FTR-K1 SERIES POWER RELAY 1 POLE - 6A Slim Type (Medium Load Control) FTR-LY Series n FEATURES Slim 15.0mm (h) x 5.0 mm (w) x 28.0mm (l) 1 form C and right angle type available 2 l Mounting space: 140mm , weight: 5.0g l High insulation in small package Insulation distance (between coil and contacts): 8mm (creepage/clearance) Dielectric strength: 4,000 VAC Surge strength: 6,000V l Plastic sealed type RTIII l UL, CSA, VDE, SEMKO, FIMKO, DEMKO, NEMKO compliance l Socket type available l RoHS compliant Please see page 7 for more information l l n PARTNUMBER INFORMATION [Example] (a) FTR-LY (a) A (b) Relay type (b) Contact configuration (c) Coil type A (c) 005 Y - SK (d) (e) (f ) FTR-LY : FTR-LY-Series A C P R : 1 form A : 1 form C : 1 form A (right angle type) : 1 form C (right angle type) A : Standard type (170mW) (d) Coil rated voltage 005 : 5.....60 VDC Coil rating table at page 3 (e) Contact material E Y V : AgNi : AgSnO2 : AgSnO2 + Au (0.3µm) Nil SK : PCB mounting type : Socket mounting type (only contact configuration A and C (f) Special type Actual marking does not carry the type name : "FTR" and "SK" E.g.: Ordering code: FTR-LYAA005Y-SK Actual marking: LYAA005Y 1 FTR-K1 SERIES FTR-LY SERIES n SPECIFICATION Item Contact Data Life Coil Data Timing Data Insulation LY (C,R) A ( ) (Y,E,V) LY (A,P) A ( ) (Y,E,V) Configuration 1 form C (SPDT) 1 form A (SPST-NO) Construction Single Material Y: AgSnO2 / E: AgNi / V: AgSnO2 + Au 0.3μm Resistance (initial) Y, E: Max. 100 mΩ at 6 VDC, 1 A V: Max. 30 mΩ at 6 VDC, 1A Contact rating 6A, 250VAC / 24VDC Max. carrying current 6A Max. switching voltage 250VAC Max. switching power 1,500VA / 144W Min. switching load * Y, E: 100 mA 5 VDC V: 10mA 5 VDC Mechanical Min. 10 x 106 operations Electrical Min. 50 x 103 operations (N.O.) Min. 30 x 103 operations (N.C.) at 6A, 250VAC / 30VDC resistive Rated power 170 to 217 mW Operate power 74 to 76 mW Operating temperature range -40 °C to +85 °C (no frost) Operate (at nominal voltage) Max. 8ms (no diode, without bounce) Release (at nominal voltage) Max. 4ms (no diode, without bounce) Resistance (initial) Min. 1,000MΩ at 500VDC Dielectric strength Surge strength 1,000VAC (50/60Hz) 1min.,10mA detection current Contacts to coil 4,000VAC (50/60Hz) 1min.,10mA detection current Coil to contacts 6,000V / 1.2 x 50µs standard wave Clearance 8 mm Creepage 8 mm EN61810-1, VDE0435 Other Open contacts Vibration resistance Shock Voltage 250V Pollution degree 3 Material group III a Category C / 250V Misoperation 10 to 55Hz double amplitude 1.0mm Endurance 10 to 55Hz double amplitude 1.5mm Misoperation Min. 50m/s² (11 ± 1ms) Endurance Min. 1,000m/s² (6 ± 1ms) Weight Approximately 5 g Sealing Plastic sealed RTIII Min. 100m/s² (11 ± 1ms) * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1 SERIES FTR-LY SERIES n COIL RATING Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must ReleaseVoltage (VDC) * Max. Coil Voltage (VDC) 005 5 147 3.3 0.25 11.5 006 6 211 4 0.3 13.8 009 9 476 5.9 0.45 20.7 012 12 847 7.9 0.6 27.6 018 18 1,910 11.9 0.9 41.4 024 24 3,390 15.9 1.2 55.2 048 48 10,600 31.7 2.4 110.4 217 060 60 20,570 39.6 3 138 175 Rated Power (mW) 170 Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) E63614 5A, 277 VAC (resistive) 5A, 30 VDC (resistive) 1/10 HP, 277VAC /125VAC Pilot duty: D300, C300, R300, B300 CSA C22.2 No. 14 LR 40304 VDE 40006591 EN 61810-1 (VDE 0435-Part 201) 2004-07 250VAC; 6A / 30VDC; 6A : - 10K ops. FTR-LY(A;P)A...(E;Y;V) -40 °C to +85 °C - 5K ops. FTR-LY(C;R)A...(E;Y;V) -40 °C to +85 °C EN 60730-1 (VDE 0631-Part 1) 250VAC; 6(1,5)A, 30K ops. : FTR-LY(A;P)A...(Y;V) +85 °C 250VAC; 3(1,5)A, 100K ops. : FTR-LY(A;P)A...(Y;V) +85 °C EN 61984 (VDE 0627) EN 60335-1 (VDE 0700-Part 1) - 3 FTR-K1 SERIES FTR-LY SERIES n CHARACTERISTIC DATA 4 FTR-K1 SERIES FTR-LY SERIES n DIMENSIONS Straight terminal type l Dimensions l Schematics l PC board mounting hole layout (BOTTOM VIEW) l Schematics l PC board mounting hole layout (BOTTOM VIEW) Right angle type l Dimensions Unit: mm * This terminal is not applicable for 1 form A type. 5 FTR-K1 SERIES FTR-LY SERIES Socket type l Dimensions l Schematics l PC board mounting hole layout (BOTTOM VIEW) JM-6N l Dimensions l Schematics 6 FTR-K1 SERIES FTR-LY SERIES RoHS Compliance and Lead Free Information 1. General Information l l l l All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: Duration: maximum 360˚C maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 7 FTR-K1 SERIES FTR-LY SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] Web: http://www.fujitsu.com/sg/services/micro/components/ ©2011 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. June 08, 2011 8