HER801 THRU HER806 8.0 AMP HIGH EFFICIENCY RECTIFIERS VOLTAGE RANGE 50 to 600 Volts CURRENT 8.0 Ampere FEATURES * Low forward voltage drop * High current capability * High reliability * High surge current capability * High speed switching TO-220AC .108 (2.75) MECHANICAL DATA 3.8 φ +.2 HOLE THRU .412 (10.5) MAX. .248 (6.3) .040 (1.0) MAX. * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Lead solderable per MIL-STD-202, method 208 guranteed * Polarity: As Marked * Mounting position: Any PIN 1 * Both normal and Pb free product are available: * Normal:80~95%Sn,5~20%Pb * Pb free:99 Sn above can meet Rohs enviroment substance directive request .050 (1.27) .595 (15.1) MAX. .550 (14.0) .158 (4.0) MIN. MAX. .051 MAX. (1.3) .040 MAX. (1.0) * Weight: 2.24 grams .180 (4.6) + .200 (5.08) .120 (3.05) PIN 1 + + CASE PIN 2 Case Negative Suffix "R" CASE PIN 2 Case Positive Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current HER801 HER802 50 35 50 100 70 100 HER803 HER804 HER805 300 210 300 400 280 400 200 140 200 .375"(9.5mm) Lead Length at Tc=75 C Peak Forward Surge Current, 8.3 ms single half sine-wave HER806 UNITS 600 420 600 A 8.0 150 superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 8.0A Maximum DC Reverse Current Tc=25 C 1.0 1.3 1.85 10.0 at Rated DC Blocking Voltage Tc=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG 200 60 100 -55 NOTES: 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 74 65 +150 V V V A V µA µA nS pF C RATING AND CHARACTERISTIC CURVES (HER801 THRU HER807) FIG.1-TYPICAL FORWARD FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE CHARACTERISTICS AVERAGE FORWARD CURRENT,(A) 06 HE R8 HE R8 R8 04 01 -8 05 03 -8 10.0 HE 1.0 12 10 8 6 Single Phase Half Wave 60Hz 4 Resistive Or Inductive Load 2 0 20 40 Tj=25 C 60 80 100 120 140 160 180 200 CASE TEMPERATURE ( C) Pulse Width 300us 1% Duty Cycle .1 .01 .2 .4 .6 .8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE,(V) FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50Ω NONINDUCTIVE 10Ω NONINDUCTIVE ( ) (+) D.U.T. 25Vdc (approx.) PULSE GENERATOR (NOTE 2) ( ) 1Ω NONINDUCTIVE OSCILLISCOPE (NOTE 1) PEAK FORWAARD SURGE CURRENT,(A) FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 150 120 90 Sine Wave 60 JEDEC method 30 0 1 | | | | | | | | 0 -0.25A 1cm 100 175 150 125 100 75 50 25 0 -1.0A 50 10 FIG.5-TYPICAL JUNCTION CAPACITANCE 2. Rise Time= 10ns max., Source Impedance= 50 ohms. +0.5A 5 NUMBER OF CYCLES AT 60Hz NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. trr 8.3ms Single Half Tj=25 C (+) JUNCTION CAPACITANCE,(pF) INSTANTANEOUS FORWARD CURRENT,(A) 100 0.1 SET TIME BASE FOR 0.5 1 2 5 10 20 REVERSE VOLTAGE,(V) 50 / 10ns / cm 75 50 100 200 500 1000