MSA-0505 Cascadable Silicon Bipolar MMIC Amplifier Data Sheet Description Features The MSA-0505 is a high performance medium power silicon bipolar Monolithic Microwave Integrated Circuit (MMIC) housed in a low cost, surface mount package. This MMIC is designed for use as a general purpose 50Ω gain block. Typical applications include narrow and broad band IF and RF amplifiers in commercial systems. • Cascadable 50 Ω Gain Block The MSA-series is fabricated using Avago’s 10 GHz fT, 25 GHz fMAX, silicon bipolar MMIC process which uses nitride self-alignment, ion implantation, and gold metallization to achieve excellent performance, uniformity and reliability. The use of an external bias resistor for temperature and current stability also allows bias flexibility. 05 Plastic Package • High Output Power: 18.0 dBm Typical P1 dB at 1.0 GHz • Low Distortion: 29.0 dBm Typical IP3 at 1.0 GHz • 7.0 dB Typical Gain at 1.0 GHz • Surface Mount Plastic Package • Tape-and-Reel Packaging Option Available • Lead-free Option Available Typical Biasing Configuration R bias VCC > 12 V RFC (Optional) 4 C block IN C block 3 1 OUT MSA 2 Vd = 8.4 V MSA-0505 Absolute Maximum Ratings Parameter Absolute Maximum[1] Device Current 135 mA [2,3] Power Dissipation 1.5 W RF Input Power +25 dBm Junction Temperature200°C Storage Temperature –65 to 150°C Thermal Resistance[2]: θjc = 85°C/W Notes: 1. Permanent damage may occur if any of these limits are exceeded. 2. TCASE = 25°C. 3. Derate at 11.8 mW/°C for TC > 73°C. Electrical Specifications[1], TA = 25°C Symbol Parameters and Test Conditions: Id = 80 mA, ZO = 50 Ω Units Min. Typ. P1 dB Output Power at 1 dB Gain Compression f = 0.5 GHz dBm 19.0 f = 1.0 GHz dBm 16.0 18.0 GP Power Gain (|S21| 2) f = 0.5 GHz dB 7.5 f = 1.0 GHz 6.0 7.0 ∆GP Gain Flatness f = 0.1 to 1.5 GHz dB ±0.75 f3 dB 3 dB Bandwidth[2] GHz2.3 Input VSWR f = 0.1 to 1.5 GHz 1.6:1 VSWR Output VSWR f = 0.1 to 1.5 GHz2.0:1 IP3 Third Order Intercept Point f = 1.0 GHz dBm29.0 NF 50 Ω Noise Figure f = 1.0 GHz dB 6.5 tD Group Delay f = 1.0 GHz psec 190 Vd Device Voltage V 6.7 8.4 dV/dT Device Voltage Temperature Coefficient mV/°C –16.0 Notes: 1. The recommended operating current range for this device is 60 to 100 mA. Typical performance as a function of current is on the following page. 2. Referenced from 0.1 GHz Gain (GP). Ordering Information Part Numbers MSA-0505-STR MSA-0505-STRG MSA-0505-TR1 MSA-0505-TR1G No. of Devices 10 100 500 500 Comments Bulk Bulk 7" Reel 7" Reel Note: Order part number with a “G” suffix if lead-free option is desired. Max. 10.1 MSA-0505 Typical Scattering Parameters (TA = 25°C, Id = 80 mA) S11 S21 Mag Freq. MHz Mag Ang 5 25 50 100 200 400 600 800 1000 1500 2000 2500 3000 .56 .24 .15 .13 .12 .12 .13 .13 .14 .21 .30 .40 .52 –39 14.9 5.56 –103 9.7 3.05 –130 8.22.57 –155 7.82.45 –170 7.7 3.43 178 7.52.37 172 7.42.34 168 7.22.29 166 7.02.24 159 6.42.09 148 5.2 1.82 136 4.1 1.60 1212.7 1.36 dB Ang 161 156 163 165 161 148 134 119 105 72 42 17 –7 dB S1 Mag Ang Mag S22 Ang k –18.5 –13.9 –13.7 –13.7 –13.5 –13.6 –13.6 –13.6 –13.4 –13.3 –13.1 –12.9 –12.6 .120 .202 .207 .207 .211 .209 .209 .209 .213 .217 .222 .227 .234 39 12 7 3 1 –1 –2 –3 –4 –6 –9 –11 –16 .65 .25 .15 .11 .11 .14 .17 .21 .25 .34 .42 .48 .55 –36 –90 –116 –132 –145 –146 –151 –157 –164 176 159 146 133 0.60 0.97 1.15 1.21 1.21 1.23 1.23 1.23 1.21 1.16 1.12 1.05 0.92 Typical Performance, TA = 25°C (unless otherwise noted) 10 120 90 P1 dB (dBm) 0.5 GHz 4 60 1.0 GHz 1.5 GHz 2.0 GHz 2 0 8 10 12 14 16 18 20 22 0 24 0 3 9 12 IP3 (dBm) 30 IP3 26 8 22 P1 dB (dBm) 6 4 2 0 0.1 0.5 1.0 5.0 FREQUENCY (GHz) Figure 4. Gain vs. Frequency, Id = 80 to 100 mA. 18 14 60 P1 dB 70 80 2.0 GHz 0 +25 +85 Figure 3. Output Power at 1 dB Gain Compression, vs. Case Temperature, Id = 80 mA. 34 10 12 –25 TEMPERATURE (C) Figure 2. Device Current vs. Voltage. 12 Gp (dB) 6 Vd (V) 14 .05 1.0 GHz 16 14 Figure 1. Typical Gain vs. Power Out, TA = 25°C, Id = 80 mA. .01 0.5 GHz 18 30 POWER OUT (dBm) 20 0.1 GHz 6 Id (mA) GAIN (dB) 8 22 TC = +85C TC = +25C TC = –25C 90 100 Id (mA) Figure 5. Output Power at 1 dB Gain Compression, Third Order Intercept vs. Case Temperature, f = 1.0 GHz. 05 Plastic Package Dimensions GROUND 4 0.030 DIA 0.76 0.030 0.89 RF OUTPUT AND DC BIAS RF INPUT 5 3 1 0.030 ± 0.010 0.76 ± 0.25 (4 PLCS) GROUND 0.135 ± 0.015 3.42 ± 0.25 (4 PLCS) 0.020 0.51 0.145 3.68 0.008 ± 0.002 0.20 ± 0.05 0.030 0.76 0.050 1.27 0.100 ± 0.010 2.54 ± 0.25 Notes: (unless otherwise specified) 1. Dimensions are in 2. Tolerances in .xxx = 0.005 mm .xx = 0.13 2 0.0005 ± 0.010 (0.013 ± 0.25) mm For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. Copyright © 2008 Avago Technologies, Limited. All rights reserved. Obsoletes 5989-2754EN AV02-1227EN May 14, 2008