TC74VCX162721FT TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74VCX162721FT Low-Voltage 20-Bit D-Type Flip-Flop with 3.6-V Tolerant Inputs and Outputs The TC74VCX162721FT is a high-performance CMOS 20-bit D-type flip-flop. Designed for use in 1.8-V, 2.5-V or 3.3-V systems, it achieves high-speed operation while maintaining the CMOS low power dissipation. It is also designed with overvoltage tolerant inputs and outputs up to 3.6 V. The TC74VCX162721FT is an edge-triggered D-type flip-flop with qualified clock storage. On the positive transition of the clock (CK) input, the device provides true data at the Q outputs if the clock-enable (CKEN) input is low. If CKEN is high, no data is Weight: 0.25 g (typ.) stored. When the OE input is high, the outputs are in a high-impedance state. This device is designed to be used with 3-state memory address drivers, etc. The 26-Ω series resistor helps reducing output overshoot and undershoot without external resistor. All inputs are equipped with protection circuits against static discharge. Features • 26-Ω series resistors on outputs • Low-voltage operation: VCC = 1.8 to 3.6 V • High-speed operation : tpd = 4.4 ns (max) (VCC = 3.0 to 3.6 V) : tpd = 5.8 ns (max) (VCC = 2.3 to 2.7 V) : tpd = 9.8 ns (max) (VCC = 1.8 V) • Output current : IOH/IOL = ±12 mA (min) (VCC = 3.0 V) : IOH/IOL = ±8 mA (min) (VCC = 2.3 V) : IOH/IOL = ±4 mA (min) (VCC = 1.8 V) • Latch-up performance: −300 mA • ESD performance: Machine model ≥ ±200 V Human body model ≥ ±2000 V • Package: TSSOP • 3.6-V tolerant function and power-down protection provided on all inputs and outputs 1 2007-10-19 TC74VCX162721FT Pin Assignment (top view) IEC Logic Symbol OE 1 56 CK Q1 2 55 D1 Q2 3 54 D2 1OE CK CKEN GND 4 53 GND Q3 5 52 D3 Q4 6 51 D4 VCC 7 50 D1 D2 D3 D4 VCC Q5 8 49 D5 Q6 9 48 D6 D5 D6 D7 D8 D9 Q7 10 47 D7 GND 11 46 GND D11 Q8 12 45 D8 D13 Q9 13 44 D10 D12 D14 D9 D15 14 43 D10 D16 D17 Q11 15 42 D11 D18 Q10 Q12 16 41 D12 Q13 17 40 D13 GND 18 39 GND Q14 19 38 D14 20 37 D15 Q16 21 36 D16 Q15 VCC 22 35 VCC Q17 23 34 D17 Q18 24 33 D18 GND 25 32 GND Q19 26 31 D19 Q20 27 30 D20 NC 28 29 CKEN D19 D20 2 1 56 29 55 54 EN2 C1 1C 1D 2 3 52 5 51 6 49 8 48 9 47 10 45 12 44 43 13 14 42 15 41 16 40 17 38 19 37 20 36 21 34 33 23 24 31 26 30 27 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15 Q16 Q17 Q18 Q19 Q20 2007-10-19 TC74VCX162721FT Truth Table (each flip-flop) Inputs Outputs Q OE CKEN CK D L H X X Qn L L H H L L L L L L L or H X Qn H X X X Z X: Don’t care Z: High impedance Qn: No change System Diagram OE CKEN CK D1 1 29 CK 56 55 D Q 2 Q1 To 19 other channels 3 2007-10-19 TC74VCX162721FT Absolute Maximum Ratings (Note 1) Characteristics Symbol Rating Unit Power supply voltage VCC −0.5 to 4.6 V DC input voltage VIN −0.5 to 4.6 V −0.5 to 4.6 (Note 2) DC output voltage VOUT −0.5 to VCC + 0.5 V (Note 3) Input diode current −50 IIK mA Output diode current IOK ±50 DC output current IOUT ±50 mA Power dissipation DC VCC/ground current per supply pin Storage temperature (Note 4) mA PD 400 mW ICC/IGND ±100 mA Tstg −65 to 150 °C Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 2: OFF state Note 3: High or low state. IOUT absolute maximum rating must be observed. Note 4: VOUT < GND, VOUT > VCC Operating Ranges (Note 1) Characteristics Symbol Power supply voltage VCC Input voltage VIN Output voltage Output current Rating Unit 1.8 to 3.6 1.2 to 3.6 (Note 2) −0.3 to 3.6 V 0 to 3.6 (Note 3) VOUT 0 to VCC (Note 4) IOH/IOL ±12 (Note 5) ±8 (Note 6) ±4 (Note 7) Operating temperature Topr −40 to 85 Input rise and fall time dt/dv 0 to 10 V V mA °C (Note 8) ns/V Note 1: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. Note 2: Data retention only Note 3: OFF state Note 4: High or low state Note 5: VCC = 3.0 to 3.6 V Note 6: VCC = 2.3 to 2.7 V Note 7: VCC = 1.8 V Note 8: VIN = 0.8 to 2.0 V, VCC = 3.0 V 4 2007-10-19 TC74VCX162721FT Electrical Characteristics DC Characteristics (Ta = −40 to 85°C, 2.7 V < VCC =< 3.6 V) Characteristics Input voltage Symbol Test Condition H-level VIH ⎯ L-level VIL ⎯ Min Max 2.7 to 3.6 2.0 ⎯ 2.7 to 3.6 ⎯ 0.8 2.7 to 3.6 VCC − 0.2 ⎯ IOH = −6 mA 2.7 2.2 ⎯ IOH = −8 mA 3.0 2.4 ⎯ IOH = −12 mA 3.0 2.2 ⎯ IOL = 100 μA IOH = −100 μA H-level VOH VIN = VIH or VIL Output voltage L-level VOL Input leakage current IIN 3-state output OFF state current IOZ Power-off leakage current IOFF Quiescent supply current ICC Increase in ICC per input ΔICC VCC (V) Unit V V 2.7 to 3.6 ⎯ 0.2 IOL = 6 mA 2.7 ⎯ 0.4 IOL = 8 mA 3.0 ⎯ 0.55 IOL = 12 mA 3.0 ⎯ 0.8 2.7 to 3.6 ⎯ ±5.0 μA 2.7 to 3.6 ⎯ ±10.0 μA 0 ⎯ 10.0 μA VIN = VCC or GND 2.7 to 3.6 ⎯ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 2.7 to 3.6 ⎯ ±20.0 VIH = VCC − 0.6 V 2.7 to 3.6 ⎯ 750 Min Max VIN = VIH or VIL VIN = 0 to 3.6 V VIN = VIH or VIL VOUT = 0 to 3.6 V VIN, VOUT = 0 to 3.6 V μA DC Characteristics (Ta = −40 to 85°C, 2.3 V =< VCC =< 2.7 V) Characteristics Input voltage Symbol Test Condition H-level VIH ⎯ 2.3 to 2.7 1.6 ⎯ L-level VIL ⎯ 2.3 to 2.7 ⎯ 0.7 2.3 to 2.7 VCC − 0.2 ⎯ IOH = −4 mA 2.3 2.0 ⎯ IOH = −6 mA 2.3 1.8 ⎯ IOH = −8 mA 2.3 1.7 ⎯ IOL = 100 μA 2.3 to 2.7 ⎯ 0.2 IOL = 6 mA 2.3 ⎯ 0.4 IOL = 8 mA 2.3 ⎯ 0.6 2.3 to 2.7 ⎯ ±5.0 μA 2.3 to 2.7 ⎯ ±10.0 μA 0 ⎯ 10.0 μA VIN = VCC or GND 2.3 to 2.7 ⎯ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 2.3 to 2.7 ⎯ ±20.0 IOH = −100 μA H-level VOH VIN = VIH or VIL Output voltage L-level VOL Input leakage current IIN 3-state output OFF state current IOZ Power-off leakage current IOFF Quiescent supply current ICC VIN = VIH or VIL VIN = 0 to 3.6 V VIN = VIH or VIL VOUT = 0 to 3.6 V VIN, VOUT = 0 to 3.6 V 5 VCC (V) Unit V V μA 2007-10-19 TC74VCX162721FT DC Characteristics (Ta = −40 to 85°C, 1.8 V =< VCC < 2.3 V) Characteristics Symbol Test Condition H-level VIH ⎯ L-level VIL ⎯ H-level VOH Min Max 1.8 to 2.3 0.7 × VCC ⎯ 1.8 to 2.3 ⎯ 0.2 × VCC IOH = −100 μA 1.8 VCC − 0.2 ⎯ IOH = −4 mA 1.8 1.4 ⎯ IOL = 100 μA 1.8 ⎯ 0.2 IOL = 4 mA 1.8 ⎯ 0.3 1.8 ⎯ ±5.0 μA 1.8 ⎯ ±10.0 μA 0 ⎯ 10.0 μA VIN = VCC or GND 1.8 ⎯ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 1.8 ⎯ ±20.0 VCC (V) Input voltage VIN = VIH or VIL Output voltage VOL VIN = VIH or VIL Input leakage current IIN VIN = 0 to 3.6 V 3-state output OFF state current IOZ Power-off leakage current IOFF Quiescent supply current ICC L-level VIN = VIH or VIL VOUT = 0 to 3.6 V VIN, VOUT = 0 to 3.6 V 6 Unit V V μA 2007-10-19 TC74VCX162721FT AC Characteristics (Ta = −40 to 85°C, input: tr = tf = 2.0 ns, CL = 30 pF, RL = 500 Ω) (Note 1) Characteristics Maximum clock frequency Symbol fmax Propagation delay time tpLH (CK-Q) tpHL 3-state output enable time 3-state output disable time tpZL tpZH tpLZ tpHZ Minimum pulse width tW (H) (CK) tW (L) Minimum setup time (D, CKEN ) Minimum hold time (D, CKEN ) Output to output skew ts th Test Condition Figure 1, Figure 2 Figure 1, Figure 2 Figure 1, Figure 3 Figure 1, Figure 3 Figure 1, Figure 2 Figure 1, Figure 2, Figure 4 tosHL Max 1.8 100 ⎯ 2.5 ± 0.2 200 ⎯ 3.3 ± 0.3 250 ⎯ 1.8 1.5 9.8 2.5 ± 0.2 0.8 5.8 3.3 ± 0.3 0.6 4.4 1.8 1.5 9.8 2.5 ± 0.2 0.8 5.9 3.3 ± 0.3 0.6 4.3 1.8 1.5 8.8 2.5 ± 0.2 0.8 4.9 3.3 ± 0.3 0.6 4.3 1.8 4.0 ⎯ 2.5 ± 0.2 1.5 ⎯ 3.3 ± 0.3 1.5 ⎯ 1.8 2.5 ⎯ 2.5 ± 0.2 1.5 ⎯ 3.3 ± 0.3 1.5 ⎯ 1.8 1.0 ⎯ 2.5 ± 0.2 1.0 ⎯ 3.3 ± 0.3 1.0 ⎯ 1.8 ⎯ 0.5 (Note 2) 2.5 ± 0.2 ⎯ 0.5 3.3 ± 0.3 ⎯ 0.5 Figure 1, Figure 2, Figure 4 tosLH Min VCC (V) Unit MHz ns ns ns ns ns ns ns Note 1: For CL = 50 pF, add approximately 300 ps to the AC maximum specification. Note 2: Parameter guaranteed by design. (tosLH = |tpLHm − tpLHn|, tosHL = |tpHLm − tpHLn|) 7 2007-10-19 TC74VCX162721FT Dynamic Switching Characteristics (Ta = 25°C, input: tr = tf = 2.0 ns, CL = 30 pF, RL = 500 Ω) Characteristics Test Condition Symbol Typ. Unit VCC (V) Quiet output maximum dynamic VOL Quiet output minimum dynamic VOL Quiet output minimum dynamic VOH Note: VOLP VOLV VOHV VIH = 1.8 V, VIL = 0 V (Note) 1.8 0.15 VIH = 2.5 V, VIL = 0 V (Note) 2.5 0.25 VIH = 3.3 V, VIL = 0 V (Note) 3.3 0.35 VIH = 1.8 V, VIL = 0 V (Note) 1.8 −0.15 VIH = 2.5 V, VIL = 0 V (Note) 2.5 −0.25 VIH = 3.3 V, VIL = 0 V (Note) 3.3 −0.35 VIH = 1.8 V, VIL = 0 V (Note) 1.8 1.55 VIH = 2.5 V, VIL = 0 V (Note) 2.5 2.05 VIH = 3.3 V, VIL = 0 V (Note) 3.3 2.65 V V V Parameter guaranteed by design. Capacitive Characteristics (Ta = 25°C) Symbol Test Condition Input capacitance CIN ⎯ Output capacitance CO ⎯ Power dissipation capacitance CPD Characteristics Note: Typ. Unit 1.8, 2.5, 3.3 6 pF 1.8, 2.5, 3.3 7 pF 1.8, 2.5, 3.3 60 pF VCC (V) fIN = 10 MHz (Note) CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD･VCC･fIN + ICC/20 (per bit) 8 2007-10-19 TC74VCX162721FT AC Test Circuit 6.0 V or VCC × 2 Open GND RL Switch Switch tpLH, tpHL Open RL Measure CL Output Parameter tpLZ, tpZL CL = 30 pF RL = 500 Ω 6.0 V VCC × 2 tpHZ, tpZH @VCC = 3.3 ± 0.3 V @VCC = 2.5 ± 0.2 V @VCC = 1.8 V GND Figure 1 AC Waveform tr 2.0 ns Input (CK) 10% tf 2.0 ns VIH 90% VM GND tr 2.0 ns Input (D) 10% tw (H) tw (L) VIH 90% VM ts (H) Output (Q) tf 2.0 ns th (H) ts (L) th (L) GND VOH VM tpHL tpLH VOL Figure 2 tpLH, tpHL, tw, ts, th 9 2007-10-19 TC74VCX162721FT tr 2.0 ns tf 2.0 ns 90% VM Output Enable ( OE ) VIH 10% tpLZ GND tpZL 3.0 V or VCC Output (Q) Low to Off to Low VM VX tpHZ VOH VY Output (Q) High to Off to High VOL tpZH VM GND Outputs enabled Outputs enabled Outputs disabled Figure 3 tpLZ, tpHZ, tpZL, tpZH tr 2.0 ns Input ( CKEN ) tf 2.0 ns VIH 90% VM 10% GND tr 2.0 ns VIH Output (CK) VM ts (H) th (H) ts (L) GND th (L) Figure 4 ts, th Symbol VCC 3.3 ± 0.3 V 2.5 ± 0.2 V 1.8 V VIH 2.7 V VCC VCC VM 1.5 V VCC/2 VCC/2 VX VOL + 0.3 V VOL + 0.15 V VOL + 0.15 V VY VOH − 0.3 V VOH − 0.15 V VOH − 0.15 V 10 2007-10-19 TC74VCX162721FT Package Dimensions Weight: 0.25 g (typ.) 11 2007-10-19 TC74VCX162721FT RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 12 2007-10-19