K1149 Series 5V Crystal Clock Oscillators ! 4-pin Package, Compatible with 14-pin DIL ax. mM m 2 13, ax. mM m 8 20, ! 40 to 160MHz Frequency Range (Discrete Higher Frequencies Available 9 HZ E K11040.000 MTE COD 1 TI DA C ! Designed to Drive Standard ECL 10K and 10KH Families ! ECL and PECL Options Available ! Dual Complementary Output Available ! 50Ω Drive Capability ! Internal 470W Output Pull-Down Resistor Available PIN 1 mm 2* 6,2 x. Ma *> 140MHz (Height) = 8,51mm Max E L E C T R I C A L S P E C I F I C AT I O N S MODEL See Part Numbering Guide Below Frequency Range (MHz) 40 to 160 Higher Frequency Available (MHz) 180, 200, 220 Frequency Stability (ppm) Overall Inclusive of calibration, temperature, voltage, load, shock,vibration, aging 0°C to 70°C ±100 Temperature Range (°C) Operating 0°C to +70°C Storage -55°C to +125°C Supply Voltage (V) ECL (VEE) -5.2 ± 5% PECL (VCC) +5.0 ± 5% Supply Current (mA) Typical 28; 55 on R-Suffix (Option 3) Maximum 60; 90 on R-Suffix (Option 3) Jitter (Typical) 5ps RMS @ 40MHz Start up Time (ms) <10 PA R T N U M B E R I N G G U I D E ( U s e t h i s c h a r t f o r o r d e r i n g ) PIN 1 K1149AA K1149AB Case GND Case GND K1149AC N/C 7 VEE VSS VEE 8 ECL Out ECL Out ECL Out 14 VSS VEE K1149AM N/C VSS & K1149BA K1149BC Comp. Out Comp Out Comp Out VSS & VEE Case GND Case GND ECL Out VSS & VEE Case GND K1149BM PECL Out VCC ECL Out VSS & ECL Out PECL Out VEE VCC Case GND 40 to 125 40 to 160 Option 1, 2, 3 2, 3 N/C VEE & Case GND Case GND VSS & Frequency (MHz) K1149CA Options Available 1. Optional +5.0 ± 10% Operation at VSS 2. 50ppm (K1149XX5 available only in frequency range of 40MHz to 160MHz 3. Optional internal pull down resistor available only in the range of 40MHz to 160MHz - K1149XX-R 2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585 800-888-1499 or www.champtech.com 1 K1149 Series 5V Crystal Clock Oscillators TEST CIRCUIT DIAGRAM OUTPUT WAVEFORM ECL PECL Specifications Parameter Symbol Units Test Condition Min. Specifications Typ. Max Test Condition Min. Typ. Max. Ground Reference VSS Volts Reference 0 Power Supply (ECL) VEE Volts Reference -5.2 Power Supply (PECL) VCC Volts N/A “0” Level VOL Volts 50Ω into VSS-2 VSS-1.95 “1” Level VOH Volts 50Ω into VSS-2 VSS-1.02 Rise Time TR ps 50Ω into, 20% to 80% 1.0 2.0 50Ω into, 20% to 80% 1.0 2.0 Fall Time TF ps 50Ω into, 20% to 80% 1.0 2.0 50Ω into, 80% to 20% 1.0 2.0 TOL ps 50% 1.0 50% % VSS -1.3 60 VCC -1.3 Overlap Symmetry S Reference 0 N/A - Reference VSS-1.6 4.75 50Ω into VCC-2 VCC-1.95 VSS-0.74 50Ω into VCC-2 VCC-1.02 40 5.0 5.25 VCC-1.6 VCC-1.74 1.0 40 60 MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS TEST METHODS REFERENCE PROCEDURES DESCRIPTION Temperature Cycle MIL-STD-833, Mtd 1010, Cond. B -55°C to +125°C; Air-to-Air; 100 cycles; 10 min. dwell Mechanical Shock MIL-STD-883, Mtd 2002, Cond. B 1500 g’s Vibration MIL-STD 883, Mtd 2007, Cond. B 20-2000 Hz; 0.06 inch; 15g’s; 3 planes Humidity Steady State MIL-STD-202, Mtd 103 40°C; 90%-95% R.H.; 56 days Thermal Shock MIL-STD-883, Mtd 1011.7 Cond. B 100°C to 0°C; Water-to-Water; 15 cycles Electrostatic Discharge MIL-STD-883, Mtd 3015 Class II 2 KV to 4 KV Threshold Solderability Hermeticity MIL-STD-883, Mtd 2022.2 MIL-STD-883, Mtd 1014.8, Cond. A1 Solder dip; Meniscograph Criteria Mass spectro. 2 x 10-8 atmos. CC/sec He Resistance to Soldering Lead Integrity MIL-STD-202, Mtd 210D, Cond. J 235°C; 30 seconds MIL-STD-883, Mtd 2004.5, Cond. A, B1 Lead tension & bend stress Marking Permanence Life Test MIL-STD-883, Mtd 2015.8 MIL-STD-883, Mtd 1005.6 Resistance to solvents 125°C, powered, 1000 hours minimum 2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585 800-888-1499 or www.champtech.com 2