AD AD712JR-REEL Dual precision, low cost, high speed, bifet op amp Datasheet

a
FEATURES
Enhanced Replacements for LF412 and TL082
AC PERFORMANCE
Settles to 60.01% in 1.0 ms
16 V/ms min Slew Rate (AD712J)
3 MHz min Unity Gain Bandwidth (AD712J)
DC PERFORMANCE
0.30 mV max Offset Voltage: (AD712C)
5 mV/8C max Drift: (AD712C)
200 V/mV min Open-Loop Gain (AD712K)
4 mV p-p max Noise, 0.1 Hz to 10 Hz (AD712C)
Surface Mount Available in Tape and Reel in Accordance with EIA-481A Standard
MIL-STD-883B Parts Available
Single Version Available: AD711
Quad Version: AD713
Available in Plastic Mini-DIP, Plastic SOIC, Hermetic
Cerdip, Hermetic Metal Can Packages and Chip Form
Dual Precision, Low Cost,
High Speed, BiFET Op Amp
AD712
CONNECTION DIAGRAMS
TO-99
(H) Package
AMPLIFIER NO. 1
+VS
AMPLIFIER NO. 2
OUTPUT
OUTPUT
INVERTING
OUTPUT
NONINVERTING
OUTPUT
INVERTING
INPUT
AD712
NONINVERTING
INPUT
–VS
Plastic Mini-DIP (N) Package
SOIC (R) Package and Cerdip (Q) Package
AMPLIFIER NO. 1
AMPLIFIER NO. 2
OUTPUT 1
8
V+
INVERTING 2
OUTPUT
7
OUTPUT
NONINVERTING 3
OUTPUT
6
V– 4
AD712
INVERTING
INPUT
NONINVERTING
5
INPUT
PRODUCT DESCRIPTION
The AD712 is a high speed, precision monolithic operational
amplifier offering high performance at very modest prices. Its
very low offset voltage and offset voltage drift are the results of
advanced laser wafer trimming technology. These performance
benefits allow the user to easily upgrade existing designs that use
older precision BiFETs and, in many cases, bipolar op amps.
The superior ac and dc performance of this op amp makes it
suitable for active filter applications. With a slew rate of 16 V/µs
and a settling time of 1 µs to ± 0.01%, the AD712 is ideal as a
buffer for 12-bit D/A and A/D Converters and as a high-speed
integrator. The settling time is unmatched by any similar IC
amplifier.
The combination of excellent noise performance and low input
current also make the AD712 useful for photo diode preamps.
Common-mode rejection of 88 dB and open loop gain of
400 V/mV ensure 12-bit performance even in high-speed unity
gain buffer circuits.
The AD712 is pinned out in a standard op amp configuration
and is available in seven performance grades. The AD712J and
AD712K are rated over the commercial temperature range of
0°C to +70°C. The AD712A, AD712B and AD712C are rated
over the industrial temperature range of –40°C to +85°C. The
AD712S and AD712T are rated over the military temperature
range of –55°C to +125°C and are available processed to MILSTD-883-B, Rev. C.
Extended reliability PLUS screening is available, specified over
the commercial and industrial temperature ranges. PLUS
screening includes 168-hour burn-in, as well as other environmental and physical tests.
The AD712 is available in an 8-lead plastic mini-DIP, SOIC,
cerdip, TO-99 metal can, or in chip form.
PRODUCT HIGHLIGHTS
1. The AD712 offers excellent overall performance at very
competitive prices.
2. Analog Devices’ advanced processing technology and with
100% testing guarantees a low input offset voltage (0.3 mV
max, C grade, 3 mV max, J grade). Input offset voltage is
specified in the warmed-up condition. Analog Devices’ laser
wafer drift trimming process reduces input offset voltage
drifts to 5 µV/°C max on the AD712C.
3. Along with precision dc performance, the AD712 offers
excellent dynamic response. It settles to ± 0.01% in 1 µs and
has a minimum slew rate of 16 V/µs. Thus this device is ideal
for applications such as DAC and ADC buffers which require a combination of superior ac and dc performance.
4. The AD712 has a guaranteed and tested maximum voltage
noise of 4 µV p-p, 0.1 Hz to 10 Hz (AD712C).
5. Analog Devices’ well-matched, ion-implanted JFETs ensure
a guaranteed input bias current (at either input) of 50 pA
max (AD712C) and an input offset current of 10 pA max
(AD712C). Both input bias current and input offset current
are guaranteed in the warmed-up condition.
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 1998
AD712–SPECIFICATIONS (V = 615 V @ T = +258C unless otherwise noted)
S
Parameter
Min
INPUT OFFSET VOLTAGE1
Initial Offset
TMIN to TMAX
vs. Temp
vs. Supply
76
TMIN to TMAX
76/76/76
Long-Term Offset Stability
INPUT BIAS CURRENT2
VCM = 0 V
VCM = 0 V @ TMAX
VCM = ± 10 V
INPUT OFFSET CURRENT
VCM = 0 V
VCM = 0 V @ TMAX
AD712J/A/S
Typ
0.3
7
95
1.0/0.7/0.7
2.0/1.5/1.5
10
AD712C
Typ
0.1
86
86
15
3
110
Max
Units
0.3
0.6
5
mV
mV
µV/°C
dB
dB
µV/Month
15
75
1.7/4.8/77
100
20
1.3
50
3.2
75
pA
nA
pA
10
0.3/0.7/11
25
0.6/1.6/26
5
0.1/0.3/5
25
0.6/1.6/26
5
0.3
10
0.7
pA
nA
0.3
0.6
5
10
120
90
mV
mV
µV/°C
pA
dB
dB
4.0
200
20
1.0
0.0003
MHz
kHz
V/µs
µs
%
3/1/1
4/2/2
20/20/20
25
1.0/0.7/0.7
2.0/1.5/1.5
10
25
120
90
3.4
4.0
200
20
1.0
0.0003
18
1.2
3.4
18
1.2
1.2
3 × 1012i5.5
3 × 1012i5.5
3 × 1012i5.5
3 × 1012i5.5
3 × 1012i5.5
3 × 1012i5.5
ΩipF
ΩipF
± 20
+14.5, –11.5
± 20
+14.5, –11.5
± 20
+14.5, –11.5
V
–VS + 4
76
76/76/76
70
70/70/70
7
100
80
80
Min
20
0.5/1.3/20
4.0
200
20
1.0
0.0003
INPUT VOLTAGE RANGE
Differential3
Common-Mode Voltage4
TMIN to TMAX
Common-Mode
Rejection Ratio
VCM = ± 10 V
TMIN to TMAX
VCM = ± 11 V
TMIN to TMAX
0.2
Max
75
1.7/4.8/77
100
FREQUENCY RESPONSE
Small Signal Bandwidth
Full Power Response
Slew Rate
Settling Time to 0.01%
Total Harmonic Distortion
INPUT IMPEDANCE
Differential
Common Mode
3/1/1
4/2/2
20/20/20
AD712K/B/T
Typ
25
0.6/1.6/26
120
90
16
Min
15
MATCHING CHARACTERISTICS
Input Offset Voltage
TMIN to TMAX
Input Offset Voltage Drift
Input Bias Current
Crosstalk @ f = 1 kHz
@ f = 100 kHz
3.0
Max
A
+VS – 2
88
84
84
80
–VS + 4
80
80
76
74
+VS – 2
88
84
84
80
–VS + 4
86
86
76
74
+VS – 2 V
94
90
90
84
dB
dB
dB
dB
INPUT VOLTAGE NOISE
2
45
22
18
16
2
45
22
18
16
2
45
22
18
16
µV p-p
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
INPUT CURRENT NOISE
0.01
0.01
0.01
pA/√Hz
400
V/mV
V/mV
OPEN-LOOP GAIN
150
400
100/100/100
200
100
OUTPUT CHARACTERISTICS
Voltage
+13, –12.5
+13.9, –13.3
± 12/± 12/612 +13.8, –13.1
Current
25
POWER SUPPLY
Rated Performance
Operating Range
Quiescent Current
64.5
± 15
5.0
400
200
100
+13, –12.5 +13.9, –13.3
612
+13.8, –13.1
25
618
6.8
64.5
± 15
5.0
+13, –12.5 +13.9, –13.3
612
+13.8, –13.1
25
618
6.0
64.5
± 15
5.0
V
V
mA
618
5.6
V
V
mA
NOTES
1
Input Offset Voltage specifications are guaranteed after 5 minutes of operation at T A = +25°C.
2
Bias Current specifications are guaranteed maximum at either input after 5 minutes of operation at T A = +25°C. For higher temperatures, the current doubles every 10°C.
3
Defined as voltage between inputs, such that neither exceeds ± 10 V from ground.
4
Typically exceeding –14.1 V negative common-mode voltage on either input results in an output phase reversal.
Specifications in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min and max
specifications are guaranteed, although only those shown in boldface are tested on all production units.
Specifications subject to change without notice.
–2–
REV. B
AD712
ABSOLUTE MAXIMUM RATINGS 1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 18 V
Internal Power Dissipation2
Input Voltage3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 18 V
Output Short Circuit Duration . . . . . . . . . . . . . . . . . Indefinite
Differential Input Voltage . . . . . . . . . . . . . . . . . . +VS and –VS
Storage Temperature Range (Q, H) . . . . . . . –65°C to +150°C
Storage Temperature Range (N, R) . . . . . . . . –65°C to +125°C
Operating Temperature Range
AD712J/K . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
AD712A/B/C . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
AD712S/T . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to +125°C
Lead Temperature Range (Soldering 60 sec) . . . . . . . . +300°C
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
Thermal Characteristics:
8-Lead Plastic Package:
θJA = 165°C/Watt
8-Lead Cerdip Package:
θJC = 22°C/Watt; θJA = 110°C/Watt
8-Lead Metal Can Package: θJC = 65°C/Watt; θJA = 150°C/Watt
8-Lead SOIC Package:
θJA = 100°C
3
For supply voltages less than ± 18 V, the absolute maximum input voltage is equal
to the supply voltage.
ORDERING GUIDE
Model
Temperature
Range
Package
Description
AD712ACHIPS
AD712AH
AD712AQ
AD712BH
AD712BQ
AD712CH
AD712CN
AD712JN
AD712JR
AD712JR-REEL
AD712JR-REEL7
AD712KN
AD712KR
AD712KR-REEL
AD712KR-REEL7
AD712SCHIPS
AD712SQ
AD712SQ/883B
AD712TQ
AD712TQ/883B
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
–55°C to +125°C
–55°C to +125°C
–55°C to +125°C
–55°C to +125°C
–55°C to +125°C
Bare Die
8-Lead Metal Can
8-Lead Ceramic DIP
8-Lead Metal Can
8-Lead Ceramic DIP
8-Lead Metal Can
8-Lead Plastic DIP
8-Lead Plastic DIP
8-Lead Plastic SOIC
8-Lead Plastic SOIC
8-Lead Plastic SOIC
8-Lead Plastic DIP
8-Lead Plastic SOIC
8-Lead Plastic SOIC
8-Lead Plastic SOIC
Bare Die
8-Lead Ceramic DIP
8-Lead Ceramic DIP
8-Lead Ceramic DIP
8-Lead Ceramic DIP
METALIZATION PHOTOGRAPH
Dimensions shown in inches and (mm).
Contact factory for latest dimensions.
REV. B
–3–
Package
Option
H-08A
Q-8
H-08A
Q-8
H-08A
N-8
N-8
R-8
R-8
R-8
N-8
R-8
R-8
R-8
Q-8
Q-8
Q-8
Q-8
AD712–Typical Performance Characteristics
20
RL = 2kV
258C
5
0
0
10
15
5
SUPPLY VOLTAGE 6 Volts
INPUT BIAS CURRENT (VCM = 0) – Amps
QUIESCENT CURRENT – mA
4
3
2
0
10
15
5
SUPPLY VOLTAGE 6 Volts
Figure 4. Quiescent Current vs.
Supply Voltage
SHORT CIRCUIT CURRENT LIMIT – mA
INPUT BIAS CURRENT – pA
100
75
VS = +15V
258C
50
25
0
–10
0
5
–5
COMMON MODE VOLTAGE – Volts
10
Figure 7. Input Bias Current vs.
Common Mode Voltage
RL = 2kV
258C
5
0
10
15
5
SUPPLY VOLTAGE 6 Volts
25
20
615V SUPPLIES
15
10
5
0
10
20
100
1k
LOAD RESISTANCE – V
10k
Figure 3. Output Voltage Swing
vs. Load Resistance
106
100
107
108
109
1010
10
1.0
0.1
1011
1012
–60 –40 –40
20
MAX J GRADE LIMIT
–VOUT
Figure 2. Output Voltage Swing vs.
Supply Voltage
6
5
10
0
20
Figure 1. Input Voltage Swing vs.
Supply Voltage
+VOUT
OUTPUT IMPEDANCE – V
10
15
0.01
1k
0 20 40 60 80 100 120 140
TEMPERATURE – 8C
10k
100k
1M
FREQUENCY – Hz
10M
Figure 5. Input Bias Current vs.
Temperature
Figure 6. Output Impedance vs.
Frequency
26
5.0
24
+ OUTPUT CURRENT
22
20
18
– OUTPUT CURRENT
16
14
12
10
–60 –40 –20 0 20 40 60 80 100 120 140
AMBIENT TEMPERATURE – 8C
Figure 8. Short Circuit Current
Limit vs. Temperature
–4–
UNITY GAIN BANDWIDTH – MHz
15
30
OUTPUT VOLTAGE SWING – Volts p–p
OUTPUT VOLTAGE SWING – Volts
INPUT VOLTAGE SWING – Volts
20
4.5
4.0
3.5
3.0
–60 –40 –20
0 20 40 60 80 100 120 140
TEMPERATURE – 8C
Figure 9. Unity Gain Bandwidth vs.
Temperature
REV. B
AD712
60
60
40
40
GAIN
PHASE
2kV
100pF
LOAD
20
20
120
–20
10
100
1k
10k
100k
FREQUENCY – Hz
1M
105
0
5
10
15
SUPPLY VOLTAGE 6 Volts
Figure 11. Open-Loop Gain vs.
Supply Voltage
100
30
40
20
100
1k
10k
100k
FREQUENCY – Hz
Figure 13. Common Mode Rejection vs. Frequency
3V RMS
RL = 2kV
CL = 100pF
–100
–110
–120
–130
100
100k
Figure 16. Total Harmonic Distortion vs. Frequency
REV. B
20
RL = 2kV
258C
VS = 615V
15
10
5
1M
INPUT FREQUENCY – Hz
8
6
4
2
–2
ERROR 1% 0.1% 0.01%
–4
–6
–8
–10
0.5
10M
1% 0.1% 0.01%
0
0.6
0.7
0.8
0.9
SETTLING TIME – ms
1.0
Figure 15. Output Swing and Error
vs. Settling Time
25
20
100
10
15
10
5
1
1k
10k
FREQUENCY – Hz
VS = 615V SUPPLIES
WITH 1V p-p SINE
WAVE 258C
Figure 12. Power Supply Rejection
vs. Frequency
1k
INPUT NOISE VOLTAGE – nV/ Hz
–90
25
Figure 14. Large Signal Frequency
Response
–70
–80
20
10
0
100k
1M
– SUPPLY
40
0
10
100
1k
10k
100k
1M
SUPPLY MODULATION FREQUENCY – Hz
SLEW RATE – V/ms
0
10
60
OUTPUT SWING FROM 0V TO 6VOLTS
VS = 615V
VCM = 1Vp-p
258C
60
+ SUPPLY
80
20
Figure 10. Open-Loop Gain and
Phase Margin vs. Frequency
OUTPUT VOLTAGE – Volts p–p
CMR – dB
RL = 2kV
258C
110
100
95
–20
10M
80
THD – dB
115
100
0
0
110
POWER SUPPLY REJECTION – dB
80
OPEN LOOP GAIN – dB
80
125
PHASE MARGIN – 8C
100
OPEN LOOP GAIN – dB
100
1
10
100
1k
FREQUENCY – Hz
10k
100k
Figure 17. Input Noise Voltage
Spectral Density
–5–
0
0
100 200 300 400 500 600 700 800 900
INPUT ERROR SIGNAL – mV
(AT SUMMING JUNCTION)
Figure 18. Slew Rate vs. Input
Error Signal
AD712
+VS
25
SLEW RATE – V/ms
0.1mF
1/2
AD712
INPUT
OUTPUT
100pF
2kV
0.1mF
20
–VS
Figure 20. T.H.D. Test Circuit
VOUT
15
–60
–40
–20
0
20
40
60
80
TEMPERATURE – 8C
100
120
20kV
+VS
140
2
Figure 19. Slew Rate vs. Temperature
20V p-p
6
8
1/2
AD712
3
VIN
CROSSTALK = 20 LOG
2.2kV
1
7
5kV
5kV
VOUT
1/2
AD712 5
4
–VS
10VIN
Figure 21. Crosstalk Test Circuit
+VS
100
100
90
90
0.1mF
VOUT
1/2
AD712
RL
2kV
VIN
CL
100pF
10
10
0%
0%
0.1mF
SQUARE
WAVE
INPUT
1ms
5V
50mV
100ns
–VS
Figure 22a. Unity Gain Follower
Figure 22b. Unity Gain Follower
Pulse Response (Large Signal)
5kV
100
100
90
90
+VS
Figure 22c. Unity Gain Follower
Pulse Response (Small Signal)
0.1mF
VIN
5kV
VOUT
1/2
AD712
SQUARE
WAVE
INPUT
10
10
RL
2kV
0.1mF
CL
100pF
0%
0%
1ms
5V
50mV
200ns
–VS
Figure 23a. Unity Gain Inverter
Figure 23b. Unity Gain Inverter Pulse
Response (Large Signal)
–6–
Figure 23c. Unity Gain Inverter
Pulse Response (Small Signal)
REV. B
AD712
In addition to a significant improvement in settling time, the
low offset voltage, low offset voltage drift, and high open-loop
gain of the AD711/AD712 family assures 12-bit accuracy over
the full operating temperature range.
OPTIMIZING SETTLING TIME
Most bipolar high-speed D/A converters have current outputs;
therefore, for most applications, an external op amp is required
for current-to-voltage conversion. The settling time of the converter/op amp combination depends on the settling time of the
DAC and output amplifier. A good approximation is:
The excellent high-speed performance of the AD712 is shown in
the oscilloscope photos of Figure 25. Measurements were taken
using a low input capacitance amplifier connected directly to the
summing junction of the AD712 – both photos show the worst
case situation: a full-scale input transition. The DAC’s 4 kΩ
[10 kΩ||8 kΩ = 4.4 kΩ] output impedance together with a
10 kΩ feedback resistor produce an op amp noise gain of 3.25.
The current output from the DAC produces a 10 V step at the
op amp output (0 to –10 V Figure 25a, –10 V to 0 V Figure
25b.)
t S Total = (t S DAC )2 + (t S AMP )2
The settling time of an op amp DAC buffer will vary with the
noise gain of the circuit, the DAC output capacitance, and with
the amount of external compensation capacitance across the
DAC output scaling resistor.
Settling time for a bipolar DAC is typically 100 ns to 500 ns.
Previously, conventional op amps have required much longer
settling times than have typical state-of-the-art DACs; therefore,
the amplifier settling time has been the major limitation to a
high-speed voltage-output D-to-A function. The introduction of
the AD711/AD712 family of op amps with their 1 µs (to ± 0.01%
of final value) settling time now permits the full high-speed
capabilities of most modern DACs to be realized.
Therefore, with an ideal op amp, settling to ± 1/2 LSB (± 0.01%)
requires that 375 µV or less appears at the summing junction.
This means that the error between the input and output (that
voltage which appears at the AD712 summing junction) must be
less than 375 µV. As shown in Figure 25, the total settling time
for the AD712/AD565 combination is 1.2 microseconds.
0.1mF
BIPOLAR
OFFSET ADJUST
R2
GAIN 100V
ADJUST
REF
OUT
R1
100V
VCC
BIPOLAR
OFF
20V
SPAN
+
10V
AD565A
–
REF
IN
19.95kV
5kV
9.95kV
10V
SPAN
0.5mA
5kV
IREF
DAC
REF
GND
IOUT = 4 3
IREF 3 CODE
20kV
IO
10pF
+15V
0.1mF
DAC
OUT
1/2
AD712
8kV
OUTPUT
–10V TO +10V
0.1mF
–VEE
0.1mF
POWER
GND
MSB
LSB
–15V
Figure 24. ± 10 V Voltage Output Bipolar DAC
1mV
5V
1mV
100
100
90
90
SUMMING
JUNCTION
SUMMING
JUNCTION
0V
0V
10
OUTPUT
10
0%
OUTPUT
0%
–10V
–10V
500ns
500ns
b. (Full-Scale Positive Transition)
a. (Full-Scale Negative Transition)
Figure 25. Settling Characteristics for AD712 with AD565A
REV. B
5V
–7–
AD712
OP AMP SETTLING TIME A MATHEMATICAL MODEL
The design of the AD712 gives careful attention to optimizing
individual circuit components; in addition, a careful trade-off
was made: the gain bandwidth product (4 MHz) and slew rate
(20 V/µs) were chosen to be high enough to provide very fast
settling time but not too high to cause a significant reduction in
phase margin (and therefore stability). Thus designed, the
AD712 settles to ± 0.01%, with a 10 V output step, in under
1 µs, while retaining the ability to drive a 250 pF load capacitance when operating as a unity gain follower.
When RO and IO are replaced with their Thevenin VIN and RIN
equivalents, the general purpose inverting amplifier of Figure
26b is created. Note that when using this general model, capacitance CX is EITHER the input capacitance of the op amp if a
simple inverting op amp is being simulated OR it is the combined capacitance of the DAC output and the op amp input if
the DAC buffer is being modeled.
1/2
AD712
If an op amp is modeled as an ideal integrator with a unity gain
crossover frequency of ωο/2π, Equation 1 will accurately describe the small signal behavior of the circuit of Figure 26a,
consisting of an op amp connected as an I-to-V converter at the
output of a bipolar or CMOS DAC. This equation would completely describe the output of the system if not for the op amp’s
finite slew rate and other nonlinear effects.
VOUT
RL
CL
CF
RIN
R
VIN
CX
Figure 26b. Simplified Model of the AD712
Used as an Inverter
Equation 1.
VO
–R
=
I IN
R(C f = CX ) 2  GN

s +
+ RC f  s + 1
ωο
 ωο

In either case, the capacitance CX causes the system to go from
a one-pole to a two-pole response; this additional pole increases
settling time by introducing peaking or ringing in the op amp
output. Since the value of CX can be estimated with reasonable
accuracy, Equation 2 can be used to choose a small capacitor,
CF, to cancel the input pole and optimize amplifier response.
Figure 27 is a graphical solution of Equation 2 for the AD712
with R = 4 kΩ.
ωο
where 2 =op amp’s unity gain frequency
π

R 
GN = “noise” gain of circuit 1 + R 
O
This equation may then be solved for Cf:
60
Equation 2.
Cf =
2 − GN 2 RC X ω ο + (1 − GN )
+
Rω ο
Rω ο
50
GN = 4.0
40
CX
In these equations, capacitor CX is the total capacitor appearing
the inverting terminal of the op amp. When modeling a DAC
buffer application, the Norton equivalent circuit of Figure 26a
can be used directly; capacitance CX is the total capacitance of
the output of the DAC plus the input capacitance of the op amp
(since the two are in parallel).
30
GN = 3.0
GN = 2.0
20
GN = 1.5
GN = 1.0
10
0
0
1/2
AD712
VOUT
RL
CL
10
20
30
CF
40
50
60
Figure 27. Value of Capacitor CF vs. Value of CX
CF
R
IO
RO
CX
Figure 26a. Simplified Model of the AD712 Used as a
Current-Out DAC Buffer
–8–
REV. B
AD712
The photos of Figures 28a and 28b show the dynamic response
of the AD712 in the settling test circuit of Figure 29.
5V
100
90
The input of the settling time fixture is driven by a flat-top pulse
generator. The error signal output from the false summing node
of A1 is clamped, amplified by A2 and then clamped again. The
error signal is thus clamped twice: once to prevent overloading
amplifier A2 and then a second time to avoid overloading the
oscilloscope preamp. The Tektronix oscilloscope preamp type
7A26 was carefully chosen because it does not overload with
these input levels. Amplifier A2 needs to be a very high speed
FET-input op amp; it provides a gain of 10, amplifying the error
signal output of A1.
10
GUARDING
0%
5mV
500ns
Figure 28a. Settling Characteristics 0 V to +10 V Step
Upper Trace: Output of AD712 Under Test (5 V/Div)
Lower Trace: Amplified Error Voltage (0.01%/Div)
5V
100
90
The low input bias current (15 pA) and low noise characteristics
of the AD712 BiFET op amp make it suitable for electrometer
applications such as photo diode preamplifiers and picoampere
current-to-voltage converters. The use of a guarding technique
such as that shown in Figure 30, in printed circuit board layout
and construction is critical to minimize leakage currents. The
guard ring is connected to a low impedance potential at the
same level as the inputs. High impedance signal lines should not
be extended for any unnecessary length on the printed circuit
board.
TO-99 (H) PACKAGE
PLASTIC MINI-DIP (N) PACKAGE
CERDIP (Q) PACKAGE
AND SOIC (R) PACKAGE
4
4
5
10
0%
5
3
5mV
6
2
500ns
3
2
6
Figure 28b. Settling Characteristics 0 V to –10 V Step
Upper Trace: Output of AD712 Under Test (5 V/Div)
Lower Trace: Amplified Error Voltage (0.01%/Div)
1
7
1
7
8
8
Figure 30. Board Layout for Guarding Inputs
5pF
1/2
AD712
HP2835
205V
VERROR 3 5
TEKTRONIX 7A26
OSCILLOSCOPE
PREAMP
INPUT SECTION
1MV
HP2835
0.47mF
200V
DATA
DYNAMICS
5109
0.47mF
4.99kV
4.99kV
–15V +15V
10kV
5-18pF
10kV
1.1kV
VIN
0.2-0.6pF
10kV
1/2
AD712
(OR EQUIVALENT
FLAT TOP
PULSE
GENERATION)
VOUT
5kV
0.1mF
10pF
0.1mF
–15V +15V
Figure 29. Settling Time Test Circuit
REV. B
–9–
20pF
AD712
D/A CONVERTER APPLICATIONS
VDD
The AD712 is an excellent output amplifier for CMOS DACs.
It can be used to perform both 2 quadrant and 4 quadrant operation. The output impedance of a DAC using an inverted
R-2R ladder approaches R for codes containing many 1s, 3R for
codes containing a single 1, and for codes containing all zero,
the output impedance is infinite.
R2A*
C1A
33pF
GAIN
ADJUST
OUT1
VREF
0.1mF
RFB
VDD
VIN
+15V
AD7545
R1A*
AGND
1/2
AD712
VOUTA
1/2
AD712
VOUTB
DGND
For example, the output resistance of the AD7545 will modulate between 11 kΩ and 33 kΩ. Therefore, with the DAC’s
internal feedback resistance of 11 kΩ, the noise gain will vary
from 2 to 4/3. This changing noise gain modulates the effect of
the input offset voltage of the amplifier, resulting in nonlinear
DAC amplifier performance.
*REFER TO
TABLE I
The AD712K with guaranteed 700 µV offset voltage minimizes
this effect to achieve 12-bit performance.
GAIN
ADJUST
ANALOG
COMMON
DB11–DB0
R2B*
VDD
C1B
33pF
RFB
VDD
OUT1
Figures 31 and 32 show the AD712 and AD7545 (12-bit
CMOS DAC) configured for unipolar binary (2-quadrant multiplication) or bipolar (4-quadrant multiplication) operation.
Capacitor C1 provides phase compensation to reduce overshoot
and ringing.
VIN
VREF
R1B*
AD7545
AGND
DGND
*REFER TO
TABLE I
0.1mF
ANALOG
COMMON
–15V
DB11–DB0
Figure 31. Unipolar Binary Operation
R1 and R2 calibrate the zero offset and gain error of the DAC.
Specific values for these resistors depend upon the grade of
AD7545 and are shown below.
Table I. Recommended Trim Resistor Values vs. Grades
of the AD7545 for VDD = +5 V
C1
33pF
KN/BQ/TD
LN/UD
GLN/GUD
R1
R2
500 Ω
150 Ω
200 Ω
68 Ω
100 Ω
33 Ω
20 Ω
6.8 Ω
R4
20kV 1%
+15V
0.1mF
R5
20kV 1%
RFB
VDD
OUT1
VREF
VIN
JN/AQ/SD
R2*
VDD
GAIN
ADJUST
Trim
Resistor
AD7545
R1*
AGND
DB11–DB0
1/2
AD712
DGND
R3
10kV 1%
VOUT
0.1mF
12
DATA INPUT
*FOR VALUES OF
R1 AND R2 SEE TABLE I
1/2
AD712
ANALOG
COMMON
–15V
Figure 32. Bipolar Operation
–10–
REV. B
AD712
Figures 33a and 33b show the settling time characteristics of the
AD712 when used as a DAC output buffer for the AD7545.
100
90
10
0%
500ns
DRIVING THE ANALOG INPUT OF AN A/D CONVERTER
An op amp driving the analog input of an A/D converter, such
as that shown in Figure 34, must be capable of maintaining a
constant output voltage under dynamically changing load conditions. In successive-approximation converters, the input current
is compared to a series of switched trial currents. The comparison point is diode clamped but may deviate several hundred
millivolts resulting in high frequency modulation of A/D input
current. The output impedance of a feedback amplifier is made
artificially low by the loop gain. At high frequencies, where the
loop gain is low, the amplifier output impedance can approach
its open loop value. Most IC amplifiers exhibit a minimum open
loop output impedance of 25 Ω due to current limiting resistors.
a. Full-Scale Positive Transition
STS
12/8
CS
HIGH
BITS
AO
GAIN
ADJUST
100
90
R/C
CE
AD574
REF IN
R2
100V
+15V
0.1mF
R1
100V
REF OUT
MIDDLE
BITS
LOW
BITS
BIP OFF
+5V
10
0%
500ns
610V
ANALOG
INPUT
b. Full-Scale Negative Transition
Figure 33. Settling Characteristics for AD712 with AD7545
The AD712C grade is specified at a maximum level of 4.0 µV
p-p, in a 0.1 Hz to 10 Hz bandwidth. Each AD712C receives a
100% noise test for two 10-second intervals; devices with any
excursion in excess of 4.0 µV are rejected. The screened lot is
then submitted to Quality Control for verification on an AQL
basis.
10VIN
+15V
20VIN
–15V
ANA
COM
DIG
COM
ANALOG COM
Figure 34. AD712 as ADC Unity Gain Buffer
A few hundred microamps reflected from the change in converter
loading can introduce errors in instantaneous input voltage. If
the A/D conversion speed is not excessive and the bandwidth of
the amplifier is sufficient, the amplifier’s output will return to
the nominal value before the converter makes its comparison.
However, many amplifiers have relatively narrow bandwidth
yielding slow recovery from output transients. The AD712 is
ideally suited to drive high speed A/D converters since it offers
both wide bandwidth and high open-loop gain.
All other grades of the AD712 are sample-tested on an AQL
basis to a limit of 6 µV p-p, 0.1 Hz to 10 Hz.
REV. B
0.1mF
–15V
NOISE CHARACTERISTICS
The random nature of noise, particularly in the 1/f region,
makes it difficult to specify in practical terms. At the same time,
designers of precision instrumentation require certain guaranteed maximum noise levels to realize the full accuracy of their
equipment.
1/2
AD712
OFFSET
ADJUST
–11–
AD712
PD711 BUFF
5V
100
1ms
100
90
90
10
10
0%
0%
500mV –10V ADC IN
200ns
Figure 37. Transient Response RL = 2 kΩ, CL = 500 pF
a. Source Current = 2 mA
ACTIVE FILTER APPLICATIONS
PD711 BUFF
In active filter applications using op amps, the dc accuracy of
the amplifier is critical to optimal filter performance. The
amplifier’s offset voltage and bias current contribute to output
error. Offset voltage will be passed by the filter and may be
amplified to produce excessive output offset. For low frequency
applications requiring large value input resistors, bias currents
flowing through these resistors will also generate an offset voltage.
100
90
10
0%
500mV
200ns
–5V ADC IN
b. Sink Current = 1 mA
Figure 35. ADC Input Unity Gain Buffer Recovery Times
DRIVING A LARGE CAPACITIVE LOAD
The circuit in Figure 36 employs a 100 Ω isolation resistor
which enables the amplifier to drive capacitive loads exceeding
1500 pF; the resistor effectively isolates the high frequency
feedback from the load and stabilizes the circuit. Low frequency
feedback is returned to the amplifier summing junction via the
low pass filter formed by the 100 Ω series resistor and the load
capacitance, CL. Figure 37 shows a typical transient response
for this connection.
In addition, at higher frequencies, an op amp’s dynamics must
be carefully considered. Here, slew rate, bandwidth, and
open-loop gain play a major role in op amp selection. The slew
rate must be fast as well as symmetrical to minimize distortion.
The amplifier’s bandwidth in conjunction with the filter’s gain
will dictate the frequency response of the filter.
The use of a high performance amplifier such as the AD712 will
minimize both dc and ac errors in all active filter applications.
4.99kV
30pF
+VIN
0.1mF
+ –
4.99kV
INPUT
TYPICAL CAPACITANCE
LIMIT FOR VARIOUS
LOAD RESISTORS
R1
C1 UP TO
2kV
10kV
20V
1500pF
1500pF
1000pF
1/2
AD712
100V
C1
OUTPUT
R1
0.1mF
– +
–VIN
Figure 36. Circuit for Driving a Large Capacitive Load
–12–
REV. B
AD712
SECOND ORDER LOW PASS FILTER
REF 20.0 dBm
OFFSET .0 Hz
10 dB/DIV
RANGE 15.0 dBm
0 dB
Figure 38 depicts the AD712 configured as a second order
Butterworth low pass filter. With the values as shown, the corner
frequency will be 20 kHz; however, the wide bandwidth of the
AD712 permits a corner frequency as high as several hundred
kilohertz. Equations for component selection are shown below.
TYPICAL BIFET
R1 = R2 = user selected (typical values: 10 kΩ – 100 kΩ)
C1 (in farads ) =
1.414
0.707
C2 =
(2π)( f cutoff )(R1)
(2π)( f cutoff )(R1)
AD712
C1
560pF
+15V
0.1mF
R1
20kV
VIN
R2
20kV
C2
280pF
SPAN 10 000 000.0 Hz
CENTER 5 000 000.0 Hz
ST .8 SEC
RBW 30 kHz
VBW 30 kHz
1/2
AD712
VOUT
Figure 39.
0.1mF
–15V
Figure 38. Second Order Low Pass Filter
An important property of filters is their out-of-band rejection.
The simple 20 kHz low pass filter shown in Figure 38, might be
used to condition a signal contaminated with clock pulses or
sampling glitches which have considerable energy content at
high frequencies.
The low output impedance and high bandwidth of the AD712
minimize high frequency feedthrough as shown in Figure 39.
The upper trace is that of another low-cost BiFET op amp
showing 17 dB more feedthrough at 5 MHz.
REV. B
–13–
AD712
+15V
0.1mF
+15V
0.1mF
VIN
0.001mF
A1
AD711
2800V
4.9395E–15
0.1mF
6190V
6490V
6190V
5.9276E–15
5.9276E–15
4.9395E–15
A
B
C
2800V
A2
AD711
D
0.1mF
–15V
100kV
*
*
*
VOUT
*
0.001mF
124kV
4.99kV
–15V
4.99kV
*SEE TEXT
Figure 40. 9-Pole Chebychev Filter
9-POLE CHEBYCHEV FILTER
REF 5.0 dBm
10 dB/DIV
Figure 40 shows the AD712 and its dual counterpart, the
AD711, as a 9-pole Chebychev filter using active frequency
dependent negative resistors (FDNR). With a cutoff frequency
of 50 kHz and better than 90 dB rejection, it may be used as an
antialiasing filter for a 12-bit Data Acquisition System with
100 kHz throughput.
As shown in Figure 40, the filter is comprised of four FDNRs
(A, B, C, D) having values of 4.9395 3 10–15 and 5.9276 3
10–15 farad-seconds. Each FDNR active network provides a
two-pole response; for a total of 8 poles. The 9th pole consists
of a 0.001 µF capacitor and a 124 kΩ resistor at Pin 3 of amplifier A2. Figure 41 depicts the circuits for each FDNR with the
proper selection of R. To achieve optimal performance, the
0.001 µF capacitors must be selected for 1% or better matching
and all resistors should have 1% or better tolerance.
START.0 Hz
RBW 300 Hz
MARKER 96 800.0 Hz
RANGE –5.0 dBm
–90 dBm
VBW 30 Hz
STOP 200 000.0 Hz
ST 69.6 SEC
Figure 42. High Frequency Response for 9-Pole
Chebychev Filter
+15V
0.1mF
0.001mF
R
1/2
AD712
0.1mF
1/2
AD712
0.001mF
–15V
1.0kV
R:
24.9kV FOR 4.9395E–15
29.4kV FOR 5.9276E–15
4.99kV
Figure 41. FDNR for 9-Pole Chebychev Filter
–14–
REV. B
AD712
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
0.390 (9.91)
8
0.005 (0.13)
MIN
0.055 (1.35)
MAX
5
0.250 0.310
(6.35) (7.87)
1
8
4
PIN 1
0.165 60.01
4.19 60.25
0.035 60.01
(0.890 60.25)
0.310 (7.87)
0.220 (5.59)
1
0.195 (4.95)
0.115 (2.93)
0.405 (10.29)
MAX
0.150
(3.81)
0.125 (3.18)
MIN
0.200 (5.08)
0.014 (0.36) 0.100 0.030 (0.76) SEATING
PLANE
0.023 (0.58) (2.54) 0.070 (1.78)
BSC
158
08
TO-99
(H-08A)
REFERENCE PLANE
0.1968 (5.00)
0.1890 (4.80)
0.2440 (6.20)
0.2284 (5.80)
4
0.305 (7.75)
0.335 (8.50)
0.335 (8.50)
0.370 (9.40)
5
0.040 (1.01) MAX
0.200
(5.1)
TYP
6
3
7
2
0.100
(2.54)
BSC
0.021 (0.53)
0.016 (0.41)
BASE & SEATING PLANE
0.045 (1.1)
0.020 (0.51)
5
1
4
PIN 1
8
BOTTOM VIEW
1
8
0.1574 (4.00)
0.1497 (3.80)
0.0688 (1.75)
0.0532 (1.35)
0.0098 (0.25)
0.0040 (0.10)
0.0500 0.020 (0.51)
SEATING (1.27) 0.013 (0.33)
PLANE BSC
0.034 (0.86)
0.028 (0.71)
0.0098 (0.25)
0.0075 (0.19)
0.0196 (0.50)
x 458
0.0099 (0.25)
88
08
0.050 (1.27)
0.016 (0.40)
458 BSC
EQUALLY SPACED
PRINTED IN U.S.A.
INSULATION
0.05 (1.27) MAX
0.008 (0.20)
0.015 (0.38)
158
08
SOIC
(R-8)
0.500 (12.70)
MIN
0.019 (0.48)
0.016 (0.41)
0.220 (5.59)
0.310 (7.87)
0.015 (0.38)
0.060 (1.52)
0.200 (5.08)
MAX
0.011 60.003
(0.204 60.081)
SEATING
PLANE
4
PIN 1
0.18 60.01
(4.57 60.76)
0.018 60.003 0.100 0.033 (0.84)
NOM
(0.460 60.081) (2.54)
TYP
5
0.25R
(0.64)
0.300 (7.62)
REF
0.125 (3.18)
MIN
0.185 (4.70)
0.165 (4.19)
C1020c–1–4/98
Cerdip
(Q-8)
Mini-DIP
(N-8)
REV. B
–15–