Elantec EL2072CS 730 mhz closed loop buffer Datasheet

EL2072C
EL2072C
730 MHz Closed Loop Buffer
Features
General Description
# 730 MHz b 3 dB bandwidth
(0.5 VPP)
# 5 ns settling to 0.2%
# VS e g 5V @ 15 mA
# Low distortion: HD2, HD3 of
b 65 dBc at 20 MHz
# Overload/short-circuit protected
# Closed-loop, unity gain
# Low cost
# Direct replacement for CLC110
The EL2072 is a wide bandwidth, fast settling monolithic buffer
built using an advanced complementary bipolar process. This
buffer is closed loop to achieve lower output impedance and
higher gain accuracy. Designed for closed-loop unity gain, the
EL2072 has a 730 MHz b 3 dB bandwidth and 5 ns settling to
0.2% while consuming only 15 mA of supply current.
Applications
#
#
#
#
#
#
#
Video buffer
Video distribution
HDTV buffer
High-speed A/D buffer
Photodiode, CCD preamps
IF processors
High-speed communications
Ordering Information
Part No.
Temp. Range
Package
EL2072CN b 40§ C to a 85§ C 8-Pin P-DIP
EL2072CS
b 40§ C to a 85§ C 8-Pin SO
Outline Ý
The EL2072 is an obvious high-performance solution for video
distribution and line-driving applications. With low 15 mA supply current and a 70 mA output drive, performance in these
areas is assured.
The EL2072’s settling to 0.2% in 5 ns, low distortion, and ability to drive capacitive loads make it an ideal flash A/D driver.
The wide 730 MHz bandwidth and extremely linear phase allow
unmatched signal fidelity.
The EL2072 can be used inside an amplifier loop or PLL as its
wide bandwidth and fast rise time have minimal effect on loop
dynamics.
Elantec products and facilities comply with MIL-I-45028A, and
other applicable quality specifications. For information on
Elantec’s processing, see Elantec document QRA-1: Elantec’s
Processing, Monolithic Integrated Circuits.
MDP0031
MDP0027
Connection Diagram
DIP and SO Package
2072 – 1
Manufactured under U.S. Patent No. 4,893,091
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a ‘‘controlled document’’. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 1991 Elantec, Inc.
December 1995 Rev E
Top View
EL2072C
730 MHz Closed Loop Buffer
Absolute Maximum Ratings (TA e 25§ C)
Supply Voltage (VS)
Output Current
Input Voltage
g 7V
Output is short-circuit protected to ground, however, maximum reliability is obtained if
IOUT does not exceed 70 mA.
g VS
b 40§ C to a 85§ C
Operating Temperature
Junction Temperature
Storage Temperature
Thermal Resistance
175§ C
b 60§ C to a 150§ C
iJA e 95§ C/W P-DIP
iJA e 175§ C/W SO
Note: See EL2071/EL2171 for Thermal Impedance curves.
Important Note:
All parameters having Min/Max specifications are guaranteed. The Test Level column indicates the specific device testing actually
performed during production and Quality inspection. Elantec performs most electrical tests using modern high-speed automatic test
equipment, specifically the LTX77 Series system. Unless otherwise noted, all tests are pulsed tests, therefore TJ e TC e TA.
Test Level
I
II
III
IV
V
Test Procedure
100% production tested and QA sample tested per QA test plan QCX0002.
100% production tested at TA e 25§ C and QA sample tested at TA e 25§ C ,
TMAX and TMIN per QA test plan QCX0002.
QA sample tested per QA test plan QCX0002.
Parameter is guaranteed (but not tested) by Design and Characterization Data.
Parameter is typical value at TA e 25§ C for information purposes only.
DC Electrical Characteristics
Parameter
VOS
TCVOS
IB
Description
Test
Conditions
Typ
Max
Test
Level
Units
2.0
8.0
I
mV
TMIN
16.0
V
mV
TMAX
13.0
V
mV
IV
mV/§ C
Temp
Min
25§ C
Output Offset Voltage
Average Offset
Voltage Drift
Input Bias Current
25§ C b TMAX
20.0
50.0
25§ C b TMIN
20.0
100.0
25§ C, TMAX
10.0
TMIN
TCIB
AV
ILIN
Average Input Bias
Current Drift
Small Signal Gain
Integral End
Point linearity
PSRR
Power Supply
Rejection Ratio
IS
Supply CurrentÐQuiescent
RL e 100X
mA
IV
nA/§ C
I
V/V
200.0
300.0
200.0
700.0
25§ C
0.96
TMIN, TMAX
0.95
0.98
V
V/V
0.4
IV
%F.S.
TMIN
0.8
IV
%F.S.
TMAX
0.3
IV
%F.S.
II
dB
II
mA
All
2
mA
V
25§ C b TMIN
All
No Load
II
25§ C b TMAX
25§ C
g 2V F.S.
50.0
100.0
0.2
45.0
65.0
15.0
20.0
TD is 3.3in
VS e g 5V, RL e 100X, RS e 50X unless otherwise specified
EL2072C
730 MHz Closed Loop Buffer
DC Electrical Characteristics
Parameter
RIN
CIN
Description
Test
Conditions
Input Resistance
Temp
Min
Typ
25§ C
100.0
160.0
Output Impedance (DC)
IOUT
Output Current
Output Voltage Swing
kX
50.0
V
kX
V
kX
1.6
2.0
TMIN, TMAX
VOUT
I
200.0
25§ C
RL e 100X
Units
TMIN
TMIN, TMAX
ROUT
Test
Level
TMAX
25§ C
Input Capacitance
Max
25§ C, TMAX
50.0
TMIN
45.0
25§ C, TMAX
g 3.2
TMIN
g 3.0
2.2
IV
pF
2.5
IV
pF
3.0
IV
X
3.5
IV
X
II
mA
V
mA
II
V
V
V
70.0
g 4.0
TD is 2.4in
VS e g 5V, RL e 100X, RS e 50X unless otherwise specified Ð Contd.
AC Electrical Characteristics VS e g 5V, RL e 100X, RS e 50X unless otherwise specified
Parameter
Description
Test
Conditions
Test
Level
Units
V
MHz
400.0
IV
MHz
300.0
IV
MHz
Temp
Min
Typ
25§ C
400.0
730.0
TMIN
TMAX
Max
FREQUENCY RESPONSE
SSBW
LSBW
b 3 dB Bandwidth
(VOUT k 0.5 VPP)
b 3 dB Bandwidth
(VOUT e 5.0 VPP)
25§ C
55.0
TMIN, TMAX
50.0
90.0
IV
MHz
IV
MHz
GFPL
GFR
GDL
Peaking
VOUT k 0.5 VPP
k 200 MHz
Rolloff
VOUT k 0.5 VPP
k 200 MHz
Group Delay
k 200 MHz
25§ C
0.5
V
dB
TMAX
0.6
IV
dB
TMIN
0.8
IV
dB
25§ C
0.0
0.8
V
dB
TMIN
1.0
IV
dB
TMAX
1.2
IV
dB
25§ C, TMIN
0.0
0.75
TMAX
LPD
Linear Phase Deviation
VOUT k 0.5 VPP
k 200 MHz
25§ C, TMIN
TMAX
3
0.7
1.0
IV
ns
1.2
IV
ns
1.5
IV
§
2.0
IV
§
TD is 3.5in
GAIN FLATNESS
EL2072C
730 MHz Closed Loop Buffer
AC Electrical Characteristics Ð Contd.
VS e g 5V, RL e 100X, RS e 50X unless otherwise specified
Parameter
Description
Test
Conditions
Temp
Min
Typ
Max
Test
Level
Units
TIME-DOMAIN RESPONSE
TR1, TF1
TR2, TF2
Rise Time, Fall Time
Input Signal Rise/Fall e 300 ps
0.5V Step
Rise Time, Fall Time
5.0V Step
0.4
TMAX
Input Signal Rise/Fall s 1 ns
25§ C
4.5
TMIN, TMAX
TS1
Settling Time to 0.2%
Input Signal Rise/Fall s 1 ns
2.0V Step
OS
Overshoot
Input Signal Rise/Fall e 300 ps
0.5V Step
SR
25§ C, TMIN
All
5.0
25§ C
0.0
TMIN, TMAX
25§ C
500.0
TMIN, TMAX
450.0
Slew Rate
1.0
IV
ns
1.4
IV
ns
7.5
IV
ns
8.5
IV
ns
10.0
IV
ns
10.0
IV
%
15.0
IV
%
IV
V/ms
IV
V/ms
800.0
DISTORTION
HD2
HD2A
HD3
HD3A
2nd Harmonic Distortion
at 20 MHz
2nd Harmonic Distortion
at 50 MHz
25§ C
2 VPP
2 VPP
b 50.0
V
dBc
TMIN
b 48.0
IV
dBc
TMAX
b 55.0
IV
dBc
b 45.0
IV
dBc
b 40.0
IV
dBc
b 55.0
V
dBc
b 55.0
IV
dBc
b 50.0
IV
dBc
b 45.0
IV
dBc
b 155.0
IV
dBm (1 Hz)
b 154.0
IV
dBm (1 Hz)
57.0
IV
mV
63.0
IV
mV
25§ C , TMAX
b 55.0
b 50.0
TMIN
3rd Harmonic Distortion
at 20 MHz
2 VPP
3rd Harmonic Distortion
at 50 MHz
2 VPP
25§ C
b 65.0
TMIN, TMAX
25§ C , TMIN
b 60.0
TMAX
NF
Noise Floor
l 100 kHz
25§ C, TMIN
INV
Integrated Noise
100 kHz to 200 MHz
25§ C, TMIN
b 158.0
TMAX
TMAX
4
40.0
TD is 5.1in
EQUIVALENT INPUT NOISE
EL2072C
730 MHz Closed Loop Buffer
Typical Performance Curves (VS e g 5V, RL e 100X, RS e 50X)
Forward Gain and Phase
Gain Flatness & Deviation
from Linear Phase
Reverse Gain and phase
Input Impedance
Output Impedance
Recommended RS vs
Load Capacitance
Integral Linearity Error
Frequency Response vs Rload
lS21l vs Cload
with Recommended Rs
2072 – 2
5
EL2072C
730 MHz Closed Loop Buffer
Typical Performance Curves (VS e g 5V, RL e 100X, RS e 50X) Ð Contd.
Small Signal
Pulse Response
Large Signal
Pulse Response
Long-Term
Settling Time
2nd Harmonic Distortion
3rd Harmonic Distortion
2-Tone, 3rd Order
Intermodulation Intercept
2072 – 3
6
EL2072C
730 MHz Closed Loop Buffer
Burn-In Circuit
2072 – 4
Increasing capacitance on the output of the
EL2072 will add phase shift, decreasing phase
margin and increasing frequency-response peaking. A small series resistor before the capacitance
decouples this effect, and should be used for large
capacitance values. Please refer to the graphs for
the appropriate resistor value to be used.
Printed Circuit Layout
As with any high-frequency device, good PCB
layout is necessary for optimum performance.
This is especially important for the EL2072,
which has a typical bandwidth of 730 MHz.
Ground plane construction is a requirement, as is
good power-supply bypassing close to the package. A closely-placed 0.01 mF ceramic capacitor
between each supply pin and the ground plane is
usually sufficient decoupling.
Pins 2, 3, 6, and 7 should be connected to the
ground-plane to minimize capacitive feedthrough, and all input and output traces should
be laid out as transmission lines and terminated
as close to the EL2072 package as possible.
7
EL2072C
EL2072C
730 MHz Closed Loop Buffer
General Disclaimer
Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes
in the circuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any
circuits described herein and makes no representations that they are free from patent infringement.
December 1995 Rev E
WARNING Ð Life Support Policy
Elantec, Inc. products are not authorized for and should not be
used within Life Support Systems without the specific written
consent of Elantec, Inc. Life Support systems are equipment intended to support or sustain life and whose failure to perform
when properly used in accordance with instructions provided can
be reasonably expected to result in significant personal injury or
death. Users contemplating application of Elantec, Inc. products
in Life Support Systems are requested to contact Elantec, Inc.
factory headquarters to establish suitable terms & conditions for
these applications. Elantec, Inc.’s warranty is limited to replacement of defective components and does not cover injury to persons or property or other consequential damages.
Elantec, Inc.
1996 Tarob Court
Milpitas, CA 95035
Telephone: (408) 945-1323
(800) 333-6314
Fax: (408) 945-9305
European Office: 44-71-482-4596
8
Printed in U.S.A.
Similar pages