TDK NL453232T-100J-PF Inductors for standard circuits wound ferrite Datasheet

I
N
D
U
C
T
O
R
S
January 2015
Inductors for Standard Circuits
Wound Ferrite
NL Series
NL453232 Type
NL453232
4532 [1812 inch]*
* Dimensions Code JIS[EIA]
(2/9)
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
20150105 / inductor_commercial_standard_nl453232_en.fm
(3/9)
I
N
D
U
C
T
O
R
S
Inductors for Standard Circuits
Product compatible with RoHS directive
Compatible with lead-free solders
Wound Ferrite
Overview of NL453232 Type
FEATURES
Resin mold type wound inductor for standard circuits.
E-12 Series, wide lineup compatible with J (±5%) tolerance, can be used for applications that need to meet strict L tolerance such as
filter circuits.
Has excellent inductance temperature characteristics in the operating temperature range.
APPLICATION
Smart meters, AV equipment, xDSL, electronic devices for communications infrastructure such as mobile base stations, industrial
equipment, other
PART NUMBER CONSTRUCTION
NL
Series name
453232
L×W×H Dimensions
(mm)
453232
4.5×3.2×3.2
T
Packaging style
T
Taping
-
1R0
J
Inductance
(μH)
1R0
1
100
10
101
100
102
1000
Inductance
tolerance
J
±5%
-
PF
Internal code
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Package quantity
Operating
Storage
Type
temperature
temperature
(pieces/reel)
(°C)
(°C)
NL453232
–40 to +105
–40 to +105
500
Operating temperature range includes self-temperature rise.
The Storage temperature range is for after the circuit board is mounted.
Individual weight
(mg)
180
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150105 / inductor_commercial_standard_nl453232_en.fm
(4/9)
I
N
D
U
C
T
O
R
S
NL453232 Type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1
t1
t2
t: Time
Preheating
Temp.
T1
T2
150°C
180°C
Time
t1
90 to 120s
Soldering
Temp.
Time
T3
t2
230°C
40s
Peak
Temp.
T4
255°C
Time
t3
10s max.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150105 / inductor_commercial_standard_nl453232_en.fm
(5/9)
I
N
D
U
C
T
O
R
S
NL453232 Type
SHAPE & DIMENSIONS
4.5±0.3
102J
2.6±0.1
3.2±0.2
R0.2
C0.5
(0.6)
(3.3)
(0.6)
3.2±0.2
0.5
Dimensions in mm
2.8
RECOMMENDED LAND PATTERN
1.5
3
1.5
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150105 / inductor_commercial_standard_nl453232_en.fm
(6/9)
I
N
D
U
C
T
O
R
S
NL453232 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
L
(μH)
1
1.2
1.5
1.8
2.2
2.7
3.3
3.9
4.7
5.6
6.8
8.2
10
12
15
18
22
27
33
39
47
56
68
82
100
120
150
180
220
270
330
390
470
560
680
820
1000
Tolerance
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
Q
L, Q measuring
frequency
Self-resonant
frequency
DC resistance
Rated current
Part No.
min.
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
40
40
40
40
40
40
40
40
40
30
30
30
30
(MHz)
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.252
(MHz)min.
100
80
70
60
55
50
45
40
35
33
27
25
20
18
17
15
13
12
11
10
10
9
9
8
8
6
5
5
4
4
3.5
3
3
3
3
2.5
2.5
(ȍ )max.
0.5
0.55
0.6
0.65
0.7
0.75
0.8
0.9
1
1.1
1.2
1.4
1.6
2
2.5
2.8
3.2
3.6
4
4.5
5
5.5
6
7
8
8
9
9.5
10
12
14
16
26
30
30
35
40
(mA)max.
450
430
410
390
380
370
355
330
315
300
285
270
250
225
200
190
180
170
160
150
140
135
130
120
110
110
105
102
100
92
85
80
62
50
50
30
30
NL453232T-1R0J-PF
NL453232T-1R2J-PF
NL453232T-1R5J-PF
NL453232T-1R8J-PF
NL453232T-2R2J-PF
NL453232T-2R7J-PF
NL453232T-3R3J-PF
NL453232T-3R9J-PF
NL453232T-4R7J-PF
NL453232T-5R6J-PF
NL453232T-6R8J-PF
NL453232T-8R2J-PF
NL453232T-100J-PF
NL453232T-120J-PF
NL453232T-150J-PF
NL453232T-180J-PF
NL453232T-220J-PF
NL453232T-270J-PF
NL453232T-330J-PF
NL453232T-390J-PF
NL453232T-470J-PF
NL453232T-560J-PF
NL453232T-680J-PF
NL453232T-820J-PF
NL453232T-101J-PF
NL453232T-121J-PF
NL453232T-151J-PF
NL453232T-181J-PF
NL453232T-221J-PF
NL453232T-271J-PF
NL453232T-331J-PF
NL453232T-391J-PF
NL453232T-471J-PF
NL453232T-561J-PF
NL453232T-681J-PF
NL453232T-821J-PF
NL453232T-102J-PF
Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (10% below the initial value)
Idc2: When based on the temperature increase (Temperature increase of 20°C by self heating)
○ Measurement equipment
Measurement item
Product No.
L, Q
4194A
Self-resonant frequency
8753C
DC resistance
VP-2941A
* Equivalent measurement equipment may be used.
Manufacturer
Agilent Technologies
Agilent Technologies
Panasonic
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150105 / inductor_commercial_standard_nl453232_en.fm
(7/9)
I
N
D
U
C
T
O
R
S
NL453232 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
100000
102J
10000
821J
681J
561J
471J
391J
121J
331J
271J
221J
181J 820J
680J
151J
101J
1000
470J
8R2J
Inductance(μH)
390J
330J
270J
220J
180J
150J
120J
100
100J
560J
6R8J
5R6J
4R7J
3R9J
3R3J
10
2R7J
2R2J
1R8J
1R5J
1R2J
1R0J
1
0.1
0.01
0.1
1.0
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
4294A
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150105 / inductor_commercial_standard_nl453232_en.fm
(8/9)
I
N
D
U
C
T
O
R
S
NL453232 Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH
100
90
1R5J
1R0J
2R2J
80
4R7J
1R2J
5R6J
2R7J
470J
70
560J
6R8J
3R3J
120J
60
8R2J
680J
Q
331J
50
100J
150J
271J
40
471J
221J
820J
220J
101J
330J
30
391J
270J
20
681J
390J
121J
3R9J
821J
1R8J
10
181J
151J
0
0.01
180J
102J
561J
0.1
1.0
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
4294A
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150105 / inductor_commercial_standard_nl453232_en.fm
(9/9)
I
N
D
U
C
T
O
R
S
NL453232 Type
PACKAGING STYLE
REEL DIMENSIONS
2.0±0.5
E
Type
NL453232
A
ø180
W1
13
W2
17
N
ø60
E
0.5
N
* These values are typical values.
(1.0)
ø13.0±0.5
W1
ø21.0±0.8
W2
A
Dimensions in mm
TAPE DIMENSIONS
P2
P0
K
P1
A
Type
NL453232
A
3.6
B
4.9
øD0
1.5+0.1/-0
B
W
F
E
øD0
t
Dimensions in mm
E
F
P0
P1
P2
W
1.75±0.1 5.50±0.05 4.00±0.10 8.00±0.10 2.00±0.05 12.0±0.30
K
3.2
t
0.4
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150105 / inductor_commercial_standard_nl453232_en.fm
Similar pages