Optically Coupled Isolator OPI7002, OPI7002RCE, OPI7010, OPI7010RCE OPI7320RCE, OPI7340RCE Features: ± 6 kV dc electrical isolation Inexpensive plastic housing Choice of phototransistor or photodarlington output UL registered File No. E58730 Description: Each OPI7002 and OPI7010 consists of an infrared emitting diode coupled to a NPN silicon phototransistor. The LED and sensor are encased in a black, low-cost plastic housing. Pin spacing is compatible with standard dual-in-line packages. Each OPI7320RCE and OPI7340RCE consists of an infrared emitting diode coupled to a NPN silicon photodarlington. The LED and sensor are encased in a high dielectric plastic housing. Pin spacing is compatible with standard dual-in-line packages. The RCE versions reverses the Phototransistor Emitter and Collector pin-out. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Ordering Information Applications: Requiring high voltage isolation between input and output Electrical isolation in dirty environments Part Number OPI7002 Industrial equipment OPI7010 Medical equipment OPI7320RCE Office equipment OPI7340RCE OPI7002, OPI7010 2 1 3 4 LED Peak Wavelength Sensor Isolation Voltage (,000) 890 nm Transistor 6 890 nm or 935 nm Darlington 6 CTR Min Lead IF (mA) VCE (Volts) Length / Typ / Max Max Spacing 20 100 200 400 10 / 50 30 0.30" / 0.30" 5 / 50 15 0.30" / 0.30" OPI7002RCE, OPI7010RCE 2 1 3 Pin # LED Pin # Transistor/ RCE 2 1 Cathode Anode 3 4 Collector / Emitter Emitter / Collector 4 OPI7320RCE, OPI7340RCE 2 3 1 DIMENSIONS ARE IN: RoHS 4 [MILLIMETERS] INCHES General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc TT Electronics | OPTEK Technology 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.ttelectronics.com | www.optekinc.com Issue C 10/2017 Page 1 Optically Coupled Isolator OPI7002, OPI7002RCE, OPI7010, OPI7010RCE OPI7320RCE, OPI7340RCE Absolute Maximum Ratings (TA = 25° C unless otherwise noted) Operating Temperature Range -40° C to +85° C Storage Temperature Range Input-to-Output Isolation Voltage -40° C to +85° C (1)(4) ±6 kVDC Lead Soldering Temperature [1/16 inch (1.6 mm) from the case for 5 seconds with soldering iron(2) 260° C Input Diode Forward DC Current 50 mA Peak Forward current (1 µs pulse width, 300 pps) 3A Reverse Voltage 2V Power Dissipation (3) 100 mW Output Phototransistor Collector-Emitter Voltage OPI7002, OPI7010, OPI7002RCE, OPI7010RCE 30 V OPI7320RCE, OPI7340RCE 15 V Emitter-Collector Voltage Power Dissipation Notes: (1) (2) (3) (4) 5.0 V (3) 100 mW Measured with input leads and output leads shorted. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. Derate linearly 1.66 mW/° C above 25° C. UL recognition is for 6kV dc for one minute General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc TT Electronics | OPTEK Technology 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.ttelectronics.com | www.optekinc.com Issue C 10/2017 Page 2 Optically Coupled Isolator OPI7002, OPI7002RCE, OPI7010, OPI7010RCE OPI7320RCE, OPI7340RCE Electrical Characteristics (TA = 25° C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode (See OP140 or OP240 for additional information—for reference only) VF Forward Voltage - 1.2 1.70 V IF = 10 mA IR Reverse Current - - 100 µA VR = 2.0 V Output Phototransistor (OPI7002, OPI7010) (See OP550 for additional information—for reference only) Output Photodarlington (OPI7320, OPI7340) (See OP560 for additional information—for reference only) V(BR)CEO Collector-Emitter Breakdown Voltage OPI7002/RCE, OPI7010/RCE OPI7320RCE, OPI7340RCE V(BR)ECO ICEO 30 15 - - V Emitter-Collector Breakdown Voltage 5 - - V Collector-Emitter Dark Current - - 100 nA 20 100 200 400 - - IC = 100 µA, IF = 0 IE = 100 µA, IF = 0 VCE = 10 V, IF = 0 Coupled IC/ IF DC Current Transfer Ratio OPI7002, OPI7002RCE OPI7010, OPI7010RCE OPI7320RCE OPI7340RCE V(SAT) Collector-Emitter Saturation Voltage OPI7002/RCE, OPI7010/RCE OPI7320RCE, OPI7340RCE - - 0.4 1.0 V VISO Isolation Voltage(1) 6 - - kVDC T(ON) Turn-On Time OPI7002/RCE, OPI7010/RCE OPI7320RCE, OPI7340RCE - 4 150 - T(OFF) Turn-Off Time OPI7002/RCE, OPI7010/RCE OPI7320RCE, OPI7340RCE - 3 125 - - 0.2 - CIO Capacitance Input-to-Output(1) % IF = 10 mA, VCE = 5 V IF = 10 mA, VCE = 5 V IF = 5 mA, VCE = 5 V IF = 5 mA, VCE = 5 V IF = 10 mA, IC = 0.50 mA IF = 5 mA, IC = 2 mA See note 1 µs VCE = 10 V, IC = 10 mA, RL = 100 Ω pF VIO = 0, F = 1 MHz Notes: (1) Measured with input leads and output leads shorted. General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc TT Electronics | OPTEK Technology 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.ttelectronics.com | www.optekinc.com Issue C 10/2017 Page 3