HCE Series Miniature amplified pressure sensors FEATURES · 10 mbar to 5 bar, absolute, gage or differential pressure · Barometric pressure ranges · Digital SPI bus and analog output · Precision ASIC signal conditioning · Calibrated and temperature compensated · Matched pressure port volumes · Miniature SMD housings · RoHS compliant · Sensortechnics PRO services ELECTRICAL CONNECTION SPECIFICATIONS Maximum ratings Supply voltage VS HCE...3 HCE...5 Output current Sink Source 2.7 ... 3.3 VDC 4.5 V ... 5.5 VDC max. 6.50 VDC 1 mA 1 mA Lead specifications Average preheating temperature gradient 2.5 K/s Soak time ca. 3 min Time above 217°C 50 s Time above 230°C 40 s Time above 250°C 15 s Peak temperature 260°C Cooling temperature gradient -3.5 K/s Temperature ranges6 Compensated Operating Storage 0 ... 85°C -25 ... 85°C -40 ... 125°C Humidity limits (non-condensing) 0 ... 95 %RH E / 11652 / A +Vs 1 Vout 4 5 6 8 3 2 Note: MISO CLK SS MOSI GND Connections for digital SPI bus (pins 4 to 6) are only available for SMD package styles (E, H and Q housings). 1/11 www.sensortechnics.com HCE Series Miniature amplified pressure sensors PRESSURE SENSOR CHARACTERISTICS (TA = 25 °C) Part no. Operating pressure Proof pressure3,5 Burst pressure4,5 HCEM010...B... HCEM020...B... HCEM050...B... HCEM100...B... HCEM200...B... HCEM500...B... HCEB001...B... HCEM010...U... HCEM020...U... HCEM050...U... HCEM100...U... HCEM200...U... HCEM500...U... HCEB001...U... HCEB002...U... HCEB005...U... HCE0611AR... HCE0811AR... 0...±10 mbar 0...±20 mbar 0...±50 mbar 0...±100 mbar 0...±200 mbar 0...±500 mbar 0...±1 bar 0...10 mbar 0...20 mbar 0...50 mbar 0...100 mbar 0...200 mbar 0...500 mbar 0...1 bar 0...2 bar 0...5 bar 600...1100 mbar(a) 800...1100 mbar(a) 250 mbar 500 mbar 750 mbar 1.2 bar 2 bar 2 bar 3 bar 250 mbar 500 mbar 750 mbar 1.2 bar 2 bar 2 bar 3 bar 6 bar 7 bar 3 bar 3 bar 500 mbar 750 mbar 1.2 bar 2 bar 2 bar 2 bar 5 bar 500 mbar 750 mbar 1.2 bar 2 bar 2 bar 2 bar 5 bar 7 bar 7 bar 5 bar 5 bar Other pressure ranges are available on request. Please contact Sensortechnics. Specification notes: 1. Total accuracy is the combined error from offset and span calibration, linearity, pressure hysteresis, and temperature effects. Linearity is the measured deviation based on a straight line. Hysteresis is the maximum output difference at any point within the operating pressure range for increasing and decreasing pressure. Calibration errors include the deviation of offset and full scale from nominal values. 2. Full Scale Span (FSS) is the algebraic difference between the output signal for the highest and lowest specified pressure. 3. Proof pressure is the maximum pressure which may be applied without causing durable shifts of the electrical parameters of the sensing element. 4. Burst pressure is the maximum pressure which may be applied without causing damage to the sensing element or leaks to the housing. 5. The HCE common mode pressure is 2 bar for all devices up to 500 mbar and 7 bar for all other devices. Common mode pressure is the maximum pressure that can be applied to both ports of a differential pressure sensor simultaneously without damaging the sensor housing. 6. Extended temperature ranges on request. Please contact Sensortechnics. 7. Max. delay time between pressure change at the pressure die and signal change at the output. 8. The response time depends on the adjusted internal A/D resolution of the sensor. For 14 bit it is typ. 1 ms. Other A/D resolutions and reponse times are available on request. Please contact Sensortechnics for further information. 9. Sensors with lower current consumption are available on request. Please contact Sensortechnics for further information. E / 11652 / A 2/11 www.sensortechnics.com HCE Series Miniature amplified pressure sensors PERFORMANCE CHARACTERISTICS (Vs = 5.0 V, TA = 25 °C, analog output signal is ratiometric to VS, digital output signal is not ratiometric to VS, pressure applied to high pressure port) All HCE...5 devices (VS = 5.0) Characteristics Total accuracy (0...85 °C)1 Min. Typ. HCE0611..., HCE0811... all other devices Response delay7, 8 A/D resolution8 D/A resolution Current consumption (no load)9 Max. Units ±1.0 ±0.5 %FSS 1 14 ms 11 5 bi t mA HCE...R...5 (barometric devices) Characteristics Min. Typ. Max. Unit D IG IT A L P E R F O R M A N C E C H A R A C T E R IS T IC S Output at min. specified pressure Full scale span (FSS)2 Full scale output 0560 6B C 6 0666 6666 6C C C 076C Count Hex 6D D 2 A N A L O G U E P E R F O R M A N C E C H A R A C T E R IS T IC S Output at min. specified pressure Full scale span (FSS)2 Full scale output 0.21 4.21 0.25 4.00 4.25 0.29 4.29 Min. Typ. Max. V HCE...U...5 (unidirectional devices) Characteristics Unit D IG IT A L P E R F O R M A N C E C H A R A C T E R IS T IC S Zero pressure offset Full scale span (FSS)2 Full scale output 05E 3 6C 49 0666 6666 6C C C 06E 9 Count Hex 6D 4F A N A L O G U E P E R F O R M A N C E C H A R A C T E R IS T IC S Zero pressure offset Full scale span (FSS)2 Full scale output 0.23 4.23 0.25 4.00 4.25 0.27 4.27 Min. Typ. Max. V HCE...B...5 (bidirectional devices) Characteristics Unit D IG IT A L P E R F O R M A N C E C H A R A C T E R IS T IC Zero pressure offset Full scale span (FSS)2 Output 3916 at max. specified pressure at min. specified pressure 6C 49 05E 3 3999 6666 6C C C 0666 3A 1C 6D 4F 06E 9 Count Hex A N A L O G U E P E R F O R M A N C E C H A R A C T E R IS T IC S Zero pressure offset Full scale span (FSS)2 Output E / 11652 / A 2.23 at max. specified pressure at min. specified pressure 4.23 0.23 2.25 4.00 4.25 0.25 2.27 4.27 0.27 V 3/11 www.sensortechnics.com HCE Series Miniature amplified pressure sensors PERFORMANCE CHARACTERISTICS (Vs = 3.0 V, TA = 25 °C, analog output signal is ratiometric to VS, digital output signal is not ratiometric to VS, pressure applied to high pressure port) All HCE...3 devices (VS = 3.0) Characteristics Total accuracy (0...85 °C)1 Min. Typ. HCE0611..., HCE0811... all other devices Response delay7, 8 A/D resolution8 D/A resolution Current consumption (no load)9 Max. Units ±1.0 ±0.5 %FSS 1 14 ms 11 3 bi t mA HCE...R...3 (barometric devices) Characteristics Min. Typ. Max. Unit D IG IT A L P E R F O R M A N C E C H A R A C T E R IS T IC S Output at min. specified pressure Full scale span (FSS)2 Full scale output 09D 0 5F 25 0A A A 5555 5F F F 0B 85 Count Hex 60D 9 A N A L O G U E P E R F O R M A N C E C H A R A C T E R IS T IC S Output at min. specified pressure Full scale span (FSS)2 Full scale output 0.23 0.27 2.23 0.25 2.00 2.25 Min. Typ. Max. V 2.27 HCE...U...3 (unidirectional devices) Characteristics Unit D IG IT A L P E R F O R M A N C E C H A R A C T E R IS T IC S Zero pressure offset Full scale span (FSS)2 Full scale output 0A 3D 5F 92 0A A A 5555 5F F F 0B 17 Count Hex 606C A N A L O G U E P E R F O R M A N C E C H A R A C T E R IS T IC S Zero pressure offset Full scale span (FSS)2 Full scale output 0.24 0.26 2.24 0.25 2.00 2.25 Min. Typ. Max. V 2.26 HCE...B...3 (bidirectional devices) Characteristics Unit D IG IT A L P E R F O R M A N C E C H A R A C T E R IS T IC Zero pressure offset Full scale span (FSS)2 Output 34E 8 at max. specified pressure at min. specified pressure 5F 92 0A 3D 3555 5555 5F F F 0A A A 35C 2 606C 0B 17 Count Hex A N A L O G U E P E R F O R M A N C E C H A R A C T E R IS T IC S Zero pressure offset Full scale span (FSS)2 Output E / 11652 / A 1.24 at max. specified pressure at min. specified pressure 2.24 0.24 1.25 2.00 2.25 0.25 1.26 2.26 0.26 V 4/11 www.sensortechnics.com HCE Series Miniature amplified pressure sensors SPI - SERIAL PERIPHERAL INTERFACE In general the HCE series supports all combinations of clock phase (CPHA) and polarity (CPOL). By default it is programmed to CPHA = 0 and CPOL = 0, which means that data transmission starts with the rising first clock edge (see Fig 1). Introduction The HCE is capable to generate a digital output signal. The device runs a cyclic program, which will store a corrected sensor value with 14 bit resolution about every 500 µs within the output registers of the internal ASIC. This cyclic program runs independent from the bus communication. In order to use the pressure sensor for digital signal readout, it should be connected to a SPI Master device. Slave select The falling edge of the SS line indicates the beginning of the transfer. Additionally the SS line must not be negated and reasserted between the three bytes to be transmitted. SPI specifies four signals: The clock (CLK) is generated by the master and input to all slaves. MOSI carries data from master to slave. MISO carries data from slave back to master. A slave select line (SS) allows individual selection of a slave device. Data operation The MOSI line should always be set to high level. So there is no data transmission from master to slave. Because of internal configuration the slave will answer the first byte with an FFxh. The second and third byte contain the 15 bit pressure information (see Fig. 2). SPI Modes A pair of parameters called clock polarity (CPOL) and clock phase (CPHA) determine the edges of the clock signal on which the data are driven and sampled. Each of the two parameters has two possible states, which allows for four possible combinations, all of which are incompatible with one another. SCK cycle 1 2 3 For further information please refer to Sensortechnics SPI bus application note 4 5 6 7 8 SCK (CPOL=0) MOSI MSB MISO LSB MSB LSB SS Sampling Fig. 1: Example of a standard 1 byte SPI data transfer for CPHA=0 and CPOL=0 Data Byte 1 Data Byte 2 1 1 1 1 1 Data Byte 3 MOSI 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 MISO X X X X X X X X X P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P2 P1 P0 Relevant data Fig. 2: 3 byte data stream between HCE sensor and master containing the pressure value as a 15 bit information E / 11652 / A 5/11 www.sensortechnics.com HCE Series Miniature amplified pressure sensors SPI - SERIAL PERIPHERAL INTERFACE (cont.) Interface parameters Parameter Symbol Min. Typ. Max. Input high level 90 100 Input low level 0 10 Output low level Unit % of V s 10 Pull-up resistor Ω 500 Load capacitance @ MISO CMISO 400 Input capacitance @ each pin CSPI_IN 10 fSCK 100* MISO hold time after SCK sample slope tSPI_HD_MISO 200 MOSI setup time before SCK sample slope tSPI_SU_MOSI 2/fCLK tSPI_SU_SS 10 Signal clock frequency /SS setup time before SCK sample slope 640 pF kHz ns ns * recommended Note: Sensortechnics recommends communication speeds of at least 100 kHz (max. 640 kHz). Please contact your nearest Sensortechnics sales office for further information. t SPI_SU_SS t SPI_SU_MOSI t SCK (CPOL=0) SPI_HD_MISO MOSI MISO SS Fig. 3: Timing characteristics E / 11652 / A 6/11 www.sensortechnics.com HCE Series Miniature amplified pressure sensors PHYSICAL DIMENSIONS AND ELECTRICAL CONNECTIONS HCE...E8... SMD dual port, same side Straight ports 12.70 Bottom view 4.50 6.50 1.28 16 3 5 6 7 8 4 3 2 1 4.06 10.70 4.20 3 Connection 1 +Vs 2 GND 3 Vout 4 MISO 5 C LK 6 SS 7 I/C * 8 MOSI * Internal connection. Do not connect for any reason 6.70 3 1.90 2 HIGH PRESSURE PORT Pin 0.46 LOW PRESSURE PORT third angle projection 2.54 dimensions in mm HCE...E9... 12.70 Pin 4.67 00 7. 5 6 7 8 4 3 2 1 2.50 ±0.2 5 ±0.2 10.70 3,12 HIGH PRESSURE PORT 4.0 Connection 1 +Vs 2 GND 3 Vout 4 MISO 5 C LK 6 SS 7 I/C * 8 MOSI 5.21 6.87 * Internal connection. Do not connect for any reason third angle projection LOW PRESSURE PORT 2.54 E / 11652 / A 2.0 16 Ø 3.0 ±0.1 Ø 2.20 ±0.1 Bottom view Ø 2.20 ±0.1 SMD dual port, same side Barbed ports 0.46 dimensions in mm 7/11 www.sensortechnics.com HCE Series Miniature amplified pressure sensors PHYSICAL DIMENSIONS AND ELECTRICAL CONNECTIONS (cont.) HCE...H8... SMD single port Straight port Top view 12.70 Pin 1 +Vs 8 7 6 5 2 GND Vout MISO 5 C LK 6 SS 1 2 3 4 7 I/C * 10.70 8 MOSI 2 3 4 9.50 16 1.28 4.06 Connection 2.54 HIGH PRESSURE PORT 3.70 3 1.90 0.46 * Internal connection. Do not connect for any reason third angle projection 3 4.2 dimensions in mm HCE...H9... SMD single port Barbed port Top view Pin Connection 12.7 1 +Vs 2 GND 3 Vout 4 MISO 5 C LK 6 SS 7 I/C * 8 MOSI 10.5 16.0 8 7 6 5 1 2 3 4 3.8 10.7 6.2 E / 11652 / A Ø 3.0 third angle projection 6.0 Ø 2.2 2.8 9.0 HIGH PRESSURE PORT * Internal connection. Do not connect for any reason dimensions in mm 8/11 www.sensortechnics.com HCE Series Miniature amplified pressure sensors PHYSICAL DIMENSIONS AND ELECTRICAL CONNECTIONS (cont.) HCE...Q8... SMD dual port, opposite side Straight ports 12.70 Bottom view 1.28 9.50 16 2 5 6 7 8 4 3 2 1 4.06 10.70 4.20 3 +Vs 2 GND 3 Vout 4 MISO 5 C LK 6 SS 7 I/C * 8 MOSI 6.70 3 Connection 1 * Internal connection. Do not connect for any reason LOW PRESSURE PORT HIGH PRESSURE PORT 1.90 Pin third angle projection 0.46 2.54 dimensions in mm HCE...Q9... SMD dual port, opposite side Barbed ports Top view 6.2 4.0 Pin 16 10.5 12.7 8 7 6 5 1 2 3 4 3.1 10.7 6.9 LOW PRESSURE PORT 1 +Vs 2 GND 3 Vout 4 MISO 5 C LK 6 SS 7 I/C * 8 MOSI * Internal connection. Do not connect for any reason 6.0 E / 11652 / A Ø 2.2 Ø 3.0 2.2 5.0 HIGH PRESSURE PORT Connection third angle projection dimensions in mm 9/11 www.sensortechnics.com HCE Series Miniature amplified pressure sensors HOUSING OPTIONS Different housing options are available on request. Please contact Sensortechnics. Dual Inline Packages (DIP) (Sample package shown: DIP dual port, same side) 12.70 4.50 6.50 16.0 16.25 3.0 5 6 7 8 4 3 2 1 9.0 10.70 3.0 4.20 HIGH PRESSURE PORT LOW PRESSURE PORT 2.54 0.46 5.60 1.90 2.0 6.70 3.0 third angle projection dimensions in mm Single Inline Packages (SIL) (Sample package shown: SIL same top side) 12.70 6.70 7.85 4.85 3 2 10.30 16 10.70 4.20 3 1.90 4 3 2 1 0.25 0.51 1.45 2.54 HIGH PRESSURE PORT 1.90 10.70 third angle projection dimensions in mm LOW PRESSURE PORT E / 11652 / A 10/11 www.sensortechnics.com HCE Series Miniature amplified pressure sensors ORDERING INFORMATION Series Options HCE Pressure range Pressure mode 600...1100 mbar A* Absolute B Bidirectional 0811 800...1100 mbar D Differential U Unidirectional Gage R* Barometric M010 10 mbar G M020 20 mbar M050 50 mbar M100 100 mbar M200 200 mbar M500 500 mbar B 001 1 bar (B001A) 1 bara B 002 2 bar B 005 5 bar Note: HCE M050 Housing E* D * for pressure ranges 0611, 0811 B Porting SMD, 2 ports, same side 8* Straight Grade P Prime 9** Barbed Voltage 3 3V 5 5V H** SMD, 1 port Q* * only available for pressure ranges 0611, 0811, B 001, B 002 Example: Calibration 0611 SMD, 2 ports, opposite side Housings Q only available * standard for up to 1 bar. Please devices up to 500 mbar and contact Sensortechnics. barometric ranges * standard for differential ** standard for devices, "D" devices from ** standard for absolute 1 bar and gage devices, "A" and "G" E 8 P 5 Devices highlighted in grey are preferred stock items Custom specific pressure ranges and mechanical or electronic sensor modifications are widely available: · I2C, switching and custom specific outputs · Dual inline packages (DIP) · Single inline packages (SIL) ... etc. Please contact your nearest Sensortechnics sales office for further information. Sensortechnics PRO services: · Extended guarantee period of 2 years · Custom product modifications and adaptations even for small quantities · Advanced logistics models for supply inventory and short delivery times · Technical support through application engineers on the phone or at your site · Traceability of each sensor through serial numbers on request · No product specification changes without customer notification · No product obsolescence without very early prior notice · Fastest possible technical response for design and QA engineers · Long term product availability for your spares and service needs ... plus other services on request Sensortechnics reserve the right to make changes to any products herein. Sensortechnics do not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. E / 11652 / A 11/11 www.sensortechnics.com