TI LM2917MX Lm2907/lm2917 frequency to voltage converter Datasheet

LM2907-N, LM2917-N
www.ti.com
SNAS555C – JUNE 2000 – REVISED MARCH 2013
LM2907/LM2917 Frequency to Voltage Converter
Check for Samples: LM2907-N, LM2917-N
FEATURES
DESCRIPTION
•
The LM2907, LM2917 series are monolithic
frequency to voltage converters with a high gain op
amp/comparator designed to operate a relay, lamp, or
other load when the input frequency reaches or
exceeds a selected rate. The tachometer uses a
charge pump technique and offers frequency
doubling for low ripple, full input protection in two
versions (LM2907-8, LM2917-8) and its output swings
to ground for a zero frequency input.
1
2
•
•
•
•
•
•
•
Ground Referenced Tachometer Input
Interfaces Directly With Variable Reluctance
Magnetic Pickups
Op Amp/Comparator Has Floating Transistor
Output
50 mA Sink or Source to Operate Relays,
Solenoids, Meters, or LEDs
Frequency Doubling For Low Ripple
Tachometer Has Built-In Hysteresis With
Either Differential Input or Ground Referenced
Input
Built-In Zener on LM2917
±0.3% Linearity Typical
Ground Referenced Tachometer is Fully
Protected From Damage Due to Swings Above
VCC and Below Ground
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
Over/Under Speed Sensing
Frequency to Voltage Conversion
(Tachometer)
Speedometers
Breaker Point Dwell Meters
Hand-Held Tachometer
Speed Governors
Cruise Control
Automotive Door Lock Control
Clutch Control
Horn Control
Touch or Sound Switches
The op amp/comparator is fully compatible with the
tachometer and has a floating transistor as its output.
This feature allows either a ground or supply referred
load of up to 50 mA. The collector may be taken
above VCC up to a maximum VCE of 28V.
The two basic configurations offered include an 8-pin
device with a ground referenced tachometer input
and an internal connection between the tachometer
output and the op amp non-inverting input. This
version is well suited for single speed or frequency
switching or fully buffered frequency to voltage
conversion applications.
The more versatile configurations provide differential
tachometer input and uncommitted op amp inputs.
With this version the tachometer input may be floated
and the op amp becomes suitable for active filter
conditioning of the tachometer output.
Both of these configurations are available with an
active shunt regulator connected across the power
leads. The regulator clamps the supply such that
stable frequency to voltage and frequency to current
operations are possible with any supply voltage and a
suitable resistor.
ADVANTAGES
•
•
•
•
Output Swings to Ground For Zero Frequency
Input
Easy to Use; VOUT = fIN × VCC × R1 × C1
Only One RC Network provides Frequency
Doubling
Zener Regulator on Chip allows Accurate and
Stable Frequency to Voltage or Current
Conversion (LM2917)
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2000–2013, Texas Instruments Incorporated
LM2907-N, LM2917-N
SNAS555C – JUNE 2000 – REVISED MARCH 2013
www.ti.com
CONNECTION DIAGRAMS
PDIP and SOIC Packages, Top Views
2
Figure 1. See Package Number D0008A or P0008E
Figure 2. See Package Number D0008A or P0008E
Figure 3. See Package Number D0014A or
NFF0014A
Figure 4. See Package Number D0014A or
NFF0014A
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
LM2907-N, LM2917-N
www.ti.com
SNAS555C – JUNE 2000 – REVISED MARCH 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS (1) (2)
Supply Voltage
28V
Supply Current (Zener Options)
25 mA
Collector Voltage
28V
Differential Input Voltage
Tachometer
28V
Op Amp/Comparator
Input Voltage Range
28V
Tachometer
LM2907-8, LM2917-8
±28V
LM2907, LM2917
0.0V to +28V
Op Amp/Comparator
Power Dissipation
0.0V to +28V
LM2907-8, LM2917-8
LM2907-14, LM2917-14
1200 mW
(1)
1580 mW
−40°C to +85°C
Operating Temperature Range
−65°C to +150°C
Storage Temperature Range
Soldering Information
(1)
(2)
PDIP Package
Soldering (10 seconds)
260°C
SOIC Package
Vapor Phase (60 seconds)
215°C
Infrared (15 seconds)
220°C
For operation in ambient temperatures above 25°C, the device must be derated based on a 150°C maximum junction temperature and a
thermal resistance of 101°C/W junction to ambient for LM2907-8 and LM2917-8, and 79°C/W junction to ambient for LM2907-14 and
LM2917-14.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
ELECTRICAL CHARACTERISTICS
VCC = 12 VDC, TA = 25°C, see test circuit
Symbol
Parameter
Conditions
Min
Typ
Max
Units
±10
±25
±40
mV
TACHOMETER
Input Thresholds
VIN = 250 mVp-p @ 1 kHz (1)
(1)
Hysteresis
VIN = 250 mVp-p @ 1 kHz
Offset Voltage
VIN = 250 mVp-p @ 1 kHz (1)
30
LM2907/LM2917
LM2907-8/LM2917-8
mV
3.5
10
mV
5
15
mV
Input Bias Current
VIN = ±50 mVDC
0.1
1
μA
Pin 2
VIN = +125 mVDC (2)
8.3
VOL
Pin 2
VIN = −125 mVDC
(2)
I2, I3
Output Current
V2 = V3 = 6.0V (3)
I3
Leakage Current
I2 = 0, V3 = 0
K
Gain Constant
Linearity
VOH
V
2.3
V
240
μA
0.1
μA
140
180
See (2)
0.9
1.0
1.1
fIN = 1 kHz, 5 kHz, 10 kHz (4)
−1.0
0.3
+1.0
%
3
10
mV
500
nA
VCC−1.5V
V
OP/AMP COMPARATOR
VOS
VIN = 6.0V
IBIAS
VIN = 6.0V
Input Common-Mode
Voltage
(1)
(2)
(3)
(4)
50
0
Hysteresis is the sum +VTH − (−VTH), offset voltage is their difference. See test circuit.
VOH is equal to ¾ × VCC − 1 VBE, VOL is equal to ¼ × VCC − 1 VBE therefore VOH − VOL = VCC/2. The difference, VOH − VOL, and the
mirror gain, I2/I3, are the two factors that cause the tachometer gain constant to vary from 1.0.
Be sure when choosing the time constant R1 × C1 that R1 is such that the maximum anticipated output voltage at pin 3 can be reached
with I3 × R1. The maximum value for R1 is limited by the output resistance of pin 3 which is greater than 10 MΩ typically.
Nonlinearity is defined as the deviation of VOUT (@ pin 3) for fIN = 5 kHz from a straight line defined by the VOUT @ 1 kHz and VOUT @
10 kHz. C1 = 1000 pF, R1 = 68k and C2 = 0.22 mFd.
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
Submit Documentation Feedback
3
LM2907-N, LM2917-N
SNAS555C – JUNE 2000 – REVISED MARCH 2013
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
VCC = 12 VDC, TA = 25°C, see test circuit
Symbol
Parameter
Conditions
Min
Voltage Gain
40
Typ
Max
Units
200
V/mV
50
mA
Output Sink Current
VC = 1.0
Output Source Current
VE = VCC −2.0
10
Saturation Voltage
ISINK = 5 mA
0.1
ISINK = 20 mA
ISINK = 50 mA
1.0
RDROP = 470Ω
7.56
mA
0.5
V
1.0
V
1.5
V
15
Ω
ZENER REGULATOR
Regulator Voltage
Series Resistance
10.5
Temperature Stability
+1
Total Supply Current
3.8
V
mV/°C
6
mA
TEST CIRCUIT AND WAVEFORM
Figure 5.
4
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
LM2907-N, LM2917-N
www.ti.com
SNAS555C – JUNE 2000 – REVISED MARCH 2013
Tachometer Input Threshold Measurement
Figure 6.
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
Submit Documentation Feedback
5
LM2907-N, LM2917-N
SNAS555C – JUNE 2000 – REVISED MARCH 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS
6
Tachometer Linearity vs Temperature
Tachometer Linearity vs Temperature
Figure 7.
Figure 8.
Total Supply Current
Zener Voltage vs Temperature
Figure 9.
Figure 10.
Normalized Tachometer Output (K) vs Temperature
Normalized Tachometer Output (K) vs Temperature
Figure 11.
Figure 12.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
LM2907-N, LM2917-N
www.ti.com
SNAS555C – JUNE 2000 – REVISED MARCH 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Tachometer Currents I2and I3 vs Supply Voltage
Tachometer Currents I2and I3 vs Temperature
Figure 13.
Figure 14.
Tachometer Linearity vs R1
Tachometer Input Hysteresis vs Temperature
Figure 15.
Figure 16.
Op Amp Output Transistor Characteristics
Op Amp Output Transistor Characteristics
Figure 17.
Figure 18.
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
Submit Documentation Feedback
7
LM2907-N, LM2917-N
SNAS555C – JUNE 2000 – REVISED MARCH 2013
www.ti.com
APPLICATIONS INFORMATION
The LM2907 series of tachometer circuits is designed for minimum external part count applications and
maximum versatility. In order to fully exploit its features and advantages let's examine its theory of operation. The
first stage of operation is a differential amplifier driving a positive feedback flip-flop circuit. The input threshold
voltage is the amount of differential input voltage at which the output of this stage changes state. Two options
(LM2907-8, LM2917-8) have one input internally grounded so that an input signal must swing above and below
ground and exceed the input thresholds to produce an output. This is offered specifically for magnetic variable
reluctance pickups which typically provide a single-ended ac output. This single input is also fully protected
against voltage swings to ±28V, which are easily attained with these types of pickups.
The differential input options (LM2907, LM2917) give the user the option of setting his own input switching level
and still have the hysteresis around that level for excellent noise rejection in any application. Of course in order
to allow the inputs to attain common-mode voltages above ground, input protection is removed and neither input
should be taken outside the limits of the supply voltage being used. It is very important that an input not go below
ground without some resistance in its lead to limit the current that will then flow in the epi-substrate diode.
Following the input stage is the charge pump where the input frequency is converted to a dc voltage. To do this
requires one timing capacitor, one output resistor, and an integrating or filter capacitor. When the input stage
changes state (due to a suitable zero crossing or differential voltage on the input) the timing capacitor is either
charged or discharged linearly between two voltages whose difference is VCC/2. Then in one half cycle of the
input frequency or a time equal to 1/2 fIN the change in charge on the timing capacitor is equal to VCC/2 × C1.
The average amount of current pumped into or out of the capacitor then is:
(1)
The output circuit mirrors this current very accurately into the load resistor R1, connected to ground, such that if
the pulses of current are integrated with a filter capacitor, then VO = ic × R1, and the total conversion equation
becomes:
VO = VCC × fIN × C1 × R1 × K
where
•
K is the gain constant—typically 1.0
(2)
The size of C2 is dependent only on the amount of ripple voltage allowable and the required response time.
CHOOSING R1 AND C1
There are some limitations on the choice of R1 and C1 which should be considered for optimum performance.
The timing capacitor also provides internal compensation for the charge pump and should be kept larger than
500 pF for very accurate operation. Smaller values can cause an error current on R1, especially at low
temperatures. Several considerations must be met when choosing R1. The output current at pin 3 is internally
fixed and therefore VO/R1 must be less than or equal to this value. If R1 is too large, it can become a significant
fraction of the output impedance at pin 3 which degrades linearity. Also output ripple voltage must be considered
and the size of C2 is affected by R1. An expression that describes the ripple content on pin 3 for a single R1C2
combination is:
(3)
It appears R1 can be chosen independent of ripple, however response time, or the time it takes VOUT to stabilize
at a new voltage increases as the size of C2 increases, so a compromise between ripple, response time, and
linearity must be chosen carefully.
As a final consideration, the maximum attainable input frequency is determined by VCC, C1 and I2:
(4)
8
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
LM2907-N, LM2917-N
www.ti.com
SNAS555C – JUNE 2000 – REVISED MARCH 2013
USING ZENER REGULATED OPTIONS (LM2917)
For those applications where an output voltage or current must be obtained independent of supply voltage
variations, the LM2917 is offered. The most important consideration in choosing a dropping resistor from the
unregulated supply to the device is that the tachometer and op amp circuitry alone require about 3 mA at the
voltage level provided by the zener. At low supply voltages there must be some current flowing in the resistor
above the 3 mA circuit current to operate the regulator. As an example, if the raw supply varies from 9V to 16V, a
resistance of 470Ω will minimize the zener voltage variation to 160 mV. If the resistance goes under 400Ω or
over 600Ω the zener variation quickly rises above 200 mV for the same input variation.
TYPICAL APPLICATIONS
Figure 19. Minimum Component Tachometer
Figure 20. ”Speed Switch”, Load is Energized when fIN ≥ (1 / ( 2RC))
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
Submit Documentation Feedback
9
LM2907-N, LM2917-N
SNAS555C – JUNE 2000 – REVISED MARCH 2013
www.ti.com
Figure 21. Zener Regulated Frequency to Voltage Converter
Figure 22. Breaker Point Dwell Meter
10
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
LM2907-N, LM2917-N
www.ti.com
SNAS555C – JUNE 2000 – REVISED MARCH 2013
Figure 23. Voltage Driven Meter Indicating Engine RPM
VO = 6V @ 400 Hz or 6000 ERPM (8 Cylinder Engine)
Figure 24. Current Driven Meter Indicating Engine RPM
IO = 10 mA @ 300 Hz or 6000 ERPM (6 Cylinder Engine)
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
Submit Documentation Feedback
11
LM2907-N, LM2917-N
SNAS555C – JUNE 2000 – REVISED MARCH 2013
www.ti.com
Figure 25. Capacitance Meter
VOUT = 1V–10V for CX = 0.01 to 0.1 mFd (R = 111k)
Figure 26. Two-Wire Remote Speed Switch
12
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
LM2907-N, LM2917-N
www.ti.com
SNAS555C – JUNE 2000 – REVISED MARCH 2013
Figure 27. 100 Cycle Delay Switch
Variable Reluctance Magnetic Pickup Buffer Circuits
Precision two-shot output frequency
equals twice input frequency.
Pulse height = VZENER
Figure 28.
Figure 29.
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
Submit Documentation Feedback
13
LM2907-N, LM2917-N
SNAS555C – JUNE 2000 – REVISED MARCH 2013
www.ti.com
Finger Touch or Contact Switch
Figure 30.
Figure 31.
Flashing begins when fIN ≥ 100 Hz.
Flash rate increases with input frequency
increase beyond trip point.
Figure 32. Flashing LED Indicates Overspeed
14
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
LM2907-N, LM2917-N
www.ti.com
SNAS555C – JUNE 2000 – REVISED MARCH 2013
Figure 33. Frequency to Voltage Converter with 2 Pole Butterworth Filter to Reduce Ripple
Figure 34. Overspeed Latch
Figure 36.
Figure 35.
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
Submit Documentation Feedback
15
LM2907-N, LM2917-N
SNAS555C – JUNE 2000 – REVISED MARCH 2013
www.ti.com
Frequency Switch Applications
Some frequency switch applications may require hysteresis in the comparator function which can be
implemented in several ways.
Figure 37.
16
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
LM2907-N, LM2917-N
www.ti.com
SNAS555C – JUNE 2000 – REVISED MARCH 2013
Figure 38.
Figure 39.
Figure 40.
Figure 41.
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
Submit Documentation Feedback
17
LM2907-N, LM2917-N
SNAS555C – JUNE 2000 – REVISED MARCH 2013
www.ti.com
Changing the Output Voltage for an Input Frequency of Zero
Figure 42.
Figure 43.
Changing Tachometer Gain Curve or Clamping the Minimum Output Voltage
Figure 44.
18
Submit Documentation Feedback
Figure 45.
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
LM2907-N, LM2917-N
www.ti.com
SNAS555C – JUNE 2000 – REVISED MARCH 2013
ANTI-SKID CIRCUIT FUNCTIONS
“Select-Low” Circuit
VOUT Proportional to the Lower
of the Two Input Wheel Speeds
Figure 46.
Figure 47.
“Select-High” Circuit
VOUT Proportional to the Higher
of the Two Input Wheel Speeds
Figure 48.
Figure 49.
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
Submit Documentation Feedback
19
LM2907-N, LM2917-N
SNAS555C – JUNE 2000 – REVISED MARCH 2013
www.ti.com
“Select-Average” Circuit
Figure 50.
20
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
LM2907-N, LM2917-N
www.ti.com
SNAS555C – JUNE 2000 – REVISED MARCH 2013
EQUIVALENT SCHEMATIC DIAGRAM
*This connection made on LM2907-8 and LM2917-8 only.
**This connection made on LM2917 and LM2917-8 only.
Figure 51.
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
Submit Documentation Feedback
21
LM2907-N, LM2917-N
SNAS555C – JUNE 2000 – REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision B (March 2013) to Revision C
•
22
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 21
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2907-N LM2917-N
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM2907M
NRND
SOIC
D
14
55
TBD
Call TI
Call TI
-40 to 85
LM2907M
LM2907M-8
NRND
SOIC
D
8
95
TBD
Call TI
Call TI
-40 to 85
LM29
07M-8
LM2907M-8/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
-40 to 85
LM29
07M-8
LM2907M/NOPB
ACTIVE
SOIC
D
14
55
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
-40 to 85
LM2907M
LM2907MX
NRND
SOIC
D
14
2500
TBD
Call TI
Call TI
-40 to 85
LM2907M
LM2907MX-8/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
-40 to 85
LM29
07M-8
LM2907MX/NOPB
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
-40 to 85
LM2907M
LM2907N
NRND
PDIP
NFF
14
25
TBD
Call TI
Call TI
-40 to 85
LM2907N
LM2907N-8
NRND
PDIP
P
8
40
TBD
Call TI
Call TI
-40 to 85
LM
2907N-8
LM2907N-8/NOPB
ACTIVE
PDIP
P
8
40
Green (RoHS
& no Sb/Br)
CU SN | Call TI
Level-1-NA-UNLIM
-40 to 85
LM
2907N-8
LM2907N/NOPB
ACTIVE
PDIP
NFF
14
25
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 85
LM2907N
LM2917M
NRND
SOIC
D
14
55
TBD
Call TI
Call TI
-40 to 85
LM2917M
LM2917M-8
NRND
SOIC
D
8
95
TBD
Call TI
Call TI
-40 to 85
LM29
17M-8
LM2917M-8/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
LM29
17M-8
LM2917M/NOPB
ACTIVE
SOIC
D
14
55
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
-40 to 85
LM2917M
LM2917MX-8
NRND
SOIC
D
8
2500
TBD
Call TI
Call TI
-40 to 85
LM29
17M-8
LM2917MX-8/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
LM29
17M-8
LM2917MX/NOPB
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
-40 to 85
LM2917M
LM2917N
NRND
PDIP
NFF
14
25
TBD
Call TI
Call TI
-40 to 85
LM2917N
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM2917N-8
NRND
PDIP
P
8
40
TBD
Call TI
Call TI
-40 to 85
LM
2917N-8
LM2917N-8/NOPB
ACTIVE
PDIP
P
8
40
Green (RoHS
& no Sb/Br)
CU SN | Call TI
Level-1-NA-UNLIM
-40 to 85
LM
2917N-8
LM2917N/NOPB
ACTIVE
PDIP
NFF
14
25
Green (RoHS
& no Sb/Br)
CU SN | Call TI
Level-1-NA-UNLIM
-40 to 85
LM2917N
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
LM2907MX
SOIC
D
LM2907MX-8/NOPB
SOIC
LM2907MX/NOPB
SOIC
LM2917MX-8
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
9.35
2.3
8.0
16.0
Q1
14
2500
330.0
16.4
6.5
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
D
14
2500
330.0
16.4
6.5
9.35
2.3
8.0
16.0
Q1
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM2917MX-8/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM2917MX/NOPB
SOIC
D
14
2500
330.0
16.4
6.5
9.35
2.3
8.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM2907MX
SOIC
D
14
2500
367.0
367.0
35.0
LM2907MX-8/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
LM2907MX/NOPB
SOIC
D
14
2500
367.0
367.0
35.0
LM2917MX-8
SOIC
D
8
2500
367.0
367.0
35.0
LM2917MX-8/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
LM2917MX/NOPB
SOIC
D
14
2500
367.0
367.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
NFF0014A
N0014A
N14A (Rev G)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Similar pages