ACDC 6501200 Watts MHP Series xppower.com • Rugged Construction • Variable Fan Speed for Noise Reduction • 20 ºC to +70 ºC Operation • AC OK, Remote On/Off and Active Current Share • 5 V Standby • Screw Terminals • 3 Year Warranty Specification Input • 650 W: 80-264 VAC, derate output power 10% <90 VAC, and 20% <85 VAC, 1000 W: 85-264 VAC, derate output power 10% <90 VAC Input Frequency • 47-63 Hz Input Current • 650 W: 6.5 A at 115 VAC typical, 3.2 A at 230 VAC full load, 1000 W: 10.9 A at 115 VAC typical, 5.1 A at 230 VAC full load Inrush Current • 650 W: 40 A max at 264 VAC 1000 W: 60 A max at 264 VAC Power Factor • >0.9 Earth Leakage Current • 250 µA max at 264 VAC/60 Hz Input Protection • 650 W: T16 A/250 V, 1000 W: T20 A/250 V internal fuse in line and neutral Input Voltage Output • 12-48 VDC (see tables) • ±10% V1 • 650 W: ±1% V1, ±5% V3, 1000 W: ±1% V1, ±5% V2 Minimum Load • No minimum load required Start Up Delay • 500 ms max Start Up Rise Time • 50 ms typical Hold Up Time • 20 ms minimum Drift • ±0.2% after 20 min warm up Line Regulation • ±0.5% Load Regulation • 650 W: ±1% V1, ±5% V3, 1000 W: ±1% V1, ±5% V2 Transient Response • 4% max. deviation, recovery to within 1% in 500 µs for a 50-75-50% load change Ripple & Noise • 1% pk-pk V1, 20 MHz bandwidth Overvoltage Protection • 115-145% Vnom, recycle input to reset Overload Protection • 110-140%, V1 only Overtemperature • Auto reset Protection Short Circuit Protection • Constant current characteristic Temp. Coefficient • 0.05% / °C Remote Sense • Compensates for 0.5 V total voltage drop Remote On/Off • Uncommitted isolated optocoupler diode, powered diode inhibits V1 and fan supply (1) Current Share • Single wire current share (1) Output Voltage Output Voltage Trim Initial Set Accuracy (1) See longform datasheet for more information General Efficiency Isolation Switching Frequency Power Density Signals MTBF • 85% typical • 4000 VAC In to Out, 2 x MOPP, 1500 VAC In to Earth, 1 x MOPP, 500 VDC Out to Earth • PFC 70 kHz, main converter 200 kHz, standby 130 kHz typical • 650 W: 8.2 W/in3,1000 W: 8.9 W/in3 • AC OK, remote on/off, current share (1) • 260 KHrs to MIL-HDBK-217F at 25 °C, GB Environmental Operating Temperature • -20 °C to +70 °C, derate linearly from +50 °C at 2.5% / °C to 50% at +70 °C, 1000 W: -40 °C start up Cooling • 650 W: Forced cooled, ‘-TF’ & ‘-EF’ models have integral dual voltage level fan, which is load dependant, U Channel requires 5.5 m/s minimum airflow, 1000 W: Forced cooled via integral quad voltage level fan which is load dependant (1) Operating Humidity • 95% RH, non-condensing Storage Temperature • -40 °C to +85 °C Operating Altitude • 3000 m Shock • 30 g pk, half sine, 6 axes Vibration • 2 g rms, 5 Hz to 500 kHz, 3 axes EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Dips & Interruptions Safety Approvals • EN55022/ENN55011 class B conducted EN55022/EN55011 class A radiated • EN61000-3-2 class A, 650 W: class C for loads ≥20% 1000 W: class C for loads ≥10% • EN61000-3-3 • EN61000-4-2, level 3 contact, level 3 air, Perf Criteria A • EN61000-4-3, level 3 Perf Criteria A • EN61000-4-4, level 3 Perf Criteria A • EN61000-4-5, installation class 3, Perf Criteria A • EN61000-4-6, level 3, Perf Criteria A • EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms, Perf Criteria A, B, B, EN60601-1-2, 30% 500 ms, 60% 100 ms, 100% 10 ms, 100% 5000 ms, Perf Criteria A, A, A, B. Consult longform for 115 VAC operation • IEC60601-1 CB report, CSA 22.2 No.60601-1, ANSI/AAMI ES60601-1, TUV, EN60601-1 Including Risk Management Output Voltage V1 12 15 24 28 36 48 Output Current V1 V V V V V V 50 40 27 23 18 13.5 Fan Supply V2(4) A A A A A A 12 12 12 12 12 12 V V V V V V / / / / / / 0.5 0.5 0.5 0.5 0.5 0.5 Standby Supply V3 A A A A A A 5 5 5 5 5 5 V V V V V V / / / / / / 0.2 0.2 0.2 0.2 0.2 0.2 Output Power(3) A A A A A A 607 607 655 655 655 655 Model Number(1,2) W W W W W W MHP650PS12-EF†^ MHP650PS15-EF†^ MHP650PS24-EF†^ MHP650PS28-EF†^ MHP650PS36-EF†^ MHP650PS48-EF†^ Notes 1. For top fan version replace ‘-EF’ in model number with ‘-TF’, e.g. MHP650PS12-TF 2. For U Channel version remove suffix. 3. U Channel models require a minimum of 5.5 m/s airflow from the system. 4. Not available for ‘-TF’ and ‘-EF’ models as used by integral fan. † Available from Farnell & element14. See pages 284-290. ^ Available from Newark. See pages 291-296 Mechanical Details End Fan (See Longform Datasheet for UChannel Version) Standard Terminal Block, M4 Screw, 6 Pins, 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) Vo+ L E N Vo- Standard Terminal Block, M3.5 Screw 3 Pins 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) 2.49 (63.3) V1 Adjustment Output On, LED 9.18 (233.2) 2 x M3 THD both side faces 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) 2.50 (63.5) AIRFLOW Pin 2 Pin 1 Pin 10 Pin 9 1.95 (49.5) J2: Logic Connector 8.00 (203.2) 2.86 (72.6) 4.00 (101.6) CL 4 x M3 THD 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) 6.53 (165.8) 0.87 (22.2) Notes 1. Dimensions shown in inches (mm). 2. Weight: 2.8 lb (1.27 kg). 3. J2 Mating plug: JST part no. PHDR-10VS, contact: 26-22 AWG JST part no. SPHD-001T-P0.5. Pin 1 2 3 4 5 6 7 8 9 10 J2 Logic Connector (JST B10B-PHDSS) Function + Sense - Sense AC OK/Power Fail - Sense Current Share Current Share + Inhibit (Anode) - Inhibit (Cathode) +5 V Standby (V3) 5 V Standby Return (V3) ACDC MHP650 Models and Ratings Top Fan (Suffix TF) Standard Terminal Block, M3.5 Screw 3, Pins 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) Standard Terminal Block, M4 Screw, 6 Pins, 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) Vo+ L E N Vo- ACDC MHP650 Mechanical Details V1 Adjustment Output On, LED 2.50 (63.5) 8.00 (203.2) 2.58 (65.5) AIRFLOW 2 x M3 THD both side faces 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) 1.95 (49.5) Pin 2 Pin 1 Pin 10 pin 9 J2: Logic Connector 2.86 (72.6) Pin 1 2 3 4 5 6 7 8 9 10 4.00 (101.6) 4 x M3 THD 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) 0.87 (22.2) 6.53 (165.8) Notes 1. Dimensions shown in inches (mm). 2. Weight: 2.8 lb (1.27 kg). 3. J2 Mating plug: JST part no. PHDR-10VS, contact: 26-22 AWG JST part no. SPHD-001T-P0.5. J2 Logic Connector (JST B10B-PHDSS) Function + Sense - Sense AC OK/Power Fail - Sense Current Share Current Share + Inhibit (Anode) - Inhibit (Cathode) +5 V Standby (V3) 5 V Standby Return (V3) Signals AC OK/Power Fail Remote On/Off (Inhibit) INHIBIT HI POWER SUPPLY Max 12 V 20 mA 5 V Standby Pin 9 5 V Standby Pin 9 5 V Standby Pin 9 2-5 mA 100 R 2-5 mA Inhibit Hi Pin 7 AC OK Collector Pin 3 AC OK Emitter Pin 2 (-sense) POWER SUPPLY 800 R 330R INHIBIT LOW 800 R Transistor On (<0.8 V): AC NOT OK Transistor Off (>4.5 V): AC OK Inhibit Lo Pin 8 5 V Standby Return Pin 10 5 V Standby Return Pin 10 Chassis J2 Logic Connector J2 Logic Connector Signal High: Power Supply OFF Low or Floating: Power Supply ON For U Channel and Thermal Considerations please see longform datasheet. 100 R Inhibit Hi Pin 7 Inhibit Lo Pin 8 5 V Standby Return Pin 10 POWER SUPPLY Chassis J2 Logic Connector Signal High: Power Supply ON Low or Floating: Power Supply OFF Output Voltage V1 Output Current V1 <180 VAC Output Power Standby Supply V2 >180 VAC <180 VAC Model Number >180 VAC 12 V 83.0 A 5 V / 1.0 A 1000 W MHP1000PS12†^ 15 V 67.0 A 5 V / 1.0 A 1010 W MHP1000PS15†^ 24 V 42.0 A 50.0 A 5 V / 1.0 A 1013 W 1200 W MHP1000PS24†^ 28 V 36.0 A 43.0 A 5 V / 1.0 A 1013 W 1200 W MHP1000PS28†^ 36 V 28.0 A 34.0 A 5 V / 1.0 A 1013 W 1200 W MHP1000PS36†^ 48 V 21.0 A 25.0 A 5 V / 1.0 A 1013 W 1200 W MHP1000PS48†^ † Available from Farnell & element14. See pages 284-290. ^ Available from Newark. See pages 291-296 Mechanical Details VO+ VO- Standard Terminal Block, M6 Screw, 4 Pins 0.62 (16.0) center Torque 26.0 lbs-in (2.94 Nm) 5.90 (149.8) 2.91 (73.9) Output On, LED A V1 Adjustment N 1.47 (37.4) L 2.40 (61.0) 9.48 (240.9) 1.20 (30.5) 9.55 (242.64) Standard Terminal Block, M4 Screw 3 Pins 0.37 (9.5) center Torque 10.62 lbs-in (1.2 Nm) 9.41 (238.9) 4 x M4-0.7 THD both side faces 0.15 (3.8) max screw penetration max torque 10.62 lbs-in (1.2 Nm) B B Airflow 1.20 (30.5) 4 x M4-0.7 THD both side faces 0.15 (3.8) max screw penetration max torque 10.62 lbs-in (1.2 Nm) B B 4.50 (114.3) CL Pin 2 Pin 1 Pin 10 Pin 9 B B Detail A J3: Logic Connector 6.70 (170.2) 1.33 (33.8) Notes 1. Dimensions shown in inches (mm). 2. Weight: 4.6 lb (2.08 kg) 3. J3 Mating plug: JST part no. PHDR-10VS, contact: 26-22 AWG JST part no. SPHD-001T-P0.5. J3 Logic Connector (JST B10B-PHDSS) Pin Function 1 + Sense 2 - Sense 3 AC OK/Power Fail 4 - Sense 5 Current Share 6 Current Share 7 + Inhibit 8 - Inhibit 9 +5 V Standby 10 -5 V Standby 22-Feb-13 ACDC MHP1000 Models and Ratings