Maxim MAX14850 Six-channel digital isolator Datasheet

19-6161; Rev 0; 3/12
EVALUATION KIT AVAILABLE
MAX14850
Six-Channel Digital Isolator
General Description
The MAX14850 is a six-channel digital isolator utilizing
Maxim’s proprietary process technology, whose monolithic design provides a compact and low-cost transfer
of digital signals between circuits with different power
domains. The technology enables low power consumption
and stable high-temperature performance.
The four unidirectional channels are each capable of
DC to 50Mbps, with two of the four channels passing
data across the isolation barrier in each direction. The
two bidirectional channels are open drain and each is
capable of data rates from DC to 2Mbps.
Independent 3.0V to 5.5V supplies on each side of the
isolator also make it suitable for use as a level translator.
The MAX14850 can be used for isolating SPI busses, I2C
busses with clock stretching, RS-232, RS-485/RS-422
busses, and general-purpose isolation. When used as
a bus isolator, extra channels are available for power
monitoring and reset signals.
Benefits and Features
S Protection from High-Voltage Environments
 600VRMS Isolation for 60 Seconds
 Short-Circuit Protection on Unidirectional
Outputs
S Complete Digital Isolation Solution
 Four Unidirectional Signal Paths: 2-In/2-Out
 Two Bidirectional Open-Drain Signal Paths
 50Mbps (max) Unidirectional Data Rate
 2Mbps (max) Bidirectional Data Rate
S Compatible with Many Interface Standards
 I2C With Clock Stretching
 SPI
 RS-232, RS-422/RS-485
 SMBus, PMBus Interfaces
Ordering Information appears at end of data sheet.
The MAX14850 is available in a narrow body,16-pin SO
(10mm x 4mm) package. The SO package is specified
over the -40NC to +125NC automotive temperature range.
Applications
Typical Operating Circuits
Industrial Control Systems
I2C, SPI, SMBus, PMBusK Interfaces
Isolated RS-232, RS-485/RS-422
0.1µF
3.3V
Telecommunication Systems
0.1µF
VCCA
Battery Management
Medical Systems
RPUA
RPUA
MAX14850
RPUB
RPUB
I/OA1
I/OB1
RST
GPIO2
I/OA2
I/OB2
CS
µC SCLK
INA1
OUTB1
SCLK ADC
MOSI
INA2
OUTB2
MOSI
MISO
OUTA1
INB1
MISO
OUTA2
INB2
VCCB MONITOR
GNDA
PMBus is a trademark of SMIF, Inc.
VCCB
GPIO1
GPIO3
For related parts and recommended products to use with this part,
refer to: www.maxim-ic.com/MAX14850.related
5V
GNDB
600VRMS
ISOLATION
Typical Operating Circuits continued at end of data sheet.
����������������������������������������������������������������� Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX14850
Six-Channel Digital Isolator
ABSOLUTE MAXIMUM RATINGS
VCCA to GNDA.........................................................-0.3V to +6V
VCCB to GNDB.........................................................-0.3V to +6V
OUTA1, OUTA2 to GNDA...................... -0.3V to (VCCA + 0.3V)
OUTB1, OUTB2 to GNDB...................... -0.3V to (VCCB + 0.3V)
INB1, INB2, I/OA1, I/OA2 to GNDA.........................-0.3V to +6V
INA1, INA2, I/OB1, I/OB2 to GNDB.........................-0.3V to +6V
Short-Circuit Duration (OUTA_ to GNDA or
VCCA, OUTB_ to GNDB or VCCB)..........................Continuous
Continuous Current (I/OA_, I/OB_) Pin............................. Q50mA
Continuous Power Dissipation (TA = +70NC)
SO (derate 13.3mW/NC above +70NC)..................1067mW
Operating Temperature Range......................... -40NC to +125NC
Junction Temperature......................................................+150NC
Storage Temperature Range............................. -65NC to +150NC
Lead Temperature (soldering, 10s).................................+300NC
Soldering Temperature (reflow).......................................+260NC
PACKAGE THERMAL CHARACTERISTICS (Note 1)
SO
Junction-to-Ambient Thermal Resistance (BJA)...........75NC/W
Junction-to-Case Thermal Resistance (BJC)................24NC/W
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a fourlayer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCCA – VGNDA = 3.0V to 5.5V, VCCB – VGNDB = 3.0V to 5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at
VCCA – VGNDA = 3.3V, VCCB – VGNDB = 3.3V, and TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNIT
DC CHARACTERISTICS
Supply Voltage
VCCA
Relative to GNDA
3.0
5.5
VCCB
Relative to GNDB
3.0
5.5
Unidirectional inputs
at DC or 2Mbps;
bidirectional inputs at DC
or switching at 2Mbps.
No load.
ICCA,
ICCB
Supply Current
All inputs switching at
max data rate. No load.
(Note 3)
VCCA = +5V,
VCCB = +5V
7.2
11
VCCA = +3.3V,
VCCB = +3.3V
6.2
9.5
VCCA
= +5V,
VCCB =
+5V
TA =
+25°C
15
22
TA =
+125°C
17
24
VCCA =
+3.3V,
VCCB =
+3.3V
TA =
+25°C
10
16
TA =
+125°C
11
18
V
mA
Undervoltage Lockout
Threshold
VUVLO
VCCA - VGNDA, VCCB - VGNDB (Note 4)
2
V
Undervoltage Lockout
Hysteresis
VUVLOHYS
VCCA - VGNDA, VCCB - VGNDB (Note 4)
0.1
V
����������������������������������������������������������������� Maxim Integrated Products 2
MAX14850
Six-Channel Digital Isolator
ELECTRICAL CHARACTERISTICS (continued)
(VCCA – VGNDA = 3.0V to 5.5V, VCCB – VGNDB = 3.0V to 5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at
VCCA – VGNDA = 3.3V, VCCB – VGNDB = 3.3V, and TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNIT
ISOLATION CHARACTERISTICS
Isolation Voltage
VISO
Working Isolation
Voltage
VIOWM
ESD Protection
t = 60s (Note 5)
600
VRMS
VGNDB - VGNDA continuous (Note 3), 50-year life
expectancy (Figure 4)
200
All pins
±2.5
VRMS
kV
LOGIC INPUTS AND OUTPUTS
Input Threshold Voltage
Input Logic-High Voltage
Input Logic-Low Voltage
VIT
VIH
VIL
I/OA1, I/OA2, relative to GNDA
0.5
0.7
INA1, INA2, relative to GNDA
0.7 x VCCA
INB1, INB2, relative to GNDB
I/OA1, I/OA2, relative to GNDA
0.7 x VCCB
0.7
I/OB1, I/OB2, relative to GNDB
0.7 x VCCB
Output Logic-High
Voltage
Output Logic-Low
Voltage
VOH
VOL
0.8
INB1, INB2, relative to GNDB
0.8
I/OA1, I/OA2, relative to GNDA
0.5
Input Capacitance
DVTOL
OUTA1, OUTA2, relative to GNDA,
source current = 4mA
VCCA - 0.4
OUTB1, OUTB2, relative to GNDB,
source current = 4mA
VCCB - 0.4
V
OUTA1, OUTA2, relative to GNDA,
sink current = 4mA
0.8
OUTB1, OUTB2, relative to GNDB,
sink current = 4mA
0.8
I/OA1, I/OA2, relative to GNDA,
sink current = 10mA
0.6
0.9
I/OA1, I/OA2, relative to GNDA,
sink current = 0.5mA
0.6
0.85
CIN
I/OA1, I/OA2 (Note 6)
INA1, INA2, INB1, INB2, f = 1MHz
V
0.3 x VCCB
I/OB1, I/OB2, relative to GNDB,
sink current = 30mA
Input/Output Logic-Low
Threshold Difference
V
INA1, INA2, relative to GNDA
I/OB1, I/OB2, relative to GNDB
V
V
0.4
50
mV
2
pF
1.5
kV/Fs
DYNAMIC SWITCHING CHARACTERISTICS
Common-Mode
Transient Immunity
dVISO/dt
VIN = VCC_ or VGND_ (Notes 3, 7)
����������������������������������������������������������������� Maxim Integrated Products 3
MAX14850
Six-Channel Digital Isolator
ELECTRICAL CHARACTERISTICS (continued)
(VCCA – VGNDA = 3.0V to 5.5V, VCCB – VGNDB = 3.0V to 5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at
VCCA – VGNDA = 3.3V, VCCB – VGNDB = 3.3V, and TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
Maximum Data Rate
(Note 3)
DRMAX
Minimum Pulse Width
PWMIN
Propagation Delay
(Note 3)
Pulse-Width Distortion
|tDPLH – tDPHL|
(Notes 3, 8)
tDPLH
tDPHL
PWD
CONDITIONS
MIN
INA1 to OUTB1, INA2 to OUTB2, INB1 to
OUTA1, INB2 to OUTA2
50
I/OA1 to I/OB1, I/OA2 to I/OB2, I/OB1 to I/OA1,
I/OB2 to I/OA2
2
INA1 to OUTB1, INA2 to OUTB2, INB1 to
OUTA1, INB2 to OUTA2 (Note 3)
20
TYP
MAX
UNIT
Mbps
ns
INA1 to OUTB1, INA2 to
OUTB2, INB1 to OUTA1,
INB2 to OUTA2, RL =
1MI, CL = 15pF, Figure 1
VCCA = VCCB =
+3.3V
20
30
VCCA = VCCB =
+5V
18
26
I/OA1 to I/OB1, I/OA2 to
I/OB2, R1 = 1.6kI, R2
= 180I, CL1 = CL2 =
15pF, Figure 2
VCCA = VCCB =
+3.3V
30
100
VCCA = VCCB =
+5V
30
100
I/OB1 to I/OA1, I/OB2
to I/OA2, R1 = 1kI, R2
= 120I, CL1 = CL2 =
15pF, Figure 2
VCCA = VCCB =
+3.3V
60
100
VCCA = VCCB =
+5V
60
100
INA1 TO OUTB1, INA2
TO OUTB2, INB1
TO OUTA1, INB2 TO
OUTA2, RL = 1MI,
CL = 15pF, Figure 1
VCCA = VCCB =
+3.3V
7
VCCA = VCCB =
+5V
7
I/OA1 to I/OB1, I/OA2 to
I/OB2, R1 = 1.6kI, R2
= 180I, CL1 = CL2 =
15pF, Figure 2
VCCA = VCCB =
+3.3V
12
VCCA = VCCB =
+5V
12
I/OB1 to I/OA1, I/OB2
to I/OA2, R1 = 1kI, R2
= 120I, CL1 = CL2 =
15pF, Figure 2
VCCA = VCCB =
+3.3V
60
VCCA = VCCB =
+5V
50
ns
ns
����������������������������������������������������������������� Maxim Integrated Products 4
MAX14850
Six-Channel Digital Isolator
ELECTRICAL CHARACTERISTICS (continued)
(VCCA – VGNDA = 3.0V to 5.5V, VCCB – VGNDB = 3.0V to 5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at
VCCA – VGNDA = 3.3V, VCCB – VGNDB = 3.3V, and TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
OUTB1 to OUTB2 output
skew, Figure 1
OUTA1 to OUTA2 output
skew, Figure 1
Channel-to-Channel
Skew (Notes 3, 8)
tDSKEWCC
I/OB1 to I/OB2 output
skew, Figure 2
I/OA1 to I/OA2 output
skew, Figure 2
Part-to-Part Skew
(Notes 3, 8)
tDSKEWPP
Rise Time (Note 3)
Fall Time (Note 3)
tR
tF
MIN
TYP
MAX
VCCA = VCCB =
+3.3V
3
VCCA = VCCB =
+5V
3
VCCA = VCCB =
+3.3V
3
VCCA = VCCB =
+5V
3
VCCA = VCCB =
+3.3V
6
VCCA = VCCB =
+5V
5
VCCA = VCCB =
+3.3V
20
VCCA = VCCB =
+5V
20
UNIT
ns
DtDPLH, DtDPHL
8
ns
OUTA1, OUTA2, OUTB1, OUTB2, 10% to 90%,
Figure 1
5
ns
OUTA1, OUTA2, OUTB1, OUTB2, 90% to 10%,
Figure 1
5
I/OA1, I/OA2, 90% to
10%, R1 = 1.6kI, R2
= 180I, CL1 = CL2 =
15pF, Figure 2
VCCA = VCCB =
+3.3V
30
60
VCCA = VCCB =
+5V
40
80
I/OB1, I/OB2, 90% to
10%, R1 = 1kI, R2 =
120I, CL1 = CL2 =
15pF, Figure 2
VCCA = VCCB =
+3.3V
3
6
VCCA = VCCB =
+5V
3
5
ns
����������������������������������������������������������������� Maxim Integrated Products 5
MAX14850
Six-Channel Digital Isolator
INSULATION AND SAFETY CHARACTERISTICS
PARAMETER
SYMBOL
CONDITIONS
VALUE
UNIT
4.2
mm
IEC INSULATION AND SAFETY RELATED FOR SPECIFICATIONS FOR SOIC-16
External Tracking
(Creepage)
CPG
IEC 60664-1
External Air Gap (Clearance)
CLR
IEC 60664-1
Minimum Internal Gap
Insulation thickness
Tracking Resistance
(Comparative Tracking
Index)
CTI
Insulation Resistance Across
Barrier
RISO
Capacitance Across
Isolation Barrier
CIO
IEC 112/VDE 030 Part 1
f = 1MHz
4.2
mm
0.0026
mm
175
V
1
GW
12
pF
1
kVPEAK
VDE IEC INSULATION CHARACTERISTICS
Surge Isolation Voltage
VIOSM
IEC 60747-17, section 5.3.1.6 and 5.4.6 for basic insulation
Repetitive Peak Isolation
Voltage
VIORM
IEC 60747-17, section 5.3.1.3
282
VPEAK
Rated Transient Isolation
Voltage
VIOTM
IEC 60747-17, section 5.3.1.4
850
VPEAK
Safety Limiting Temperature
TS
IEC 60747-17, section 7.2.1
+150
°C
Safety Limiting Side A Power
Dissipation
PSA
IEC 60747-17, section 7.2.1
0.75
W
Safety Limiting Side B Power
Dissipation
PSB
IEC 60747-17, section 7.2.1
0.75
W
Apparent Charge Method
qpd
IEC 60747-17, section 7.4, method a and b
5
pC
Overvoltage Category
IEC 60664-1, single- or three-phase 50V DC or AC
I, II
—
Overvoltage Category
IEC 60664-1, single- or three-phase 100V DC or AC
I
—
40/125/21
—
2
—
Climatic Category
Pollution Degree
DIN VDE 0110, Table 1
Note 2: All units are production tested at TA = +25°C. Specifications over temperature are guaranteed by design. All voltages of
side A are referenced to GNDA. All voltages of side B are referenced to GNDB, unless otherwise noted.
Note 3: Guaranteed by design. Not production tested.
Note 4: The undervoltage lockout threshold and hysteresis guarantee that the outputs are in a known state during a slump in the
supplies. See the Detailed Description section for more information.
Note 5: The isolation is guaranteed for t = 60s, and tested at 120% of the guaranteed value for 1s.
Note 6: DVTOL = VOL – VIL. This is the minimum difference between the output logic-low voltage and the input logic threshold for
the same I/O pin. This ensures that the I/O channels are not latched low when any of the I/O inputs are driven low (see the
Bidirectional Channels section).
Note 7: The common-mode transient immunity guarantees that the device will hold its outputs stable when the isolation voltage
changes at the specified rate.
Note 8: Pulse-width distortion is defined as the difference in propagation delay between low-to-high and high-to-low transitions
on the same channel. Channel-to-channel skew is defined as the difference in propagation delay between different channels on the same device. Part-to-part skew is defined as the difference in propagation delays (for unidirectional channels)
between different devices, when both devices operate with the same supply voltage, at the same temperature and have
identical package and test circuits.
����������������������������������������������������������������� Maxim Integrated Products 6
MAX14850
Six-Channel Digital Isolator
Test Circuits/Timing Diagrams
VCCA
INA1, INA2
50%
GNDA
VCCA
0.1µF
VCCA
0.1µF
VCCB
50%
tDPLH
VCCB
tDPHL
VCCB
OUTB1
MAX14850
50Ω
INA_
TEST
SOURCE
OUTB_
GNDA
50%
50%
GNDB
GNDB
RL
CL
tDSKEWCC
VCCB
90%
50%
OUTB2
(A)
10%
GNDB
tR
tF
(B)
Figure 1. Test Circuit (A) and Timing Diagram (B) for Unidirectional Channels
VCCA
R1
0.1µF
I/OA_
CL1
0.1µF
VCCB
VCCA
MAX14850
GNDA
R2
VCCB
I/OB_
CL2
GNDB
TEST
SOURCE
(A)
VCCA
I/OA1, I/OA2
VCCB
50%
GNDA
I/OB1, I/OB2
50%
GNDB
tDPLH
tDPHL
VCCB
50%
I/OB1
VOL(min)
50%
tDPHL
VOL(min)
90%
I/OA2
tF
10%
50%
tDSKEWCC
VCCA
50%
VOL(min)
tDPLH
50%
I/OA1
90%
I/OB2
50%
VCCA
tDSKEWCC
VCCB
50%
50%
VOL(min)
(B)
tF
10%
(C)
Figure 2. Test Circuit (A) and Timing Diagrams (B) and (C) for Bidirectional Channels
����������������������������������������������������������������� Maxim Integrated Products 7
MAX14850
Six-Channel Digital Isolator
Typical Operating Characteristics
(VCCA – VGNDA = 3.3V, VCCB – VGNDB = 3.3V, all inputs idle, TA = +25NC, unless otherwise noted.
ICCB vs. DATA RATE
7
5
5
4
INB1/INB2
SWITCHING
5
4
INA1/INA2
SWITCHING
3
2
2
1
1
0
0.001
0
0.001
0.1
1
10
100
0.01
9
TA = -40°C
8
10
100
2
1
PULLUP = 2k
TA = +125°C
9
0.1
1
5
TA = +25°C
4
2
1
1
0
3.0
3.5
4.0
4.5
5.0
5.5
3.0
3.5
VCCA (V)
OUTA_ VOH vs. SOURCE CURRENT
6
5
ICCB
VCCA = 5V
4
5.0
5
4
5.5
2
3
2
VCCA = 3.3V
3
2
4.5
OUTA_ VOL vs. SINK CURRENT
VCCA = 3.3V
3
4.0
VCCB (V)
5
OUTA_ VOH (V)
7
TA = -40°C
TA = -40°C
4
3
0
MAX14850 toc07
ICCA
5
2
ICC vs.TEMPERATURE
8
6
3
DATA RATE (Mbps)
9
10
7
6
10
1
TA = +125°C
8
OUTA_ VOL (V)
0.01
0.1
ICCB vs. VCCB
ICCB (mA)
I/OA1/I/OA2
SWITCHING
3
0
0.001
0.01
10
MAX14850 toc08
4
PULLUP = 2k
DATA RATE (Mbps)
7
ICCA (mA)
ICCB (mA)
6
ICC (mA)
1
10
MAX14850 toc04
7
4
0.1
0
0.001
ICCA vs. VCCA
ICCB vs. DATA RATE
I/OB1/I/OB2
SWITCHING
3
DATA RATE (Mbps)
8
I/OB1/I/OB2
SWITCHING
1
DATA RATE (Mbps)
5
4
MAX14850 toc09
0.01
I/OA1/I/OA2
SWITCHING
2
MAX14850 toc05
3
ICCA (mA)
6
ICCB (mA)
ICCA (mA)
6
6
MAX14850 toc06
7
INB1/INB2
SWITCHING
8
7
MAX14850 toc02
MAX14850 toc01
INA1/INA2
SWITCHING
8
ICCA vs. DATA RATE
9
MAX14850 toc03
ICCA vs. DATA RATE
9
1
1
VCCA = 5V
1
0
0
-40 -25 -10 5 20 35 50 65 80 95 110 125
TEMPERATURE (°C)
0
0
15
30
45
ISOURCE (mA)
60
75
0
15
30
45
60
75
ISINK (mA)
����������������������������������������������������������������� Maxim Integrated Products 8
MAX14850
Six-Channel Digital Isolator
Typical Operating Characteristics (continued)
(VCCA – VGNDA = 3.3V, VCCB – VGNDB = 3.3V, all inputs idle, TA = +25NC, unless otherwise noted.
VCCB = 3.3V
2
1
3
VCCB = 3.3V
2
14
PROPAGATION DELAY (ns)
4
OUTB_ VOL (V)
4
16
MAX14850 toc11
VCCB = 5V
OUTB_ VOH (V)
5
MAX14850 toc10
5
3
PROPAGATION DELAY
vs. SUPPLY VOLTAGE
OUTB_ VOL vs. SINK CURRENT
1
VCCB = 5V
VGNDB - VGNDA = 0V
VGNDB - VGNDA = -100V
12
10
8
VGNDB - VGNDA = +100V
6
4
VDDA = VDDB
INA_ TO OUTB_
LOW TO HIGH TRANSITION
2
0
0
15
30
45
60
75
3.0
3.5
4.0
4.5
5.0
6
4
VDDA = VDDB
INA_ TO OUTB_
HIGH TO LOW TRANSITION
0
3.5
4.0
4.5
5.0
12
HIGH TO LOW
10
8
6
4
2
5.5
0
20
40
60
80
LOW TO HIGH
16
14
12
HIGH TO LOW
10
8
6
4
2
INA_ TO OUTB_
0
MAX14850 toc15
MAX14850 toc14
LOW TO HIGH
14
INA_ TO OUTB_
0
-40 -25 -10 5 20 35 50 65 80 95 110 125
100
CL (pF)
TA (°C)
PROPAGATION DELAY
vs. SUPPLY VOLTAGE
PROPAGATION DELAY
vs. SUPPLY VOLTAGE
PROPAGATION DELAY
vs. CAPACITIVE LOAD
VGNDB - VGNDA = -100V
VGNDB - VGNDA = +100V
6
4
VDDA = VDDB
INB_ TO OUTA_
LOW TO HIGH TRANSITION
2
0
3.5
4.0
4.5
VDDA (V)
5.0
5.5
VGNDB - VGNDA = -100V
10
8
VGNDB - VGNDA = +100V
6
4
VDDA = VDDB
INB_ TO OUTA_
HIGH TO LOW TRANSITION
2
0
3.0
3.5
4.0
4.5
VDDA (V)
5.0
5.5
20
MAX14850 toc18
12
VGNDB - VGNDA = 0V
18
PROPAGATION DELAY (ns)
MAX1960 toc16
VGNDB - VGNDA = 0V
10
12
MAX14850 toc17
VDDA (V)
16
5.5
18
PROPAGATION DELAY (ns)
VGNDB - VGNDA = +100V
16
PROPAGATION DELAY (ns)
8
18
PROPAGATION DELAY (ns)
PROPAGATION DELAY (ns)
0
75
PROPAGATION DELAY
vs. TEMPERATURE
2
PROPAGATION DELAY (ns)
60
PROPAGATION DELAY
vs.CAPACITIVE LOAD
VGNDB - VGNDA = -100V
3.0
45
PROPAGATION DELAY
vs. SUPPLY VOLTAGE
10
14
30
VDDA (V)
VGNDB - VGNDA = 0V
3.0
15
ISINK (mA)
12
8
0
ISOURCE (mA)
MAX14850 toc13
0
MAX1960 toc12
OUTB_ VOH vs. SOURCE CURRENT
LOW TO HIGH
16
14
12
HIGH TO LOW
10
8
6
4
2
INB_ TO OUTA_
0
0
20
40
60
80
100
CL (pF)
����������������������������������������������������������������� Maxim Integrated Products 9
MAX14850
Six-Channel Digital Isolator
Typical Operating Characteristics (continued)
(VCCA – VGNDA = 3.3V, VCCB – VGNDB = 3.3V, all inputs idle, TA = +25NC, unless otherwise noted.
12
HIGH TO LOW
8
6
4
25
20
15
10
VDDA = VDDB
I/OA_ TO I/OB_
LOW TO HIGH TRANSITION
PULLUP = 1kI
5
2
INB_ TO OUTA_
0
VGNDB - VGNDA = -100V
VGNDB - VGNDA = 0V
0
-40 -25 -10 5 20 35 50 65 80 95 110 125
3.0
TA (°C)
3.5
4.0
4.5
5.0
5
30
20
HIGH TO LOW
3.5
3.0
4.0
4.5
VGNDB - VGNDA = +100V
25
20
VGNDB - VGNDA = 0V
VGNDB - VGNDA = -100V
10
VDDA = VDDB
I/OB_ TO I/OA_
LOW TO HIGH TRANSITION
PULLUP = 1kI
0
3.0
-40 -25 -10 5 20 35 50 65 80 95 110 125
3.5
4.0
4.5
5.0
VDDA (V)
PROPAGATION DELAY
vs. SUPPLY VOLTAGE
PROPAGATION DELAY
vs. TEMPERATURE
50
VGNDB - VGNDA = -100V
VGNDB - VGNDA = 0V
30
20
VDDA = VDDB
I/OB_ TO I/OA_
HIGH TO LOW TRANSITION
0
3.5
4.0
4.5
VDDA (V)
5.0
5.5
5.5
60
MAX14850 toc25
VGNDB - VGNDA = +100V
50
PROPAGATION DELAY (ns)
MAX14850 toc24
TA (°C)
10
5.5
15
5
I/OA_ TO I/OB_
PULLUP = 1kI
60
5.0
30
10
0
MAX14850 toc21
VDDA = VDDB
I/OA_ TO I/OB_
HIGH TO LOW TRANSITION
VDDA (V)
PROPAGATION DELAY (ns)
MAX14850 toc22
PROPAGATION DELAY (ns)
10
PROPAGATION DELAY
vs. SUPPLY VOLTAGE
LOW TO HIGH
3.0
VGNDB - VGNDA = 0V V
GNDB - VGNDA = -100V
VDDA (V)
50
40
15
0
5.5
PROPAGATION DELAY
vs.TEMPERATURE
40
VGNDB - VGNDA = +100V
MAX14850 toc23
10
20
PROPAGATION DELAY (ns)
14
VGNDB - VGNDA = +100V
30
PROPAGATION DELAY (ns)
LOW TO HIGH
PROPAGATION DELAY (ns)
PROPAGATION DELAY (ns)
35
MAX14850 toc19
18
16
PROPAGATION DELAY
vs. SUPPLY VOLTAGE
PROPAGATION DELAY
vs. SUPPLY VOLTAGE
MAX14850 toc20
PROPAGATION DELAY
vs. TEMPERATURE
40
HIGH TO LOW
30
20
LOW TO HIGH
10
I/OB_ TO I/OA_
PULLUP = 1kI
0
-40 -25 -10 5 20 35 50 65 80 95 110 125
TA (°C)
���������������������������������������������������������������� Maxim Integrated Products 10
MAX14850
Six-Channel Digital Isolator
Pin Configuration
TOP VIEW
+
16 VCCB
VCCA
1
INA1
2
INA2
3
OUTA1
4
OUTA2
5
12 INB2
I/OA1
6
11 I/OB1
I/OA2
7
10 I/OB2
GNDA
8
9
15 OUTB1
MAX14850
14 OUTB2
13 INB1
GNDB
SO
Pin Description
PIN
NAME
FUNCTION
VOLTAGE RELATIVE TO
1
VCCA
Supply Voltage of Logic Side A. Bypass VCCA with a 0.1FF ceramic
capacitor to GNDA.
GNDA
2
INA1
Logic Input 1 on Side A. INA1 is translated to OUTB1.
GNDA
3
INA2
Logic Input 2 on Side A. INA2 is translated to OUTB2.
GNDA
4
OUTA1
Logic Output 1 on Side A. OUTA1 is a push-pull output.
GNDA
5
OUTA2
Logic Output 2 on Side A. OUTA2 is a push-pull output.
GNDA
GNDA
GNDA
6
I/OA1
Bidirectional Input/Output 1 on Side A. I/OA1 is translated to/from I/OB1
and is a open-drain output.
7
I/OA2
Bidirectional Input/Output 2 on Side A. I/OA2 is translated to/from I/OB2
and is a open-drain output.
8
GNDA
Ground Reference for Side A
—
9
GNDB
Ground Reference for Side B
—
���������������������������������������������������������������� Maxim Integrated Products 11
MAX14850
Six-Channel Digital Isolator
Ground Isolation/Level Shifting
The MAX14850 tolerates a ground difference of 600VRMS.
Therefore, VGNDA can be 850VDC higher or lower than
VGNDB. In addition, the device translates logic levels
when (VCCA–VGNDA) is higher or lower voltage than
(VCCB–VGNDB), as long as each is within the valid 3.0V
to 5.5V range.
The I/OA1, I/OA2, I/OB1, and I/OB2 pins have open-drain
outputs, requiring pullup resistors to their respective supplies for logic-high outputs. The output low voltages are
guaranteed for sink currents of up to 30mA for side B, and
10mA for side A (see the Electrical Characteristics table).
The bidirectional channels of the device support I2C
clock stretching.
Unidirectional and Bidirectional Channels
The MAX14850 operates both as a unidirectional device
and bidirectional device simultaneously. Each unidirectional channel can only be used in the direction shown in
the functional diagram. The bidirectional channels function without requiring a direction control input.
Unidirectional Channels
The device features four unidirectional channels that
operate independently with guaranteed data rates from
DC to 50Mbps. The output driver of each unidirectional
channel is push-pull, eliminating the need for pullup
resistors. The outputs are able to drive both TTL and
CMOS logic inputs.
Bidirectional Channels
The device features two bidirectional channels that have
open-drain outputs. The bidirectional channels do not
require a direction control input. A logic-low on one side
causes the corresponding pin on the other side to be
pulled low while avoiding data latching within the device.
The input logic-low threshold (VIT) of I/OA1 and I/OA2 are
at least 50mV lower than the output logic-low voltages of I/
OA1 and I/OA2. This prevents an output logic-low on side
A from being accepted as an input low and subsequently
transmitted to side B, thus preventing a latching action.
Startup and Undervoltage Lockout
The VCCA and VCCB supplies are both internally monitored for undervoltage conditions. Undervoltage events
can occur during power-up, power-down, or during
normal operation due to a slump in the supplies. When an
undervoltage event is detected on either of the supplies, all
outputs on both sides are automatically controlled, regardless of the status of the inputs. The bidirectional outputs
become high impedance and are pulled high by the external pullup resistor on the open-drain output. The unidirectional outputs are pulled high internally to the voltage of the
VCCA or VCCB supply during undervoltage conditions.
When an undervoltage condition is detected on either
supply, all unidirectional outputs are pulled to the supplies
(Table 1). The bidirectional outputs are high impedance
and pulled to the supplies by the external pullup resistors.
Safety Regulatory Approvals
The MAX14850 is safety certified by UL, CSA, and
IEC 60747-5-2. Per UL1577, the MAX14850 is 100%
tested at an equivalent VISO of 720VRMS for one second
(see Table 2).
Figure 3 shows the behavior of the outputs during powerup and power-down.
Table 1. Output Behavior During Undervoltage Conditions
VIN
VCCA
VCCB
VOUTA_
VOUTB_
1
Powered
Powered
1
1
0
Powered
Powered
0
0
X
Under Voltage
Powered
Follows VCCA
1
X
Powered
Under Voltage
1
Follows VCCB
Table 2. Safety Regulatory Approvals (Pending)
SAFETY AGENCY
STANDARD
ISOLATION NUMBER
FILE NUMBER
UL
UL1577 Recognized
600VRMS isolation voltage for 60 seconds
Pending
VDE
Approved to 60747-17
Basic insulation, 600VRMS for 60 seconds
Pending
���������������������������������������������������������������� Maxim Integrated Products 13
MAX14850
Six-Channel Digital Isolator
LIFE EXPECTANCY
vs. WORKING ISOLATION VOLTAGE
1000
VCCB
5V/div
VOUTA_
VOUTB_
VI/OA_
VI/OB_
400µs/div
WORKING LIFE - YEARS (LOG SCALE)
VCCA
100
50
VIOWM = 200VRMS
10
1
0.1
0.001
0
100 200 300 400 500 600 700 800
WORKING ISOLATION VOLTAGE (VIOWM) - VRMS
Figure 3. Undervoltage Lockout Behavior
Applications Information
Affect of Continuous Isolation
on Lifetime
High-voltage conditions cause insulation to degrade
over time. Higher voltages result in faster degradation.
Even the high-quality insulating material used in the
MAX14850 can degrade over long periods of time with a
constant high-voltage across the isolation barrier. Figure 4
shows the life expectancy of the MAX14850 vs. working
isolation voltage.
Figure 4. Life Expectancy vs. Working Isolation Voltage
Power-Supply Sequencing
The MAX14850 does not require special power-supply
sequencing. The logic levels are set independently on
either side by VCCA and VCCB. Each supply can be present over the entire specified range regardless of the level
or presence of the other.
Power-Supply Decoupling
To reduce ripple and the chance of introducing data
errors, bypass VCCA and VCCB with 0.1FF ceramic
capacitors to GNDA and GNDB, respectively. Place the
bypass capacitors as close to the power-supply input
pins as possible.
���������������������������������������������������������������� Maxim Integrated Products 14
MAX14850
Six-Channel Digital Isolator
Typical Operating Circuits (continued)
0.1µF
3.3V
0.1µF
VCCA
RPUA
µC
5V
VCCB
RPUA
RPUB
MAX14850
RPUB
SDA
I/OA1
I/OB1
SDA
SCL
I/OA2
I/OB2
SCL
INA1
OUTB1
INA2
OUTB2
GPIO1
GPIO2
GPIO3
VCCB MONITOR
SPARE
OUTA1
INB1
OUTA2
INB2
GNDA
RESET
LOAD DAC
RST
DAC
LDAC
GNDB
600VRMS
ISOLATION
���������������������������������������������������������������� Maxim Integrated Products 15
MAX14850
Six-Channel Digital Isolator
Typical Operating Circuits (continued)
0.1µF
3.3V
0.1µF
VCCA
5V
VCCB
RPUB
RPUA
GPIO1
RTS
GPIO3
VCCB MONITOR
RO
INB1
OUTA1
µC
RE
I/OB1
I/OA1
RX
TX
MAX14850
I/OA2
I/OB2
INA1
OUTB1
INA2
OUTB2
DE
MAX13085E
A
B
DI
INB2
OUTA2
GNDA
GNDB
600VRMS
ISOLATION
Ordering Information
PART
MAX14850ASE+
TEMP RANGE
-40NC to +125NC
PIN-PACKAGE
Chip Information
PROCESS: BiCMOS
16 SO
Package Information
+Denotes a lead(Pb)-free/RoHS-compliant package.
For the latest package outline information and land patterns
(footprints), go to www.maxim-ic.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
16 SO
S16+3
OUTLINE
NO.
LAND
PATTERN NO.
21-0041
90-0097
���������������������������������������������������������������� Maxim Integrated Products 16
MAX14850
Six-Channel Digital Isolator
Revision History
REVISION
NUMBER
REVISION
DATE
0
3/12
DESCRIPTION
Initial release
PAGES
CHANGED
—
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical
Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
©
2012 Maxim Integrated Products
17
Maxim is a registered trademark of Maxim Integrated Products, Inc.