CP1000 THRU CP1008 SINGLE-PHASE SILICON BRIDGE VOLTAGE - 50 to 800 Volts CURRENT - P.C. MTG 3A, HEAT-SINK MTG 10A FEATURES l Surge overload rating—200 Amperes peak l Low forward voltage drop and reverse leakage l l Small size, simple installation Plastic package has Underwriter Laboratory l Flammability Classification 94V-O Reliable low cost construction utilizing molded CP-10 plastic technique MECHANICAL DATA Case: Molded plastic with heatsink integrally mounted in the bridge encapsulation Terminals: Leads solderable per MIL-STD-202, Method 208 Weight: 0.21 ounce, 6.1 grams MACXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS At 25 ¢J ambient temperature unless otherwise noted; resistive or inductive load at 60Hz . Max Recurrent Peak Rev Voltage Max Bridge Input Voltage RMS Max Average Rectified Output at TC=50 ¢J * See Fig. 2 at TC=100 ¢J * at TA=50 ¢J ** Peak One Cycle Surge Overload Current Max Forward Voltage Drop per element at 5.0A DC & 25 ¢J . See Fig. 3 Max Rev Leakage at rated Dc Blocking Voltage per element at 25 ¢J See Fig 4 at100 ¢J CP1000 CP1001 CP1002 CP1004 CP1006 CP1008 UNITS 50 100 200 400 600 800 V 35 70 140 280 420 560 V 10.0 A 3.0 A 3.0 Typical junction capacitance per leg (Note 4) CJ 2 I t Rating for fusing ( t<8.3ms) Typical Thermal Resistance (Note 2) R £KJA Typical Thermal Resistance (Note 3) R £KJC Operating Temperature Range Storage Temperature Range 200 1.1 A V 10.0 1.0 £g A mA PF 2 AS ¢J /W 200 164 25 5 -55 TO +125 -55 TO +150 NOTES: * Unit mounted on metal chassis. ** Unit mounted on P.C. board. 1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw. 2. Units Mounted in free air, no heatsink. P.C.B at 0.375”(9.5mm) lead length with 0.5 ¡Ñ 0.5” (12 ¡Ñ 12mm)copper pads. 3. Units Mounted on a 3.0 ¡Ñ 3.0” ¡Ñ 0.11” thick (7.5 ¡Ñ 7.5 ¡Ñ 0.3cm) AL plate heatsink. 4. Measured at 1.0MHZ and applied reverse voltage of 4.0 volts. ¢J ¢J RATING AND CHARACTERISTIC CURVES 200 OUTPUT CURRENT AMPERES FORWARD SURGE CURRENT, AMPERES pk (HALF SINE WAVE) CP1000 THRU CP1008 160 120 80 T A = 105 ¢J 40 0 1 2 6 10 20 40 60 100 10 METAL HEATSINK 8 6 4 P.C. BOARD 2 0 0 50 100 150 Fig. 1-NON-RECURRENT SURGE RATING Fig. 2-DERATING CURVE FOR OUTPUT RECTIFIED CURRENT 5 4 3 2 1 .9 .8 .7 .5 TYPICAL DISTRIBUTION .3 .2 .1 .07 MEDIAN .05 .03 .02 .01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 INSTANTANEOUS FWD VOLTAGE, VOLTS Fig. 3-TYPICAL FORWARD CHARACTERISTICS(25 ¢J) INSTANTANEOUS REVERSE CURRENT, £g A AMBIENT TEMPERATURE, ¢J INSTANTANEOUS FWD CURRENT, AMPERES NO. OF CYCLES AT 60Hz 100 10 25 ¢J 1 0 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE Fig. 4-REVERSE CHARACTERISTICS