Zarlink MA838 Single phase pulse width modulation waveform generator Datasheet

Obsolescence Notice
This product is obsolete.
This information is available for your
convenience only.
For more information on
Zarlink’s obsolete products and
replacement product lists, please visit
http://products.zarlink.com/obsolete_products/
JULY
1995
MA838
DS3798-3.1
MA838 FAMILY
SINGLE PHASE PULSE WIDTH MODULATION
WAVEFORM GENERATOR
The MA838 PWM generator has been designed to provide
waveforms for the control of variable speed AC machines,
uninterruptible power supplies and other forms of power
electronic devices which require pulse width modulation as a
means of efficient power control.
Two TTL level PWM outputs control the upper and lower
switches in an inverter arm. This is usually via an external
isolation and amplification stage.
Information contained within the pulse width modulated
sequences controls the wave shape, power frequency and
amplitude of the output waveform. Parameters such as the
carrier frequency, minimum pulse width and pulse delay time
may be defined during initialisation of the device. The pulse
delay time (underlap) controls the delay between turning on
and off the two power switches in the inverter, in order to
accommodate variations in the turn-on and turn-off times of
families of power devices.
The MA838 is easily controlled by a microprocessor and
its fully digital generation of PWM waveforms gives
unprecedented accuracy and temperature stability. Precision
pulse shaping capability allows optimum efficiency with any
power circuitry. The device operates as a stand-alone
microprocessor peripheral reading the power waveform directly
from an internal ROM and requiring microprocessor intervention
only when operating parameters need to be changed.
An 8-bit multiplexed data bus is used to receive addresses
and data from the microprocessor/controller. This is a standard
MOTEL™ bus, compatible with most microprocessors/
controllers.
FEATURES
■ Fully Digital Operation
■ Interfaces with most Microprocessors
■ Wide Power-Frequency Range
■ 12-Bit Frequency Control accuracy
■ Carrier Frequency Selectable up to 24kHz
■ Waveform Stored in Internal ROM
■ Double Edged Regular Sampling
■ Selectable Minimum Pulse Width and Underlap Time
■ DC Injection Braking
MOTEL is a registered trademark of Motorola corp. and Intel corp.
NOTE
* = Intel bus format
† = Motorola bus format
DP28
MP28/W
Fig.1 Pin connections (top view)
The power frequency is defined to 12 bits for high accuracy
and a zero setting is included in order to implement DC-injection
braking with no software overhead.
This family is functionally identical to the MA828 PWM
generator IC except that only one PWM channel is provided.
ORDERING INFORMATION
MA838-1 PLABA (Commercial, Plastic DIL)
MA838-2 PLABA (Commercial, Plastic DIL)
MA838-1 PLABD (Industrial, Plastic DIL)
MA838-2 PLABD (Industrial, Plastic DIL)
MA838-1 SLABA (Commercial, Plastic Small Outline)
MA838-2 SLABA (Commercial, Plastic Small Outline)
MA838-1 SLABD (Industrial, Plastic Small Outline)
MA838-2 SLABD (Industrial, Plastic Small Outline)
The MA838-1 and MA838-2 are the two standard waveform
options offered; refer to PRODUCT DESIGNATION section for
waveform specifications.
1
MA838
ABSOLUTE MAXIMUM RATINGS
Supply voltage, VDD
10V
Voltage on any pin
VSS-0.3V to VDD +0.3V
Current through any I/O pin
±10mA
Storage temperature (see note)
-65°C to +125°C
Operating temperature range (commercial) 0°C to +70°C
Operating temperature range (industrial)
-40°C to +85°C
Stresses above those listed in the Absolute Maximum
Ratings may cause permanent damage to the device. These
are stress ratings only and functional operation of the device at
these conditions, or at any other condition above those indicated
in the operations section of this specification, is not implied.
Exposure to Absolute Maximum Rating conditions for extended
periods may affect device reliability.
NOTE: These temperature ranges apply to all package types.
Many package types are available and extended temperature
ranges can be offered for some packages. Further information
is available on request.
DC ELECTRICAL CHARACTERISTICS
Test conditions (unless otherwise stated):
VDD = 5V±5%, Tamb = 25°C
Characteristic
Symbol
Min.
Typ.
Max.
Units
Input high voltage
VIH
2.0
-
-
V
Input low voltage
VIL
-
-
0.8
V
Input leakage current
IIN
-
-
10
µA
Output high voltage
VOH
4.0
>4.5
-
V
IOH = -4mA
Output low voltage
VOL
-
<0.2
0.4
V
IOH = 4mA
IDD (static)
IDD (dynamic)
-
<10
100
20
µA
mA
VDD
2.7
5.0
5.5
V
Symbol
Min.
Typ.
Max.
Units
Conditions
Clock frequency
fCLK
-
-
12.5
MHz
M:S ratio 1:1 ±20%
SET TRIP = 0
→ Outputs tripped
→ TRIP = 0
tTRIP
-
2/fCLK
2/fCLK
3/fCLK
3/fCLK
s
s
Supply current (static)
(dynamic)
Supply voltage
Conditions
VIN = VSS or VDD
all outputs open circuit
CLK = 10MHz
AC ELECTRICAL CHARACTERISTICS
Test conditions (unless otherwise stated):
VDD = 5V±5%, Tamb = 25°C
Characteristic
PRODUCT DESIGNATION
Two standard options exist, defining waveform shape.
These are designated MA838-1 and MA838-2 as follows:
MA838-1
Sine + third harmonic at one sixth the amplitude of the
fundamental:
x(t) = A [sin ( t) + 1 sin 3( t)]
6
2
MA838-2
Pure sinewave:
x(t) = A [sin ( t)]
Additional wave shapes can be implemented to order, provided
they are symmetrical about the 90°, 180° and 270° axes.
Contact your local GEC Plessey Semiconductors Customer
Service Centre for further details.
MA838
PIN DESCRIPTIONS
Pin No.
Name
Type
1
AD2
I
Multiplexed Address/Data
Function
Pin No.
12
Name
VSS
Type
Function
S
Negative Power Supply
2
AD3
I
Multiplexed Address/Data
13
PWMT
O
Top PWM Signal
3
AD4
I
Multiplexed Address/Data
14
SET TRIP
I
Set Output Trip
4
AD5
I
Multiplexed Address/Data
15
AD6
I
Multiplexed Address/Data
Intel
ALE
Motorola AS
I
5
Intel
Address Latch Enable
Motorola Address Strobe
6
AD7
I
Multiplexed Address/Data (MSB)
16
I
7
RST
I
Resets Internal Counters
Intel
RD
Motorola DS
Intel
Read Strobe
Motorola Data Strobe
8
CLK
I
Clock Input
17
I
9
TRIP
O
Output Trip Status
Intel
WR
Motorola R/W
Intel
Write Strobe
Motorola Read/Write Select
10
CS
I
Chip Select
18
VDD
S
Positive Power Supply
11
PWMB
O
Bottom PWM Signal
19
AD0
I
Multiplexed Address/Data(LSB)
20
AD1
I
Multiplexed Address/Data
Fig.2 MA838 internal block diagram
3
MA838
PWM
SWITCHING
INSTANTS
SAMPLING
POINTS
TRIANGLE WAVE AT
CARRIER FREQUENCY
+1
0
POWER
WAVEFORM AS
READ FROM
INTERNAL
ROM
-1
+1
RESULTING
PWM
WAVEFORM
0
-1
Fig.3 Asynchronous PWM generation with uniform or 'double-edged' regular sampling as used on the MA838
FUNCTIONAL DESCRIPTION
MICROPROCESSOR INTERFACE
An asynchronous method of PWM generation is used with
uniform or ‘double-edged’ regular sampling of the waveform
stored in the internal ROM as illustrated in Fig. 3. Two standard
waveshape options exist so that the device can be adapted to
particular applications (see PRODUCT DESIGNATION section
for details). In addition, any symmetrical waveshape may be
integrated on-chip, to order.
The triangle carrier wave frequency is selectable up to
24kHz (assuming the maximum clock frequency of 12.5MHz is
used), enabling ultrasonic operation for noise critical
applications. With 12.5MHz clock, power frequency ranges of
up to 4kHz are possible, with the actual output frequency
resolved to 12-bit accuracy within the chosen range in order to
give precise motor speed control and smooth frequency
changing.
PWM output pulses can be ‘tailored’ to the inverter
characteristics by defining the minimum allowable pulse width
(deletes all shorter pulses from the ‘pure’ PWM pulse train) and
the pulse delay (underlap) time without the need for external
circuitry. This gives cost advantages in both component savings
and in allowing the same PWM circuitry to be used for control
of a number of different systems simply by changing the
microprocessor software.
Power frequency amplitude control is also provided with an
overmodulation option to assist in rapid motor braking.
Alternatively, braking may be implemented by setting the
frequency to 0Hz. This is termed ‘DC injection braking’, in
which the rotation of the motor is opposed by allowing DC to
flow in the windings.
A trip input allows the PWM outputs to be shut down
immediately, overriding the microprocessor control in the event
of an emergency.
Other possible MA838 applications are as a waveform
generator as part of a switched-mode power supply (SMPS)
or an uninterruptible power supply (UPS). In such applications
the high carrier frequency allows a very small transformer to
be used.
The MA838 interfaces to the controlling microprocessor by
means of a multiplexed bus of the MOTEL format. This interface
bus has the ability to adapt itself automatically to the format and
timing of both MOTorola and IntEL interface buses (hence
MOTEL). Internally, the detection circuitry latches the status of
the DS/RD line when AS/ALE goes high. If the result is high
then the Intel mode is used; if the result is low then the Motorola
mode is used. This procedure is carried out each time that AS/
ALE goes high. In practice this mode selection is transparent
to the user. For bus connection and timing information refer to
the description relevant to the microprocessor/controller being
used.
Industry standard microprocessors such as the 8085, 8088,
etc. and microcontrollers such as the 8051, 8052 and 6805 are
all compatible with the interface on the MA838. This interface
consists of 8 data lines, AD0 - AD7 (write-only in this instance),
which are multiplexed to carry both the address and data
information, 3 bus control lines, labelled WR,RD and ALE in
Intel mode and R/W, DS and AS in Motorola mode, and a Chip
Select input CS, which allows the MA838 to share the same
bus as other microprocessor peripherals. It should be noted
that all bus timings are derived from the microprocessor and
are independent of the MA838 clock input.
4
Intel Mode (Fig. 4 and Table 1)
The address is latched by the falling edge of ALE. Data is
written from the bus into the MA838 on the rising edge of WR.
RD is not used in this mode because the registers in the MA838
are write only. However, this pin must be connected to RD (or
tied high) to enable the MA838 to select the correct interface
format.
Motorola Mode (Fig. 5 and Table 2)
The address is latched on the falling edge of the AS line.
Data is written from the bus into the MA838 (only when R/W is
low) on the falling edge of DS (providing CS is low).
MA838
Fig. 4 Intel bus timing definitions
Parameter
Fig. 5 Motorola bus timing definitions
Symbol
Min.
Units
ALE high period
t1
70
ns
Delay time, ALE to WR
Parameter
Symbol
Min.
Units
AS high period
t1
90
ns
t2
40
ns
Delay time, as low to DS high
t2
40
ns
WR low period
t3
200
ns
DS high period
t3
210
ns
Delay time, WR high to ALE high
t4
40
ns
Delay time, DS low to AS high
t4
40
ns
CS setup time
t8
20
ns
DS low period
t5
200
ns
CS hold time
t9
0
ns
DS high to R/W low setup time
t6
10
ns
Address setup time
t10
30
ns
R/W hold time
t7
10
ns
Address hold time
t15
30
ns
CS setup time
t8
20
ns
Data setup time
t11
t12
100
ns
CS hold time
t9
0
ns
25
ns
Address setup time
t10
30
ns
Address hold time
t15
30
ns
Write data setup time
t11
110
ns
Write data hold time
t12
30
ns
Data hold time
Table 1 Intel bus timings at VDD = 5V, TAMB = 25°C
CONTROLLING THE MA838
The MA838 is controlled by loading data into two 24-bit
registers via the microprocessor interface. These registers
are the initialisation register and the control register.
The initialisation register would normally be loaded prior to
the PWM outputs being activated and sets up the basic
operating parameters associated with the load and inverter.
This data would not normally be updated during PWM
operation.
The control register is used to control the PWM outputs
(and hence the load) during operation e.g., stop/start, speed
etc. and would normally be loaded and changed only after the
initialisation register has been loaded.
As the MOTEL bus interface is restricted to an 8-bit wide
format, data to be loaded into either of the 24-bit register is
first written to three 8-bit temporary registers R0, R1 and R2
before being transferred to the desired 24-bit register. The
data is accepted (and acted upon) only when transferred to
one of the 24-bit registers.
Table 2 Motorola bus timings at VDD = 5V, TAMB = 25°C
Transfer of data from the temporary registers to either the
initialisation register or the control register is achieved by a
write instruction to a dummy register. Writing to dummy register R3
results in data transfer from R0, R1 and R2 to the control register,
while writing to dummy register R4 transfers data from R0, R1
and R2 to the initialisation register. It does not matter what data
is written to the dummy registers R3 and R4 as they are not real
registers. It is merely the write instruction to either of these
registers which is acted upon in order to load the initialisation and
control registers.
AD2
AD1
AD0
Register
Comment
0
0
0
R0
Temporary register R0
0
0
1
R1
Temporary register R1
0
1
0
R2
Temporary register R2
0
1
1
R3
Transfers control data
1
0
0
R4
Transfers initialisation data
Table 3 MA838 register addressing
5
MA838
Initialisation Register Function
The 24-bit initialisation register contains parameters which,
under normal operation, will be defined during the power-up
sequence. These parameters are particular to the drive circuitry
used, and therefore changing these parameters during a PWM
cycle is not recommended. Information in this register should
only be modified while RST is active (i.e. low) so that the PWM
outputs are inhibited (low) during the updating process.
The parameters set in the initialisation register are as
follows:
Carrier frequency
Low carrier frequencies reduce switching losses whereas
high carrier frequencies increase waveform resolution and can
allow ultrasonic operation.
Power Frequency Range
This sets the maximum power frequency that can be carried
within the PWM output waveforms. This would normally be set
to a value to prevent the motor system being operated outside
its design parameters.
Pulse delay time ('underlap')
For each phase of the PWM cycle there are two control
signals, one for the top switch connected to the positive
inverter DC supply and one for the bottom switch connected to
the negative inverter DC supply. In theory, the states of these
two switches are always complementary. However, due to the
finite and non-equal turn-on and turn- off times of power
devices, it is desirable when changing the state of the output
pair, to provide a short delay time during which both outputs are
off in order to avoid a short circuit through the switching
elements.
Pulse deletion time
A pure PWM sequence produces pulses which can vary in
width between 0% and 100% of the duty cycle. Therefore, in
theory, pulse widths can become infinitesimally narrow. In
practice this causes problems in the power switches due to
storage effects and therefore a minimum pulse width time is
required. All pulses shorter than the minimum specified are
deleted.
Counter reset
This facility allows the internal power frequency counter of
the MA838 to be set to zero, disabling the normal frequency
control and giving a 50% output duty cycle.
Initialisation Register Programming
The initialisation register data is loaded in 8-bit segments into
the three 8-bit temporary registers R0-R2. When all the initialisation
data has been loaded into these registers it is transferred into the
24-bit initialisation register by writing to the dummy register R4.
CFS word
101 100 011 010 001 000
Value of n
32
16
8
4
2
1
Table 4 Values of clock division ratio n
The carrier frequency, fCARR , is then given by:
fCARR =
k
512 x n
where k = clock frequency and n = 1, 2, 4, 8, 16 or 32 (as set
by FRS)
Power frequency range selection
The power frequency range selected here defines the maximum
limit of the power frequency. The operating power frequency is
controlled by the 12-bit Power Frequency Select (PFS) word in the
control register but may not exceed the value set here.
The power frequency range is a function of the carrier
waveform frequency (fCARR ) and a multiplication factor m,
determined by the 3-bit FRS word. The value of m is determined
as shown in Table 5.
FRS word
110 101 100 011 010 001 000
Value of m
64
32
16
8
4
2
1
Table 5 Values of carrier frequency multiplicaion factor m
The power frequency range, fRANGE , is then given by:
f
fRANGE = CARR x m
384
where fCARR = carrier frequency and m = 1, 2, 4, 8, 16, 32 or
64 (as set by FRS).
Fig. 7 Temporary register R2
Pulse delay time
The pulse delay time affects all six PWM outputs by delaying
the rising edges of each of the outputs by an equal amount.
The pulse delay time is a function of the carrier waveform
frequency and pdy, defined by the 6-bit pulse delay time select
word (PDY). The value of pdy is selected as shown in Table 6.
PDY word
111111
111110
...etc...
000000
Value of pdy
1
2
...etc...
64
Table 6 Values of pdy
The pulse delay time, tpdy, is then given by:
Fig. 6 Temporary register R1
Carrier frequency selection
The carrier frequency is a function of the externally applied
clock frequency and a division ratio n, determined by the 3-bit
CFS word set during initialisation. The values of n are selected
as shown in Table 4.
6
tpdy =
pdy
fCARR x 512
where pdy = 1- 64 (as set by PDY) and fCARR = carrier
frequency.
MA838
Fig 8 shows the eftect of the pulse delay circuit.
It should be noted that as the pulse delay circuit follows the
pulse deletion circuit (see Fig. 2), the minimum pulse width
seen at the PWM outputs will be shorter than the pulse deletion
time set in the initialisation register. The actual shortest pulse
generated is given by tpd -tpdy.
The pulse deletion time, tpd , is a function of the carrier wave
frequency and pdt, defined by the 7-bit pulse deletion time word
(PDT). The value of pdt is selected as shown in Table 7.
PDT word
1111111 1111110
Value of pdt
1
2
...etc...
0000000
...etc...
128
Table 7 Values of pdt
The pulse deletion time, tpd, is then given by:
tpd =
pdt
fCARR x 512
where pdt = 1-128 (as set by PDT) and fCARR = carrier frequency.
Fig. 10 shows the effect of pulse deletion on a pure PWM
waveform.
Counter reset
When the CR bit is active (i.e., Iow) the internal power
frequency phase counter is set to 0 degrees. The power
frequency is then set to 0Hz and cannot be changed via the
normal frequency control.
Fig. 8 Effect of pulse delay on PWM pulse train
Fig. 9 Temporary register R0
Pulse deletion time
To eliminate short pulses the true PWM pulse train is
passed through a pulse deletion circuit. The pulse deletion
circuit compares pulse widths with the pulse deletion time set
in the initialisation register. lf a pulse (either +ve or -ve) is
greater than or equal in duration to the pulse deletion time, it is
passed through unaltered, otherwise the pulse is deleted.
Control Register Function
This 24-bit register contains the parameters that would
normally be modified during PWM cycles in order to control
the operation of the motor.
The parameters set in the control register are as follows:
Power frequency
Allows the power frequency of the PWM outputs to be
adjusted within the range specified in the initialisation register
Power frequency amplitude
By altering the widths of the PWM output pulses while
maintaining their relative widths, the amplitude of the power
waveform is effectively altered whilst maintaining the same
power frequency.
Overmodulation
Allows the output waveform amplitude to be doubled so
that a quasi-squarewave is produced. A combination of
overmodulation and a lower power frequency can be used to
achieve rapid braking in AC motors.
Output inhibit
Allows the outputs to be set to the low state while the PWM
generation continues internally. Useful for temporarily
inhibiting the outputs without having to to change other
register contents.
Fig. 10 The effect of the pulse deletion circuit
7
MA838
Control Register Programming
The control register should only be programmed once the
initialisation register contains the basic operating parameters
of the MA838.
As with the initialisation register, control register data is
loaded into the three 8-bit temporary registers R0 - R2. When
all the data has been loaded into these registers it is transferred
into the 24-bit control register by writing to the dummy register
R3. It is recommended that all three temporary registers are
updated before writing to R3 in order to ensure that a conformal
set of data is transferred to the control register for execution.
Overmodulation selection
The overmodulation bit OM is, in effect, the ninth bit (MSB) of
the amplitude word. When active (i.e., high) the output waveform
will be controlled in the 100% to 200% range by the amplitude
word.
The percentage amplitude control is now given by:
Overmodulated Amplitude = APOWER + 100%
where APOWER = the power amplitude
Fig. 11 Temporary register R0
Fig. 12 Temporary register R1
Power frequency selection
The power frequency is selected as a proportion of the
power frequency range (defined in the initialisation register) by
the 12-bit power frequency select word, PFS, allowing the
power frequency to be defined in 4096 equal steps. As the PFS
word spans the two temporary registers R0 and R1 it is
therefore essential, when changing the power frequency, that
both these registers are updated before writing to R3.
The power frequency (fPOWER ) is given by:
fPOWER
fRANGE
=
x pfs
4096
Fig. 13 Voltage waveforms as seen at the motor terminals,
showing the effect of setting the overmodulation bit
Amplitude selection
The power waveform amplitude is determined by scaling
the amplitude of the waveform samples stored in the internal
ROM by the value of the 8-bit amplitude select word (AMP).
The percentage amplitude control is given by:
A
Power Amplitude, APOWER =
x 100%
255
where A = decimal value of AMP.
where pfs = decimal value of the 12-bit PFS word and fRANGE
= power frequency range set in the initialisation register.
Output inhibit selection
When active (i.e., Iow) the output inhibit bit INH sets all the
PWM outputs to the off (low) state. No other internal operation
of the device is affected. When the inhibit is released the PWM
outputs continue immediately. Note that as the inhibit is asserted
after the pulse deletion and pulse delay circuits, pulses shorter
than the normal minimum pulse width may be produced initially.
8
Fig.14 Temporary register R2
MA838
POWER-UP C0NDITIONS
All bits in both the Initialisation and Control registers powerup in the low state. This means that Counter Reset (CR) is
active and a 50% duty cycle will be output from all PWM outputs
until further initialising action is taken. Holding RST low or
using the SET TRIP input will ensure that the PWM outputs
remain inactive (i.e., low) during this period.
MA838 PROGRAMMING EXAMPLE
The following example assumes that a master clock of
12·288 MHz is used (12·288 MHz crystals are readily available).
This clock frequency will allow a maximum carrier frequency of
24 kHz and a maximum power frequency of 4 kHz.
Initialisation Register Programming Example
A power waveform range of up to 250Hz is required with a
carrier frequency of 6kHz, a pulse deletion time of 10µs and an
underlap of 5µs.
1. Setting the carrier frequency
The carrier frequency should be set first as the power
frequency, pulse deletion time and pulse delay time are all
defined relative to the carrier frequency.
We must calculate the value of n that will give the required
carrier frequency:
k
fCARR =
512 x n
n=
k
512 x fCARR
=
12·288x10 6
512 x 6 x 10 3
=4
4. Setting the pulse deletion time
In setting the pulse deletion time (i.e., the minimum pulse
width) account must be taken of the pulse delay time, as the
actual minimum pulse width seen at the PWM outputs is equal
to tpd – tpdy.
Therefore, the value of the pulse deletion time must, in this
instance, be set 5·2µs longer than the minimum pulse length
required
Minimum pulse length required = 10µs
∴ tPD to be set to 10µs + 5·2µs = +15·2µs
Now,
tpd =
pdt
fCARR x 512
pdt = fpd x fCARR x 512
= 15·2 x 10 -6 x 6 x 10 3 x 512 = 46·7
Again, pdt must be an integer and so must be either rounded
up or down – the choice of which will depend on the application.
Assuming we choose in this case the value 46 for pdt, this gives
a value of tpd , of 15 µs and an actual minimum pulse width of
15 – 5·2µs = 9·8µs.
From Table 7, pdt = 46 corresponds to a value of PDT, the
7-bit word in temporary register R0 of 1010010.
The data which must be programmed into the three temporary
registers R0, R1 and R2 (for transter into the initialisation
register) in order to achieve the parameters in the example
given, is shown in Fig. 15.
From Table 4, n = 4 corresponds to a 3-bit CFS word of
010 in temporary register R1.
2. Setting the power frequency range
We must calculate the value of m that will give the required
power frequency:
f
fRANGE = CARR x m
384
m=
fRANGE x 384
fCARR
=
250 x 384
6 x 10 3
= 16
From Table 5, m = 16 corresponds to a 3-bit FRS word of
100 in temporary register R1.
3. Setting the pulse delay time
As the pulse delay time affects the actual minimum pulse
width seen at the PWM outputs, it is sensible to set the pulse
delay time before the pulse deletion time, so that the effect of
the pulse delay time can be allowed for when setting the pulse
deletion time.
We must calculate the value of pdy that will give the required
pulse delay time:
pdy
tpdy =
fCARR x 512
pdy = tpdy x fCARR x 512
= 5 x 10 -6 x 6 x 10 3 x 512 = 15·4
However, the value of pdy must be an integer. As the
purpose of the pulse delay is to prevent ‘shoot-through’ (where
both top and bottom arms of the inverter are on simultaneously),
it is sensible to round the pulse delay time up to a higher, rather
than a lower figure.
Thus, if we assign the value 16 to pdy this gives a delay time
of 5·2µs. From Table 6, pdy = 16 corresponds to a 6-bit PDY
word of 110000 in temporary register R2.
Fig. 15
Control Register Programming Example
The control register would normally be updated many times
while the motor is running, but just one example is given here.
It is assumed that the initialisation register has already heen
programmed with the parameters given in the previous example.
A power waveform of 100Hz is required with a PWM
waveform amplitude of 80% of that stored in the ROM. The
outputs should be enabled and no overmodulation is required.
9
MA838
1. Setting the power frequency
The power frequency, fPOWER , can be selected to 12-bit
accuracy (i.e 4096 equal steps) from 0Hz to fRANGE as defined
in the initialisation register. In this case, with fRANGE = 250Hz,
the power frequency can be adjusted in increments of 0·06Hz.
pfs =
f
fPOWER = RANGE x pfs
4096
fPOWER x 4096
100 x 4096
=
= 1638·4
fRANGE
250
We can only have pfs as an integer, so if we assign pfs =
1638 this gives fPOWER = 99.97 Hz.The 12-bit binary equivalent
of this value gives a PFS word of 011001100110 in temporary
registers R0 and R1.
2. Setting overmodulation, output inhibit
Overmodulation is not required therefore OM = 0.
Output inhibit should be inactive (i e., the outputs should be
active), therefore INH= 1.
These bits are all set in temporary register R1.
3. Setting the power waveform amplitude
A
APOWER =
A=
225
APOWER x 255
=
x 100%
80 3x 255
= 204
100
100
The 8-bit binary equivalent of this value gives an AMP word
of 11001100 in temporary register R2. The data which must be
programmed into the three temporary registers R0, R1 and R2
(for transfer into the control register) in order to achieve the
parameters in the example given, is shown in Fig. 16.
Fig. 16
Fig. 17 Typical MA838 programming routine
10
MA838
HARDWARE INPUT/OUTPUT FUNCTIONS
Set Output Trip (SET TRIP input)
The SET TRIP input is provided separately from the
microprocessor interface in order to allow an external source
to override the microprocessor and provide a rapid shutdown
facility. For example, logic signals from overcurrent sensing
circuitry or the microprocessor ‘watchdog’ might be used to
activate this input.
When the SET TRIP input is taken to a logic high, the output
trip latch is activated. This results in the TRIP output and the
PWM outputs being latched low immediately. This condition
can only be cleared by applying a reset cycle to the RST input.
It is essential that when not in use this pin is tied low and
isolated from potential sources of noise; on no account should
it be left floating.
SET TRIP is latched internally at the master clock rate in
order to reduce noise sensitivity.
Waveform segment
Sample number
0°- 30°
0 - 127
30·23°- 60°
128 - 255
60·23°- 89·77°
256 - 383
Table 8 90° of the 360° cycle is divided into 384 8-bit
samples
Output Trip Status ( TRIP output)
The TRIP output indicates the status of the output trip latch
and is active low.
Reset (RST input)
The RST input performs the following functions when active
(low):
1. PWM outputs are forced low (if not already low) thereby
turning off the drive switches.
2. All internal counters are reset to zero (this corresponds to 0°
for the red phase output).
3. The rising edge of RST reactivates the PWM outputs
resetting the output trip and setting the TRIP output high –
assuming that the SET TRIP input is inactive (i.e. Iow).
Clock (CLK input)
The CLK input provides a timing reference used by the
MA838 for all timings related to the PWM outputs. The
microprocessor interface, however, derives all its timings from
the microprocessor and therefore the microprocessor and the
MA838 may be run either from the same or from different
clocks.
Fig. 18 90° sample of typical power waveform
WAVEFORM DEFINITION
The waveform amplitude data used to construct the PWM
output sequence is read from the internal 384 x 8 ROM. This
contains the 90° span of the waveform as shown in Fig. 18.
Each successive 8-bit sample linearly represents the
instantaneous amplitude of the waveform. It is assumed that
the waveform is symmetrical about the 90°, 180° and 270°
axes.The MA828 reconstructs the full 360° waveform by reading
the 0°-90° section held in ROM and assigning negative values
for the second half of the cycle.
The 384 8-bit samples are regularly spaced over the 0° to
90° span, giving an angular resolution of approximately 0·23°.
11
MA838
PACKAGE DETAILS
Dimensions are shown thus: mm (in). For further package information, please contact your local Customer Service Centre.
HEADQUARTERS OPERATIONS
GEC PLESSEY SEMICONDUCTORS
Cheney Manor, Swindon,
Wiltshire, United Kingdom SN2 2QW.
Tel: (01793) 518000
Fax: (01793) 518411
GEC PLESSEY SEMICONDUCTORS
P.O. Box 660017
1500 Green Hills Road,
Scotts Valley, California 95067-0017,
United States of America.
Tel: (408) 438 2900
Fax: (408) 438 5576
CUSTOMER SERVICE CENTRES
• FRANCE & BENELUX Les Ulis Cedex Tel: (1) 69 18 90 00 Fax: (1) 64 46 06 07
• GERMANY Munich Tel: (089) 3609 06-0 Fax: (089) 3609 06-55
• ITALY Milan Tel: (02) 66040867 Fax: (02) 66040993
• JAPAN Tokyo Tel: (03) 5276-5501 Fax: (03) 5276-5510
• NORTH AMERICA Scotts Valley, USA Tel: (408) 438 2900 Fax: (408) 438 7023
• SOUTH EAST ASIA Singapore Tel: (65) 3827708 Fax: (65) 3828872
• SWEDEN Stockholm, Tel: 46 8 702 97 70 Fax: 46 8 640 47 36
• TAIWAN, ROC Taipei, Tel: 886 2 5461260 Fax: 886 2 7190260
• UK, EIRE, DENMARK, FINLAND & NORWAY
Swindon Tel: (01793) 518510 Fax: (01793) 518582
These are supported by Agents and Distributors in major countries world-wide.
© GEC Plessey Semiconductors 1995 Publication No. DS3798 Issue No. 3.1 July 1995
TECHNICAL DOCUMENTATION - NOT FOR RESALE. PRINTED IN UNITED KINGDOM.
This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded
as a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company
reserves the right to alter without prior notice the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee
that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure
that any publication or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury
or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request.
12
Similar pages