DIGITRON SEMICONDUCTORS MCR1906 SERIES SILICON CONTROLLED RECTIFIERS Available Non-RoHS (standard) or RoHS compliant (add PBF suffix). Available as “HR” (high reliability) screened per MIL-PRF-19500, JANTX level. Add “HR” suffix to base part number. MAXIMUM RATINGS (TJ = 100°C unless otherwise noted) Rating Peak reverse blocking voltage MCR1906-1 MCR1906-2 MCR1906-3 MCR1906-4 MCR1906-5 MCR1906-6 MCR1906-7 MCR1906-8 Symbol Value 25 50 100 200 300 400 500 600 VRRM Forward current RMS (all conduction angles) Peak forward surge current (1 cycle, 60 Hz, TJ = -40 to +100°C) Forward peak gate power Unit Volts IT(RMS) 1.6 Amps ITSM 15 Amps PGM 0.1 Watts PG(AV) 0.01 Watts Forward peak gate current IGM 0.1 Amps Forward peak gate voltage VGFM 6.0 Volts Reverse peak gate voltage VGRM 6.0 Volts TJ -65 to +100 °C Tstg -65 to +150 °C - +230 °C Forward average gate power Operating junction temperature range Storage temperature range Lead solder temperature (<1/16” from case, 10 sec. max.) ELECTRICAL CHARACTERISTICS (TC = 25°C unless otherwise noted, RGK = 1000Ω) Characteristic Symbol Min Max 25 50 100 200 300 400 500 600 - IDRM - 500 Peak reverse blocking current (Rated VRRM @ TJ = 100°C) IRRM - 500 µA Forward “on” voltage (ITM = 1.0A peak) VTM - 1.75 Volts Gate trigger current (continuous dc)(2) (VAK = 7Vdc, RL = 100Ω, TC = 25°C) IGT - 1.0 mA Gate trigger voltage (continuous dc) (VAK = 7Vdc, RL = 100Ω, TC = 25°C) (VAK = Rated VDRM, RL = 100Ω, TJ = 100°C) VGT VGD 0.1 1.0 - Volts - 5.0 Peak forward blocking voltage(1) MCR1906-1 MCR1906-2 MCR1906-3 MCR1906-4 MCR1906-5 MCR1906-6 MCR1906-7 MCR1906-8 vDRM Peak forward blocking current (Rated VDRM @ TJ = 100°C) Holding current (VAK = 7Vdc) IH phone +1.908.245-7200 fax +1.908.245-0555 Volts µA mA Note 1: VDRM and VRRM for all types can be applied on a continuous dc basis without incurring damage. Note 2: RGK current is not included in measurement. 144 Market Street Kenilworth NJ 07033 USA Unit [email protected] www.digitroncorp.com Rev. 20130128 DIGITRON SEMICONDUCTORS MCR1906 SERIES SILICON CONTROLLED RECTIFIERS MECHANICAL CHARACTERISTICS Case TO-39 Marking Alpha-numeric Pin out See below TO-39 144 Market Street Kenilworth NJ 07033 USA A B C D E F G H J Inches Min Max 0.335 0.370 0.305 0.335 0.240 0.260 0.016 0.021 0.009 0.041 0.016 0.019 0.200 BSC 0.028 0.034 0.029 0.045 K 0.500 L M P R 0.250 45°C BSC 0.050 0.100 - phone +1.908.245-7200 fax +1.908.245-0555 0.750 Millimeters Min Max 8.510 9.390 7.750 8.500 6.100 6.600 0.410 0.530 0.230 1.040 0.410 0.480 5.080 BSC 0.720 0.860 0.740 1.140 12.70 19.05 0 0 6.350 45°C BSC 1.270 2.540 - [email protected] www.digitroncorp.com Rev. 20130128