Hanbit HSD16M64B8W-10L Synchronous dram module 128mbyte(16mx64-bit), 144pin so-dimm, 4banks, 4k ref., 3.3v Datasheet

HANBit
HSD16M64B8W
Synchronous DRAM Module 128Mbyte(16Mx64-Bit), 144pin SO-DIMM,
4Banks, 4K Ref., 3.3V
HSD16M64B8W
Part No.
GENERAL DESCRIPTION
The HSD16M64B8W is a 16M x 64 bit Synchronous Dynamic RAM high density memory module. The module consists
of eight CMOS 2M x 16 bit x 4banks Synchronous DRAMs in TSOP-II 400mil packages on a 144-pin glass-epoxy
substrate. Two 0.1uF decoupling capacitors are mounted on the printed circuit board in parallel for each SDRAM. The
HSD16M64B8W is a SO-DIMM(Small Outline Dual in line Memory Module) and is intended for mounting into 144-pin
edge connector sockets. Synchronous design allows precise cycle control with the use of system clock. I/O transactions
are possible on every clock cycle. Range of operating frequencies, programmable latencies allows the same device to be
useful for a variety of high bandwidth, high performance memory system applications All module components may be
powered from a single 3.3V DC power supply and all inputs and outputs are LVTTL-compatible.
FEATURES
• Part Identification
HSD16M64B8W-10 : 100MHz (CL=2)
HSD16M64B8W-10L : 100MHz (CL=3)
HSD16M64B8W-12 : 125MHz (CL=3)
HSD16M64B8W-13 : 133MHz (CL=3)
• Burst mode operation
• Auto & self refresh capability (4096 Cycles/64ms)
• LVTTL compatible inputs and outputs
• Single 3.3V ±0.3V power supply
• MRS cycle with address key programs
- Latency (Access from column address)
- Burst length (1, 2, 4, 8 & Full page)
- Data scramble (Sequential & Interleave)
• All inputs are sampled at the positive going edge of the system clock
• The used device is 2M x 16bit x 4Banks SDRAM
URL: www.hbe.co.kr
REV 1.0 (August.2002)
1
HANBit Electronics Co.,Ltd.
HANBit
HSD16M64B8W
PIN
PIN
Front
PIN
1
Vss
2
3
DQ0
4
5
DQ1
6
7
DQ2
8
Back
ASSIGNMENT
PIN
Frontl
PIN
Back
PIN
Front
PIN
Back
Vss
49
DQ13
50
DQ45
97
DQ32
51
DQ14
52
DQ46
99
DQ22
98
DQ54
DQ23
100
DQ55
DQ33
53
DQ15
54
DQ47
DQ34
55
Vss
56
Vss
101
VCC
102
VCC
103
A6
104
A7
9
DQ3
10
DQ35
57
NC
58
NC
105
A8
106
BA0
11
VCC
12
VCC
59
NC
60
NC
107
Vss
108
Vss
13
DQ4
14
DQ36
61
CLK0
62
CKE0
109
A9
110
BA1
15
DQ4
16
DQ37
63
VCC
64
VCC
111
A10_AP
112
A11
17
DQ6
18
DQ38
65
/RAS
66
/CAS
113
VCC
114
VCC
19
DQ7
20
DQ39
67
/WE
68
CKE1
115
DQM2
116
DQM6
21
Vss
22
Vss
69
/CS0
70
NC(A12)
117
DQM3
118
DQM7
23
DQM0
24
DQM4
71
/CS1
72
NC
119
Vss
120
Vss
25
DQM1
26
DQM5
73
NC
74
CLK1
121
DQ24
122
DQ56
27
VCC
28
VCC
75
Vss
76
Vss
123
DQ25
124
DQ57
29
A0
30
A3
77
NC
78
125
DQ26
126
DQ58
31
A1
32
A4
79
NC
80
NC
127
DQ27
128
DQ59
33
A2
34
A5
81
VCC
82
VCC
129
VCC
130
VCC
35
Vss
36
Vss
83
DQ16
84
DQ48
131
DQ28
132
DQ60
37
DQ8
38
DQ40
85
DQ17
86
DQ49
133
DQ29
134
DQ61
NC
39
DQ9
40
DQ41
87
DQ18
88
DQ50
135
DQ30
136
DQ62
41
DQ10
42
DQ42
89
DQ19
90
DQ51
137
DQ31
138
DQ63
43
DQ11
44
DQ43
91
Vss
92
Vss
139
Vss
140
Vss
45
VCC
46
VCC
93
DQ20
94
DQ52
141
SDA
142
SCL
47
DQ12
48
DQ44
95
DQ21
96
DQ53
143
VCC
144
VCC
*Pin Names
Pin Name
Function
Pin Name
Function
A0 ~ A11
Address input (Multiplexed)
BA0 ~ BA1
Select bank
DQ0 ~ DQ63
Data input/output
CLK0,CLK1
Clock input
CKE0, CKE1
Clock enable input
/CS0, /CS1
Chip select input
/RAS
Row address strobe
/CAS
Column address strobe
/WE
Write enable
DQM0 ~ 7
DQM
Vcc
Power supply (3.3V)
Vss
Ground
SDA
Serial data I/O
SCL
Serial clock
NC
No connection
URL: www.hbe.co.kr
REV 1.0 (August.2002)
2
HANBit Electronics Co.,Ltd.
HANBit
HSD16M64B8W
FUNCTIONAL BLOCK DIAGRAM
DQ0-63
CKE0
/CA
CKE
CAS
/RAS
RAS
S
/CS0
U1
CLK
DQ0-7,DQ32-39
DQM0
CE
WE
A0-A11
BA0-1
CLK0
DQM0
DQM4
DQM4
CKE
CAS
CLK
DQ8-15,DQ40-47
U2
RAS
DQM1
CE
WE
A0-A11
BA0-1
DQM1
DQM5
DQM5
CKE
CAS
CLK
U3 DQ16-23,DQ48-55
RAS
DQM2
CE
WE
A0-A11
BA0-1
DQM2
DQM6
DQM6
CKE
CAS
U4
CLK
DQ24-31,DQ56-63
RAS
CE
CKE1
WE
A0-A11 BA0-1
CKE
CAS
U5
CE
DQM3
DQM7
CLK
DQ0-7,DQ32-39
RAS
/CS1
DQM3
DQM7
DQM0
WE
CKE
CAS
A0-A11 BA0-1
U6
DQM4
DQM1
WE
DQM0
DQM4
CLK
DQ8-15,DQ40-47
RAS
CE
CLK1
A0-A11
BA0-1
DQM1
DQM5
DQM5
CKE
CAS
CLK
U7 DQ16-23,DQ48-55
RAS
DQM2
CE
WE
A0-A11
BA0-1
DQM2
DQM6
DQM6
CKE
CAS
U8
CLK
DQ24-31,DQ56-63
RAS
CE
WE
A0-A11 BA0-1
DQM3
DQM3
DQM7
DQM7
/WE
A0 – A11
BA0-1
Vcc
Two 0.1uF Capacitors
per each SDRAM
Vss
URL: www.hbe.co.kr
REV 1.0 (August.2002)
3
HANBit Electronics Co.,Ltd.
HANBit
HSD16M64B8W
PIN FUNCTION DESCRIPTION
PIN
NAME
INPUT FUNCTION
CLK
System clock
Active on the positive going edge to sample all inputs.
/CS
Chip enable
Disables or enables device operation by masking or enabling all inputs except
CLK, CKE and DQM
CKE
Clock enable
Masks system clock to freeze operation from the next clock cycle.
CKE should be enabled at least one cycle prior to new command.
Disable input buffers for power down in standby.
CKE should be enabled 1CLK+tSS prior to valid command.
A0 ~ A11
Address
Row/column addresses are multiplexed on the same pins.
Row address : RA0 ~ RA11, Column address : CA0 ~ CA8
BA0 ~ BA1
Bank select address
Selects bank to be activated during row address latch time.
Selects bank for read/write during column address latch time.
/RAS
Row address strobe
Latches row addresses on the positive going edge of the CLK with RAS low.
Enables row access & precharge.
/CAS
/WE
Column
address
Latches column addresses on the positive going edge of the CLK with CAS low.
strobe
Enables column access.
Write enable
Enables write operation and row precharge.
Latches data in starting from CAS, WE active.
DQM0 ~ 7
Data
input/output
Makes data output Hi-Z, tSHZ after the clock and masks the output.
mask
Blocks data input when DQM active. (Byte masking)
DQ0 ~DQ63
Data input/output
Data inputs/outputs are multiplexed on the same pins.
VCC/VSS
Power supply/ground
Power and ground for the input buffers and the core logic.
ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
RATING
VIN ,OUT
-1V to 4.6V
Voltage on Vcc Supply Relative to Vss
Vcc
-1V to 4.6V
Power Dissipation
PD
8W
TSTG
-55oC to 150oC
Voltage on Any Pin Relative to Vss
Storage Temperature
Short Circuit Output Current
IOS
400mA
Notes:
Permanent device damage may occur if " Absolute Maximum Ratings" are exceeded. Functional operation should be
restricted to the conditions as detailed in the operational sections of this data sheet. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
URL: www.hbe.co.kr
REV 1.0 (August.2002)
4
HANBit Electronics Co.,Ltd.
HANBit
HSD16M64B8W
DC OPERATING CONDITIONS
(Recommended operating conditions (Voltage referenced to VSS = 0V, TA = 0 to 70°C) )
PARAMETER
SYMBOL
MIN
TYP.
MAX
UNIT
NOTE
Supply Voltage
Vcc
3.0
3.3
3.6
V
Input High Voltage
VIH
2.0
3.0
Vcc+0.3
V
1
Input Low Voltage
VIL
-0.3
0
0.8
V
2
Output High Voltage
VOH
2.4
-
-
V
IOH = -2mA
Output Low Voltage
VOL
-
-
0.4
V
IOL = 2mA
Input leakage current
I LI
-12
12
uA
Notes :
1. VIH (max) = 5.6V AC. The overshoot voltage duration is ≤ 3ns.
2. VIL (min) = -2.0V AC. The undershoot voltage duration is ≤ 3ns.
3. Any input 0V ≤ VIN ≤ VDDQ.
Input leakage currents include Hi-Z output leakage for all bi-directional buffers with Tri-State outputs.
3
CAPACITANCE
(VCC = 3.3V, TA = 23°C, f = 1MHz, VREF =1.4V ± 200 mV)
DESCRIPTION
SYMBOL
MIN
MAX
UNITS
Clock
CCLK
20
32
pF
/RAS, /CAS,/WE,/CS, CKE, DQM
CIN
20
40
pF
Address
CADD
20
40
pF
DQ (DQ0 ~ DQ63)
COUT
32
52
pF
DC CHARACTERISTICS
(Recommended operating condition unless otherwise noted, TA = 0 to 70°C)
TEST
PARAMETER
VERSION
SYMBOL
CONDITION
-13
-12
120
120
-10
UNIT
NOTE
mA
1
-10L
Burst length = 1
Operating current
ICC1
(One bank active)
tRC ≥ tRC(min)
112
1120
0
0
0
IO = 0mA
ICC2P
Precharge standby current in
CKE ≤ VIL(max)
8
mA
8
mA
160
mA
tCC=10ns
power-down mode
ICC2PS
CKE & CLK ≤ VIL(max)
tCC=∞
CKE ≥ VIH(min)
Precharge standby current in
CS* ( VIH(min),
tCC=10ns
ICC2N
non power-down mode
Input signals are changed
one time during 20ns
URL: www.hbe.co.kr
REV 1.0 (August.2002)
5
HANBit Electronics Co.,Ltd.
HANBit
HSD16M64B8W
CKE ( VIH(min)
CLK ≤ VIL(max), tCC=∞
ICC2NS
56
Input signals are stable
ICC3P
Active standby current in
power-down mode
ICC3PS
CKE ≤ VIL(max), tCC=10ns
40
CKE&CLK ≤ VIL(max)
mA
40
tCC=∞
CKE≥VIH(min),
CS*≥VIH(min), tCC=10ns
240
ICC3N
Active standby current in
Input signals are changed
non power-down mode
one time during 20ns
(One bank active)
CKE≥VIH(min)
ICC3NS
mA
CLK ≤VIL(max), tCC=∞
120
Input signals are stable
IO = 0 mA
Operating current
Page burst
144
116
136
ICC4
(Burst mode)
1160
4Banks Activated
0
0
176
176
mA
1
mA
2
0
tCCD = 2CLKs
Refresh current
ICC5
Self refresh current
tRC ≥ tRC(min)
ICC6
168
1680
0
0
CKE ≤ 0.2V
0
12
mA
6.4
mA
Notes :
1. Measured with outputs open.
2. Refresh period is 64ms.
3. Unless otherwise noticed, input swing level is CMOS(VIH/VIL=VDDQ/VSSQ).
AC OPERATING TEST CONDITIONS
(vcc = 3.3V ± 0.3V, TA = 0 to 70°C)
PARAMETER
AC Input levels (Vih/Vil)
Input timing measurement reference level
Input rise and fall time
Output timing measurement reference level
Output load condition
URL: www.hbe.co.kr
REV 1.0 (August.2002)
Value
UNIT
2.4/0.4
V
1.4
V
tr/tf = 1/1
Ns
1.4
V
See Fig. 2
6
HANBit Electronics Co.,Ltd.
HANBit
HSD16M64B8W
Vtt=1.4V
3.3V
3.3V
1200Ω
50Ω
DOUT
870Ω
DOUT
Z0=50Ω
50pF*
50pF
VOH (DC) = 2.4V, IOH = -2mA
VOL (DC) = 0.4V, IOL = 2mA
(Fig. 2) AC output load circuit
(Fig. 1) DC output load
circuit
OPERATING AC PARAMETER
(AC operating conditions unless otherwise noted)
VERSION
PARAMETER
SYMBOL
-13
-12
-10
-10L
UNIT
NOTE
Row active to row active delay
tRRD(min)
15
16
20
20
ns
1
RAS to CAS delay
tRP(min)
20
20
20
20
ns
1
Row precharge time
tRP(min)
20
20
20
20
ns
1
tRAS(min)
45
48
50
50
ns
1
Row active time
Row cycle time
tRAS(max)
100
tRC(min)
65
68
ns
70
70
2
ns
1
CLK
2.5
Last data in to row precharge
tRDL(min)
Last data in to Active delay
tDAL(min)
Last data in to new col. address delay
tCDL(min)
1
CLK
2
Last data in to burst stop
tBDL(min)
1
CLK
2
Col. address to col. address delay
tCCD(min)
1
CLK
3
ea
4
2 CLK + 20 ns
CAS latency=3
2
Number of valid output data
CAS latency=2
-
1
Notes :
1. The minimum number of clock cycles is determined by dividing the minimum time required with clock cycle time and
then rounding off to the next higher integer.
2. Minimum delay is required to complete write.
3. All parts allow every cycle column address change.
4. In case of row precharge interrupt, auto precharge and read burst stop.
.
URL: www.hbe.co.kr
REV 1.0 (August.2002)
7
HANBit Electronics Co.,Ltd.
HANBit
HSD16M64B8W
AC CHARACTERISTICS
(AC operating conditions unless otherwise noted)
-13
PARAMETER
MIN
CLK cycle
CAS
time
latency=3
-12
-10
-10L
SYMBOL
MAX
7.5
tCC
MIN
MAX
8
1000
MIN
MAX
10
1000
MIN
UNIT
NOTE
ns
1
ns
1,2
ns
2
MAX
10
1000
1000
CAS
-
-
10
12
latency=2
CLK to valid
CAS
output delay
latency=3
5.4
6
6
6
tSAC
CAS
-
-
6
7
latency=2
Output data
CAS
hold time
latency=3
2.7
3
3
3
tOH
CAS
-
-
3
3
latency=2
CLK high pulse width
tCH
2.5
3
3
3
ns
3
CLK low pulse width
tCL
2.5
3
3
3
ns
3
Input setup time
tSS
1.5
2
2
2
ns
3
Input hold time
tSH
0.8
1
1
1
ns
3
CLK to output in Low-Z
tSLZ
1
1
1
1
ns
3
2
CLK to output
CAS
in Hi-Z
latency=3
5.4
6
6
6
ns
-
-
6
7
ns
tSHZ
CAS
latency=2
Notes :
1. Parameters depend on programmed CAS latency.
2. If clock rising time is longer than 1ns, (tr/2-0.5)ns should be added to the parameter.
3. Assumed input rise and fall time (tr & tf) = 1ns.
If tr & tf is longer than 1ns, transient time compensation should be considered, ie., [(tr + tf)/2-1]ns should be added to
the parameter.
URL: www.hbe.co.kr
REV 1.0 (August.2002)
8
HANBit Electronics Co.,Ltd.
HANBit
HSD16M64B8W
SIMPLIFIED TRUTH TABLE
CKE
n-1
COMMAND
Register
Mode register set
Auto refresh
Entry
Self
Refresh
refres
Exit
h
Bank active & row addr.
Auto
Read &
Auto
address
H
L
L
H
H
X
/C
A
S
/W
E
L
L
L
L
X
OP code
L
L
L
H
X
X
X
X
L
H
H
H
H
X
X
X
L
L
H
H
D
Q
M
X
BA
0,1
precharge
Auto
V
H
X
L
H
L
H
X
column
V
Auto
address
precharge
L
H
L
L
X
V
H
disable
Burst Stop
Precharg
Bank selection
e
All banks
suspend
or
H
X
L
L
H
L
X
H
X
L
L
H
L
X
Entry
H
L
Exit
L
H
Entry
H
L
Exit
L
H
active power down
Precharge power
down mode
DQM
H
No operation command
H
H
X
X
X
L
V
V
V
X
X
X
X
H
X
X
X
L
H
H
H
H
X
X
X
V
V
V
L
X
X
H
X
X
X
L
H
H
H
X
3
3
3
3
Column
Address
(A0 ~
A8)
L
X
NOT
1,2
Column
Address
(A0 ~
A8)
H
H
A11
A9~A0
Row address
L
precharge
disable
A10/
AP
E
disable
Write &
Clock
H
X
/R
A
S
/C
S
precharge
disable
column
H
CKE
n
X
V
L
X
H
4
4,5
4
4,5
6
X
X
X
X
X
X
V
X
X
X
7
(V=Valid, X=Don't care, H=Logic high, L=Logic low)
Notes :
1. OP Code : Operand code
A0 ~ A11 & BA0 ~ BA1 : Program keys. (@ MRS)
2. MRS can be issued only at all banks precharge state.
A new command can be issued after 2 CLK cycles of MRS.
3. Auto refresh functions are as same as CBR refresh of DRAM.
The automatical precharge without row precharge command is meant by "Auto".
Auto/self refresh can be issued only at all banks precharge state.
4. BA0 ~ BA1 : Bank select addresses.
If both BA0 and BA1 are "Low" at read, write, row active and precharge, bank A is selected.
If both BA0 is "Low" and BA1 is "High" at read, write, row active and precharge, bank B is selected.
If both BA0 is "High" and BA1 is "Low" at read, write, row active and precharge, bank C is selected.
If both BA0 and BA1 are "High" at read, write, row active and precharge, bank D is selected.
If A10/AP is "High" at row precharge, BA0 and BA1 is ignored and all banks are selected.
5. During burst read or write with auto precharge, new read/write command can not be issued.
Another bank read/write command can be issued after the end of burst.
New row active of the associated bank can be issued at tRP after the end of burst.
6. Burst stop command is valid at every burst length.
7. DQM sampled at positive going edge of a CLK and masks the data-in at the very CLK (Write DQM latency is 0),
but makes Hi-Z state the data-out of 2 CLK cycles after. (Read DQM latency is 2)
URL: www.hbe.co.kr
REV 1.0 (August.2002)
9
HANBit Electronics Co.,Ltd.
HANBit
HSD16M64B8W
TIMING DIAGRAMS
Please refer to attached timing diagram chart (II)
PACKAGING INFORMATION
Unit : Inch [mm]
PCB Thickness: 1.0mm (0.9.t - 1.1t)
Immersion Gold PCB Pattern
ORDERING INFORMATION
Part Number
Density
Org.
HSD16M64B8W-10
128MByte
16M x 64
HSD16M64B8W-10L
128MByte
16M x 64
HSD16M64B8W-12
128MByte
16M x 64
HSD16M64B8W-13
128MByte
16M x 64
URL: www.hbe.co.kr
REV 1.0 (August.2002)
Package
144 PinSODIMM
144 PinSODIMM
144 PinSODIMM
144 PinSODIMM
10
Ref.
Vcc
MODE
4K
3.3V
SDRAM
4K
3.3V
SDRAM
4K
3.3V
SDRAM
4K
3.3V
SDRAM
MAX.frq
CL2
100MHz
CL3
100MHz
CL3
125MHz
CL 3
133MHz
HANBit Electronics Co.,Ltd.
Similar pages