RF SWITCH CG2176X3 50Ω TERMINATION TYPE HIGH POWER Enter a Short Document/Title SPDT SWITCH Name Here DESCRIPTION PACKAGE The CG2176X3 is a pHEMT GaAs MMIC 50Ω termination type high power SPDT (Single Pole Double Throw) switch which was developed for WiMAX and WiFi. 6-pin Thin SON (XS03) Package (1.5mm x 1.5mm x 0.37mm) FEATURES Control voltage : VC(H) = 1.8 to 5.0 V (3.0V TYP.) VC(L) = -0.2 to 0.2 V (0V TYP.) Low insertion loss : Lins1 = 0.45 dB TYP. @ f = 2.3 to 2.7 GHz Lins2 = 0.50 dB TYP. @ f = 3.3 to 3.8 GHz Lins3 = 0.55 dB TYP. @ f = 4.9 to 5.85 GHz High isolation : ISL1 = 30 dB TYP. @ f = 2.3 to 2.7 GHz ISL2 = 25 dB TYP. @ f = 3.3 to 3.8 GHz ISL3 = 22 dB TYP. @ f = 4.9 to 5.85 GHz Power handling : Pin(0.5dB) = +37.5 dBm TYP. @ VC(H) = 3.0 V, VC(L) = 0 V APPLICATIONS WiMAX and wireless LAN (IEEE802.11a/b/g/n/ac) ORDERING INFORMATION Part Number Order Number CG2176X3 CG2176X3-C2 CG2176X3-EVAL CG2176X3-EVAL This document is subject to change without notice. Date Published: January 2017 CDS-0014-10 (Issue E) Package 6-pin plastic TSON (XS03) (Pb-Free) Marking C05 Description • Embossed tape 8 mm wide • Pin 1, 6 face the perforation side of the tape • MOQ 10 kpcs/reel • Evaluation Board with DC block capacitors, power supply bypass capacitors, and RF and DC connectors • MOQ 1 1 CG2176X3 PIN CONFIGURATION AND INTERNAL BLOCK DIAGRAM TRUTH TABLE VC1 VC2 RFC-RF1 RFC-RF2 High Low ON OFF Low High OFF ON ABSOLUTE MAXIMUM RATINGS (TA = +25˚C, unless otherwise specified) Parameter Symbol Control Voltage Rating Unit Note 1 V Note 2 dBm 6.0 VC +38 Input Power (ON Port, peak) Pin Input Power (ON Port, average) Pin +28 dBm Pin(off) +20 dBm Power Dissipation (average) PD 150 mW Operating Ambient Temperature TA -45～+85 ˚C Storage Temperature Tstg -55～+150 ˚C Input Power (OFF Port) Note 1. |VC1 - VC2|≦6.0V 2. 3.0V≦|VC1 - VC2|≦5.0V RECOMMENDED OPERATING RANGE (TA = +25˚C, unless otherwise specified) Parameter Symbol MIN. TYP. MAX. Unit f1 2.3 - 2.7 GHz f2 3.3 - 3.8 GHz f3 4.9 - 5.85 GHz Switch Control Voltage (H) VC(H) +1.8 +3.0 +5.0 V Switch Control Voltage (L) VC(L) -0.2 0 +0.2 V Operating Frequency This document is subject to change without notice. 2 CG2176X3 ELECTRICAL CHARACTERISTICS (TA=+25˚C, VC(H)=3.0V, VC(L)=0V, Zo=50Ω, DC Block Capacitance=8pF, unless otherwise specified) Parameter Symbol Insertion Loss Isolation (RFC – OFF Port) Isolation (RF2 – RF1) 0.5 dB Loss Compression Input Power Note MIN. TYP. MAX. Unit Lins1 f = 2.3 to 2.7 GHz - 0.45 0.60 dB Lins2 f = 3.3 to 3.8 GHz - 0.50 0.65 dB Lins3 f = 4.9 to 5.85 GHz - 0.55 0.75 dB ISL1 f = 2.3 to 2.7 GHz 27 30 - dB ISL2 f = 3.3 to 3.8 GHz 22 25 - dB ISL3 f = 4.9 to 5.85 GHz 19 22 - dB ISL4 f = 2.3 to 2.7 GHz 23 26 - dB ISL5 f = 3.3 to 3.8 GHz 20 23 - dB ISL6 f = 4.9 to 5.85 GHz 17 20 - dB RL1 f = 2.3 to 2.7 GHz 12 17 - dB RL2 f = 3.3 to 3.8 GHz 12 17 - dB RL3 f = 4.9 to 5.85 GHz 12 17 - dB URL1 f = 2.3 to 2.7 GHz 12 17 - dB URL2 f = 3.3 to 3.8 GHz 12 17 - dB URL3 f = 4.9 to 5.85 GHz 12 17 - dB Pin(0.5 dB) f = 2.3 to 2.7 GHz +35.5 +37.5 - dBm f = 3.3 to 3.8 GHz +35.5 +37.5 - dBm f = 4.9 to 5.85 GHz +35.5 +37.5 - dBm Return Loss Unused Port Return Loss Test Conditions Switch Control Current Icont RF None - 16 30 µA Switch Control Speed tsw 50% CTL to 90/10% RF - 100 250 ns Note Pin(0.5dB) is the measured input power level when the insertion loss increases 0.5dB more than that of the linear range. This document is subject to change without notice. 3 CG2176X3 EVALUATION CIRCUIT The application circuits and their parameters are for reference only and are not intended for use in actual designs. DC Blocking Capacitors are required at all RF ports. PACKAGE DIMENSIONS 6-pin Plastic TSON (XS03) (Unit: mm) This document is subject to change without notice. 4 CG2176X3 RECOMMENDED SOLDERING CONDITIONS Recommended Soldering Conditions are available on CEL’s Part Summary page under Associated Documents This document is subject to change without notice. 5 CG2176X3 REVISION HISTORY Version Change to current version Page(s) CDS-0014-09 (Issue A) February 17, 2016 CDS-0014-09 (Issue B) March 24, 2016 Initial datasheet N/A Added Eval Board ordering information Updated Marking information 1, 2 CDS-0014-10 (Issue C) March 31, 2016 Updated Max Insertion Loss f = 4.9 to 5.85 GHz, from 0.70dB to 0.75dB 3 CDS-0014-10 (Issue D) August 11, 2016 Removed “preliminary” All CDS-0014-10 (Issue E) January 11, 2017 Revised Electrical Characteristics table Added “Recommended Soldering Conditions” section 3, 5 This document is subject to change without notice. 6 CG2176X3 [CAUTION] ・ All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. ・ You should not alter, modify, copy, or otherwise misappropriate any CEL product, whether in whole or in part. ・ CEL does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of CEL products or technical information described in this document. No license, expressed, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of CEL or others. ・ Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. CEL assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. ・ CEL has used reasonable care in preparing the information included in this document, but CEL does not warrant that such information is error free. CEL assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. ・ Although CEL endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a CEL product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. ・ Please use CEL products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. CEL assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. ・ This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of CEL. ・ Please contact CEL if you have any questions regarding the information contained in this document or CEL products, or if you have any other inquiries. This document is subject to change without notice. 7 CG2176X3 [CAUTION] This product uses gallium arsenide (GaAs) of the toxic substance appointed in laws and ordinances. GaAs vapor and powder are hazardous to human health if inhaled or ingested. ・ Do not dispose in fire or break up this product. ・ Do not chemically make gas or powder with this product. ・ When discarding this product, please obey the laws of your country. ・ Do not lick the product or in any way allow it to enter the mouth. [CAUTION] Although this device is designed to be as robust as possible, ESD (Electrostatic Discharge) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. CEL Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054 • Tel: (408) 919-2500 • www.cel.com For a complete list of sales offices, representatives and distributors, Please visit our website: www.cel.com/contactus For inquiries email us at [email protected] This document is subject to change without notice. 8