Cypress CY14B104NA-BA25IT 4-mbit (512 k x 8/256 k x 16) nvsram Datasheet

CY14B104LA, CY14B104NA
4-Mbit (512 K × 8/256 K × 16) nvSRAM
4-Mbit (512 K × 8/256 K × 16) nvSRAM
Features
■
Packages
❐ 44-/54-pin thin small outline package (TSOP) Type II
❐ 48-ball fine-pitch ball grid array (FBGA)
Pb-free and restriction of hazardous substances (RoHS)
compliant
■
20 ns, 25 ns, and 45 ns access times
■
Internally organized as 512 K × 8 (CY14B104LA) or 256 K × 16
(CY14B104NA)
■
■
Hands off automatic STORE on power-down with only a small
capacitor
Functional Description
■
STORE to QuantumTrap non-volatile elements initiated by
software, device pin, or AutoStore on power-down
■
RECALL to SRAM initiated by software or power-up
■
Infinite read, write, and recall cycles
■
1 million STORE cycles to QuantumTrap
■
20 year data retention
■
Single 3 V +20, –10 operation
■
Industrial temperature
The Cypress CY14B104LA/CY14B104NA is a fast static RAM
(SRAM), with a non-volatile element in each memory cell. The
memory is organized as 512 K bytes of 8 bits each or 256 K
words of 16-bits each. The embedded non-volatile elements
incorporate QuantumTrap technology, producing the world’s
most reliable non-volatile memory. The SRAM provides infinite
read and write cycles, while independent non-volatile data
resides in the highly reliable QuantumTrap cell. Data transfers
from the SRAM to the non-volatile elements (the STORE
operation) takes place automatically at power-down. On
power-up, data is restored to the SRAM (the RECALL operation)
from the non-volatile memory. Both the STORE and RECALL
operations are also available under software control.
Logic Block Diagram [1, 2, 3]
A0
A1
A2
A3
A4
A5
A6
A7
A8
A17
A18
VCC
Quatrum Trap
2048 X 2048
R
O
W
VCAP
POWER
CONTROL
STORE
RECALL
D
E
C
O
D
E
R
STORE/RECALL
CONTROL
STATIC RAM
ARRAY
2048 X 2048
SOFTWARE
DETECT
HSB
A14 - A2
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
I
N
P
U
T
B
U
F
F
E
R
S
COLUMN I/O
OE
COLUMN DEC
WE
DQ12
DQ13
CE
DQ14
BLE
A9 A10 A11 A12 A13 A14 A15 A16
DQ15
BHE
Notes
1. Address A0–A18 for × 8 configuration and Address A0–A17 for × 16 configuration.
2. Data DQ0–DQ7 for × 8 configuration and Data DQ0–DQ15 for × 16 configuration.
3. BHE and BLE are applicable for × 16 configuration only.
Cypress Semiconductor Corporation
Document Number: 001-49918 Rev. *M
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised September 3, 2012
CY14B104LA, CY14B104NA
Contents
Pinouts .............................................................................. 3
Pin Definitions .................................................................. 4
Device Operation .............................................................. 5
SRAM Read ................................................................ 5
SRAM Write ................................................................. 5
AutoStore Operation .................................................... 5
Hardware STORE Operation ....................................... 5
Hardware RECALL (Power-Up) .................................. 6
Software STORE ......................................................... 6
Software RECALL ....................................................... 6
Preventing AutoStore .................................................. 7
Data Protection ............................................................ 7
Maximum Ratings ............................................................. 8
Operating Range ............................................................... 8
DC Electrical Characteristics .......................................... 8
Data Retention and Endurance ....................................... 9
Capacitance ...................................................................... 9
Thermal Resistance .......................................................... 9
AC Test Loads ................................................................ 10
AC Test Conditions ........................................................ 10
AC Switching Characteristics ....................................... 11
Document Number: 001-49918 Rev. *M
Switching Waveforms .................................................... 11
AutoStore/Power-Up RECALL ....................................... 14
Switching Waveforms –
AutoStore/Power-up RECALL ....................................... 14
Software Controlled STORE/RECALL Cycle ................ 15
Switching Waveforms –
Software Controlled STORE/RECALL Cycle ................ 15
Hardware STORE Cycle ................................................. 16
Switching Waveforms – Hardware STORE Cycle ........ 16
Truth Table For SRAM Operations ................................ 17
Ordering Information ...................................................... 18
Ordering Code Definitions ......................................... 19
Package Diagrams .......................................................... 20
Acronyms ........................................................................ 23
Document Conventions ................................................. 23
Units of Measure ....................................................... 23
Document History Page ................................................. 24
Sales, Solutions, and Legal Information ...................... 26
Worldwide Sales and Design Support ....................... 26
Products .................................................................... 26
PSoC Solutions ......................................................... 26
Page 2 of 26
CY14B104LA, CY14B104NA
Pinouts
Figure 1. 48-ball FBGA pinouts
48-ball FBGA
48-ball FBGA
(× 8)
Top View
(not to scale)
(× 16)
Top View
(not to scale)
1
2
3
4
5
6
A
BLE
OE
A0
A1
A2
NC
A
NC
B
DQ8
BHE
A3
A4
CE
DQ0
B
NC
DQ4
C
DQ9 DQ10
A5
A6
DQ1
DQ2
C
A7
DQ5
VCC
D
VSS
A17
A7
DQ3
VCC
D
2
3
4
5
6
NC
OE
A0
A1
A2
NC
NC
NC
A3
A4
CE
DQ0
NC
A5
A6
VSS
DQ1
A17
1
DQ11
VCC
DQ2
VCAP
A16
DQ6
VSS
E
VCC DQ12
VCAP
A16
DQ4
VSS
E
DQ3
NC
A14
A15
NC
DQ7
F
DQ14 DQ13
A14
A15
DQ5
DQ6
F
NC
HSB
A12
A13
WE
NC
G
DQ15 HSB
A12
A13
WE
DQ7
G
A18
A8
A9
A10
A11
H
NC
A9
A10
A11
NC
H
44
43
42
41
40
39
38
37
36
35
34
33
32
31
A17
A16
A15
OE
BHE
NC
[4]
[4]
A8
Figure 2. 44-pin TSOP II pinouts
(× 8)
NC
[5]
NC
A0
A1
A2
A3
A4
CE
DQ0
DQ1
VCC
VSS
DQ2
DQ3
WE
A5
A6
A7
A8
A9
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
44-pin TSOP II
(× 8)
Top View
(not to scale)
(× 16)
44
43
42
41
40
39
38
37
36
35
34
33
32
31
HSB
NC
[4]
NC
A18
A17
A16
A15
OE
DQ7
DQ6
VSS
VCC
DQ5
DQ4
30
29
28
27
26
25
24
23
VCAP
A14
A13
A12
A11
A10
NC
NC
A0
A1
A2
A3
A4
CE
DQ0
DQ1
DQ2
DQ3
VCC
VSS
DQ4
DQ5
DQ6
DQ7
WE
A5
A6
A7
A8
A9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
[6]
44-pin TSOP II
(× 16)
Top View
(not to scale)
30
29
28
27
26
25
24
23
BLE
DQ15
DQ14
DQ13
DQ12
VSS
VCC
DQ11
DQ10
DQ9
DQ8
VCAP
A14
A13
A12
A11
A10
Notes
4. Address expansion for 8-Mbit. NC pin not connected to die.
5. Address expansion for 16-Mbit. NC pin not connected to die.
6. HSB pin is not available in 44-pin TSOP II (× 16) package.
Document Number: 001-49918 Rev. *M
Page 3 of 26
CY14B104LA, CY14B104NA
Pinouts (continued)
Figure 3. Pin Diagram – 54-pin TSOP II pinout
NC
[7]
NC
A0
A1
A2
A3
A4
CE
DQ0
DQ1
DQ2
DQ3
VCC
VSS
DQ4
DQ5
DQ6
DQ7
WE
A5
A6
A7
A8
A9
NC
NC
NC
54
1
53
2
52
3
51
4
50
5
49
6
48
7
47
8
46
9
45
10
54-pin TSOP II
44
11
(× 16)
43
12
42
13
Top View
41
14
(not to scale)
40
15
39
16
38
17
37
18
36
19
35
20
34
21
33
22
32
23
31
24
30
25
29
26
27
28
HSB
NC [8]
A17
A16
A15
OE
BHE
BLE
DQ15
DQ14
DQ13
DQ12
VSS
VCC
DQ11
DQ10
DQ9
DQ8
VCAP
A14
A13
A12
A11
A10
NC
NC
NC
Pin Definitions
Pin Name
I/O Type
Description
A0–A18
Input
Address inputs. Used to select one of the 524,288 bytes of the nvSRAM for × 8 Configuration.
Address inputs. Used to Select one of the 262,144 words of the nvSRAM for × 16 Configuration.
A0–A17
DQ0–DQ7 Input/Output Bidirectional data I/O lines for × 8 configuration. Used as input or output lines depending on operation.
DQ0–DQ15
Bidirectional data I/O lines for × 16 configuration. Used as input or output lines depending on
operation.
WE
Input
Write Enable input, Active LOW. When selected LOW, data on the I/O pins is written to the specific
address location.
Input
Chip Enable input, Active LOW. When LOW, selects the chip. When HIGH, deselects the chip.
CE
Input
Output Enable, Active LOW. The active LOW OE input enables the data output buffers during read
OE
cycles. I/O pins are tristated on deasserting OE HIGH.
Input
Byte High Enable, Active LOW. Controls DQ15–DQ8.
BHE
Input
Byte Low Enable, Active LOW. Controls DQ7–DQ0.
BLE
VSS
Ground
Ground for the device. Must be connected to the ground of the system.
Power supply Power supply inputs to the device.
VCC
[9]
Input/Output Hardware STORE Busy (HSB). When LOW this output indicates that a Hardware STORE is in progress.
HSB
When pulled LOW external to the chip it initiates a non-volatile STORE operation. After each Hardware
and Software STORE operation, HSB is driven HIGH for a short time (tHHHD) with standard output high
current, and then a weak internal pull-up resistor keeps this pin HIGH (external pull-up resistor connection
optional).
Power supply AutoStore Capacitor. Supplies power to the nvSRAM during power loss to store data from SRAM to
VCAP
non-volatile elements.
NC
No connect No Connect. This pin is not connected to the die.
Notes
7. Address expansion for 16-Mbit. NC pin not connected to die.
8. Address expansion for 8-Mbit. NC pin not connected to die.
9. HSB pin is not available in 44-pin TSOP II (× 16) package.
Document Number: 001-49918 Rev. *M
Page 4 of 26
CY14B104LA, CY14B104NA
The CY14B104LA/CY14B104NA nvSRAM is made up of two
functional components paired in the same physical cell. They are
a SRAM memory cell and a non-volatile QuantumTrap cell. The
SRAM memory cell operates as a standard fast static RAM. Data
in the SRAM is transferred to the non-volatile cell (the STORE
operation), or from the non-volatile cell to the SRAM (the
RECALL operation). Using this unique architecture, all cells are
stored and recalled in parallel. During the STORE and RECALL
operations, SRAM read and write operations are inhibited. The
CY14B104LA/CY14B104NA supports infinite reads and writes
similar to a typical SRAM. In addition, it provides infinite RECALL
operations from the non-volatile cells and up to 1 million STORE
operations. Refer to the Truth Table For SRAM Operations on
page 17 for a complete description of read and write modes.
SRAM Read
The CY14B104LA/CY14B104NA performs a read cycle when
CE and OE are LOW and WE and HSB are HIGH. The address
specified on pins A0–18 or A0–17 determines which of the 524,288
data bytes or 262,144 words of 16 bits each are accessed. Byte
enables (BHE, BLE) determine which bytes are enabled to the
output, in the case of 16-bit words. When the read is initiated by
an address transition, the outputs are valid after a delay of tAA
(read cycle 1). If the read is initiated by CE or OE, the outputs
are valid at tACE or at tDOE, whichever is later (read cycle 2). The
data output repeatedly responds to address changes within the
tAA access time without the need for transitions on any control
input pins. This remains valid until another address change or
until CE or OE is brought HIGH, or WE or HSB is brought LOW.
SRAM Write
A write cycle is performed when CE and WE are LOW and HSB
is HIGH. The address inputs must be stable before entering the
write cycle and must remain stable until CE or WE goes HIGH at
the end of the cycle. The data on the common I/O pins DQ0–15
are written into the memory if the data is valid (tSD time) before
the end of a WE controlled write or before the end of an CE
controlled write. The Byte Enable inputs (BHE, BLE) determine
which bytes are written, in the case of 16-bit words. It is recommended that OE be kept HIGH during the entire write cycle to
avoid data bus contention on common I/O lines. If OE is left LOW,
internal circuitry turns off the output buffers tHZWE after WE goes
LOW.
AutoStore Operation
The CY14B104LA/CY14B104NA stores data to the nvSRAM
using one of the following three storage operations: Hardware
STORE activated by the HSB; Software STORE activated by an
address sequence; AutoStore on device power-down. The
AutoStore operation is a unique feature of QuantumTrap
technology
and
is
enabled
by
default
on
the
CY14B104LA/CY14B104NA.
During a normal operation, the device draws current from VCC to
charge a capacitor connected to the VCAP pin. This stored
charge is used by the chip to perform a single STORE operation.
If the voltage on the VCC pin drops below VSWITCH, the part
automatically disconnects the VCAP pin from VCC. A STORE
operation is initiated with power provided by the VCAP capacitor.
Note If the capacitor is not connected to VCAP pin, AutoStore
must be disabled using the soft sequence specified in Preventing
AutoStore on page 7. In case AutoStore is enabled without a
capacitor on VCAP pin, the device attempts an AutoStore
operation without sufficient charge to complete the Store. This
corrupts the data stored in nvSRAM.
Figure 4 shows the proper connection of the storage capacitor
(VCAP) for automatic store operation. Refer to DC Electrical
Characteristics on page 8 for the size of VCAP. The voltage on
the VCAP pin is driven to VCC by a regulator on the chip. A pull-up
should be placed on WE to hold it inactive during power-up. This
pull-up is effective only if the WE signal is tristate during
power-up. Many MPUs tristate their controls on power-up. This
should be verified when using the pull-up. When the nvSRAM
comes out of power-on-RECALL, the MPU must be active or the
WE held inactive until the MPU comes out of reset.
To reduce unnecessary non-volatile stores, AutoStore and
hardware STORE operations are ignored unless at least one
write operation has taken place since the most recent STORE or
RECALL cycle. Software initiated STORE cycles are performed
regardless of whether a write operation has taken place. The
HSB signal is monitored by the system to detect if an AutoStore
cycle is in progress.
Figure 4. AutoStore Mode
VCC
0.1 uF
10 kOhm
Device Operation
VCC
WE
VCAP
VSS
VCAP
Hardware STORE Operation
The CY14B104LA/CY14B104NA provides the HSB[10] pin to
control and acknowledge the STORE operations. The HSB pin
is used to request a hardware STORE cycle. When the HSB pin
is driven LOW, the CY14B104LA/CY14B104NA conditionally
initiates a STORE operation after tDELAY. An actual STORE cycle
only begins if a write to the SRAM has taken place since the last
STORE or RECALL cycle. The HSB pin also acts as an open
drain driver (internal 100 k weak pull-up resistor) that is internally driven LOW to indicate a busy condition when the STORE
(initiated by any means) is in progress.
Note After each Hardware and Software STORE operation HSB
is driven HIGH for a short time (tHHHD) with standard output high
current and then remains HIGH by internal 100 k pull-up
resistor.
Note
10. HSB pin is not available in 44-pin TSOP II (× 16) package.
Document Number: 001-49918 Rev. *M
Page 5 of 26
CY14B104LA, CY14B104NA
SRAM write operations that are in progress when HSB is driven
LOW by any means are given time (tDELAY) to complete before
the STORE operation is initiated. However, any SRAM write
cycles requested after HSB goes LOW are inhibited until HSB
returns HIGH. In case the write latch is not set, HSB is not driven
LOW by the CY14B104LA/CY14B104NA. But any SRAM read
and write cycles are inhibited until HSB is returned HIGH by MPU
or other external source.
During any STORE operation, regardless of how it is initiated,
the CY14B104LA/CY14B104NA continues to drive the HSB pin
LOW, releasing it only when the STORE is complete. Upon
completion of the STORE operation, the nvSRAM memory
access is inhibited for tLZHSB time after HSB pin returns HIGH.
Leave the HSB unconnected if it is not used.
1. Read address 0x4E38 Valid READ
2. Read address 0xB1C7 Valid READ
3. Read address 0x83E0 Valid READ
4. Read address 0x7C1F Valid READ
5. Read address 0x703F Valid READ
6. Read address 0x8FC0 Initiate STORE cycle
The software sequence may be clocked with CE controlled reads
or OE controlled reads, with WE kept HIGH for all the six READ
sequences. After the sixth address in the sequence is entered,
the STORE cycle commences and the chip is disabled. HSB is
driven LOW. After the tSTORE cycle time is fulfilled, the SRAM is
activated again for the read and write operation.
Software RECALL
Hardware RECALL (Power-Up)
During power-up or after any low power condition
(VCC< VSWITCH), an internal RECALL request is latched. When
VCC again exceeds the VSWITCH on power up, a RECALL cycle
is automatically initiated and takes tHRECALL to complete. During
this time, the HSB pin is driven LOW by the HSB driver and all
reads and writes to nvSRAM are inhibited.
Software STORE
Data is transferred from the SRAM to the non-volatile memory
by
a
software
address
sequence.
The
CY14B104LA/CY14B104NA software STORE cycle is initiated
by executing sequential CE or OE controlled read cycles from six
specific address locations in exact order. During the STORE
cycle an erase of the previous non-volatile data is first performed,
followed by a program of the non-volatile elements. After a
STORE cycle is initiated, further input and output are disabled
until the cycle is completed.
Because a sequence of reads from specific addresses is used
for STORE initiation, it is important that no other read or write
accesses intervene in the sequence, or the sequence is aborted
and no STORE or RECALL takes place.
Data is transferred from the non-volatile memory to the SRAM
by a software address sequence. A software RECALL cycle is
initiated with a sequence of read operations in a manner similar
to the software STORE initiation. To initiate the RECALL cycle,
perform the following sequence of CE or OE controlled read
operations must be performed.
1. Read address 0x4E38 Valid READ
2. Read address 0xB1C7 Valid READ
3. Read address 0x83E0 Valid READ
4. Read address 0x7C1F Valid READ
5. Read address 0x703F Valid READ
6. Read address 0x4C63 Initiate RECALL cycle
Internally, RECALL is a two step procedure. First, the SRAM data
is cleared; then, the non-volatile information is transferred into
the SRAM cells. After the tRECALL cycle time, the SRAM is again
ready for read and write operations. The RECALL operation
does not alter the data in the non-volatile elements.
To initiate the software STORE cycle, the following read
sequence must be performed.
Table 1. Mode Selection
CE
WE
OE
BHE, BLE[11]
A15–A0[12]
Mode
I/O
Power
H
X
X
X
X
Not selected
Output high Z
Standby
L
H
L
L
X
Read SRAM
Output data
Active
L
L
X
L
X
Write SRAM
Input data
Active
L
H
L
X
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x8B45
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
AutoStore
Disable
Output data
Output data
Output data
Output data
Output data
Output data
Active[13]
Notes
11. BHE and BLE are applicable for × 16 configuration only.
12. While there are 19 address lines on the CY14B104LA (18 address lines on the CY14B104NA), only 13 address lines (A14–A2) are used to control software modes.
The remaining address lines are don’t care.
13. The six consecutive address locations must be in the order listed. WE must be HIGH during all six cycles to enable a non-volatile cycle.
Document Number: 001-49918 Rev. *M
Page 6 of 26
CY14B104LA, CY14B104NA
Table 1. Mode Selection (continued)
CE
WE
OE
BHE, BLE[11]
A15–A0[12]
Mode
I/O
Power
L
H
L
X
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x4B46
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
AutoStore
Enable
Output data
Output data
Output data
Output data
Output data
Output data
Active[14]
L
H
L
X
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x8FC0
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Non-volatile
STORE
Output data
Output data
Output data
Output data
Output data
Output high Z
Active ICC2[14]
L
H
L
X
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x4C63
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Non-volatile
RECALL
Output data
Output data
Output data
Output data
Output data
Output high Z
Active[14]
Preventing AutoStore
The AutoStore function is disabled by initiating an AutoStore
disable sequence. A sequence of read operations is performed
in a manner similar to the software STORE initiation. To initiate
the AutoStore disable sequence, the following sequence of CE
or OE controlled read operations must be performed:
1. Read address 0x4E38 Valid READ
2. Read address 0xB1C7 Valid READ
3. Read address 0x83E0 Valid READ
4. Read address 0x7C1F Valid READ
5. Read address 0x703F Valid READ
6. Read address 0x8B45 AutoStore Disable
The AutoStore is re-enabled by initiating an AutoStore enable
sequence. A sequence of read operations is performed in a
manner similar to the software RECALL initiation. To initiate the
AutoStore enable sequence, the following sequence of CE or OE
controlled read operations must be performed:
1. Read address 0x4E38 Valid READ
2. Read address 0xB1C7 Valid READ
3. Read address 0x83E0 Valid READ
4. Read address 0x7C1F Valid READ
5. Read address 0x703F Valid READ
6. Read address 0x4B46 AutoStore Enable
If the AutoStore function is disabled or re-enabled, a manual
STORE operation (hardware or software) must be issued to save
the AutoStore state through subsequent power-down cycles.
The part comes from the factory with AutoStore enabled and
0x00 written in all cells.
Data Protection
The CY14B104LA/CY14B104NA protects data from corruption
during low voltage conditions by inhibiting all externally initiated
STORE and write operations. The low voltage condition is
detected
when
VCC
<
VSWITCH.
If
the
CY14B104LA/CY14B104NA is in a write mode (both CE and WE
are LOW) at power-up, after a RECALL or STORE, the write is
inhibited until the SRAM is enabled after tLZHSB (HSB to output
active). This protects against inadvertent writes during power-up
or brown out conditions.
Note
14. The six consecutive address locations must be in the order listed. WE must be HIGH during all six cycles to enable a non-volatile cycle.
Document Number: 001-49918 Rev. *M
Page 7 of 26
CY14B104LA, CY14B104NA
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage temperature ................................–65 C to +150 C
Maximum accumulated storage time
Transient voltage (< 20 ns) on
any pin to ground potential ................. –2.0 V to VCC + 2.0 V
Package power dissipation
capability (TA = 25 °C) ..................................................1.0 W
Surface mount Pb soldering
temperature (3 Seconds) .........................................+260 C
At 150 C ambient temperature ....................... 1000 h
DC output current (1 output at a time, 1s duration) .....15 mA
At 85 C ambient temperature ......................20 Years
Static discharge voltage
(per MIL-STD-883, Method 3015) .......................... > 2001 V
Maximum junction temperature .................................. 150 C
Supply voltage on VCC relative to VSS .......... –0.5 V to 4.1 V
Voltage applied to outputs
in high Z state ..................................... –0.5 V to VCC + 0.5 V
Input voltage ........................................ –0.5 V to Vcc + 0.5 V
Latch up current .................................................... > 200 mA
Operating Range
Range
Industrial
Ambient Temperature
VCC
–40 C to +85 C
2.7 V to 3.6 V
DC Electrical Characteristics
Over the Operating Range
Parameter
Description
VCC
Power supply
ICC1
Average VCC current
ICC2
ICC3
ICC4
ISB
IIX[16]
IOZ
VIH
VIL
VOH
VOL
Average VCC current during
STORE
Average VCC current at
tRC= 200 ns, VCC(Typ), 25 °C
Average VCAP current during
AutoStore cycle
VCC standby current
Test Conditions
tRC = 20 ns
tRC = 25 ns
tRC = 45 ns
Values obtained without output loads
(IOUT = 0 mA)
All inputs don’t care, VCC = Max
Average current for duration tSTORE
All inputs cycling at CMOS levels.
Values obtained without output loads
(IOUT = 0 mA).
All inputs don’t care. Average current for
duration tSTORE
CE > (VCC – 0.2 V).
VIN < 0.2 V or > (VCC – 0.2 V).
Standby current level after non-volatile
cycle is complete.
Inputs are static. f = 0 MHz.
VCC = Max, VSS < VIN < VCC
Input leakage current (except
HSB)
Input leakage current (for HSB) VCC = Max, VSS < VIN < VCC
Off-state output leakage current VCC = Max, VSS < VOUT < VCC,
CE or OE > VIH or
BHE/BLE > VIH or WE < VIL
Input HIGH voltage
Input LOW voltage
Output HIGH voltage
IOUT = –2 mA
Output LOW voltage
IOUT = 4 mA
Min
2.7
–
Typ [15]
3.0
–
Max
3.6
70
70
52
Unit
V
mA
mA
mA
–
–
10
mA
–
35
–
mA
–
–
5
mA
–
–
5
mA
–1
–
+1
A
–100
–1
–
–
+1
+1
A
A
2.0
Vss – 0.5
2.4
–
–
–
–
–
VCC + 0.5
0.8
–
0.4
V
V
V
V
Notes
15. Typical values are at 25 °C, VCC = VCC(Typ). Not 100% tested.
16. The HSB pin has IOUT = –2 µA for VOH of 2.4 V when both active HIGH and LOW drivers are disabled. When they are enabled standard VOH and VOL are valid. This
parameter is characterized but not tested.
Document Number: 001-49918 Rev. *M
Page 8 of 26
CY14B104LA, CY14B104NA
DC Electrical Characteristics (continued)
Over the Operating Range
Parameter
Description
Test Conditions
VCAP[17]
Storage capacitor
Between VCAP pin and VSS
Maximum voltage driven on VCAP VCC = Max
VVCAP[18, 19]
pin by the device
Min
61
–
Typ [15]
68
–
Max
180
VCC
Unit
F
V
Data Retention and Endurance
Over the Operating Range
Parameter
Description
Min
Unit
20
Years
1,000
K
Max
Unit
7
pF
Input capacitance (for BHE, BLE
and HSB)
8
pF
Output capacitance (except HSB)
7
pF
Output capacitance (for HSB)
8
pF
DATAR
Data retention
NVC
Non-volatile STORE operations
Capacitance
Parameter[19]
CIN
COUT
Description
Test Conditions
Input capacitance (except BHE,
BLE and HSB)
TA = 25 C, f = 1 MHz, VCC = VCC(Typ)
Thermal Resistance
Parameter[19]
Description
JA
Thermal resistance
(junction to ambient)
JC
Thermal resistance
(junction to case)
Test Conditions
Test conditions follow
standard test methods and
procedures for measuring
thermal impedance, in
accordance with
EIA/JESD51.
48-pin FBGA 44-pin TSOP II 54-pin TSOP II Unit
46.09
43.3
42.03
C/W
7.84
5.56
6.08
C/W
Notes
17. Min VCAP value guarantees that there is a sufficient charge available to complete a successful AutoStore operation. Max VCAP value guarantees that the capacitor on
VCAP is charged to a minimum voltage during a Power-Up RECALL cycle so that an immediate power-down cycle can complete a successful AutoStore. Therefore it
is always recommended to use a capacitor within the specified min and max limits. Refer application note AN43593 for more details on VCAP options.
18. Maximum voltage on VCAP pin (VVCAP) is provided for guidance when choosing the VCAP capacitor. The voltage rating of the VCAP capacitor across the operating
temperature range should be higher than the VVCAP voltage.
19. These parameters are guaranteed by design and are not tested.
Document Number: 001-49918 Rev. *M
Page 9 of 26
CY14B104LA, CY14B104NA
AC Test Loads
Figure 5. AC Test Loads
577 
3.0 V
577 
3.0 V
R1
for tristate specs
R1
OUTPUT
OUTPUT
30 pF
R2
789 
5 pF
R2
789 
AC Test Conditions
Input pulse levels ................................................... 0 V to 3 V
Input rise and fall times (10%–90%) ........................... < 3 ns
Input and output timing reference levels ...................... 1.5 V
Document Number: 001-49918 Rev. *M
Page 10 of 26
CY14B104LA, CY14B104NA
AC Switching Characteristics
Over the Operating Range
Parameters [20]
Cypress
Alt Parameter
Parameter
SRAM Read Cycle
tACS
tACE
tRC[21]
tRC
tAA
tAA[22]
tOE
tDOE
[22]
tOHA
tOH
tLZ
tLZCE[23, 24]
tHZ
tHZCE[23, 24]
tLZOE[23, 24]
tOLZ
tOHZ
tHZOE[23, 24]
tPA
tPU[23]
tPD[23]
tPS
–
tDBE
–
tLZBE[23]
tHZBE[23]
–
SRAM Write Cycle
tWC
tWC
tPWE
tWP
tCW
tSCE
tDW
tSD
tHD
tDH
tAW
tAW
tAS
tSA
tHA
tWR
tHZWE[23, 24, 25] tWZ
tOW
tLZWE[23, 24]
tBW
–
20 ns
Description
25 ns
45 ns
Unit
Min
Max
Min
Max
Min
Max
Chip enable access time
Read cycle time
Address access time
Output enable to data valid
Output hold after address change
Chip enable to output active
Chip disable to output inactive
Output enable to output active
Output disable to output inactive
Chip enable to power active
Chip disable to power standby
Byte enable to data valid
Byte enable to output active
Byte disable to output inactive
–
20
–
–
3
3
–
0
–
0
–
–
0
–
20
–
20
10
–
–
8
–
8
–
20
10
–
8
–
25
–
–
3
3
–
0
–
0
–
–
0
–
25
–
25
12
–
–
10
–
10
–
25
12
–
10
–
45
–
–
3
3
–
0
–
0
–
–
0
–
45
–
45
20
–
–
15
–
15
–
45
20
–
15
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Write cycle time
Write pulse width
Chip enable to end of write
Data setup to end of write
Data hold after end of write
Address setup to end of write
Address setup to start of write
Address hold after end of write
Write enable to output disable
Output active after end of write
Byte enable to end of write
20
15
15
8
0
15
0
0
–
3
15
–
–
–
–
–
–
–
–
8
–
–
25
20
20
10
0
20
0
0
–
3
20
–
–
–
–
–
–
–
–
10
–
–
45
30
30
15
0
30
0
0
–
3
30
–
–
–
–
–
–
–
–
15
–
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Switching Waveforms
Figure 6. SRAM Read Cycle #1 (Address Controlled) [21, 22, 26]
tRC
Address
Address Valid
tAA
Data Output
Previous Data Valid
Output Data Valid
tOHA
Notes
20. Test conditions assume signal transition time of 3 ns or less, timing reference levels of VCC/2, input pulse levels of 0 to VCC(typ), and output loading of the specified
IOL/IOH and load capacitance shown in Figure 5 on page 10.
21. WE must be HIGH during SRAM read cycles.
22. Device is continuously selected with CE, OE and BHE / BLE LOW.
23. These parameters are guaranteed by design but not tested.
24. Measured ±200 mV from steady state output voltage.
25. If WE is LOW when CE goes LOW, the outputs remain in the high impedance state.
26. HSB must remain HIGH during read and write cycles.
Document Number: 001-49918 Rev. *M
Page 11 of 26
CY14B104LA, CY14B104NA
Switching Waveforms (continued)
Figure 7. SRAM Read Cycle #2 (CE and OE Controlled) [27, 28, 29]
Address
Address Valid
tRC
tHZCE
tACE
CE
tAA
tLZCE
tHZOE
tDOE
OE
tHZBE
tLZOE
tDBE
BHE, BLE
tLZBE
Data Output
High Impedance
Output Data Valid
tPU
ICC
tPD
Active
Standby
Figure 8. SRAM Write Cycle #1 (WE Controlled) [27, 29, 30, 31]
tWC
Address
Address Valid
tSCE
tHA
CE
tBW
BHE, BLE
tAW
tPWE
WE
tSA
tSD
Data Input
Input Data Valid
tHZWE
Data Output
tHD
Previous Data
tLZWE
High Impedance
Notes
27. BHE and BLE are applicable for × 16 configuration only.
28. WE must be HIGH during SRAM read cycles.
29. HSB must remain HIGH during read and write cycles.
30. If WE is LOW when CE goes LOW, the outputs remain in the high impedance state.
31. CE or WE must be >VIH during address transitions.
Document Number: 001-49918 Rev. *M
Page 12 of 26
CY14B104LA, CY14B104NA
Switching Waveforms (continued)
Figure 9. SRAM Write Cycle #2 (CE Controlled) [32, 33, 34, 35]
tWC
Address Valid
Address
tSA
tSCE
tHA
CE
tBW
BHE, BLE
tPWE
WE
tHD
tSD
Input Data Valid
Data Input
High Impedance
Data Output
Figure 10. SRAM Write Cycle #3 (BHE and BLE Controlled) [32, 33, 34, 35]
tWC
Address
Address Valid
tSCE
CE
tSA
tHA
tBW
BHE, BLE
tAW
tPWE
WE
tSD
Data Input
tHD
Input Data Valid
High Impedance
Data Output
Notes
32. BHE and BLE are applicable for × 16 configuration only.
33. If WE is LOW when CE goes LOW, the outputs remain in the high impedance state.
34. HSB must remain HIGH during read and write cycles.
35. CE or WE must be >VIH during address transitions.
Document Number: 001-49918 Rev. *M
Page 13 of 26
CY14B104LA, CY14B104NA
AutoStore/Power-Up RECALL
Over the Operating Range
Parameter
tHRECALL [36]
tSTORE [37]
tDELAY [38]
VSWITCH
tVCCRISE[39]
VHDIS[39]
tLZHSB[39]
tHHHD[39]
20 ns
Description
Power-Up RECALL duration
STORE cycle duration
Time allowed to complete SRAM
write cycle
Low voltage trigger level
VCC rise time
HSB output disable voltage
HSB to output active time
HSB high active time
25 ns
45 ns
Min
–
–
–
Max
20
8
20
Min
–
–
–
Max
20
8
25
Min
–
–
–
Max
20
8
25
–
150
–
–
–
2.65
–
1.9
5
500
–
150
–
–
–
2.65
–
1.9
5
500
–
150
–
–
–
2.65
–
1.9
5
500
Unit
ms
ms
ns
V
s
V
s
ns
Switching Waveforms – AutoStore/Power-up RECALL
Figure 11. AutoStore or Power-Up RECALL [40]
VCC
VSWITCH
VHDIS
t VCCRISE
tHHHD
Note
37
Note37
tSTORE
tHHHD
41
Note
tSTORE
Note
41
HSB OUT
tDELAY
tLZHSB
AutoStore
tLZHSB
tDELAY
POWERUP
RECALL
tHRECALL
tHRECALL
Read & Write
Inhibited
(RWI)
POWER-UP
RECALL
Read & Write
BROWN
OUT
AutoStore
POWER-UP
RECALL
Read & Write
POWER
DOWN
AutoStore
Notes
36. tHRECALL starts from the time VCC rises above VSWITCH.
37. If an SRAM write has not taken place since the last non-volatile cycle, no AutoStore or Hardware STORE takes place.
38. On a Hardware STORE and AutoStore initiation, SRAM write operation continues to be enabled for time tDELAY.
39. These parameters are guaranteed by design but not tested.
40. Read and write cycles are ignored during STORE, RECALL, and while VCC is below VSWITCH.
41. During power-up and power-down, HSB glitches when HSB pin is pulled up through an external resistor.
Document Number: 001-49918 Rev. *M
Page 14 of 26
CY14B104LA, CY14B104NA
Software Controlled STORE/RECALL Cycle
Over the Operating Range
Parameter [42, 43]
tRC
tSA
tCW
tHA
tRECALL
Description
Min
20
0
15
0
–
STORE/RECALL initiation cycle time
Address setup time
Clock pulse width
Address hold time
RECALL duration
20 ns
Max
–
–
–
–
200
Min
25
0
20
0
–
25 ns
Max
–
–
–
–
200
Min
45
0
30
0
–
45 ns
Max
–
–
–
–
200
Unit
ns
ns
ns
ns
s
Switching Waveforms – Software Controlled STORE/RECALL Cycle
Figure 12. CE and OE Controlled Software STORE/RECALL Cycle [43]
tRC
Address
tRC
Address #1
tSA
Address #6
tCW
tCW
CE
tHA
tSA
tHA
tHA
tHA
OE
tHHHD
HSB (STORE only)
tHZCE
tLZCE
t DELAY
44
Note
tLZHSB
High Impedance
tSTORE/tRECALL
DQ (DATA)
RWI
Figure 13. AutoStore Enable/Disable Cycle[43]
Address
tRC
tRC
Address #1
Address #6
tSA
CE
tCW
tCW
tHA
tSA
tHA
tHA
tHA
OE
tLZCE
tHZCE
tSS
44
Note
t DELAY
DQ (DATA)
RWI
Notes
42. The software sequence is clocked with CE controlled or OE controlled reads.
43. The six consecutive addresses must be read in the order listed in Table 1 on page 6. WE must be HIGH during all six consecutive cycles.
44. DQ output data at the sixth read may be invalid since the output is disabled at tDELAY time.
Document Number: 001-49918 Rev. *M
Page 15 of 26
CY14B104LA, CY14B104NA
Hardware STORE Cycle
Over the Operating Range
Parameter
20 ns
Description
25 ns
45 ns
Min
Max
Min
Max
Min
Max
20
–
25
–
25
Unit
tDHSB
HSB to output active time when write latch not set
–
ns
tPHSB
Hardware STORE pulse width
15
–
15
–
15
–
ns
tSS [45, 46]
Soft sequence processing time
–
100
–
100
–
100
s
Switching Waveforms – Hardware STORE Cycle
Figure 14. Hardware STORE Cycle [47]
Write latch set
tPHSB
HSB (IN)
tSTORE
tHHHD
tDELAY
HSB (OUT)
tLZHSB
DQ (Data Out)
RWI
Write latch not set
tPHSB
HSB pin is driven high to VCC only by Internal
100 kOhm resistor,
HSB driver is disabled
SRAM is disabled as long as HSB (IN) is driven low.
HSB (IN)
HSB (OUT)
tDELAY
tDHSB
tDHSB
RWI
Figure 15. Soft Sequence Processing [45, 46]
Soft Sequence
Command
Address
Address #1
tSA
Address #6
tCW
tSS
Soft Sequence
Command
Address #1
tSS
Address #6
tCW
CE
VCC
Notes
45. This is the amount of time it takes to take action on a soft sequence command. VCC power must remain HIGH to effectively register command.
46. Commands such as STORE and RECALL lock out I/O until operation is complete which further increases this time. See the specific command.
47. If an SRAM write has not taken place since the last non-volatile cycle, no AutoStore or Hardware STORE takes place.
Document Number: 001-49918 Rev. *M
Page 16 of 26
CY14B104LA, CY14B104NA
Truth Table For SRAM Operations
HSB should remain HIGH for SRAM Operations.
Table 2. Truth Table for × 8 Configuration
CE
Inputs/Outputs[48]
WE
OE
Mode
Power
H
X
X
High Z
Deselect/Power-down
Standby
L
H
L
Data out (DQ0–DQ7);
Read
Active
L
H
H
High Z
Output disabled
Active
L
L
X
Data in (DQ0–DQ7);
Write
Active
Table 3. Truth Table for × 16 Configuration
BHE[49]
BLE[49]
Inputs/Outputs[48]
CE
WE
OE
Mode
Power
H
X
X
X
X
High Z
Deselect/Power-down
Standby
L
X
X
H
H
High Z
Output disabled
Active
L
H
L
L
L
Data out (DQ0–DQ15)
Read
Active
L
H
L
H
L
Data out (DQ0–DQ7);
DQ8–DQ15 in High Z
Read
Active
L
H
L
L
H
Data out (DQ8–DQ15);
DQ0–DQ7 in High Z
Read
Active
L
H
H
L
L
High Z
Output disabled
Active
L
H
H
H
L
High Z
Output disabled
Active
L
H
H
L
H
High Z
Output disabled
Active
L
L
X
L
L
Data in (DQ0–DQ15)
Write
Active
L
L
X
H
L
Data in (DQ0–DQ7);
DQ8–DQ15 in High Z
Write
Active
L
L
X
L
H
Data in (DQ8–DQ15);
DQ0–DQ7 in High Z
Write
Active
Notes
48. Data DQ0–DQ7 for × 8 configuration and Data DQ0–DQ15 for × 16 configuration.
49. BHE and BLE are applicable for × 16 configuration only.
Document Number: 001-49918 Rev. *M
Page 17 of 26
CY14B104LA, CY14B104NA
Ordering Information
Speed
(ns)
20
25
45
Ordering Code
Package
Diagram
CY14B104LA-ZS20XIT
51-85087 44-pin TSOP II
CY14B104LA-ZS20XI
51-85087 44-pin TSOP II
CY14B104NA-ZS20XIT
51-85087 44-pin TSOP II
CY14B104NA-ZS20XI
51-85087 44-pin TSOP II
CY14B104NA-BA20XIT
51-85128 48-ball FBGA
CY14B104NA-BA20XI
51-85128 48-ball FBGA
CY14B104LA-ZS25XIT
51-85087 44-pin TSOP II
CY14B104LA-ZS25XI
51-85087 44-pin TSOP II
CY14B104LA-BA25XIT
51-85128 48-ball FBGA
CY14B104LA-BA25XI
51-85128 48-ball FBGA
CY14B104NA-ZS25XIT
51-85087 44-pin TSOP II
CY14B104NA-ZS25XI
51-85087 44-pin TSOP II
CY14B104NA-BA25XIT
51-85128 48-ball FBGA
CY14B104NA-BA25XI
51-85128 48-ball FBGA
CY14B104NA-BA25I
51-85128 48-ball FBGA
CY14B104NA-BA25IT
51-85128 48-ball FBGA
CY14B104NA-ZSP25XIT
51-85160 54-pin TSOP II
CY14B104NA-ZSP25XI
51-85160 54-pin TSOP II
CY14B104LA-ZS45XIT
51-85087 44-pin TSOP II
CY14B104LA-ZS45XI
51-85087 44-pin TSOP II
CY14B104LA-BA45XIT
51-85128 48-ball FBGA
CY14B104LA-BA45XI
51-85128 48-ball FBGA
CY14B104NA-ZS45XIT
51-85087 44-pin TSOP II
CY14B104NA-ZS45XI
51-85087 44-pin TSOP II
CY14B104NA-BA45XIT
51-85128 48-ball FBGA
CY14B104NA-BA45XI
51-85128 48-ball FBGA
CY14B104NA-ZSP45XIT
51-85160 54-pin TSOP II
CY14B104NA-ZSP45XI
51-85160 54-pin TSOP II
Document Number: 001-49918 Rev. *M
Package Type
Operating
Range
Industrial
Page 18 of 26
CY14B104LA, CY14B104NA
Ordering Code Definitions
CY 14 B 104 L A - ZS 20 X I T
Option:
T - Tape & Reel
Blank - Std.
X - Pb-free
Blank - Sn Pb
Die Revision:
Blank - No Rev
A - 1st Rev
Voltage:
B - 3.0 V
Temperature:
I - Industrial (–40 C to 85 C)
Package:
BA – 48-ball FBGA
ZS – 44-pin TSOP II
ZSP – 54-pin TSOP II
Data Bus:
L-×8
N - × 16
Speed:
20 - 20 ns
25 - 25 ns
45 - 45 ns
Density:
104 - 4 Mb
14 - nvSRAM
Cypress
Document Number: 001-49918 Rev. *M
Page 19 of 26
CY14B104LA, CY14B104NA
Package Diagrams
Figure 16. 44-pin TSOP II Package Outline, 51-85087
51-85087 *E
Document Number: 001-49918 Rev. *M
Page 20 of 26
CY14B104LA, CY14B104NA
Package Diagrams (continued)
Figure 17. 48-ball FBGA (6 × 10 × 1.2 mm) Package Outline, 51-85128
51-85128 *F
Document Number: 001-49918 Rev. *M
Page 21 of 26
CY14B104LA, CY14B104NA
Package Diagrams (continued)
Figure 18. 54-pin TSOP II (22.4 × 11.84 × 1.0 mm) Package Outline, 51-85160
51-85160 *D
Document Number: 001-49918 Rev. *M
Page 22 of 26
CY14B104LA, CY14B104NA
Acronyms
Acronym
Document Conventions
Description
Units of Measure
BHE
byte high enable
BLE
byte low enable
°C
degree Celsius
CE
CMOS
chip enable
Hz
hertz
complementary metal oxide semiconductor
kHz
kilohertz
EIA
electronic industries alliance
k
kilo-ohm
FBGA
fine-pitch ball grid array
MHz
megahertz
HSB
I/O
hardware store busy
A
microampere
input/output
F
microfarad
nvSRAM
non-volatile static random access memory
s
microsecond
OE
RoHS
output enable
mA
milliampere
restriction of hazardous substances
ms
millisecond
RWI
read and write inhibited
ns
nanosecond
SRAM
static random access memory

ohm
TSOP
thin small outline package
%
percent
WE
write enable
pF
picofarad
sec
second
V
volt
W
watt
Document Number: 001-49918 Rev. *M
Symbol
Unit of Measure
Page 23 of 26
CY14B104LA, CY14B104NA
Document History Page
Document Title: CY14B104LA/CY14B104NA, 4-Mbit (512 K × 8/256 K × 16) nvSRAM
Document Number: 001-49918
Rev.
ECN
Orig. of
Change
Submission
Date
**
2606696
GVCH /
PYRS
11/13/08
New data sheet.
*A
2672700
GVCH /
PYRS
03/12/09
Added best practices
Updated Ordering Information (Added CY14B104NA-BA25I).
Updated AC Switching Characteristics (Added Note 23 and referred the same
note in tLZCE, tHZCE, tLZOE, and tHZOE parameters).
*B
2710274
GVCH /
AESA
05/22/09
Moved data sheet status from Preliminary to Final.
Updated AutoStore Operation (description (Added Note)).
Updated DC Electrical Characteristics (Updated test condition for ISB
parameter, updated Note 15).
Updated AutoStore/Power-Up RECALL (Added Note 39 and referred the same
note in tVCCRISE, tLZHSB and tHHHD parameters, updated description of VHDIS
parameter).
Updated Switching Waveforms – Software Controlled STORE/RECALL Cycle
(Updated Figure 12).
*C
2738586
GVCH
07/15/09
Updated Device Operation (Updated Hardware STORE Operation
(description), updated Software STORE (description)).
Updated AutoStore/Power-Up RECALL (description of tDELAY parameter,
updated Note 38).
Updated Switching Waveforms – Software Controlled STORE/RECALL Cycle
(Added Note 44 and referred the same note in Figure 12 and Figure 13).
*D
2758397
GVCH /
AESA
09/01/09
Updated Features (Removed commercial temperature related information).
Updated Operating Range (Removed commercial temperature related
information).
Updated DC Electrical Characteristics (Removed commercial temperature
related information).
Updated Ordering Information (Updated part numbers).
*E
2773362
GVCH
10/06/09
Updated Ordering Information (Added 20 ns parts in a 48-ball FBGA package).
*F
2826364
GVCH /
PYRS
12/11/09
Updated Features (Changed STORE cycles to QuantumTrap from 200K to
1 Million).
*G
2923475
GVCH /
AESA
04/27/2010
Updated Pin Definitions (Added more clarity on HSB pin operation).
Updated Device Operation (Updated Hardware STORE Operation (added
more clarity on HSB pin operation), updated Table 1 (added more clarity on
BHE/BLE pin operation)).
Updated Switching Waveforms – AutoStore/Power-up RECALL (HSB pin
operation in Figure 11 and updated Note 41).
Updated Package Diagrams
Updated Sales, Solutions, and Legal Information.
*H
3132368
GVCH
01/10/2011
Updated Pinouts (Removed the reference of Note 5 in Figure 1).
Updated Capacitance (Included input capacitance for BHE, BLE and HSB pin,
output capacitance for HSB pin).
Updated Switching Waveforms – AutoStore/Power-up RECALL (Fixed typo
error in Figure 11).
Added Acronyms and Units of Measure.
*I
3305495
GVCH
07/07/2011
Updated DC Electrical Characteristics (Added Note 17 and referred the same
note in VCAP parameter).
Updated AC Switching Characteristics (Added Note 20 and referred the same
note in Parameters).
Updated Thermal Resistance (Values of JA for all packages).
Updated Package Diagrams.
Document Number: 001-49918 Rev. *M
Description of Change
Page 24 of 26
CY14B104LA, CY14B104NA
Document History Page (continued)
Document Title: CY14B104LA/CY14B104NA, 4-Mbit (512 K × 8/256 K × 16) nvSRAM
Document Number: 001-49918
Rev.
ECN
Orig. of
Change
Submission
Date
*J
3389991
GVCH
09/30/2011
Updated Package Diagrams.
*K
3514367
GVCH
02/01/2012
Removed Best Practices.
Updated Ordering Information (Added CY14B104NA-BA25IT).
*L
3643590
GVCH
06/13/2012
Updated DC Electrical Characteristics (Added VVCAP parameterand its details,
added Note 18 and referred the same note in VVCAP parameter).
*M
3724900
GVCH
09/03/2012
Updated Maximum Ratings (Changed “Ambient temperature with power
applied” to “Maximum junction temperature”).
Updated Package Diagrams (spec 51-85087 (Changed revision from *D to *E),
spec 51-85160 (Changed revision from *C to *D)).
Document Number: 001-49918 Rev. *M
Description of Change
Page 25 of 26
CY14B104LA, CY14B104NA
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
cypress.com/go/clocks
psoc.cypress.com/solutions
cypress.com/go/interface
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
Optical & Image Sensing
PSoC
Touch Sensing
USB Controllers
Wireless/RF
cypress.com/go/memory
cypress.com/go/image
cypress.com/go/psoc
cypress.com/go/touch
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2008-2012. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-49918 Rev. *M
Revised September 3, 2012
All products and company names mentioned in this document may be the trademarks of their respective holders.
Page 26 of 26
Similar pages