HMC682LP6C / 682LP6CE v00.0308 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 1.7 - 2.2 GHz mixers - Downconverters - SMT 9 Typical Applications Features The HMC682LP6C(E) is Ideal for: High Input IP3: +25 dBm • Cellular/3G & LTE/WiMAX/4G Conversion Gain: 6 dB • Basestations & Repeaters Low LO Drive: 0 dBm • GSM, CDMA & OFDM High Channel Isolation • Dual Density Receivers 40 Lead 6x6mm SMT Package: 36mm2 Functional Diagram General Description The HMC682LP6C(E) is a high linearity, dual channel downconverter with integrated LO amplifier in a 6x6 SMT QFN package covering 1.7 - 2.2 GHz. Excellent input IP3 performance of +25 dBm for down conversion is provided for 3G & 4G GSM/CDMA applications at an LO drive of 0 dBm. With an input 1 dB compression of +15 dBm, the RF port will accept a wide range of input signal levels. Conversion gain is 6 dB typical. The 60 - 400 MHz IF frequency response will satisfy various GSM/CDMA receive frequency plans. Electrical Specifications, TA = +25 °C, IF = 200 MHz, LO = 0 dBm Vcc1, 2 = Vcc_BAL1, 2 = Vcc_AMP1, 2 [1] = Vcc_IF1P, N = Vcc_IF2P, N = +5V, BIAS1, 2 = +2.5V Parameter Min. Frequency Range, RF Typ. Units GHz Frequency Range, LO 1.4 - 2.0 GHz Frequency Range, IF 0.06 - 0.40 GHz Conversion Gain 4 6 12 dB 17 25 dB Noise Figure (SSB) LO to RF Isolation dB LO to IF Isolation 15 22 dB RF to IF Isolation 15 30 dB IP3 (Input) 25 dBm 1 dB Compression (Input) 15 dBm Channel to Channel Isolation 55 dB LO Drive Input Level (Typical) -3 to +3 Supply Current (Icc) [1] See application circuit 9-1 Max. 1.7 - 2.2 450 dBm 550 mA [2] Unless otherwise noted all measurements with low side LO & IF = 200 MHz. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC682LP6C / 682LP6CE v00.0308 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 1.7 - 2.2 GHz Single Channel: Isolation -20 8 6 4 +25 C +85 C -40 C 2 0 1.6 1.7 1.8 1.9 2 -25 -30 -35 RF/IF LO/RF LO/IF -40 2.1 2.2 -45 1.5 2.3 1.6 1.7 FREQUENCY (GHz) 1.8 1.9 2 2.1 2.2 2.3 FREQUENCY (GHz) Single Channel: Conversation Gain vs. LO Drive Single Channel: Return Loss 10 0 RF1 LO1 LO_SEL 0V LO1 LO_SEL +5V -5 8 RETURN LOSS (dB) CONVERSION GAIN (dB) 9 -15 ISOLATION (dB) CONVERSION GAIN (dB) 10 6 -3 dBm 0 dBm +3 dBm 4 2 -10 -15 -20 -25 0 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 -30 1.3 2.3 1.4 1.5 1.6 FREQUENCY (GHz) 1.7 1.8 1.9 2 2.1 2.2 2.3 FREQUENCY (GHz) mixers - Downconverters - SMT Single Channel: Conversion Gain vs. Temperature Single Channel: Input P1dB vs. Temperature Single Channel: IF Bandwidth 10 20 15 IF Return Loss Conversion Gain 0 P1dB (dBm) RESPONSE (dB) 5 -5 +25 C +85 C -40 C 10 -10 5 -15 -20 0 0.1 0.2 0.3 FREQUENCY (GHz) 0.4 0.5 0 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9-2 HMC682LP6C / 682LP6CE v00.0308 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 1.7 - 2.2 GHz 30 25 25 20 20 IP3 (dBm) IP3 (dBm) Single Channel: Input IP3 vs. Temperature 30 -3 dBm 0 dBm +3 dBm 15 10 5 5 1.7 1.8 1.9 2 2.1 2.2 0 1.6 2.3 +25 C +85 C -40 C 15 10 0 1.6 1.7 1.8 FREQUENCY (GHz) 1.9 2 2.1 2.2 2.3 FREQUENCY (GHz) Dual Channel: Channel to Channel Isolation[1] Dual Channel: LO1 to LO2 Isolation[2] -20 -10 -20 -30 RF1 TO RF2 AT IFI RF2 TO RF1 AT IF2 ISOLATION (dBc) ISOLATION (dBc) mixers - Downconverters - SMT 9 Single Channel: Input IP3 vs. LO Drive -40 -30 -40 -50 -50 -60 -60 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 FREQUENCY (GHz) -70 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 FREQUENCY (GHz) Noise Figure vs. Temperature [1] For 1900 MHz, RF1 = 1900 MHz @ 0 dBm, RF2 = 1901 MHz @ 0 dBm, LO = 1700 MHz @ 0 dBm, IF2 terminated with 50 Ohms. Channel isolation is the dBc difference at IF1 port between the fundamental tone @ 200 MHz and the leakage tone at 201 MHz. 16 NOISE FIGURE (dB) 15 +25 C +85 C -40 C 14 13 [2] For 1900 MHz, LO1 = 1700 MHz @ 0 dBm, LO2 = 1699 MHz @ 0 dBm, LO1 is selected, RF1 = RF2 = 1900 MHZ @ 0 dBm, IF2 terminated with 50 Ohms. LO1-LO2 isolation is the dBc difference measured at the IF1 port between the fundamental tone at 200 MHz and the leakage tone at 201 MHz. 12 11 10 9 8 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 FREQUENCY (GHz) 9-3 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC682LP6C / 682LP6CE v00.0308 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 1.7 - 2.2 GHz +2RF -2LO Response vs. LO Drive [3] 70 60 +25 C +85 C -40 C 50 40 1.6 1.7 1.8 1.9 2 2.1 2.2 70 60 40 1.6 2.3 -3 dBm 0 dBm +3 dBm 50 1.7 1.8 FREQUENCY (GHz) 2 2.1 2.2 2.3 +3RF -3LO Response vs. LO Drive [3] 90 +3RF-3LO RESPONSE (dBc) 90 +3RF-3LO RESPONSE (dBc) 1.9 FREQUENCY (GHz) +3RF -3LO Response vs. Temperature [3] 85 80 75 +25 C +85 C -40 C 70 65 1.6 9 80 +2RF-2LO RESPONSE (dBc) +2RF-2LO RESPONSE (dBc) 80 1.7 1.8 1.9 2 2.1 FREQUENCY (GHz) 2.2 2.3 85 80 75 -3 dBm 0 dBm +3 dBm 70 65 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 FREQUENCY (GHz) mixers - Downconverters - SMT +2RF -2LO Response vs. Temperature [3] [3] Refernced to RF input power @ 0 dBm For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9-4 HMC682LP6C / 682LP6CE v00.0308 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 1.7 - 2.2 GHz mixers - Downconverters - SMT 9 9-5 MxN Spurious @ IF Port Harmonics of LO nLO nLO Spur @ RF Port LO Freq. (GHz) 1 2 3 4 mRF 0 1 2 3 4 1.4 25 29 38 19 0 xx 39 20 46 47 1.5 24 28 31 21 1 35 0 40 24 66 1.6 25 23 30 21 2 72 61 63 54 83 3 107 73 90 70 101 4 116 125 114 106 108 1.7 26 19 38 14 1.8 29 16 43 16 1.9 31 15 40 19 2.0 32 14 43 22 RF Freq. = 1.9 GHz @ -5 dBm LO Freq. = 1.7 GHz @ 0 dBm All values in dBc below IF power level (1RF - 1LO). LO = 0 dBm All values in dBc below input LO level measured at RF port. Typical Supply Current vs. Vdd Truth Table Vcc Icc (mA) LO_SEL (V) 4.75 415 0 LO Signal Path LO1 5.00 450 5 LO2 5.25 490 Downconverter will operate over full voltage range shown above. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC682LP6C / 682LP6CE v00.0308 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 1.7 - 2.2 GHz Absolute Maximum Ratings +15 dBm LO Drive (Vcc= +5V) +6 dBm Vcc (LO or IF) 5.5V Channel Temperature 12.5°C Continuous Pdiss (T = 85°C) (derate 110.53 mW/°C above 85°C) 4.42 W Thermal Resistance (channel to ground paddle) 9.05 °C/W Storage Temperature -65 to 150°C Operating Temperature -40 to +85 °C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 9 mixers - Downconverters - SMT RF / IF Input (Vcc= +5V) Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC682LP6C Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] HMC682LP6CE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] Package Marking [3] H682 XXXX H682 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9-6 HMC682LP6C / 682LP6CE v00.0308 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 1.7 - 2.2 GHz mixers - Downconverters - SMT 9 Pin Descriptions Pin Number Function Description 1, 10 RF1, RF2 These are the RF inputs of the mixers. See application circuit for the off-chip matching components 2, 9 TAP1, TAP2 These are the center taps of the internal RF baluns. Connect these pins to the AC ground via external capacitors. See application circuit. 3, 5, 8, 15, 16, 22, 23, 26 - 29, 36, 35 GND These pins must be connected to RF ground. 4, 7 BIAS1, BIAS2 Bias pins for mixer cores. See application circuit for the nominal value. 6, 17, 18, 24, 33, 34 Vcc1, Vcc_BAL2, Vcc_AMP2, Vcc2, Vcc_AMP1, Vcc_BAL1 Power supply voltage pins. See application circuit for required external components. 11, 20, 31, 40 N/C No Connection required. These pins may be connected to RF GND without affecting performance. 12, 39 IND1, IND2 Current source inductors for IF amplifiers. 13, 14, 38, 37 IF2P, IF2N, IF1P, IF1N Differential IF outputs and DC BIAS for IF Amps. 19, 32 BIAS_ADJ1, BIAS_ADJ2 Adjusts LO buffer amplifies current via external resistor. See application circuit. 21, 30 LO2, LO1 These are LO inputs of the mixers. See application circuit for off-chip matching components. LO_SEL Control voltage for LO1 or LO2 selection. LO1 is selected when LO SEL is set low. LO2 is selected when LO SEL is set high. See application circuit and truth table for low and high voltage levels. 25 9-7 Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC682LP6C / 682LP6CE v00.0308 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 1.7 - 2.2 GHz 9 mixers - Downconverters - SMT Evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9-8 HMC682LP6C / 682LP6CE v00.0308 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 1.7 - 2.2 GHz mixers - Downconverters - SMT 9 9-9 List of Materials for Evaluation PCB 119925 [1] Item Description J1 - J6 PCB Mount SMA Connector J7 - J10 2mm Vertical Molex 8pc Connector L1, L2 51 nH Inductor, 0603 Pkg. L3 - L6 390 nH Inductor, 0603 Pkg. L7 - L10 2.2 nH Inductor, 0402 Pkg. C7, C8, C26, C38 22 pF Capacitor, 0402 Pkg. C9, C10 10 nF Capacitor, 0603 Pkg. C11, C17, C19, C24, C27, C29, C34, C37, C40, C48, C50 1 nF Capacitor, 0402 Pkg. C12, C15, C16, C18, C20, C25, C28, C30, C35, C36, C39, C47, C49 0.1 µF Capacitor, 0603 Pkg. C13, C14, C60 - C63 100 pF Capacitor, 0402 Pkg. C21, C22, C32, C33 0.01 µF Capacitor, 0402 Pkg. C51 - C59 0.47 µF Capacitor, 0603 Pkg. R7, R8 330 Ohm Resistor, 0603 Pkg. T1, T2 1:1 Transformer - Tyco ETC1-1T U1 HMC682LP6C(E) PCB [2] 118274 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon-25FR and FR4 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC682LP6C / 682LP6CE v00.0308 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 1.7 - 2.2 GHz 9 mixers - Downconverters - SMT Application Circuit For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9 - 10