POS Adj Volta ge oltag PRELIMINARY SPECIFICATION Re gula tor gulator Austin Semiconductor, Inc. Positive Adjustable Voltage Regulator 16 Pin CerPack Gullwing(GW16) • SMD 5962-99517 pending • Radiation Tolerant • MIL-STD-883, 1.2.1 “QML” pending FEATURES • Guaranteed 0.5A Output Current • Radiation Guaranteed to 100K RADS TID • Adjustable output down to 1.2V • Current Limit constant over temperature • Output is short circuit protected • 80Db Ripple Rejection • Packages 16 pin Cerpack Gullwing 3 Lead Metal Can • Process / Temperature Ranges MILITARY (-55oC to +125oC) MIL-STD-883 paragraph 1.2.1 MIL-STD-883 CLASS ‘S’ N/C 1 16 N/C N/C 2 15 N/C ADJ 3 14 N/C N/C 4 13 OUTPUT/ SENSE INPUT 5 12 OUTPUT N/C 6 11 N/C N/C 7 10 N/C N/C 8 9 N/C MARKINGS GW16 TO39 3 Lead Metal Can (TO39) (Bottom View) /XT /883 /SPACE 1 OUTPUT GENERAL DESCRIPTION The AS117 is an adjustable 3-terminal positive voltage regulator capable of supplying in excess of .5A over a 1.2V to 37V output voltage range. It is exceptionally easy to use & requires only 2 external resistors to set the output voltage. Further, both line and load regulation are better than standard fixed regulators. In addition to higher performance than fixed regulators, the AS117 offers full overload protection. Included on the chip are current limit, thermal overload protection and safe area protection. All overload protection circuitry remains fully functional even if the adjustment terminal is disconnected. The AS117 is radiation tolerant to 100K Rads(Si) total dose levels as tested by MIL-STD-883 Method 1019 Condition A. The user is encouraged to contact ASI for acopy of current radiation testing reports. AS117 RAD-TOL Rev. 1.1 06/05 PIN ASSIGNMENT (Top View) AVAILABLE AS MILITARY / SPACE SPECIFICATIONS OPTIONS AS117 RAD-TOL 3 2 INPUT ADJUSTMENT For more products and information please visit our web site at www.austinsemiconductor.com Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 1 POS Adj Volta ge oltag PRELIMINARY SPECIFICATION Re gula tor gulator Austin Semiconductor, Inc. AS117 RAD-TOL TYPICAL APPLICATIONS Besides replacing fixed regulators, the AS117 is useful in a wide variety of other applications. Since the regulator is “Floating” and sees only the input-to-output differential voltage, supplies of several hundred volts can be regulated as long as the maximum input to output differential is not exceeded, (i.e., avoid short circuiting the output). Also it makes an especially simple adjustable switching regulator, a programmable output regulator, or by connecting a fixed resistor between the adjustment pin & the output pin, the AS117 can be used as a precision current regulator. Supplies with electronic shutdown can be achieved by clamping the adjustment terminal to ground which programs the output to 1.2V where most loads draw little current. Normally no capacitors are needed unless the device is situated more than 6 inches from the input filter capacitors in which case an input bypass is needed. An optional output capacitor can be added to improve transient response. The adjustment terminal can be bypassed to achieve very high ripple rejection ratios which are difficult to achieve with standard 3-terminal regulators. AS117 RAD-TOL Rev. 1.1 06/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 2 POS Adj Volta ge oltag PRELIMINARY SPECIFICATION Re gula tor gulator Austin Semiconductor, Inc. AS117 RAD-TOL TYPICAL APPLICATIONS (CONTINUED)3 Typical Applications (Continued) High Current Adjustable Regulator 0 ‡ Optional — improves ripple rejection †Solid tantalum *Minimum load current = 30 mA Power Follower 0 to 30V Regulator 0 Full output current not available at high input-output voltages AS117 RAD-TOL Rev. 1.1 06/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 3 POS Adj Volta ge oltag PRELIMINARY SPECIFICATION Re gula tor gulator Austin Semiconductor, Inc. AS117 RAD-TOL *Stresses greater than those listed under "Absolute Maximum Operating Temperature Range ....................... -55C < Ta < +125C Ratings" may cause permanent damage to the device. This is Maximum Junction Temperature ......................................... +150C a stress rating only and functional operation of the device at Storage Temperature Range ........................... -65C < Ta < +150C these or any other conditions above those indicated in the Lead Temperature (soldering for 10 sec) ............................ 300C operation section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods Input to Output Voltage Differential ............................+40V, -0.3V may affect reliability. Power Dissipation ........................................... Internally Limited Output Short Circuit Duration..................................................10 sec Lead Temperature (Soldering, 10 sec).......................................300°C ABSOLUTE MAXIMUM RATINGS(note 1) Thermal Resistance: Theta JA TO-03 Metal Can .........still air............186C/W .......500LF/min air flow...... 64C/W Theta JA 16Lead Gullwing ....still air............... 115C/W .......500LF/min air flow....... 66C/W Theta JC TO-03 Metal Can .....still air.............. 21C/W Theta JC 16Lead Gullwing .....still air............... 3.4C/W -(see note 3) Package Weight: 16 Lead Cerpack Gullwing ................................ 380mg 3 Lead Metal Can ............................................... 950mg Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is functional , but do not guarantee specific performance limits. For guaranteed Specs & Test conditions, see Electrical Characteristics section. Note 2: The maximum power dissipation must be derated at elevated temperatures and is dictated by Tjmax(max Junction temp), ThetaJA (package junction to ambient thermal resistance), and TA(ambient temp). The maximum allowable power dissipation at any temperature is Pdmax (Tjmax - TA)/ThetaJA or the number given in the Absolute Maximum Rating, whichever is lower. Note 3: For the Ceramic 16lead gullwing, device to function properly, the “OUTPUT” and “OUTPUT/SENSE” pins must be connected on the users printed circuit board. (The following Table applies to the Subgroup column in the Electrical Characteristics Tables) SUBGROUP 1 2 3 4 5 6 7 8A 8B Description Static DC tests Static DC tests Static DC tests Dynamic Tests Dynamic Tests Dynamic Tests Functional Tests Functional Tests Functional Tests TEMP(OC) +25 +125 -55 +25 +125 -55 +25 +125 -55 RECOMMENDED OPERATING CONDITIONS: OPERATING TEMPERATURE Range INPUT VOLTAGE RANGE AS117 RAD-TOL Rev. 1.1 06/05 -55C < TA < 125c 4.25V to 41.25V Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 4 POS Adj Volta ge oltag PRELIMINARY SPECIFICATION Re gula tor gulator Austin Semiconductor, Inc. AS117 RAD-TOL Electrical Characteristics DC PARAMETERS: (SEE NOTE 1) SYMBOL Vout Vrline Vrload PARAMETER Output Voltage Line Regulation Load Regulation CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS Vin = 4.25V, Il = -5mA 1.2 1.3 V 1, 2, 3 Vin = 4.25V, Il = -500mA 1.2 1.3 V 1, 2, 3 Vin = 41.25V, Il = -5mA 1.2 1.3 V 1, 2, 3 Vin = 41.25V, Il = -50mA 1.2 1.3 V 1, 2, 3 4.25V < Vin < 41.25V, Il = -5mA -9 9 mV 1 -23 23 mV 2, 3 Vin = 6.25V, -500mA < Il < -5mA -12 12 mV 1, 2, 3 Vin = 41.25V, -50mA < Il < -5mA -12 12 mV 1, 2, 3 Vrth Thermal Regulation Vin = 14.6V, Il = -500mA -12 12 mV 1 Iadj Adjust Pin Current Vin = 4.25V, Il = -5mA -100 -15 uA 1, 2, 3 Vin = 41.25V, Il = -5mA -100 -15 uA 1, 2, 3 Delta Iadj/Line Adjust Pin Current Change 4.25V < Vin < 41.25V, Il = -5mA -5 5 uA 1, 2, 3 Delta Iadj/Load Adjust Pin Current Change Vin = 6.25V, -500mA < Il < -5mA -5 5 uA 1, 2, 3 Iq Minimum Load Current Vin = 4.25V, Forced Vout = 1.4V -3 -0.5 mA 1, 2, 3 Vin = 14.25V, Forced Vout = 1.4V -3 -0.5 mA 1, 2, 3 Vin = 41.25V, Forced Vout = 1.4V -5 -1 mA 1, 2, 3 Vin = 4.25V -1.8 -0.5 A 1, 2, 3 Vin = 40V -0.5 -0.05 A 1, 2, 3 Vin = 4.25V, Rl = 2.5 Ohms, Cl = 20uF 1.2 1.3 V 1, 2, 3 Vin = 40V, Rl = 250 Ohms 1.2 1.3 V 1, 2, 3 1.2 1.3 V 2 Ios Output Short Circuit Current Vout (Recov) Vout Output Voltage Recovery Output Voltage Recovery AS117 RAD-TOL Rev. 1.1 06/05 Vin = 6.25V, Il = -5mA 2 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 5 POS Adj Volta ge oltag PRELIMINARY SPECIFICATION Re gula tor gulator Austin Semiconductor, Inc. AS117 RAD-TOL Electrical Characteristics DC PARAMETERS: (SEE NOTE 1) SYMBOL Vstart (Continued) PARAMETER CONDITIONS NOTES Voltage Start-Up Vin = 4.25V, Rl = 2.5 Ohms, Cl = 20uF, Il = -500mA PINNAME MIN 1.2 MAX 1.3 UNIT SUBGROUPS V 1, 2, 3 dB 4 AC PARAMETERS: (SEE NOTE 1) Delta Vin/Delta Vout Ripple Rejection Vin = 6.25V, ei = 1Vrms at f = 2400Hz, Il = -125mA 65 Vno Output Noise Voltage Vin = 6.25V, Il = -50mA 120 uVrms 7 Delta Vout/Delta Vin Line Transient Response Vin = 6.25V, Delta Vin = 3V, Il = -10mA 6 mV/V 7 Delta Vout/ Delta Il Load Transient Response Vin = 6.25V, Delta Il = -200mA, Il = -50mA 0.6 mV/mA 7 DC PARAMETERS: DRIFT VALUES (The following conditions apply to all the following parameters, unless otherwise specified.) DC: "Delta calculations performed on QMLV devices at group B, subgroup 5 ONLY." Vout Output Voltage Vin = 4.25V, Il = -5mA -0.01 0.01 V 1 Vin = 4.25V, Il = -500mA -0.01 0.01 V 1 Vin = 41.25V, Il = -5mA -0.01 0.01 V 1 Vin = 41.25V, Il = -50mA -0.01 0.01 V 1 Vrline Line Regulation 4.25V < Vin < 41.25V, Il = -5mA -4 4 mV 1 Iadj Adjust Pin Current Vin = 4.25V, Il = -5mA -10 10 uA 1 Vin = 41.25V, Il = -5mA -10 10 uA 1 Vin = 4.25V, Il = -5mA 1.2 1.350 V 1 Vin = 4.25V, Il = -500mA 1.2 1.350 V 1 Vin = 41.25V, Il = -5mA 1.2 1.350 V 1 Vin = 41.25V, Il = -50mA 1.2 1.350 V 1 25 mV 1 dB 4 AC/DC PARAMETERS: POST RADIATION LIMITS +25 C (SEE NOTE 1) Vout Output Voltage Vrline Line Regulation 4.25V < Vin < 41.25V, Il = -5mA -25 Delta Vin/Delta Vout Ripple Rejection Vin = 6.25V, ei = 1Vrms at f = 2400Hz, Il = -125mA 60 Vout (Recov) Output Voltage Recovery Vin = 4.25V, Rl = 2.5 Ohms, Cl = 20uS 1.20 1.350 V 1 Vin = 40V, Rl = 250 Ohms 1.20 1.350 V 1 AS117 RAD-TOL Rev. 1.1 06/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 6 POS Adj Volta ge oltag PRELIMINARY SPECIFICATION Re gula tor gulator Austin Semiconductor, Inc. NOTE 1: Pre and Post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post Radiation Limits Table. These parts may be dose rate sensitive in a space environement and demonstrate ehnaced low dose rate effect. Radiation end point limits fro the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, Method 1019.5, Cond A. AS117 RAD-TOL NOTE 2: Tested at TA = 125C, correlated to TA = 150C. Schematic Diagram AS117 RAD-TOL Rev. 1.1 06/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 7 POS Adj Volta ge oltag PRELIMINARY SPECIFICATION Re gula tor gulator Austin Semiconductor, Inc. AS117 RAD-TOL MECHANICAL DEFINITIONS* ASI Case (Package Designator GW16) SMD 5962-99517, Case Outline Z MIL-STD-1835 outline drawing GDFP1-G16 0 D R E E1 PIN 1 L e A b C A A1 b C D E E1 e L R 0 A1 Min Max .050 .080 .004 .012 .015 .022 .004 .009 .228 .253 .400 .420 .235 .260 .050 BSC .037 .043 .013 .017 0 7 Notes: 1. Lead Finish: Solder dipped with Sn 60 or Sn63 solder conforming to MIL-PRF-38535 to a min thickness of 200 micro-inches. Solder may be applied over lead base metal or Sn plate. Max limit may be increased by .003 inches after lead finish applied. 2. Lead 1 identification shall be: a) A notch or other mark within this area. b) a TAB on lead 1, either side. *All measurements are in inches. AS117 RAD-TOL Rev. 1.1 06/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 8 POS Adj Volta ge oltag PRELIMINARY SPECIFICATION Re gula tor gulator Austin Semiconductor, Inc. AS117 RAD-TOL MECHANICAL DEFINITIONS* ASI Case (Package Designator TO-39) Mil Std 5962-99517 case X 3-Lead CAN TO-39 Case Outline L A K2 F L2 L1 b1 e1 D 3 2 e D1 b 1 A1 k1 A A1 b b1 D D1 e e1 F k k1 K2 L L1 L2 Ag Min Max .165 .195 .100 ---.016 .019 .016 .021 .335 .370 .305 .335 .200 BSC .100 BSC ---- .050 .028 .034 .029 .045 .009 .041 .500 ------- .050 .250 ---45 T.P. k Ag *All measurements are in inches. AS117 RAD-TOL Rev. 1.1 06/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 9 POS Adj Volta ge oltag PRELIMINARY SPECIFICATION Re gula tor gulator Austin Semiconductor, Inc. AS117 RAD-TOL ORDERING INFORMATION EXAMPLE: Device Number AS117 EXAMPLE: AS117PGW16/SPACE RAD Level Package Type Process P,R, or blank GW16 /* AS117RTO39/SPACE Device Number RAD Level AS117 P,R or blank Package Type Process TO39 /* + RADIATION Levels: BLANK = No Radiation Guarantee P = 30K Rads(Si) Total Dose R = 100K Rads(Si) Total Dose *AVAILABLE PROCESSES: XT = Extended Temperature Range /883C = MIL-STD-883 paragraph 1.2.1 /SPACE = MIL-STD-883 para 1.2.1 -55oC to +125oC -55oC to +125oC -55oC to +125oC NOTE: ASI supports Customer specified drawings (SCDs), please contact your SALES or Factory Representative for information. AS117 RAD-TOL Rev. 1.1 06/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 10 POS Adj Volta ge oltag PRELIMINARY SPECIFICATION Re gula tor gulator Austin Semiconductor, Inc. AS117 RAD-TOL ASI TO DSCC PART NUMBER CROSS REFERENCE ASI PART NUMBER DSCC PART NUMBER DSCC part numbers pending , contact your ASI Sales or factory rep for updated status. This will be updated in the near future to include the DSCC part numbers as soon as ASI receives certification.. * ASI part number is for reference only. Orders received referencing the SMD part number will be processed per the SMD. AS117 RAD-TOL Rev. 1.1 06/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 11