ACT ACTF377 Low-loss, compact, and economical surface-acoustic-wave (saw) filter Datasheet

Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
The ACTF377/280.0/QCC8C is a low-loss, compact, and economical surface-acoustic-wave (SAW)
filter in a surface-mount ceramic QCC8C case for wireless LAN applications.
1.Package Dimension (QCC8C)
2.
Pins
Configuration
6
Input
2
Output
1,3,5,7
To be Grounded
4,8
Case Ground
Sign
Data (unit: mm)
Sign
Data (unit: mm)
A
2.08
E
1.20
B
0.60
F
1.35
C
1.27
G
5.00
D
2.54
H
5.00
3. Matching Network (50 Ωunbalanced)
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
1 OF 3
Issue : 1 C1
Date : SEPT 04
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
4.Typical Frequency Response
5.Performance
5-1. Maximum Ratings
Rating
Value
Units
Source Power
PS
10
dBm
DC Voltage
VDC
0
V
-40 to +85
°C
+235
°C
Storage Temperature
Soldering Temperature
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
2 OF 3
Issue : 1 C1
Date : SEPT 04
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
5-2. Electronic Characteristics
Operating temperature:
Terminating source impedance:
Terminating load impedance:
TA = -10 … +60 °C
ZS = 50 Ω unbalanced and matching network
ZL = 50 Ω unbalanced and matching network
Characteristics
Centre frequency
fC
Minimum insertion attenuation
(including matching network)
αmin
3dB Bandwidth
BW3dB
Amplitude ripple (p-p)
fC±7MHz
Δ α
Group delay ripple (p-p)
fC±7MHz
Δτ
Relative attenuation (relative to αmin)
230 MHz ~ 260 MHz
300 MHz ~ 330 MHz
αrel
Temperature coefficient of frequency
TCf
Minimum
Typical
Maximum
Units
--
280.000
--
MHz
--
11.0
13.5
dB
16
20
--
MHz
--
±0.5
--
dB
--
40
100
ns
35
28
46
37
---
dB
dB
--
-87
--
ppm/K
iCAUTION: Electrostatic Sensitive Device. Observe precautions for handling!
1.
2.
3.
4.
5.
6.
The frequency f C is defined as the midpoint between the 3dB frequencies.
Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture that is
connected to a 50 Ω test system with VSWR ≤1.2:1. The test fixture L and C are adjusted for minimum insertion
loss at the filter centre frequency, f C. Note that insertion loss, bandwidth, and passband shape are dependent on
the impedance matching component values and quality.
Unless noted otherwise, specifications apply over the entire specified operating temperature range.
The specifications of this device are based on the test circuit shown above and subject to change or
obsolescence without notice.
All equipment designs utilizing this product must be approved by the appropriate government agency prior to
manufacture or sale.
Our liability is only assumed for the Surface Acoustic Wave (SAW) component(s) per se, not for applications,
processes and circuits implemented within components or assemblies.
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
3 OF 3
Issue : 1 C1
Date : SEPT 04
Similar pages