A23L3616/A23L36161 Series Preliminary 8M X 16 / 16M X 8 BIT CMOS MASK ROM Document Title 8M X 16 / 16M X 8 BIT CMOS MASK ROM Revision History History Issue Date Remark 0.0 Initial issue November 3, 2003 Preliminary 0.1 Add A23L36161 (flash type) August 27, 2004 0.2 Modify A23L36161V pin configuration: November 24, 2004 Rev. No. pin 1 from A22 to A16 pin 48 from A16 to A22 PRELIMINARY (November, 2004, Version 0.2) AMIC Technology, Corp. A23L3616/A23L36161 Series Preliminary 8M X 16 / 16M X 8 BIT CMOS MASK ROM Features Full static operation All inputs and outputs are directly TTL-compatible Available in 44-pin SOP, 48-pin TSOP (forward, reverse type and flash memory’s pinouts compatible) packages Pinout compatible with flash type (A23L36161) 8M x 16 bit or 16M x 8 bit organization Supply voltage range: 2.7V~3.6V Access time: 100ns (max.)/3.0V~3.6V 120ns (max.)/2.7V~3.6V Current: Operating: 40mA (typ.)/3.3V Standby: 10µA (typ.)/3.3V Three-state outputs for wired-OR expansion Pin Configurations SOP TSOP (forward type) 42 41 A8 A7 3 4 A6 5 A5 A4 A3 6 7 A2 9 A1 1 A18 A17 8 A0 10 11 CE GND 12 13 OE 14 15 O0 O8 A23L3616M(For 8M X 16 only) A20 2 44 43 A21 40 39 38 37 36 35 34 33 A19 A9 A10 A11 A12 A13 A14 A15 A16 32 A22 GND 31 O15 30 29 O7 O14 28 O6 27 O13 26 O5 O12 O1 16 17 O9 18 O2 19 O10 20 25 O3 21 24 O4 O11 22 23 VCC BYTE A16 A15 A14 A13 A12 A11 A10 A9 A8 A19 A21 A20 A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE A23L3616V 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 GND GND O15/A-1 O7 O14 O6 O13 O5 O12 O4 VCC VCC A22 O11 O3 O10 O2 O9 O1 O8 O0 OE GND GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 BYTE A16 A15 A14 A13 A12 A11 A10 A9 A8 A19 A21 A20 A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE TSOP (reverse type) GND GND O15/A-1 O7 O14 O6 O13 O5 O12 O4 VCC VCC A22 O11 O3 O10 O2 O9 O1 O8 O0 OE GND GND PRELIMINARY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 (November, 2004, Version 0.2) 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A23L3616R 1 AMIC Technology, Corp. A23L3616/A23L36161 Series Pin Configurations (continued) TSOP (forward type) A16 A15 A14 A13 A12 A11 A10 A9 A8 A19 NC NC A20 NC A21 A18 A17 A7 A6 A5 A4 A3 A2 A1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A23L36161V A22 BYTE GND O15/A-1 O7 O14 O6 O13 O5 O12 O4 VCC O11 O3 O10 O2 O9 O1 O8 O0 OE GND CE A0 Block Diagram ROW MEMORY CELL DECODER ARRAY DRIVER (A-1) A0 - A22 ADDRESS INPUTS COLUMN DECODER COLUMN SELECTOR CIRCUITRY DRIVER O0 CE OE BYTE O1 POWER-DOWN DOWN OR OUTPUT ENABLE CIRCUITRY BYTE CIRCUITRY O2 O3 O4 O5 O6 O7 (O8) (O9) (O10) (O11) (O12) (O13) (O14) (O15) PRELIMINARY (November, 2004, Version 0.2) 2 AMIC Technology, Corp. A23L3616/A23L36161 Series Pin Descriptions Pin No. 44L SOP (A23L3616) (16M X 8 only) 48L TSOP (A23L3616) 48L TSOP (A23L36161) Symbol 1-11, 33-44 2-23, 36 1-10, 13, 15-25, 48 A0-A22 Address Inputs 15-22, 24-30 28-35, 39-45 29-36, 38-44 O0-O14 Data Outputs 31 46 45 O15/A-1 Output 15(WORD mode) /LSB Address (BYTE mode) 12 24 26 CE Chip Enable Input 14 27 28 OE Output Enable Input No 1 47 BYTE BYTE or WORD mode Selection 23 37-38 37 VCC Power Supply 13, 32 25-26, 47-48 27, 46 GND Ground 11-12, 14 NC Description No Connection Recommended DC Operating Conditions (TA = 0°C to + 70°C) Symbol Parameter VCC Supply Voltage GND Ground Min. Max. Unit 2.7 3.6 V 0 0 V VIH Input High Voltage 2.2 VCC+0.3 V VIL Input Low Voltage - 0.3 0.6 V PRELIMINARY (November, 2004, Version 0.2) 3 AMIC Technology, Corp. A23L3616/A23L36161 Series Absolute Maximum Ratings* *Comments Ambient Operating Temperature . . . . . . . . 0°C to + 70°C Storage Temperature . . . . . . . . . . . . . . -65°C to + 125°C Output Voltage . . . . . . . . . . . . . . . . . -0.5V to VCC + 0.5V Input Voltage . . . . . . . . . . . . . . . . . . -0.5V to VCC + 0.5V Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to this device. These are stress ratings only. Functional operation of this device at these or any other conditions above those indicated in the operational sections of this specification is not implied or intended. Exposure to the absolute maximum rating conditions for extended periods may affect device reliability. DC Electrical Characteristics (TA = 0°C to + 70°C, VCC = 2.7V~3.6V, GND = 0V for -100, VCC = 3.0V~3.6V, GND = 0 for -70) Symbol Parameter VOH Output High Voltage VOL Output Low Voltage VlH Input High Voltage VlL Input Low Voltage ⎢lLI⎥ Min. Max. Conditions V IOH = -0.4mA (3V) 0.4 V IOL = 1.6mA (3V) 2.2 VCC + 0.3 V -0.3 0.6 V Input Leakage Current +10 µA VCC = max. VIN = VCC to GND ⎢lLO⎥ Output Leakage Current +10 µA VCC = max. VOUT = VCC to GND ICC Operating Supply Current 60 mA tCYC = min. ISB Standby Supply Current (TTL) 1.5 mA CE = VIH ISB1 Standby Supply Current (CMOS) 30 µA CE ≥ VCC - 0.2V PRELIMINARY (November, 2004, Version 0.2) 2.4 Unit 4 Note 1 2 AMIC Technology, Corp. A23L3616/A23L36161 Series Capacitance Symbol Parameter Min. Max. Unit CI Input Capacitance 10 pF CO Output Capacitance 10 pF AC Characteristics Test Conditions Note TA = 25°C f = 1.0MHz 3 (TA = 0°C to +70°C, VCC = 2.7V~3.6V for -120, VCC = 3.0V~3.6V for -100, GND = 0V) Symbol Parameter A23L3616/ A23L36161 -100 A23L3616/ A23L36161 -120 Min. Min. Max. 100 Unit Note Max. tCYC Cycle Time 120 tAA Address Access Time 100 120 ns tACE Chip Enable Access Time 100 120 ns tAOE Output Enable Access Time 30 50 ns tOH Output Hold after Address Change 0 0 ns tLZ Output Low Z Delay 0 0 ns 4, 6 tHZ Output High Z Delay* ns 5, 6 20 ns 20 * tHZ is specified from either OE or CE going disabled, whichever occurs first. Notes: 1. OE / CE = VIH (Output is unloaded) 2. VIN = VIH/VIL, OE / CE = VIL (Output is unloaded) 3. This parameter is periodically sampled and is not 100% tested. All pins, except pins under test, are tied to AC ground. 4. Output LOW impedance delay (tLZ) is measured from CE or OE going active. 5. Output HIGH impedance delay (tHZ) is measured from CE or OE going inactive. 6. This parameter is sampled and not 100% tested. PRELIMINARY (November, 2004, Version 0.2) 5 AMIC Technology, Corp. A23L3616/A23L36161 Series Timing Waveforms Propagation Delay from Address ( CE = Active, OE = Active) tCYC ADDRESS INPUTS VALID tAA tOH VALID DATA OUT Propagation Delay from Chip Enable or Output Enable (Address Valid) CHIP ENABLE VALID tACE OUTPUT ENABLE VALID tLZ tAOE tHZ VALID DATA OUT AC Test Conditions Part No. A23L3616/ A23L36161 –100 Applied Voltage Input Pulse Levels Input Rise and Fall Time Timing Measurement Reference Level Output Load PRELIMINARY (November, 2004, Version 0.2) A23L3616/ A23L36161 -120 3.0V~3.6V 2.7V~3.6V 0.4V to 2.4V 0.4V to 2.4V 10 ns 10 ns VIN = 1.4V, VOUT = 1.4V VIN = 1.4V, VOUT = 1.4V 1 TTL gate and CL = 100pF 1 TTL gate and CL = 100pF 6 AMIC Technology, Corp. A23L3616/A23L36161 Series Function Table CE OE /NC BYTE O15/A-1 O0 - O7 O8 - O15 Mode L L H Data Pin O15 Data Out Data out Word L L L LSB Address A-1 Data Out Hi - Z Byte H X X X Hi - Z Hi - Z Power-down L H X X Hi - Z Hi - Z Output Disable Ordering Information Part No. Access Time (ns) Package A23L3616M-100 (16M X 8 only) 100 44L SOP A23L3616M-120 (16M X 8 only) 120 44L SOP A23L3616V-100 100 48L TSOP (Forward) A23L3616V-120 120 48L TSOP (Forward) A23L3616R-100 100 48L TSOP (Reverse) A23L3616R-120 120 48L TSOP (Reverse) A23L36161V-100 100 48L TSOP (Flash Compatible) A23L36161V-120 120 48L TSOP (Flash Compatible) PRELIMINARY (November, 2004, Version 0.2) 7 AMIC Technology, Corp. A23L3616/A23L36161 Series Package Information unit: inches/mm SOP 44L Outline Dimensions 23 E Gauge Plane HE 44 θ L 0.010" 1 b 22 Detail F y e A L1 A1 S D A2 C D Seating Plane See Detail F Symbol A Dimensions in inches Dimensions in mm Min Nom Max Min Nom Max - - 0.118 - - 3.00 A1 0.004 - - 0.10 - - A2 0.103 0.106 0.109 2.62 2.69 2.77 b 0.013 0.016 0.020 0.33 0.40 0.50 C 0.007 0.008 0.010 0.18 0.20 0.25 D - 1.122 1.130 - 28.50 28.70 E e 0.490 - 0.496 0.050 0.500 - 12.45 - 12.60 1.27 12.70 - HE 0.620 0.631 0.643 15.75 16.03 16.33 L 0.024 0.032 0.040 0.61 0.80 1.02 L1 - 0.0675 - - 1.71 - S - - 0.045 - - 1.14 y - - 0.004 - - 0.10 θ 0° - 8° 0° - 8° Notes: 1. The maximum value of dimension D includes end flash. 2. Dimension E does not include resin fins. 3. Dimension S includes end flash. PRELIMINARY (November, 2004, Version 0.2) 8 AMIC Technology, Corp. A23L3616/A23L36161 Series Package Information unit: inches/mm TSOP 48L (Type I) Outline Dimensions 1 48 24 25 y D1 A1 A2 A D 0.25 c S e E b D Detail "A" L θ Detail "A" Dimensions in inches Dimensions in mm Symbol Min Nom Max Min Nom Max A - - 0.047 - - 1.20 A1 0.002 - 0.006 0.05 - 0.15 A2 0.037 0.039 0.042 0.94 1.00 1.06 b 0.007 0.009 0.011 0.18 0.22 0.27 c 0.004 - 0.008 0.12 - 0.20 D 0.779 0.787 0.795 19.80 20.00 20.20 D1 0.720 0.724 0.728 18.30 18.40 18.50 E - 0.472 0.476 - 12.00 12.10 e L 0.020 BASIC 0.016 S 0.020 0.50 BASIC 0.024 0.40 0.011 Typ. 0.50 0.60 0.28 Typ. y - - 0.004 - - 0.10 θ 0° - 8° 0° - 8° Notes: 1. The maximum value of dimension D includes end flash. 2. Dimension E does not include resin fins. 3. Dimension S includes end flash. PRELIMINARY (November, 2004, Version 0.2) 9 AMIC Technology, Corp.