Document 585-1 Shielded Power Inductors–LPS5015 Series • Very low DCR; excellent current handling • 5.0 × 5.0 mm footprint; less than 1.5 mm tall Designer’s Kit C350 contains 3 each of all values Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 102 – 107 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1000/7″reel; 3500/13″ reel Plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 1.57 mm pocket depth Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm PCB washing Only pure water or alcohol recommended DCR SRF max3 typ4 ±20% (µH) (Ohms) (MHz) Inductance2 Part number1 LPS5015-102ML_ LPS5015-132ML_ LPS5015-182ML_ LPS5015-222ML_ LPS5015-332ML_ LPS5015-472ML_ LPS5015-562ML_ LPS5015-682ML_ LPS5015-822ML_ LPS5015-103ML_ LPS5015-123ML_ LPS5015-153ML_ LPS5015-183ML_ LPS5015-223ML_ LPS5015-333ML_ LPS5015-473ML_ LPS5015-563ML_ LPS5015-683ML_ LPS5015-104ML_ LPS5015-124ML_ LPS5015-154ML_ LPS5015-224ML_ LPS5015-334ML_ LPS5015-474ML_ LPS5015-564ML_ LPS5015-684ML_ LPS5015-105ML_ LPS5015-155ML_ LPS5015-185ML_ LPS5015-225ML_ LPS5015-335ML_ LPS5015-475ML_ 1.0 1.3 1.8 2.2 3.3 4.7 5.6 6.8 8.2 10 12 15 18 22 33 47 56 68 100 120 150 220 330 470 560 680 1000 1500 1800 2200 3300 4700 0.050 0.065 0.075 0.090 0.125 0.150 0.175 0.225 0.280 0.300 0.350 0.360 0.550 0.675 0.750 1.00 1.13 1.45 1.95 2.50 3.40 4.50 7.40 7.50 8.50 10.6 15.0 25.0 28.0 36.0 55.0 80.0 183 150 128 116 88 73 67 57 49 44 40 38 35 31 24 18 17 15 12 10 9.3 7.3 5.7 4.9 4.3 4.0 3.2 2.5 2.2 2.1 1.7 1.4 Isat (A)5 10% 20% 30% drop drop drop Irms (A)6 20°C 40°C rise rise 3.6 2.5 2.6 2.4 1.9 1.6 1.6 1.3 1.3 1.2 1.0 0.80 0.75 0.70 0.55 0.46 0.40 0.33 0.30 0.25 0.23 0.20 0.15 0.12 0.10 0.10 0.080 0.080 0.078 0.072 0.064 0.062 1.90 1.70 1.50 1.40 1.30 1.20 1.10 0.90 0.85 0.80 0.75 0.73 0.70 0.60 0.50 0.45 0.40 0.35 0.30 0.27 0.25 0.22 0.17 0.16 0.14 0.13 0.10 0.090 0.085 0.065 0.055 0.045 3.8 2.6 2.8 2.6 2.0 1.7 1.6 1.4 1.3 1.3 1.1 0.84 0.77 0.73 0.59 0.48 0.43 0.38 0.33 0.28 0.25 0.21 0.17 0.12 0.11 0.11 0.090 0.086 0.083 0.078 0.072 0.069 3.9 2.8 2.9 2.7 2.0 1.8 1.6 1.5 1.4 1.3 1.2 0.86 0.80 0.75 0.60 0.49 0.45 0.39 0.34 0.30 0.26 0.22 0.18 0.13 0.12 0.11 0.093 0.088 0.086 0.080 0.076 0.072 2.65 2.35 2.15 2.00 1.80 1.62 1.45 1.25 1.05 0.95 0.84 0.84 0.83 0.82 0.70 0.57 0.52 0.47 0.42 0.37 0.33 0.29 0.22 0.21 0.190 0.175 0.150 0.140 0.130 0.090 0.075 0.065 1. Please specify termination and packaging codes: LPS5015-335MLC Termination: L = RoHS compliant silver-palladiumplatinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C= 7″ machine-ready reel. EIA-481 embossed plastic tape 1000 parts per full reel). B= Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D= 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (3500 parts per full reel). 2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4192A. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using Agilent/HP 8753ES or equivalent. 5. DC current that causes the specified inductance drop from its value without current. 6. Current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Document 585-1 Revised 12/05/08 Document 585-2 Shielded SMT Power Inductors – LPS5015 Series Typical L vs Frequency Typical L vs Current 10000 10000 3300 µH 3300 µH 1000 µH 330 µH 100 µH 100 33 µH 10 µH 10 1000 µH 1000 Inductance (µH) Inductance (µH) 1000 330 µH 100 µH 100 33 µH 10 µH 10 3.3 µH 3.3 µH 1 1 0.01 1 0.1 10 0.01 1 0.1 Frequency (MHz) 10 Current (A) Typical Current Derating 0.189 ±0.003* 4,80 ±0,076 0.189 ±0.003* 4,80 ±0,076 100 XXX X 90 80 70 Dash number 60 Winding direction Internal code Recommended Land Pattern 50 0.0551 ±0.004 1,4 ±0,1 40 30 20 25°C Percent of rated current 120 110 Isat Irms 10 0 -40 -20 0 20 0.138 3,50 0.090 2,30 0.060 1,50 40 60 80 100 45° typ 120 140 Ambient temperature (°C) 0.039 typ 1,00 0.039 typ 1,00 are of the case not * Dimensions including the termination. For maximum overall dimensions including the termination, add 0.005 in / 0,13 mm. Dimensions are in 0.060 1,50 0.134 3,40 0.197 5,00 inches mm Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 0.197 5,00 0.134 0.090 3,40 2,30 Document 585-2 Revised 12/05/08