MAFA 1014-PA Optical Preamplifier Erbium Doped Fiber Preamplifier DATASHEET | SEPTEMBER 2013 FIBER OPTICS EMCORE’s MAFA 1014-PA Optical Preamplifier Erbium Doped Fiber Gain Block Module is an ideal building block for system integrators to extend the fiber link for long-haul signal transport. The MAFA 1014-PA Optical Preamplifier series gain blocks are designed to meet the most demanding noise performance requirements of fiber optic communications and control systems and performs all the functions required of an optical preamplifier for system integration. The MAFA 1014-PA Optical Preamplifier provides output optical isolation for stable, low noise operation. The output optical signal power level is detected for monitoring and control. The very low level input optical signal is amplified with active output power control for constant current mode operation. Applications The compact mechanical footprint of the MAFA 1014-PA Optical Preamplifier allows using this unit to be installed in small space environments. CATV Systems Long Distance RF/Microwave Fiber Optic Communication Links Sensing and Control Systems General and Mechanical Specifications High-Performance Supertrunking Links High Power Distribution Networks Parameter Min Typ Max Units 1532 - 1565 nm Standard 0 - 50 °C Standard* Storage Temperature -40 - 85 °C Standard Operating Humidity 20 - 85 % Non-condensing - +12/+5/+3.3 - VDC All Versions** Redundant Ring Architectures Operating Wavelength FTTx Networks Operating Case Temperature Features Voltage Supply Range Comments Full Function Fiber Optic pre-Amplifier Optical Connectors - SC; FC; E2000 - - User Specified Low Noise Figure (NF Typ < 3.3 dB) Dimensions (mm) - 70 x 90 x 15 - Mm All Versions Pin > -45 dBm Pout (saturated): ≈ +14 dBm Small Signal Gain > 37 dB Low Electrical Power Consumption * - Extended temperature range of – 40ºC to +75ºC is also possible ** Transient Pulse to +X.X VDC + 5% for < 100 msec Electrical power must be applied to the unit only after launching input optical Output Isolation > 40 dB Polarization Dependant Gain < 0.1 dB Polarization Mode Dispersion < 0.2 ps Output Return Losses < -40 dB Output Residual Pump Power < -40 dBm | REV 2013.09 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. MAFA 1014-PA Optical Preamplifier Erbium Doped Fiber Preamplifier FIBER OPTICS DATASHEET | SEPTEMBER 2013 Optical/Electrical Characteristics1 Property Model 1400 Comments (Note 1) Max 0 - Min -45 - Pout (dBm) Nominal 14 +/- .25 (Notes 2,3) NF (dB) Max 3.3 dB (Note 4) (dB) Max +/- 0.1 (Note 5) Psys(W) Max 2 70°C Case Unit Limit Operating Input Power Pin (dBm) Operating Input Power Pin (dBm) Saturated Output Power Noise Figure Output Power Stability Power Consumption (Steady state) Notes: 1. Unless stated otherwise, all specifications apply over the full operating temperature and humidity ranges 2. Measurement variations 3. Measured @ 1550 nm and Pin = -4 dBm 4. Measure @ 1550 nm and Pin = -30 dBm 5. Over polarization and temperature Outline Drawing (dimensions in mm) | REV 2013.09 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. MAFA 1014-PA Optical Preamplifier Erbium Doped Fiber Preamplifier FIBER OPTICS DATASHEET | SEPTEMBER 2013 Compliance and Reliability Information FCC: Subpart B. Part 15 class “A”: Unintentional Radiators EN 55013: Sound and Television Broadcast receivers and associated equipment – Radio disturbance characteristics- limits and methods of measurements – Electric Field Radiation Emissions (2001) Fit Rate: 90% level of confidence - 290 @ 25°C Electrical Connector Pinout PIN # Designation PIN # Designation 1 +12 VDC/+5 VDC/+3.3 VDC 16 LED_Laser_ON 2 +12 VDC/+5 VDC/+3.3 VDC 17 N/A 3 +12 VDC/+5 VDC/+3.3 VDC 18 Pump_Bias_Alarm * 4 +12 VDC/+5 VDC/+3.3 VDC 19 Loss_Input_Power * 5 GND 20 Loss_Output_Power * 6 GND 21 N/A 7 RS232_Rx 22 N/A 8 RS232_Tx 23 N/A 9 GND 24 N/A 10 GND 25 N/A 11 LED_Comm 26 N/A 12 EDFA_Reset 27 N/A 13 EDFA_Disable 28 N/A 14 Pout_Mute 29 N/A 15 EDFA_Temp_Alarm * 30 N/A * - software adjustable parameters; logic levels (low / high) TBD Ordering Information MAFA-PA-1014 - - - Connector Option Temp Options Voltage Options SC1 - SC/APC S – Standard 1 - +12 VDC S21 - SC/PC E – Extended 2 - +5 VDC FC1- FC/APC - 3 - +3.3 VDC FC2- FC/PC - - EC1-E2000/APC - - Example: MAFA-PA-1014-SC1-S-2: 14 dBm pre-amp gain block with SC/APC optical connectors, standard temperature range, +5 VDC power supply | REV 2013.09 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. MAFA 1014-PA Optical Preamplifier Erbium Doped Fiber Preamplifier DATASHEET | SEPTEMBER 2013 FIBER OPTICS Laser Safety Information This component product does not meet the applicable requirements of 21 CFR 1010 & 1040 and is classified as a Class IIIb laser product based on the maximum optical output power defined below. During use as intended, the laser energy is fully contained within the fiber network such that there is no accessible laser radiation and would meet the requirements for a Class I laser product. Wavelength = 1532 ~ 1565 nm (dependent on input source) Maximum Output Power = 200 mW | REV 2013.09 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.