Ordering number : ENA1568A Bi-CMOS IC LV4985VH For Portable Electronic Device Use 1.2W × 2ch BTL Power Amplifier Overview The LV4985VH has a 2-channel power circuit amplifier including an electronic volume control built in. It has a function for switching the headphone driver and also has a standby function to reduce the current drain. It is a power amplifier IC optimal for driving the speakers used in portable equipment and low power output equipment. Applications Portable DVD players, active speakers, compact LCD-TVs/LCD monitors, notebook PCs and more. Features • 2-cannels BTL power amplifier built-in : Standard output power = 1.2W (VCC = 5V, RL = 8Ω, THD = 10%) Output coupling capacitor is unnecessary because of differential output type. • Volume function built-in (variable range: 69dB standard), DC voltage control system • Mute function built-in (shared with VOL-min) • Standby function built-in (three-value control ⇒ Shared with the second amplifier stop control pin) : Standard standby current = 0.01μA (VCC = 5V) • Second amplifier stop control function built-in (three-value control ⇒ Shared with the standby pin) : Headphone driver switch (for BTL/SE switch) Simple MUTE (Only BTL power amplifier path) • Thermal protection circuit built-in • Operation supply voltage range : VCC = 4.5V to 5.5V • Output phase compensation capacitor not necessary Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. D1609 SY / O1409 SY PC 20090914-S00001 No.A1568-1/15 LV4985VH Specifications Maximum Ratings at Ta = 25°C Parameter Symbol Maximum supply voltage VCC max Allowable power dissipation Pd max Conditions Ratings * Mounted on a specified board.* Unit 6 V 1.45 W 150 °C Maximum junction temperature Tj max Operating temperature Topr -20 to +75 °C Storage temperature Tstg -40 to +150 °C * Specified board (SANYO Semiconductor Evaluation board) : 50mm × 50mm × 1.6mm, glass epoxy both side. Operating Conditions at Ta = 25°C Parameter Symbol Recommended supply voltage VCC Recommended load resistance RL Allowable operating supply voltage VCC op Conditions Ratings Unit 5 V 8 to 32 Ω 4.5 to 5.5 V range Electrical Characteristics at Ta = 25°C, VCC = 5V, fin = 1kHz, RL = 8Ω, V9 = 2.5V, V10 = 3V, pwr-amp-VG = 20.7dB Parameter Symbol Ratings Conditions min typ Unit max Quiescent current drain ICCOP No signal, no load 11.5 20 mA Standby current drain ISTBY No signal, V9 = 0.3V 0.01 5 μA Maximum output power PO max THD = 10% 0.8 1.2 25.8 27.8 W BTL voltage gain VG Vin = -30dBV Volume voltage gain VGVOL Vin = -30dBV, volume output pin 29.8 dB Channel balance CHBAL Vin = -30dBV +2 dB Total harmonic distortion THD Vin = -30dBV 0.4 1 Maximum output noise voltage VN max Rg = 620Ω, 20 to 20kHz 0.7 1.4 Minimum output noise voltage VN min Rg = 620Ω, 20 to 20kHz 0.06 Channel separation CHsep Vin = -20dBV, Rg = 620Ω Volume variable range WVOL Vin = -30dBV Mute attenuation level ATTMT Vin = -10dBV, V10 = 0.25V, 1kHz-BPF Ripple rejection ratio SVRR Rg = 620Ω, fr = 100Hz, Vr = -20dBV Output DC offset voltage VOS Reference voltage VREF 7.1 -2 58 -72 0 dB mVrms 66 dB 69 dB -82 dBV 30 -30 Pin 6 voltage, % mVrms dB +30 2.5 mV V Amplifier operation reference DC voltage source Volume maximum control voltage MXVOL Pin 10 control voltage 2.8 Muting control voltage VMT Pin 10 control voltage 0 0.25 V V High level control voltage (pin 9) V9CH Full operating mode (BTL mode) 2.3 VCC V Middle level control voltage (pin 9) V9CM Second amplifier non-operating mode (SE mode) 1.3 1.7 V Low level control voltage (pin 9) V9CL Standby (shutdown) mode 0 0.3 V No.A1568-2/15 LV4985VH Package Dimensions unit : mm (typ) 3313 Pd max -- Ta 6.5 0.5 6.4 8 4.4 14 1 1.3 7 0.22 0.15 0.65 1.5 1.45 SANYO evaluation board (double-sided) : 50 × 50 × 1.6mm3 (glass epoxy) 1.2 0.87 0.8 0.4 0.35 Independent IC 0.21 0 --20 0 20 40 60 80 100 Ambient temperature, Ta -- °C 0.1 (1.3) 1.5max (2.35) Maximum power dissipation, Pd max -- W 1.6 SANYO : HSSOP14(225mil) No.A1568-3/15 LV4985VH PIN2 VLOUT2 VOL STBY IN2 13 12 11 10 9 8 VOLUME CNT BIAS CNT 2nd-AMP CNT OUT2-1 14 - OUT2-2 2st-amp + Radiator Fin GND VOLUME Block Diagram 1st-amp - VCC + TSD + GND - VOLUME Radiator Fin 2st-amp + 1st-amp 1 2 3 4 5 6 7 OUT1-2 OUT1-1 VCC PIN1 VLOUT1 VREF IN1 Test Circuit Vvol V9cnt 14 13 12 11 10 9 8 1 2 3 4 5 6 7 Vin + VCC No.A1568-4/15 LV4985VH Evaluation Board Circuit OUT2-2 OUT2-1 SE2 VOL STBY IN2 100μF + 100kΩ 18kΩ 0.33μF 0.33μF 14 13 12 11 10 9 8 1 2 3 4 5 6 7 100kΩ 18kΩ 0.33μF 1μF 0.33μF + 100μF OUT1-2 OUT1-1 SE1 0.1μF + IN1 2.2μF VCC GND Evaluation Board Layout (50mm × 50mm × 1.6mm) Top Layer Bottom Layer No.A1568-5/15 LV4985VH Application Circuit Example 1 C8 Speaker R4 R3 100kΩ 18kΩ R7 from CPU from CPU (BTL mode only) R8 0.33μF R5 C4 0.33μF 14 13 12 11 10 9 8 1 2 3 4 5 6 7 R2 100kΩ R1 18kΩ C3 0.33μF C5 1μF C2 Vin2 C1 Vin1 0.33μF Speaker + C6 C7 0.1μF 2.2μF VCC Application Circuit Example 2 C8 Speaker R4 R3 100kΩ 18kΩ R7 R8 R5 R6 from CPU 100μF from CPU 33Ω to CPU C10 + 0.33μF C4 0.33μF 14 13 12 11 10 9 8 1 2 3 4 5 6 7 C2 Vin2 C1 Vin1 100KΩ R13 100KΩ R14 R12 1KΩ R10 from CPU (BTL mode/SE mode changeover) VCC R11 1KΩ R2 100kΩ R1 18kΩ Speaker R9 C9 + 33Ω 100μF C3 0.33μF C5 1μF 0.33μF + C6 C7 0.1μF 2.2μF VCC No.A1568-6/15 LV4985VH Pin Functions Pin No. Pin Name Pin Voltage Description Equivalent Circuit VCC = 5V 1 OUT1-2 14 OUT2-2 2.49 Power amplifier 2nd output pin. VCC VCC VREF + 1 14 - 10kΩ GND 2 OUT1-1 13 OUT2-1 2.49 Power amplifier 1st output pin. VCC VCC VREF + 2 13 - 10kΩ 30kΩ GND 3 VCC 5.0 Power supply pin. 4 PIN1 2.49 Power amplifier input pin. 12 PIN2 VCC 12 4 + VREF 5 VLOUT1 11 VLOUT2 2.49 Volume output pin. VCC VREF + 6 VREF 2.49 5 11 - VOL Ripple filter pin. VCC (for filtering capacitor connection) VREF VCC 50kΩ 6 600kΩ 50kΩ GND 7 IN1 8 IN2 0 Input pin. VCC 15kΩ 8 7 + - 5kΩ GND Continued on next page. No.A1568-7/15 LV4985VH Continued from preceding page. Pin No. Pin Name Pin Voltage Description Equivalent Circuit VCC = 5V 9 STBY External apply Standby/2nd amplifier stop control pin. VCC 0 to 0.3V ⇒ Standby mode VCC 1.3 to 1.7V ⇒ SE mode 2.3 to VCC ⇒ BTL mode + 30kΩ - 9 150kΩ VB1 GND 10 VOL External apply Volume control pin. VCC VCC 10 GND Usage Note 1. Input coupling capacitor (C1 and C2) C1 (C2) is an input coupling capacitor that is used to cut the DC component. The input coupling capacitor C1 (C2) and the input resisters of 20kΩ (15kΩ + 5kΩ) make up a high-pass filter, attenuating the bass frequency. Therefore, the capacitance value must be selected with due consideration of the cut-off frequency. The cut-off frequencies are expressed by the following formulas. 1ch ⇒ fc1 = 1/ (2π × C1 × 20000) 2ch ⇒ fc2 = 1/ (2π × C2 × 20000) This capacitor affects the pop noise at startup. Note with care that increasing the capacitance value lengthens the charging time of the capacitor, which will make the pop noise louder. 2. Input coupling capacitors (C3 and C4) in the power amplifier block C3 (C4) is an input coupling capacitor that is used to cut the DC component. The input coupling capacitor C3 (C4) and the input resistor R1 (R3) make up a high-pass filter, attenuating the bass frequency. Therefore, the capacitance value must be selected with due consideration of the cut-off frequency. The cut-off frequencies are expressed by the following formulas. 1ch ⇒ fc3 = 1/ (2π × C3 × R1) 2ch ⇒ fc4 = 1/ (2π × C4 × R3) This capacitor affects the pop noise at startup. Note with care that increasing the capacitance value lengthens the charging time of the capacitor, which will make the pop noise louder. 3. BTL voltage gain of the power amplifier block The voltage gain of the first amplifier is determined by the ratio between the resistors R1 and R2 (R3 and R4). 1ch ⇒ Vg1 = 20 × log (R2/R1) … unit : dB 2ch ⇒ Vg2 = 20 × log (R4/R3) … unit : dB Therefore, the BTL voltage gain of the power amplifier block is expressed by the following formulas. 1ch ⇒ VgBTL1 = 6 + 20 × log (R2/R1) … unit : dB 2ch ⇒ VgBTL2 = 6 + 20 × log (R4/R3) … unit : dB The BTL voltage gain of the power amplifier block must be set in the range of 0 to 26dB. No.A1568-8/15 LV4985VH 4. pin 6 capacitor (C5) This capacitor is a ripple filter capacitor. The internal resistors (600kΩ + 50kΩ) and C5 make up a low-pass filter that is used to reduce the power supply ripple component and increase the ripple rejection ratio. Note that inside the IC, the rising-transient-response-characteristic of the pin 6 voltage (reference voltage) is used to activate the automatic pop noise reduction circuit. Therefore, when reducing the C5 capacitance value to increase the voltage rise speed, the design should take into account that the pop noise increases during voltage rise. 5. Power supply line capacitor (C6 and C7) The bypass capacitor C7 is used to remove the high frequency component that cannot be eliminated by the power supply capacitor C6 (chemical capacitor). Place the bypass capacitor C7 as near to the IC as possible, and use a ceramic capacitor with good high frequency characteristics. When using a stabilized power supply, these capacitors can also be combined into a single 2.2μF ceramic capacitor. Note that when the power supply line is relatively unstable, the power supply capacitor C6 capacitance value must be increased. 6. Load capacitance When connecting a capacitor between the output pin and ground to suppress electromagnetic radiation or other purposes, the effects of this capacitor may cause the power amplifier phase margin to be reduced, resulting in oscillation. When adding this capacitor, care should be taken for the capacitance value. Recommended capacitance value : 1000pF to 0.1μF 7. Headphone drive When also using the BTL amplifier’s first amplifier as the headphone amplifier, it is recommended to adjust the level by inserting series resistors R9 (R10) to the signal line as shown in Application Circuit Example-2. Note that this series resistor, the headphone load resistance and the output coupling capacitors C9 (C10) make up a high-pass filter, so this should be taken into account in the design. The cut-off frequencies are expressed by the following formulas. 1ch ⇒ fc5 = 1/ (2π × C9 × (R9 + RL)) 2ch ⇒ fc6 = 1/ (2π × C10 × (R10 + RL)) 8. Standby pin (pin 9) As shown in Figure1, by controlling the standby pin, the mode changeover can be made between standby mode, single-ended (SE) operating mode, and BTL operating mode. State Standby mode Pin 9 voltage Port A Port B 0V to 0.3V Low Low SE operating mode 1.3V to 1.7V High Low BTL operating mode 2.3V to VCC High High A-port B-port R5 R5 STBY 9 A-port R6 CPU LV4985VH Fig. 1 R5 9 STBY 9 STBY VCC 3 VCC CPU Fig. 2 Fig. 3 When not using the single-ended operating mode, a direct control is possible by connecting the standby pin to the CPU output port. However, it is recommended to insert a series resistor R5 (1kΩ or more) as shown in Figure 2 in case the pin is affected by the digital noise from CPU. In addition, when not using the standby mode, the pin 9 can also be used interlocked with the power supply as shown in Figure 3. Since there exists an internal current limiting resistor (30kΩ), the series resistor R5 can be eliminated, but the current I9 expressed by the following formula flows through the pin 9, so this should be taken into account in the design. Pin 9 inflow current (unit : A) : I9 = 4.7 × 10-6 + (VCC - 0.7)/(R5 + 30000) No.A1568-9/15 LV4985VH 9. Electronic volume control (pin 10 control) By changing voltage applied to the pin 10, the voltage gain of the built-in VCA(variable control amplifier) is varied. Since the ripple component of applied voltage is generated, a stabilized power source must be used. When controlling the amplifier using the PWM signal from the CPU, use a resistor and capacitor for DC conversion as shown in Figure 4 and adjust the voltage gain by changing the pulse width of PWM signal. In this case, the frequency of PWM signal used must be higher than audio frequency band. R7 PWM output 10 VOL C8 R8 CPU LV4985VH PWM signal Discharge resistor Fig. 4 10. Thermal protection circuit The IC has a built-in thermal protection circuit that can reduce the risk of breakdown or degradation when the IC becomes abnormally hot for some reason. When the internal chip junction temperature Tj rises to approximately 170°C, this protective circuit operates to cut off the power supply to the power amplifier block and stop signal output. Operation recovers automatically when the chip temperature drops to approximately 130°C. Note that this circuit cannot always prevent breakdown or degradation, so sufficient care should be taken for using the IC. When the chip becomes abnormally hot, immediately turn off the power and determine the cause. 11. Short-circuit between pins Turning on the power supply with the short-circuit between terminals leads to the deterioration and destruction of IC. When fixing the IC to the substrate, please check that the solder is not short-circuited between the terminals before turning on the power. 12. Load Short-circuit Leaving the IC in the load short-circuit for many hours leads to the deterioration and destruction of the IC. The load must not be short-circuited absolutely. 13. Maximum rating When the rated value used is just below to the absolute maximum ratings value, there is a possibility to exceed the maximum rating value with slight extrusion variable. Also, it can be a destructive accident. Please use within the absolute maximum ratings with sufficient variation margin of supply voltage. In addition, the package of this IC has low thermal radiation characteristics, so secure sufficient thermal radiation by providing a copper foil land on the printed circuit board near the heat sink. No.A1568-10/15 THD -- PO 100 7 5 10 7 Total harmonic distortion, THD -- % Total harmonic distortion, THD -- % LV4985VH 3 2 10 7 5 3 2 1 7 5 3 2 0.1 0.01 2 3 5 7 0.1 2 3 5 7 2 1 3 5 THD -- f VCC = 5V PO = 200mW VG = 27.8dB V10 = 3V 3 2 1 7 5 3 2 0.1 10 5 7 10 2 3 5 7 100 Output power, PO -- mW 1.0 VCC = 5V fin = 1kHz 7 2 3 5 7 10k 2 3 5 7100k ICC -- PO VCC = 5V fin = 1kHz 5 Current drain, ICC -- A Power dissipation, Pd -- W 1.2 1.0 0.8 0.6 0.4 3 2 0.1 7 5 3 2 0.2 0 0.01 2 3 5 7 0.1 2 3 5 7 1 2 3 0 0.01 5 7 10 2 3 5 7 0.1 Output power, PO -- W/ch 3 5 7 2 1 3 5 7 10 Volume - Att -- V10cnt 20 VCC = 5V Vin = -26dBV Volume attenuation value , Att -- dB 7 5 3 2 1 7 5 3 2 0.1 --30 2 Output power, PO -- W/ch THD -- Vin 10 0 --20 --40 --60 --80 --100 --28 --26 --24 --22 --20 --18 --16 --14 --12 --10 --8 0.5 0 Input level, Vin -- dBV VNO -- V10cnt 1 1 1.5 2 2.5 3 Pin 10 control voltage, V10cnt -- V VMT -- fin --50 7 Mute control voltage, VMT -- dBV Total harmonic distortion, THD -- dB 5 7 1k Frequency, f -- Hz Pd -- PO 1.4 2 3 5 3 2 0.1 7 5 3 2 0.01 0 0.5 1 1.5 2 2.5 Pin 10 control voltage, V10cnt -- V 3 --60 V --70 V, 0.3 = 10 --80 V = V9 9 = 2.3 5V 1. ,V 3V = 10 V10 = 3V, V9 = 0.3V --90 V --100 --110 --120 10 2 3 5 7 100 2 3 5 7 1k 2 3 5 7 10k 2 3 5 7100k Input frequency, fin -- Hz No.A1568-11/15 LV4985VH CHsep -- fin Ripple rejection ratio, SVRR -- dB 70 60 50 40 10 2 3 5 7 100 2 3 5 7 1k SVRR -- f 70 2 3 5 7 10k 2 3 60 IN M LVO Channel separation, CHsep -- dB 80 50 40 VOL-MAX 30 20 10 10 5 7100k 2 3 5 7 100 Input frequency, fin -- Hz Quiescent current drain, ICCO -- mA No load No signal 0.05 2.5V , V9 = V 3 = V10 V 9 = 2.5 0.3V, V V10 = 1.5V V, V9 = V10 = 3 12 10 8 5 7 10k 2 3 5 7100k ISTBY -- VCC No load No signal V9 = 0.3V 0.03 6 0.02 4 0.01 2 0 1 2 3 4 5 0 0 6 1 Supply voltage, VCC -- V Maximum output power, PO max -- W C 25 3 2 -25 C 10 7 5 1 7 5 3 2 0.1 10 2 3 5 7 100 2 3 5 7 1000 2 3 1 --20 --10 Channel separation, CHsep -- dB 3 2 0 10 20 30 40 0 50 Ambient temperature, Ta -- C 10 20 30 40 50 60 70 80 60 70 80 CHsep -- Ta 80 5 --10 6 Ambient temperature, Ta -- C THD -- Ta --20 5 1.2 0.8 --30 5 710000 7 0.1 --30 4 1.4 Output power, PO -- mW 1 3 PO max -- Ta 1.6 50 C 3 2 2 Supply voltage, VCC -- V THD -- PO 100 7 5 Ta = 80 C Total harmonic distortion, THD -- % 2 3 0.04 0 Total harmonic distortion, THD -- % 5 7 1k Frequency, f - Hz ICCO -- VCC 14 2 3 60 70 80 75 70 65 60 55 50 --30 --20 --10 0 10 20 30 40 50 Ambient temperature, Ta -- C No.A1568-12/15 LV4985VH SVRR -- Ta 20 Volume attenuation value , Att -- dB Ripple rejection ratio, SVRR -- dB 80 70 VOL-MIN 60 50 40 VOL-MAX 30 20 --30 --20 --10 0 10 20 30 40 50 60 70 Volume - Att -- Vvol VCC = 5V Vin = -30dBV 0 --20 --40 C a= 25 T C -25 --60 0.5 Ambient temperature, Ta -- C Voltage gain, VG -- dB Voltage gain, VG -- dB 9 29 28 27 26 --30 --20 --10 0 10 20 30 40 50 60 70 8 --20 --10 600 60 20 30 40 50 60 70 50 --30 80 --20 --10 Ambient temperature, Ta -- C 0.48 Pin 10 control voltage, V10cnt -- V Mute control voltage, VMT -- dBV --80 V10 = 0.3V, V9 = 2.3V --90 V10 = 3V, V9 = 0.3V --100 V10 = 3V, V9 = 1.5V --110 --30 --20 --10 0 10 20 30 40 50 Ambient temperature, Ta -- C 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80 60 70 80 Ambient temperature, Ta -- C VMT -- Ta --70 10 VNO -- Ta 90 70 10 0 Ambient temperature, Ta -- C 700 0 3 6 80 --10 2.5 Volume - VG -- Ta 5 --30 80 VNO -- Ta --20 2 7 800 500 --30 1.5 VCC = 5V V10 = 3V Vin = -30dBV fin = 1kHz OUTPUT : VLOUT Ambient temperature, Ta -- C 900 1 Control voltage, Vvol -- V VG -- Ta 30 C --80 --100 0 80 80 60 70 80 V10cnt -- Ta VCC = 5V V9 = 2.5V mute mode 0.46 0.44 0.42 0.4 --30 --20 --10 0 10 20 30 40 50 Ambient temperature, Ta -- C No.A1568-13/15 LV4985VH V9cnt -- Ta 2.2 VCC = 5V V10 = 3V SE mode Pin 9 control voltage, V9cnt -- V Pin 9 control voltage, V9cnt -- V 1 0.9 0.8 0.7 0.6 --30 --20 --10 0 10 20 30 40 50 60 70 V9cnt -- Ta VCC = 5V V10 = 3V BTL mode 2.1 2 1.9 1.8 --30 80 --20 --10 Ambient temperature, Ta -- °C 14 ICCOP -- Ta VCC = 5V V9 = 2.5V V10 = 3V No load No signal Standby current drain, ISTBY -- μA Quiescent current drain, ICCOP -- mA 15 13 12 11 10 9 --30 --20 --10 0 10 20 30 40 50 Ambient temperature, Ta -- °C 0 10 20 30 40 50 60 70 80 70 80 Ambient temperature, Ta -- °C 60 70 80 1 7 5 ISTBY -- Ta V9 = 0.3V No signal 3 2 V 0.1 7 5 V CC =6 5V 3 2 0.01 7 5 3 2 0.001 --30 --20 --10 0 10 20 30 40 50 60 Ambient temperature, Ta -- °C No.A1568-14/15 LV4985VH •Transient response characteristics (volume max. setting) Rising (V9 ⇒ high) characteristics Falling (V9 ⇒ low) characteristics 50ms/div Load end : 50mV/div 50ms/div Load end : 50mV/div First output pin : 1V/div First output pin : 1V/div Pin 9 : 5V/div Pin 9 : 5V/div •Transient response characteristics (volume mute. setting) Rising (V9 ⇒ high) characteristics Falling (V9 ⇒ low) characteristics 50ms/div Load end : 50mV/div 50ms/div Load end : 50mV/div First output pin : 1V/div First output pin : 1V/div Pin 9 : 5V/div Pin 9 : 5V/div SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of December, 2009. Specifications and information herein are subject to change without notice. PS No.A1568-15/15