091 2003 Microchip Technology Inc. DS21732B-page 21 MCP3221 NOTES: DS21732B-page 22 2003 Microchip Technology Inc. MCP3221 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. XX X /XX Device Address Options Temperature Range Package Device: Examples: a) b) MCP3221T: 12-Bit 2-Wire Serial A/D Converter (Tape and Reel) c) d) Temperature Range: Address Options: Package: I = -40°C to +85°C E = -40°C to +125°C XX e) A2 A1 A0 A0 = 0 0 0 A1 = 0 0 1 A2 = 0 1 0 A3 = 0 1 1 A4 = 1 0 0 A5 * = 1 0 1 A6 = 1 1 0 A7 = 1 1 1 f) g) h) a) b) c) * Default option. Contact Microchip factory for other address options d) OT = SOT-23, 5-lead (Tape and Reel) e) f) g) h) MCP3221A0T-I/OT: Industrial, A0 Address, Tape and Reel MCP3221A1T-I/OT: Industrial, A1 Address, Tape and Reel MCP3221A2T-I/OT: Industrial, A2 Address, Tape and Reel MCP3221A3T-I/OT: Industrial, A3 Address, Tape and Reel MCP3221A4T-I/OT: Industrial, A4 Address, Tape and Reel MCP3221A5T-I/OT: Industrial, A5 Address, Tape and Reel MCP3221A6T-I/OT: Industrial, A6 Address, Tape and Reel MCP3221A7T-I/OT: Industrial, A7 Address, Tape and Reel MCP3221A0T-E/OT: Extended, A0 Address, Tape and Reel MCP3221A1T-E/OT: Extended, A1 Address, Tape and Reel MCP3221A2T-E/OT: Extended, A2 Address, Tape and Reel MCP3221A3T-E/OT: Extended, A3 Address, Tape and Reel MCP3221A4T-E/OT: Extended, A4 Address, Tape and Reel MCP3221A5T-E/OT: Extended, A5 Address, Tape and Reel MCP3221A6T-E/OT: Extended, A6 Address, Tape and Reel MCP3221A7T-IE/OT: Extended, A7 Address, Tape and Reel Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. 2003 Microchip Technology Inc. DS21732B-page 23 MCP3221 NOTES: DS21732B-page 24 2003 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most l kely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your respons bility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, MPLAB, PIC, PICmicro, PICSTART, PRO MATE and PowerSmart are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, microID, MXDEV, MXLAB, PICMASTER, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Accuron, Application Maestro, dsPICDEM, dsPICDEM.net, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, InCircuit Serial Programming, ICSP, ICEPIC, microPort, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, PICC, PICkit, PICDEM, PICDEM.net, PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPIC, Select Mode, SmartSensor, SmartShunt, SmartTel and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. Serialized Quick Turn Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2003, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999 and Mountain View, California in March 2002. The Company’s quality system processes and procedures are QS-9000 compliant for its PICmicro® 8-bit MCUs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, non-volatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001 certified. DS21732B-page 25 2003 Microchip Technology Inc. M WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC Corporate Office Australia 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com Microchip Technology Australia Pty Ltd Marketing Support Division Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 Atlanta 3780 Mansell Road, Suite 130 Alpharetta, GA 30022 Tel: 770-640-0034 Fax: 770-640-0307 China - Beijing 2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 Microchip Technology Consulting (Shanghai) Co., Ltd., Beijing Liaison Office Unit 915 Bei Hai Wan Tai Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104 Chicago China - Chengdu 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Microchip Technology Consulting (Shanghai) Co., Ltd., Chengdu Liaison Office Rm. 2401-2402, 24th Floor, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-86766200 Fax: 86-28-86766599 Boston Dallas 4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 Detroit Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Kokomo 2767 S. Albright Road Kokomo, IN 46902 Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 Phoenix 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-4338 San Jose Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 Toronto 6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 China - Fuzhou Microchip Technology Consulting (Shanghai) Co., Ltd., Fuzhou Liaison Office Unit 28F, World Trade Plaza No. 71 Wusi Road Fuzhou 350001, China Tel: 86-591-7503506 Fax: 86-591-7503521 China - Hong Kong SAR Microchip Technology Hongkong Ltd. Unit 901-6, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 China - Shanghai Microchip Technology Consulting (Shanghai) Co., Ltd. Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 China - Shenzhen Microchip Technology Consulting (Shanghai) Co., Ltd., Shenzhen Liaison Office Rm. 1812, 18/F, Building A, United Plaza No. 5022 Binhe Road, Futian District Shenzhen 518033, China Tel: 86-755-82901380 Fax: 86-755-8295-1393 China - Qingdao Rm. B505A, Fullhope Plaza, No. 12 Hong Kong Central Rd. Qingdao 266071, China Tel: 86-532-5027355 Fax: 86-532-5027205 India Microchip Technology Inc. India Liaison Office Marketing Support Division Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O’Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062 Japan Microchip Technology Japan K.K. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934 Singapore Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan Microchip Technology (Barbados) Inc., Taiwan Branch 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 EUROPE Austria Microchip Technology Austria GmbH Durisolstrasse 2 A-4600 Wels Austria Tel: 43-7242-2244-399 Fax: 43-7242-2244-393 Denmark Microchip Technology Nordic ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45-4420-9895 Fax: 45-4420-9910 France Microchip Technology SARL Parc d’Activite du Moulin de Massy 43 Rue du Saule Trapu Ba iment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany Microchip Technology GmbH Steinheilstrasse 10 D-85737 Ismaning, Germany Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy Microchip Technology SRL Via Quasimodo, 12 20025 Legnano (MI) Milan, Italy Tel: 39-0331-742611 Fax: 39-0331-466781 United Kingdom Microchip Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44-118-921-5869 Fax: 44-118-921-5820 05/30/03 DS21732B-page 26 2003 Microchip Technology Inc.