Technical Datasheet DS05 SuperFlux LEDs Introduction This revolutionary package design allows the lighting designer to reduce the number of LEDs required and provide a more uniform and unique illuminated appearance than with other LED solutions. This is possible through the efficient optical package design and highcurrent capabilities. The low profile package can be easily coupled with reflectors or lenses to efficiently distribute light and provide the desired lit appearance. This product family employs the world's brightest red, redorange, amber, blue, cyan, and green LED materials, which Key Benefits Rugged Lighting Products Electricity Savings Maintenance Savings allow designers to match the color of many lighting applications like vehicle signal lamps, specialty lighting, and electronic signs. HPWAMH00XXXX HPWTMH00XXXX HPWADH00XXXX HPWTDH00XXXX HPWTRD00XXXX HPWTBH00XXXX HPWTMD00XXXX HPWTRL00XXXX HPWTDD00XXXX HPWTML00XXXX HPWTBD00XXXX HPWTDL00XXXX HPWTRH00XXXX HPWTBL00XXXX HPWNMB00XXXX HPWNMC00XXXX HPWNMG00XXXX Features High Luminance Uniform Color Low Power Consumption Low Thermal Resistance Low Profile Meets SAE/ECE/JIS Automotive Color Requirements Packaged in tubes for use with automatic insertion equipment Typical Applications Automotive Exterior Lighting Electronic Signs and Signals Specialty Lighting Selection Guide Table 1. Total Flux ΦV (LM) @ 70 mA[1](HPWA, HPWT) 50 mA (HPWN) Typ. Total Included Angle θ0.90 V (Degrees) [2] Typ. View Angle θ1/2 2θ (Degrees) Typ. 95 60 90 55 44 X 88 100 60 50 25x68 70 50 30 44 X 88 100 60 50 25x68 70 50 30 44 X 88 100 60 50 25x68 70 50 30 Device Type LED Color HPWAMH00 HPWADH00 AS AlInGaP RedOrange 2.0 HPWTRD00 HPWTMD00 HPWTDD00 HPWTBD00 TS AlInGaP Red 3.8 HPWTRH00 HPWTMH00 HPWTDH00 HPWTBH00 TS AlInGaP RedOrange 5.0 HPWTRL00 HPWTML00 HPWTDL00 HPWTBL00 TS AlInGaP Amber 2.5 HPWNMB00 InGaN Blue 2.0 110 90 HPWNMC00 InGaN Cyan 5.0 110 90 HPWNMG00 InGaN Green 4.5 110 90 Notes: 1.Φv is the total luminous flux output as measured with an integrating sphere after the device has stabilized. (RθJA = 200°C/W, TA = 25ºC) 2.θ0.90 V is the included angle at which 90% of the total luminous flux is captured. SuperFlux LEDs Technical Datasheet DS05 (11/07) 2 Outline Drawings Notes: 1.Dimensions are in millimeters (inches). 2.Dimensions without tolerances are nominal. SuperFlux LEDs Technical Datasheet DS05 (11/07) 3 Absolute Maximum Ratings at TA = 25ºC Table 2. Parameter DC Forward Current HPWA [1] HPWT HPWN Units 70 70 50 mA Power Dissipation 187 221 233 mW Reverse Voltage (IR = 100 μA) 10 10 0.55 Operating Temperature Range V 40 to +100 ºC Storage Temperature Range 55 to +100 ºC High Temperature Chamber 125ºC, 2 Hours LED Junction Temperature 125ºC Solder Conditions [2] Preheat Temperature Solder Temperature 85 +/ 15°C, 20 sec (Max 30 sec) 235 +/ 5°C, 2.5 +/ 0.5 sec [1.5mm (0.06 in) below seating plane Notes: 1.Derate as shown in Figures 4a, 4b and 4c. 2.Detail wave soldering instructions found in Application Brief AB13. Optical Characteristics at TA = 25°C, IF = 70 mA (HPWA, HPWT), IF = 50 mA (HPWN), RθJA = 200°C/W Table 3. Total Stabilized Flux Φv (lm) [1] Typ. Total Instantaneous Flux Φv (lm) [2] Typ. Luminous Intensity to Total Flux Iv(cd)/Φv(lm) Typ. Color, Dominant Wavelength λd (nm)[3] Typ. Total Included Angle θ0.90 V (Degrees)[4] Typ. 2.0 2.4 0.6 0.8 618 95 60 3.8 4.6 5.0 6.2 2.5 4.0 2.0 2.0 0.9 470 110 460 90 HPWNMC00 5 5.2 0.9 505 110 503 90 HPWNMG00 4.5 4.7 0.9 525 110 520 90 Device Type HPWAMH00 HPWADH00 HPWTRD00 HPWTMD00 HPWTDD00 HPWTBD00 HPWTRH00 HPWTMH00 HPWTDH00 HPWTBH00 HPWTRL00 HPWTML00 HPWTDL00 HPWTBL00 HPWNMB00 1.3 0.6 1.1 2.0 630 1.3 0.6 1.1 2.0 620 1.3 0.6 1.1 2.0 594 44x88 100 60 50 44x88 100 60 50 44x88 100 60 50 Peak Wavelength λpeak (nm) [3] Typ. 624 640 626 596 Viewing Angle 2θ1/2 v (Degrees) Typ. 90 55 25x68 70 50 30 25x68 70 50 30 25x68 70 50 30 Notes: 1.Total Stabilized Flux Φv is the total luminous flux output as measured with an integrating sphere after the device has stabilized to Tj ~ 60°C. 2.Total Instantaneous Flux Φv is the total luminous flux output as measured with an integrating sphere at 20ms duration. 3.The dominant wavelength is derived from the CIE Chromaticity Diagram and represents the perceived color of the device at Tj ~ 60 °C. 4.θ0.90 V is the included angle at which 90% of the total luminous flux is captured. SuperFlux LEDs Technical Datasheet DS05 (11/07) 4 Electrical Characteristics at TA=25°C Table 4. Forward Voltage VF (Volts) @ IF = 70mA (HPWA, HPWT) IF = 50 mA (HPWN) Reverse Breakdown VR (Volts)[1] @ IR = 100 μA Capacitance C (pF) VF = 0, F = 1MHz. Thermal Resistance RθJPIN (°C/W) Speed of Response τs (ns) [2] Device Type Min Typ Max Min Typ. Typ. Typ. Typ. HPWAxH00 1.83 2.2 2.67 10 20 40 155 20 HPWTxD00 2.19 2.6 3.03 10 20 40 125 20 HPWTxH00 2.19 2.6 3.03 10 20 40 125 20 HPWTxL00 2.19 2.6 3.15 10 20 40 125 20 HPWNxB00 3.00 3.8 4.60 0.55 0.65 1900 130 20 HPWNxC00 3.00 3.8 4.60 0.55 0.65 1900 130 20 HPWNxG00 3.00 3.9 4.60 0.55 0.65 1900 130 20 Notes: 1.Operation in reverse bias is not recommended. 2.τs is the time constant, et/τs. SuperFlux LEDs Technical Datasheet DS05 (11/07) 5 Figures1 Figure 3. HPWA/HPWTxx00 Relative Luminous Flux Figure 1a. Relative Intensity vs. Wavelength vs. Forward Current. 70 MAXIMUM DC CURRENT (mA) 1.0 HPWN-MC00 RELATIVE INTESITY HPWN-MG00 HPWN-MB00 0.5 60 50 Rth(j-a) = 300 C/W Rth(j-a) = 400 C/W 40 Rth(j-a) = 500 C/W Rth(j-a) = 600 C/W 30 20 10 0 0 20 40 60 80 100 AMBIENT TEMPERATURE (C) 0.0 350 400 450 500 550 600 650 Figure 4a. HPWAxx00 Maximum DC Forward Current WAVELENGTH (nm) vs. Ambient Temperature. Figure 1b. Relative Intensity vs. Wavelength (HPWN) 70 60 MAXIMUM DC CURRENT (mA) FORWARD CURRENT (mA) 70 HPWA 50 HPWT 40 30 20 60 50 40 Rth(j-a) = 300 C/W Rth(j-a) = 400 C/W 30 Rth(j-a) = 500 C/W 20 Rth(j-a) = 600 C/W 10 10 0 0 20 0 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 40 60 80 100 AMBIENT TEMPERATURE (C) 3.2 FORWARD VOLTAGE (V) Figure 4b. HPWTxx00 Maximum DC Forward Current Figure 2a. Forward Current vs. Forward Voltage vs. Ambient Temperature. MAXIMUM DC CURRENT (mA) 50 40 Rth(j-a) = 300 30 Rth(j-a) = 400 Rth(j-a) = 500 20 Rth(j-a) = 600 10 0 0 20 40 60 80 100 120 140 AMBIENT TEMPERATURE - (C) Figure 4c. HPWNxx00 Maximum DC Forward Current vs. Ambient Temperature. Figure 2b. Forward Current vs. Forward Voltage 1. All Figures Typical unless indicated as Maximum. Note: 1.24mm2 of Cu pad per emitter at cathode lead is recommended for lowest thermal resistance. SuperFlux LEDs Technical Datasheet DS05 (11/07) 6 RELATIVE LUMINOUS INTENSITY 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 OFF AXIS ANGLE (DEGREES) Figure 5e. HPWA(T)Dx00 Relative Luminous Intensity Figure 5a. HPWTRx00 Relative Luminous Intensity vs. vs. Off Axis Angle. Off Axis Angle. Figure 5b. HPWAMx00 Relative Luminous Intensity Figure 5f. HPWTBx00 Relative Luminous Intensity vs. Off Axis Angle. vs. Off Axis Angle. 1.4 1.3 RELATIVE LUMINOUS INT 1.2 1.1 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 Typical Upper Bound Typical Lower Bound 0.1 0 -100 -80 -60 -40 -20 0 20 40 60 80 OFF AXIS ANGLE (DEGREES) Figure 5c. HPWTMx00 Relative Luminous Intensity Figure 5g. HPWNMx00 Relative Luminous Intensity vs. Off Axis Angle. vs. Off Axis Angle 1.0 RELATIVE LUMINOUS INTENSITY 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 OFF AXIS ANGLE (DEGREES) Figure 5d. HPWTDx00 Relative Luminous Intensity vs. Off Axis Angle. 1. All Figures Typical unless indicated as Maximum. SuperFlux LEDs Technical Datasheet DS05 (11/07) 7 100 90 SuperFlux Product Binning This section provides bin selection assistance for SuperFlux LEDs. Additional category and label details for SuperFlux product can be found in AB207. Product availability varies by color and other factors, and not all binselection combinations are avail able. Contact your Philips Lumileds representative for further assistance. Luminous Flux Bins Part Number Bin Code Minimum Luminous Flux @ 70 mA (HPWA, HPWT) @ 50 mA (HPWN) [1] Maximum Luminous Flux @ 70 mA (HPWA, HPWT) @ 50 mA (HPWN) [1] HPWAMH00 HPWADH00 B C 1 1.5 1.8 2.4 HPWTRD00 HPWTMD00 HPWTDD00 HPWTBD00 D E F G 2 2.5 3 3.5 3 3.6 4.2 4.8 HPWTRH00 HPWTMH00 HPWTDH00 HPWTBH00 E F G H J 2.5 3 3.5 4 5 3.6 4.2 4.8 6.1 7.3 HPWTRL00 HPWTML00 HPWTDL00 HPWTBL00 C D E E 1.5 2 2.5 2.5 2.4 3 3.6 3.6 HPWNMB00 1 HPWNMC00 3 HPWNMG00 3 Note: 1.Total Luminous Flux as measured with an integrating sphere after the device has stabilized. Tj ~ 60°C Dominant Wavelength Bins, RedOrange Bin Code Minimum Dominant Wavelength (nm) Maximum Dominant Wavelength (nm) 1 611 617 2 615 621 3 619 629 Bin Code Minimum Dominant Wavelength (nm) Maximum Dominant Wavelength (nm) 0 622 645 Bin Code Minimum Dominant Wavelength (nm) Maximum Dominant Wavelength (nm) 1 587 591 2 589 594 9 592 595 3 592 597 Dominant Wavelength Bins, Red Dominant Wavelength Bins, Amber SuperFlux LEDs Technical Datasheet DS05 (11/07) 8 Forward Voltage Bins, Red, RedOrange, and Amber @ 70 mA Bin Code Minimum Voltage Maximum Voltage 1 2.19 2.43 2 2.31 2.55 3 2.43 2.67 4 2.55 2.79 5 2.67 2.91 6 2.79 3.03 7 2.91 3.15 SuperFlux LEDs Technical Datasheet DS05 (11/07) 9 Company Information LUXEON® is developed, manufactured and marketed by Philips Lumileds Lighting Company. Philips Lumileds is a worldclass supplier of Light Emitting Diodes (LEDs) producing billions of LEDs annually. Philips Lumileds is a fully integrated supplier, producing core LED material in all three base colors (Red, Green, Blue) and White. Philips Lumileds may make process or materials changes affecting the perform ance or other characteristics of our products. These products supplied after such changes will continue to meet published specifications, but may not be identical to products supplied as samples or under prior orders. Philips Lumileds has R&D centers in San Jose, California and in The Netherlands and production capabilities in San Jose and Penang, Malaysia. Founded in 1999, Philips Lumileds is the highflux LED technology leader and is dedicated to bridging the gap between solidstate LED technology and the lighting world. Philips Lumileds technology, LEDs and systems are enabling new applications and markets in the lighting world. www.luxeon.com www.lumiledsfuture.com For technical assistance or the location of your nearest sales office contact any of the following: North America: 1 888 589 3662 [email protected] Europe: 00 800 443 88 873 [email protected] Asia Pacific: 800 5864 5337 [email protected] ©2007 Philips Lumileds Lighting Company. All rights reserved. Product specifications are subject to change without notice. Luxeon is a registered trademark of the Philips Lumileds Lighting Company in the United States and other countries. Japan: 800 5864 5337 [email protected]