6116A: 11/8/89 Revision: Monday, November 8, 1993 CY6116A CY6117A Features Pin Configurations DIP/SOJ Top View A6 2 23 A8 A5 3 22 A9 A4 4 21 WE A3 5 25 WE OE A2 6 24 OE 19 A10 NC 7 23 A10 18 CE NC 8 22 NC 21 NC 8 17 I/O7 9 16 I/O6 10 I/O2 11 14 I/O4 GND 12 13 I/O3 15 27 NC A0 A0 I/O0 8 6117A 9 Commercial Military Commercial Military Cypress Semiconductor Corporation D 20 100 40/20 3901 North First Street 1 OE 24 A10 11 23 CE 12 22 I/O7 13 21 I/O6 10 I/O 1 Maximum Access Time (ns) Maximum Operating Current (mA) Maximum Standby Current (mA) 6116A-20 6117A-20 WE 25 14 15 16 17 1819 20 6116A-1 Selection Guide 26 6116A-25 6117A-25 25 100 125 20 40 D 6116A-35 6117A-35 San Jose 35 100 100 20 20 I/O 4 I/O 5 A1 V CC A9 7 NC A2 NC A8 28 NC A3 NC 29 A1 I/O7 1 32 31 30 6 A2 OE 2 A5 A3 DOWN DECODER 3 5 I/O 3 COLUMN 4 A6 A4 I/O6 POWER NC I/O5 WE 6116A-3 LCC Top View I/O4 CE I/O7 6116A-2 I/O3 A4 CE 19 1213 14 151617 18 GND A5 20 11 A7 ARRAY 10 NC 128 x 16 x 8 9 A0 I/O0 I/O5 I/O1 6116A I/O 6 A0 I/O0 2 1 28 27 26 A1 NC A6 6116A I/O 2 A7 7 I/O2 SENSE AMPS A8 ROW DECODER A9 A1 3 1 I/O 2 I/O1 A10 6 20 4 I/O I/O0 5 A2 A9 VCC A6 24 A5 1 A4 A7 A3 INPUT BUFFER LCC Top View V CC Logic Block Diagram A8 D D I/O 5 D A7 D The CY6116A and CY6117A are highĆ performance CMOS static RAMs orgaĆ nized as 2048 words by 8 bits. Easy memoryexpansionisprovidedbyanactive LOW chip enable (CE) and active LOW output enable (OE), and threeĆstate drivĆ ers. The CY6116A and CY6117A have an automatic powerĆdown feature, reducing the power consumption by 83% when deĆ selected. Writingtothedeviceisaccomplishedwhen the chip enable (CE) and write enable (WE) inputs are both LOW. Data on the I/Opins(I/O0 throughI/O7)iswritteninto Automatic powerĆdown when deselected CMOS for optimum speed/power High speed Ċ 20 ns Low active power Ċ 550 mW Low standby power Ċ 110 mW TTLĆcompatible inputs and outputs Capable of withstanding greater than 2001V electrostatic discharge I/O 3 I/O 4 D D the memory location specified on the adĆ dress pins (A0 through A10). ReadingthedeviceisaccomplishedbytakĆ ing chip enable (CE) and output enable (OE) LOW while write enable (WE) reĆ mainsHIGH.Undertheseconditions,the contents of the memory location specified on the address pins will appear on the I/O pins. The I/O pins remain in highĆimpedance state when chip enable (CE) is HIGH or write enable (WE) is LOW. The CY6116A and CY6117A utilize a die coat to insure alpha immunity. Functional Description GND D 2K x 8 Static RAM 6116A-45 6117A-45 45 100 100 20 20 6116A-4 6116A-55 6117A-55 55 80 100 20 20 D CA 95134 D 408-943-2600 February 1988 - Revised December 1992 6116A: 11/8/89 Revision: Monday, November 8, 1993 CY6116A CY6117A Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Static Discharge Voltage . . . . . . . . . . . . . . . . . . . . . . . >2001V (per MILĆSTDĆ883, Method 3015) Storage Temperature . . . . . . . . . . . . . . . . . . -65_C to +150_C LatchĆUp Current . . . . . . . . . . . . . . . . . . . . . . . . . . . >200 mA Ambient Temperature with Power Applied . . . . . . . . . . . . . . . . . . . . . . . -55_C to +125_C Operating Range Ambient Supply Voltage to Ground Potential (Pin 24 to Pin 12) . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V Range Commercial DC Voltage Applied to Outputs in High Z State . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V Military[1] Temperature VCC 0_C to +70_C 5V ± 10% -55_C to +125_C 5V ± 10% DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . -3.0V to +7.0V Output Current into Outputs (LOW) . . . . . . . . . . . . . . 20 mA Electrical Characteristics Parameter VOH Over the Operating Range[2] Description Test Conditions 6116A-20 6116A-25, 35, 45 6116A-55 6117A-20 6117A-25, 35, 45 6117A-55 Min. Max. Min. Max. Max. 2.4 VOL 0.4 V VIH Input HIGH Voltage 2.2 VCC 2.2 VCC 2.2 VCC V VIL Input LOW Voltage[3] -0.5 0.8 -0.5 0.8 -0.5 0.8 V IIX Input Load Current GND < VI < VCC -10 +10 -10 +10 -10 +10 IOZ Output Leakage Current GND < VI < VCC, Output Disabled -10 +10 -10 +10 -10 +10 mA mA IOS Output Short Circuit Current[4] VCC = Max., VOUT = GND -300 mA ICC VCC Operating p g S l Current C Supply VCC = Max. A IOUT = 0 mA f = fMAX = 1/tRC Com'l mA Automatic CE P PowerĆDown D Current C - TTL Inputs Max. VCC, CE > VIH f = fMAX Com'l Automatic CE PowerĆDown Current - CMOS Inputs Max. VCC, Com'l CE > VIH - 0.3V, VIN > VCC - 0.3V or VIN < 0.3V, Mil f=0 ISB2 0.4 2.4 Unit OutputHIGHVoltage VCC = Min., IOH = -4.0 mA Output LOW Voltage VCC = Min., IOL = 8.0 mA ISB1 2.4 Min. 0.4 V -300 -300 100 100 80 125 100 Mil 25 35, 45 100 40 Mil 25 35, 45, 55 20 20 40 20 mA 20 20 20 20 20 20 mA [5] Capacitance Parameter Description CIN Input Capacitance COUT Output Capacitance Test Conditions TA = 25_C, f = 1 MHz, VCC = 5.0V 5 0V Notes: 1. 2. 3. TA is the instant on" case temperature. See the last page of this specification for Group A subgroup testing inĆ formation. VIL (min.) = -3.0V for pulse durations less than 30 ns. 4. 5. 2 Max. Unit 10 pF 10 pF Not more than 1 output should be shorted at one time. Duration of the short circuit should not exceed 30 seconds. Tested initially and after any design or process changes that may affect these parameters. 6116A: 11/8/89 Revision: Monday, November 8, 1993 CY6116A CY6117A AC Test Loads and Waveforms R1 481W 5V OUTPUT 5V OUTPUT R2 255W 30 pF INCLUDING JIG AND SCOPE 5 pF INCLUDING JIG AND SCOPE (a) R1 481W 3.0V R2 255W GND 10% 5 ns ALL INPUT PULSES 90% 90% 10% 5 ns 6116A-5 (b) 6116A-6 Equivalent to: THÉVENIN EQUIVALENT 167W OUTPUT 1.73V Switching Characteristics Over the Operating Range[2, 6] 6116A-20 6117A-20 Parameter Description Min. 6116A-25 6117A-25 Max. Min. Max. 6116A-35 6117A-35 Min. Max. 6116A-45 6117A-45 Min. Max. 6116A-55 6117A-55 Min. Max. Unit READ CYCLE tRC Read Cycle Time tAA Address to Data Valid tOHA Data Hold from Address Change tACE CE LOW to Data Valid 20 25 35 45 55 ns tDOE OE LOW to Data Valid 10 12 15 20 25 ns tLZOE OE LOW to Low Z tHZOE 20 OE HIGH to High Z 20 5 3 [8] CE LOW to Low Z tHZCE CE HIGH to High Z[7, 8 ] tPU CE LOW to PowerĆUp tPD CE HIGH to PowerĆDown 35 25 5 [7] tLZCE WRITE CYCLE 25 35 5 3 8 5 8 0 20 20 5 0 20 ns 20 15 ns ns 20 0 25 ns ns 3 5 0 55 15 15 ns 5 3 5 0 45 12 10 55 5 3 10 5 45 ns ns 25 ns [9] tWC Write Cycle Time 20 20 25 40 50 ns tSCE CE LOW to Write End 15 20 25 30 40 ns tAW Address SetĆUp to Write End 15 20 25 30 40 ns tHA Address Hold from Write End 0 0 0 0 0 ns tSA Address SetĆUp to Write Start 0 0 0 0 0 ns tPWE WE Pulse Width 15 15 20 20 25 ns tSD Data SetĆUp to Write End 10 10 15 15 25 ns tHD Data Hold from Write End 0 0 0 0 0 ns tHZWE WE LOW to High Z tLZWE WE HIGH to Low Z 7 7 5 5 Notes: 6. Test conditions assume signal transition time of 5 ns or less, timing refĆ erence levels of 1.5V, input pulse levels of 0 to 3.0V, and output loading of the specified IOL/IOH and 30ĆpF load capacitance. 7. tHZOE, tHZCE, and tHZWE are specified with CL = 5 pF as in part (b) of AC Test Loads. Transition is measured ±500 mV from steady state voltage. 8. At any given temperature and voltage condition, tHZCE is less than tLZCE for any given device. 9. 3 10 5 15 5 20 5 ns ns The internal write time of the memory is defined by the overlap of CE LOW and WE LOW. Both signals must be LOW to initiate a write and either signal can terminate a write by going HIGH. The data input setĆ up and hold timing should be referenced to the rising edge of the signal that terminates the write. 6116A: 11/8/89 Revision: Monday, November 8, 1993 CY6116A CY6117A Switching Waveforms Read Cycle No. 1[10, 11] tRC ADDRESS DATA OUT tOHA PREVIOUS DATA VALID tAA DATA VALID 6116A-7 Read Cycle No. 2[10, 12] tRC CE tACE OE tHZOE tHZCE tDOE DATA OUT VCC SUPPLY CURRENT tLZOE HIGH IMPEDANCE tLZCE tPU 50% HIGH IMPEDANCE DATA VALID tPD 50% ICC ISB 6116A-8 Write Cycle No. 1 (WE Controlled)[9, 13] tWC ADDRESS tSCE CE tSA tAW WE tSD DATA VALID DATA IN tHZWE DATA I/O tHA tPWE DATA UNDEFINED tHD tLZWE HIGH IMPEDANCE 6116A-9 Notes: 10. WE is HIGH for read cycle. 11. Device is continuously selected. OE, CE = VIL. 12. Address valid prior to or coincident with CE transition LOW. 13. Data I/O pins enter highĆimpedance state, as shown, when OE is held LOW during write. 4 6116A: 11/8/89 Revision: Monday, November 8, 1993 CY6116A CY6117A Switching Waveforms (continued) Write Cycle No. 2 (CE Controlled)[9, 13, 14] tWC ADDRESS tSA tSCE CE tAW tHA tPWE WE tHD tSD DATAIN VALID DATA IN tHZWE HIGH IMPEDANCE DATA I/O DATA UNDEFINED 6116A-10 Note: 14. If CE goes HIGH simultaneously with WE HIGH, the output remains in a highĆimpedance state. NORMALIZED SUPPLY CURRENT vs. AMBIENT TEMPERATURE NORMALIZED SUPPLY CURRENT vs. SUPPLY VOLTAGE 1.2 SB 1.2 NORMALIZED I CC, I ICC 1.0 0.8 0.6 0.4 0.0 4.0 4.5 5.0 ICC 0.8 0.6 0.4 VCC = 5.0V VIN = 5.0V 0.2 ISB 0.2 1.0 5.5 ISB 0.0 -55 6.0 1.6 1.3 1.4 NORMALIZED tAA NORMALIZED tAA 1.4 1.2 TA = 25_C 1.0 0.9 5.0 5.5 SUPPLY VOLTAGE (V) 100 80 VCC = 5.0V 60 TA = 25_C 40 20 0 0.0 6.0 1.2 1.0 VCC = 5.0V 0.6 -55 1.0 2.0 3.0 4.0 OUTPUT VOLTAGE (V) OUTPUT SINK CURRENT vs. OUTPUT VOLTAGE 0.8 4.5 120 NORMALIZED ACCESS TIME vs. AMBIENT TEMPERATURE NORMALIZED ACCESS TIME vs. SUPPLY VOLTAGE 0.8 4.0 125 OUTPUT SOURCE CURRENT vs. OUTPUT VOLTAGE AMBIENT TEMPERATURE (_C) SUPPLY VOLTAGE (V) 1.1 25 OUTPUT SINK CURRENT (mA) NORMALIZED I CC, I SB 1.4 OUTPUT SOURCE CURRENT (mA) Typical DC and AC Characteristics 140 120 100 VCC = 5.0V TA = 25_C 80 60 40 20 0 25 125 AMBIENT TEMPERATURE (_C) 5 0.0 1.0 2.0 3.0 OUTPUT VOLTAGE (V) 4.0 6116A: 11/8/89 Revision: Monday, November 8, 1993 CY6116A CY6117A Typical DC and AC Characteristics (continued) TYPICAL POWERĆON CURRENT vs. SUPPLY VOLTAGE TYPICAL ACCESS TIME CHANGE vs. OUTPUT LOADING 3.0 30.0 2.5 25.0 NORMALIZED ICC vs. CYCLE TIME 1.4 2.0 1.5 1.0 20.0 15.0 10.0 0.5 0.0 VCC = 4.5V TA = 25_C 5.0 0.0 1.0 2.0 3.0 4.0 5.0 NORMALIZED I CC DELTA t AA (ns) NORMALIZED I PO VCC = 5.0V 0.0 SUPPLY VOLTAGE (V) TA = 25_C 1.3 VIN = 0.5V 1.2 1.1 1.0 0.9 0.8 0 200 400 600 800 1000 0 CAPACITANCE (pF) 10 20 CYCLE FREQUENCY (MHz) Ordering Information Speed (ns) Ordering Code Package Name Package Type Operating Range 20 CY6116A-20PC P11 28ĆLead (300ĆMil) Molded DIP Commercial 25 CY6116A-25PC P11 28ĆLead (300ĆMil) Molded DIP Commercial CY6116A-25DMB D12 24ĆLead (600ĆMil) CerDIP Military CY6116A-25LMB L64 28ĆSquare Leadless Chip Carrier CY6116A-35PC P11 28ĆLead (300ĆMil) Molded DIP Commercial CY6116A-35DMB D12 24ĆLead (600ĆMil) CerDIP Military CY6116A-35LMB L64 28ĆSquare Leadless Chip Carrier CY6116A-45PC P11 28ĆLead (300ĆMil) Molded DIP Commercial CY6116A-45DMB D12 24ĆLead (600ĆMil) CerDIP Military CY6116A-45LMB L64 28ĆSquare Leadless Chip Carrier CY6116A-55PC P11 28ĆLead (300ĆMil) Molded DIP Commercial CY6116A-55DMB D12 24ĆLead (600ĆMil) CerDIP Military CY6116A-55LMB L64 28ĆSquare Leadless Chip Carrier 35 45 55 Speed (ns) Ordering Code Package Name Package Type Operating Range 35 CY6117AĆ35LMB L55 32ĆPin Rectangular Leadless Chip Carrier Military 45 CY6117AĆ45LMB L55 32ĆPin Rectangular Leadless Chip Carrier Military 55 CY6117AĆ55LMB L55 32ĆPin Rectangular Leadless Chip Carrier Military 6 30 40 6116A: 11/8/89 Revision: Monday, November 8, 1993 CY6116A CY6117A MILITARY SPECIFICATIONS Group A Subgroup Testing DC Characteristics Parameter VOH VOL VIH VIL Max. IIX IOZ ICC ISB Subgroups 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 Switching Characteristics Parameter READ CYCLE tRC tAA tOHA tACE tDOE WRITE CYCLE tWC tSCE tAW tHA tSA tPWE tSD tHD Subgroups 7, 8, 9, 10, 11 7, 8, 9, 10, 11 7, 8, 9, 10, 11 7, 8, 9, 10, 11 7, 8, 9, 10, 11 7, 8, 9, 10, 11 7, 8, 9, 10, 11 7, 8, 9, 10, 11 7, 8, 9, 10, 11 7, 8, 9, 10, 11 7, 8, 9, 10, 11 7, 8, 9, 10, 11 7, 8, 9, 10, 11 Document #: 38-00105-B 7 6116A: 11/8/89 Revision: Monday, November 8, 1993 CY6116A CY6117A Package Diagrams 24ĆLead (600ĆMil) CerDIP D12 32ĆPin Rectangular Leadless Chip Carrier L55 MIL-STD-1835 D-3 Config. A MIL-STD-1835 C-12 28ĆSquare Leadless Chip Carrier L64 MIL-STD-1835 C-4 8 6116A: 11/8/89 Revision: Monday, November 8, 1993 CY6116A CY6117A Package Diagrams (continued) 24ĆLead (600ĆMil) Molded DIP P11 E Cypress Semiconductor Corporation, 1992. The information contained herein is subject to change without notice. Cypress Semiconductor Corporatio n assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor Corporation product. Nor does it convey or imply any license under pa tent or other rights. Cypress SemiconĆ ductor does not authorize its products for use as critical components in lifeĆsupport systems where a malfunction or failure of the product may reason ably be expected to result in significant 9 injury to the user. The inclusion of Cypress Semiconductor products in lifeĆsupport systems applications implies that the manufacturer assumes all risk of such use and in so doing indemnifies Cypress Semiconductor against all damages.