User's Guide SBAU206 – April 2015 ADS126xEVM-PDK ADS126xEVM-PDK This user's guide describes the operation and use of the ADS126x evaluation module (ADS126xEVM). The ADS1262 and ADS1263 are low-noise, low-drift 32-bit delta-sigma analog-to-digital converters (ADC) for precision industrial applications. The performance demonstration kit (PDK) is intended for prototyping and evaluating the ADS1262 and ADS1263. The ADS126xEVM-PDK includes the ADS126xEVM daughter card, MMB0 motherboard, A-to-B USB cable, 6-V wall-adapter power supply, and supporting software. This document includes a detailed description of the hardware and software, bill of materials, and schematic for the ADS126xEVM. Throughout this document, the terms ADS126xEVM, demonstration kit, evaluation board, evaluation module, and EVM are synonymous with the ADS126xEVM-PDK. The following EVM-compatible devices and related documents are available through the Texas Instruments website at www.ti.com. Related Documents Device Literature Number ADS1262 ADS1263 SBAS661 TPS79225 SLVS337B TPS72325 SLVS346C E2E is a trademark of Texas Instruments, Inc. Windows XP, Windows 7 are trademarks of Microsoft Corporation. X2Y is a registered trademark of X2Y Attenuators, LLC. All other trademarks are the property of their respective owners. SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 1 www.ti.com 1 2 3 4 Contents ADS126xEVM Overview .................................................................................................... 4 1.1 EVM Features ....................................................................................................... 4 1.2 Hardware Overview................................................................................................. 4 ADS126xEVM Hardware.................................................................................................... 5 2.1 Default Jumper and Switch Configuration ....................................................................... 5 2.2 Quick Reference .................................................................................................... 6 2.3 Power Supply........................................................................................................ 7 2.4 ADC Clock Source Options ...................................................................................... 11 2.5 Digital Interface, J1 ............................................................................................... 12 2.6 Analog Inputs ...................................................................................................... 13 ADS126xEVM Software ................................................................................................... 17 3.1 ADCPro and ADS126xEVM Plugin Installation................................................................ 17 3.2 Connecting the Hardware ........................................................................................ 17 3.3 Using ADCPro with the ADS126xEVM ......................................................................... 18 3.4 Using the ADS126xEVM Plugin ................................................................................ 20 ADS126xEVM Schematic and Bill of Materials ......................................................................... 31 4.1 Bill of Materials .................................................................................................... 31 List of Figures 1 ADS126xEVM Partitioning .................................................................................................. 4 2 ADS126xEVM connected to MMB0 motherboard ....................................................................... 4 3 Default Jumper and Switch Settings ...................................................................................... 5 4 Power Supply Circuitry Schematic 5 Power-Supply Circuitry (Default Jumper Settings) ...................................................................... 7 6 MMB0 Configuration for the 6-V Wall Adapter ........................................................................... 8 7 MMB0 Configuration for a Unipolar Bench Power Supply.............................................................. 9 8 MMB0 Configuration for a Bipolar Bench Power Supply .............................................................. 10 9 A) Schematic of ADS126xEVM Clocking Circuitry and B) Clocking Components on the ADS126xEVM ...... 11 10 Analog Input Support Circuitry on the ADS126xEVM ................................................................. 13 11 ADS126xEVM Ratiometric Connection Example ...................................................................... 15 12 J4 Thermocouple Input .................................................................................................... 16 13 Loading the ADS1262EVM Plugin in ADCPro 14 EVM Connection Status ................................................................................................... 18 15 ADS1262EVM Plugin Tabs ............................................................................................... 19 16 Loading a Test Plugin in ADCPro ........................................................................................ 19 17 Tab 1 Settings .............................................................................................................. 20 18 Tab 2 Settings .............................................................................................................. 21 19 Tab 3 Settings .............................................................................................................. 22 20 Tab 4 Settings .............................................................................................................. 23 21 Tab 5 Settings .............................................................................................................. 24 22 Tab 6 Settings .............................................................................................................. 25 23 Tab 7 Settings .............................................................................................................. 26 24 Tab 8: Register Map ....................................................................................................... 27 25 Tab 9: Register Map ....................................................................................................... 28 26 Tab 10: Extras / About ..................................................................................................... 29 27 Data Monitor Window ...................................................................................................... 30 28 Status Byte Error Pop-up .................................................................................................. 30 ........................................................................................ ......................................................................... 7 18 List of Tables 1 2 Factory Default Settings .................................................................................................... ADS126xEVM-PDK 5 SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated www.ti.com 2 Critical Connections ......................................................................................................... 6 3 J1, Serial Interface Header 4 ADS126x Analog Input Pin Functions ................................................................................... 14 5 ADS126xEVM Bill of Materials ............................................................................................... .......................................................................................... SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 12 31 3 ADS126xEVM Overview 1 www.ti.com ADS126xEVM Overview The ADS126xEVM-PDK is an evaluation module using the MMB0 hardware and ADCPro software platform for evaluation of the ADS1262 and ADS1263 (both referenced to as ADS126x in this document). The standalone ADS126xEVM is useful for prototyping designs and firmware. 1.1 EVM Features • • • • 1.2 Includes all required support circuitry for the ADS1262 and ADS1263 ADCPro evaluation software for Windows XP™ and Windows 7™ operating systems, with built-in analysis tools Configurable inputs, references, supplies, and clock sources Easily accessible signals through test points and headers Hardware Overview The EVM layout is partitioned as follows: the analog input/output (I/O) section, digital I/O header, power components, and clock circuitry. All these sections connect to the ADS126x TSSOP package located in the center of the EVM. Figure 1 visually identifies each of these areas on the EVM. Analog I/O Clock ADS126x Digital I/O Power Figure 1. ADS126xEVM Partitioning Figure 2 shows the EVM connected to the MMB0 motherboard. Figure 2. ADS126xEVM connected to MMB0 motherboard The MMB0 provides two main functions: 1. Provides power to the ADS126xEVM 2. Interfaces between ADCPro and the ADS126x. The default configuration of the MMB0 is sufficient to configure the ADS126x with a single supply. See Section 2.3.2 to configure the EVM with bipolar supplies. A schematic of the MMB0 motherboard is available at ftp://ftp.ti.com/pub/data_acquisition/ADCPro/Support/MMB0_Sch_RevD.PDF. The MMB0 is intended to be used with the accompanying EVM software and does not have additional resources to support the use as a firmware development platform. 4 ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Hardware www.ti.com 2 ADS126xEVM Hardware This section provides details about the ADS126xEVM hardware. 2.1 Default Jumper and Switch Configuration The ADS126xEVM is factory configured with the jumper and switch settings shown in Figure 3 and listed in Table 1. The ADS126xEVM operates with these default settings using a single supply and external crystal oscillator. ADS126x Figure 3. Default Jumper and Switch Settings Table 1. Factory Default Settings Name Default Setting JP1 Shorted Shorts IN4 to IN6 (for two-wire ratiometric measurements) JP2 Shorted Used in conjunction with S1 for selecting or inputting the master clock JP3 Shorted Connects IN5 to AVSS to setup a current-controlled reference voltage across R17 JP4 1-2, 3-4, and 5-6 shorted JP5 Shorted S1 1-2 (right) S2 2-3 and 5-6 (left) Function Power supply connections to the ADS126x Connects the thermocouple input J4.1 to AINCOM for biasing Used in conjunction with JP2 to select master clock source Selects unipolar or bipolar supplies for the ADS126x (the bipolar option requires an additional bench supply) NOTE: • • Shorted jumpers on JP4 are required to connect the ADS126x to AVDD, AVSS, and DVDD power supplies. These jumpers can be removed for measuring current, or for connecting an external power supply. The JP2, JP3, and JP5 jumpers are not required. Theses jumpers modify the analog input connections for biasing and ratiometric measurements. See Section 2.6 for more details. SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 5 ADS126xEVM Hardware 2.2 www.ti.com Quick Reference Table 2 provides a quick summary of the key connections necessary for EVM operation. This information is helpful when using an external processor or for monitoring EVM operation. Table 2. Critical Connections Function SPI Power Analog inputs 6 Header (Pin) Pin Name Description CS J1.7 CS Chip select SCLK J1.3 SCLK Serial clock DIN J1.11 DIN DOUT/DRDY J1.13 DOUT Data out DRDY J1.15 DRDY Data ready +3.3 V J5.9 +3.3V Digital supply Analog supply +5 V Data in J5.3 +5V Channels 0-5 J3.1-6 AIN0-AIN5 Analog or reference inputs Channels 6-7 J3.7-8 AIN6-AIN7 Analog inputs Channels 8-9 J4.2,1 AIN8, AIN9 Thermocouple or analog inputs Channel 10 J3.10 AINCOM ADS126xEVM-PDK Analog or common-reference input SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Hardware www.ti.com 2.3 Power Supply The ADS126x operates either from a single 5-V supply or from bipolar ±2.5V supplies. By default, the MMB0 and ADS126xEVM are configured for single 5-V supply operation using the included 6-V walladapter power supply. An additional –5-V supply voltage is required when using the ADS126xEVM with bipolar supplies. Configuring the EVM and MMB0 for each of these cases is demonstrated in Section 2.3.1 and Section 2.3.2. The ADS126xEVM is powered by the MMB0 motherboard, through the J5 header. The MMB0 is powered through the 6-V wall adapter connected to J2. The MMB0 does not use USB power. Additional supplies can be connected to the MMB0 through the J14 header. Figure 4 shows the relevant power supply circuitry on the ADS126xEVM. Supply Polarity Switch +5V AVDD 6 Pos 2 Pos 1 GND S2 5 3 4 U2 1 3 C27 1uF IN EN 1 3 5 Positive Supply 2 Negative Supply DVDD AVSS 2 4 6 DVDD 1 JP4 +3.3V CAS-220TB +5V AVSS AVDD Power Measurement or EXT Supply Jumpers +2.5V 5 4 2 OUT BYP GND C28 100nF TPS79225DBVT AVSS DVDD AVDD 2 AVDD GND GND 2 C32 1uF 3 IN EN C29 10uF -2.5V 5 4 1 OUT BYP GND D1 DDZ6V2B-7 C31 10uF GND1 GND2 GND GND GND AVSS C33 100nF TPS72325DBVT GND GND C30 10uF 1 U3 -5V GND +5V (-5V Supply must be supplied by user) GND +3.3V -5V 1 2 3 4 5 6 7 8 9 10 -5V Input Top and Bottom Side (Bottom Connects to MMB0) J5 DAUGHTER-POWER MMB0 Signals Signal Pin # +VA 1 -VA 2 +5VA 3 -5VA 4 DGND 5 AGND 6 +1.8VD 7 VD1 8 +3.3VD 9 +5VD 10 Figure 4. Power Supply Circuitry Schematic The JP4 jumpers are required to power the ADS126x. Removing these jumpers allows for an external power supply connection or an ammeter connection to monitor the supply currents. Mini-clip test points may also be used to connect to the ADS126xEVM supplies. Figure 5 shows the JP4 jumpers, switch S2, and the power-supply test points. Figure 5. Power-Supply Circuitry (Default Jumper Settings) SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 7 ADS126xEVM Hardware 2.3.1 www.ti.com Single 5-V Supply Configurations To operate the EVM with a single 5-V supply, first check that switch S2 is in the default position (switched to the left) and the JP4 jumpers are shorted as shown in Figure 5. Next, configure the MMB0 motherboard in one of the following ways: 2.3.1.1 6-V, Wall-Adapter Power Supply (Default Configuration) Make sure that the MMB0 jumpers J12 and J13B are shorted (default), as shown in Figure 6. In this configuration, when the 6-V wall adapter is connected to J2, the MMB0 board generates the 5-V analog supply and 3.3-V digital supply for the ADS126xEVM. +6V wall-adapter jack USB connector Shorted jumpers (J12, J13B) Figure 6. MMB0 Configuration for the 6-V Wall Adapter NOTE: For clarity, the ADS126xEVM daughter card is not shown in Figure 6, Figure 7, or Figure 8. The ADS126xEVM may need to be removed from the MMB0 motherboard to access the MMB0 jumpers. Power down the MMB0 board when mounting or removing the ADS126xEVM daughter card. 2.3.1.1.1 • • • 8 External Power-Supply Requirements Nom Output Voltage: 6 VDC Min Output Current: 500 mA Efficiency Level V NOTE: TI recommends using an external power supply that complies with applicable regional safety standards such as (by example) UL, CSA, VDE, CCC, PSE, and so forth. ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Hardware www.ti.com 2.3.1.2 Bench Power Supply To use the MMB0 with an external bench power supply, remove the J12 jumper and leave it open, as shown in Figure 7. Removing the jumper allows an external 5-V power supply to be connected to +5VA on the J14 terminal block. Jumper J13B connects +5VA to +5VD and must remain shorted. In this configuration, the MMB0 derives the 3.3-V digital supply for the ADS126xEVM from the 5-V bench supply, and the bench supply directly supplies the analog supply voltage for the ADS126xEVM. USB connector + ± Open jumper (J12) 5V Power Input Shorted jumper (J13B) Figure 7. MMB0 Configuration for a Unipolar Bench Power Supply SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 9 ADS126xEVM Hardware 2.3.2 www.ti.com Bipolar ±2.5-V Supplies Configuration To use the ADS126x with bipolar supplies, an external –5-V bench supply is required. If a negative supply is not available, a positive 5-V supply capable of sinking current can be connected with reversed polarity. First, configure the MMB0 in one of the configurations methods shown in Section 2.3.1. Next, connect a –5-V supply to the -5VA net on terminal block J14, as shown in Figure 8. After the MMB0 is configured, latch switch S2 (on the ADS126xEVM) into the 1-2 and 4-5 position (switched to the right) to select the bipolar supply. USB connector 5V + ± ± + Open jumper (J12) 5V Power Input Shorted jumper (J13B) Figure 8. MMB0 Configuration for a Bipolar Bench Power Supply NOTE: The ADS126xEVM uses the power supply connections from +5VA, -5VA, +3.3VD, and GND on the MMB0 board. MMB0 jumper J13A has no effect on the circuit behavior of the ADS126xEVM as long as no other supply is connected to +VA. Do not short jumper J13A when another supply is connected to +VA. 10 ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Hardware www.ti.com 2.4 ADC Clock Source Options The ADS126x requires a master clock to operate the delta-sigma modulator. The clock frequency, fCLK, is directly proportional to the modulator's sampling rate, fMOD (= fCLK/8). Consequently, the ADC output data rate follows the modulator sampling rate divided by the overall decimation ratio set by the digital filter. This clock can be supplied by the ADS126x internal oscillator, by the X1 crystal oscillator on the ADS126xEVM, or by an external clock source. The clock source is determined by switch S1 and jumper JP2. Figure 9 shows the relevant clocking circuitry on the ADS126xEVM. A) B) Figure 9. A) Schematic of ADS126xEVM Clocking Circuitry and B) Clocking Components on the ADS126xEVM Use one of the following clocking options: 1. Onboard 7.3728 MHz Crystal Oscillator (Default Configuration) The ADS126xEVM has an onboard crystal oscillator (component X1). The crystal oscillator clock is detected by the ADS126x when switch S1 is in the 1-2 position (switched to the right, as shown in Figure 9B). 2. ADS126x Internal 7.3728 MHz Oscillator The ADS126x selects the internal oscillator when no external clock is detected. To use this mode, ground the XTAL1/CLKIN input by switching S1 to the 2-3 position (switched to the left) and float the XTAL2 input by shorting jumper JP2. 3. External Clock Source If an alternate clock source or frequency is preferred, apply the external clock to the XTAL1/CLKIN input, and float XTAL2. The ADS126xEVM provides for this external clock connection. Remove jumper JP2 and apply the clock to the JP2 jumper posts. Configure switch S1 to the 2-3 position (switched to the left). The external clock source must have a frequency between 1 MHz and 8 MHz, and have a peak-to-peak amplitude equal to the DVDD supply voltage. SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 11 ADS126xEVM Hardware 2.5 www.ti.com Digital Interface, J1 The J1 header (top) and socket (bottom) provide access to the digital controls and serial data pins of the ADS126x. These signals can be connected to a development platform for software development. All logic levels are referenced to the digital supply voltage (the MMB0 provides a 3.3-V digital supply to the ADS126xEVM through pin J5.9). Table 3 describes the J1 serial interface pins. Table 3. J1, Serial Interface Header Function Signal Name Unused SPI clock SCLK Unused Serial port active low chip select (100-kΩ pull-up) Pin Number (J1) 1 2 3 4 5 6 CS 7 8 9 10 Serial port data input DIN 11 12 Serial port data output and data ready indicator (active low) DOUT/DRDY 13 14 Data ready indicator (active low) DRDY Unused Signal Name Function START Start conversion control (100-kΩ pull-up) GND Ground RESET/PWDN Reset (active low) or hold low to power-down the ADC (100-kΩ pull-up) Unused GND Ground Unused Unused 15 16 Unused 17 18 GND Ground Unused 19 20 SDA I2C data (for EEPROM) NOTE: SCL I2C clock (for EEPROM) Keep all connections to the ADS126xEVM as short as possible. If jumper wiring is used to connect a software development board to the ADS126xEVM, keep a ground connection (wire) between boards close to all of the digital signals (wires). A large loop area between ground and digital signals creates inductive connections and poor signal integrity. When probing SPI communications, check the signal integrity near the receiving end (that is, probe DIN at the ADS126x input, not at the SPI controller output). 12 ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Hardware www.ti.com 2.6 Analog Inputs The ADS126x has a total of 11 analog input pin: AIN0 through AIN9 plus a common reference input, AINCOM. This design allows the ADS126x to be configured for up to five differential input pairs, ten single-ended inputs referenced to a common voltage, or a combination of single-ended and differential inputs. The flexible input multiplexer of the ADS126x allows any two inputs to be selected for either the positive or negative ADC input. When measuring single-ended input signals, any input pin may be used as a common voltage reference. However, AINCOM is specially designated to serve this purpose because it provides a bias voltage (levelshift function) for floating sensors to meet the common-mode voltage requirements of the ADS126x inputs. All of the analog inputs to the ADC are pinned out on the ADS126xEVM. The supporting circuitry provides filtering and ratiometric connections for a variety of sensors. Additionally, a separate terminal block (J4) is provided for thermocouple inputs. Figure 10 shows the schematic of the ADS126xEVM analog input circuitry. IN1 IN0 R1 47 C1 47pF R2 NI GND R6 47 IN1 J2 1 IN0 2 IN1 3 IN2 4 IN3 5 IN4 AIN0 (EXT REF1 P) X2Y Capacitor C2 NI C3 100nF GND GND C4 47pF AIN1 (EXT REF1 N) IN2 IN2 6 IN5 7 IN6 8 IN7 9 AINCOM R8 47 C7 47pF R10 NI IN3 GND R12 47 AIN2 (EXT REF2 P) X2Y Capacitor C8 NI C9 100nF GND GND C11 47pF AIN3 (EXT REF2 N) 10 ED555/10DS TERMINAL BLOCK Top Side GND Ratiometric Connection Jumper 1 IN6 2 IN4 JP1 IN4 R16 47 1 IN0 2 IN1 3 IN2 4 IN3 5 IN4 6 IN5 7 IN6 8 IN7 R17 3.9k R17 sets up a 1.95V reference voltage with 500uA IDAC IN5 R19 620 AINCOM1 AINCOM C22 47pF AIN5 (EXT REF3 N) AVSS Connection Jumper JP3 R19 increases REF3N voltage to >0.3V when used with 500uA IDAC in single supply and ratiometric configurations AVSS IN6 R20 47 13 AIN6 (Test SIG P) X2Y Capacitor C24 NI C23 47pF GND 14 GND R18 47 2 1 10 12 C18 GND 100nF GND C21 47pF 9 11 AIN4 (EXT REF3 P) X2Y Capacitor C17 NI C16 47pF J3 15 C25 GND 100nF GND 16 GND C26 47pF 17 IN7 R21 47 AIN7 (Test SIG N) 18 20 DAUGHTER-ANALOG Bottom Side (Connects to MMB0) INPUT FILTERING REFOUT1 19 CM f-3dB = 72 MHz DM f-3dB = 16.9 kHz REFOUT GND MMB0 passes signals through to J10 2.2k @ 25°C t° RT1 R22 Thermistor (for CJC) R23 NI 12k R24 Configured for 250uA IDAC in single supply configuration (Install 0-Ohms in R22 & R24) IN6 IN7 NI R25 1.2k X2Y Capacitor R26 499 AIN8 C34 1nF J4 Thermocouple Input GND GND 2 1 R28 499 R31 NI ED555/2DS TERMINAL BLOCK Top Side C37 1nF C35 NI C36 100nF GND GND AIN9 FILTERING CM f-3dB = 319 kHz DM f-3dB = 1.59 kHz Cold Junction = GND GND 1 2 Sensor Bias Jumper AINCOM JP5 Figure 10. Analog Input Support Circuitry on the ADS126xEVM SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 13 ADS126xEVM Hardware 2.6.1 www.ti.com ADS126x Integrated Input Functions The ADS1262 and ADS1263 provide several integrated functions on the analog inputs to support many applications. Table 4 summarizes the functions available on each input pin. Table 4. ADS126x Analog Input Pin Functions 2.6.1.1 Input Pin ADC Input IDAC Output VBIAS Output External REF Input Test DAC Output GPIO AIN0 yes yes - REF1 P - - AIN1 yes yes - REF1 N - - AIN2 yes yes - REF2 P - - AIN3 yes yes - REF2 N - yes AIN4 yes yes - REF3 P - yes AIN5 yes yes - REF3 N - yes AIN6 yes yes - - yes yes AIN7 yes yes - - yes yes AIN8 yes yes - - - yes AIN9 yes yes - - - yes AINCOM yes yes yes - - yes ADC Inputs The ADS126x has a flexible input multiplexer with 11 analog inputs. Any of the inputs can connect to the positive input and any input can connect to the negative input. (Additionally, the ADS1263 has a second ADC with an independent flexible input multiplexer to all input pins). Configure the inputs to provide either single-ended or differential input measurements. The input multiplexer can also connect to several internal signals. The internal signals are the temperature sensor, test DAC, analog power supply ([AVDD – AVSS] / 4), and digital power supply ([DVDD – DGND] / 4). Use the internal signals for ADC and system functional verification or as part of an ADC diagnostic routine. 2.6.1.2 IDAC Output The ADS126x provides dual matched current sources (IDAC1 and IDAC2) for biasing of resistive temperature devices (RTDs), thermistors and other resistive based sensors. The IDACs can be independently programmed and can be connected to any analog input. Each IDAC is programmable over the range of 50 µA to 3000 µA. The internal reference must be enabled for IDAC operation. 2.6.1.3 VBIAS Output The analog power supply is either a single or bipolar supply. For single-supply operation, the level shift function (VBIAS) can offset the common input voltage on AINCOM to a midsupply voltage ([AVDD + AVSS] / 2). 2.6.1.4 External REF Input The ADC126x accepts external references (in addition to the internal and supply reference options). The external reference inputs are shared with pins AIN0 through AIN5. ADC2 (on the ADS1263) selects a different reference source other than the primary ADC. 2.6.1.5 Test DAC Output Inputs AIN6 and AIN7 are programmable to output the internal test DAC voltage. The test signal output is unbuffered; do not externally load. 2.6.1.6 GPIO Eight inputs (AIN3 through AINCOM) are configurable as general-purpose input/outputs (GPIO). The GPIO voltages are referenced to the analog power supply (AVDD and AVSS); therefore, the GPIOs must use 5-V logic. The GPIOs are useful for control of external devices, as well as reading external logic signals. 14 ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Hardware www.ti.com 2.6.2 Using the ADS126xEVM for Ratiometric Measurements Ratiometric measurements are often used with resistive-type sensors requiring a current excitation source (such as an RTD). The current is forced through the resistive sensor to generate a voltage signal for the ADC input. If the current source deviates from the programmed value (because of drift or noise), an apparent change in resistance is observed by the ADC. To correct for this error, the current source is also forced through a precision resistor to generate the ADC reference voltage. In this ratiometric configuration, a change in current directly affects the ADC input signal and reference voltage proportionally. Therefore, the ratio of the input signal to reference voltage remains constant for a given sensor impedance. A simple block diagram of a ratiometric connection, using a 3-wire RTD with the ADS126xEVM, is shown in Figure 11. The 3-wire RTD is connected to the J2 header on inputs IN7, IN6, and IN4. Two IDACs output 250 µA (each) on pins AINCOM and AIN3 of the ADS126x. Jumper wires then connect IN7 to COM, and IN6 to IN3. These jumper wires route the IDAC currents around the input filtering to prevent voltage drops in the input signal path. IDAC current flow thought the R17 resistor, between IN4 and IN5, to provide the ratiometric voltage reference. IDAC currents are routed to AVSS through JP3, or directly to ground by connecting another jumper wire between IN5 and GND. 3-Wire RTD COM AINCOM ADS126x IN7 AIN7 PGA IN6 AIN3 AIN4 IN4 500 uA Alternate Bias Connection REF JP1 IN3 IN5 ADC1 AIN6 AIN5 + R17 3.9k 1.95 V - JP3 GND + R19 620 0.31 V AVSS ADS126xEVM Figure 11. ADS126xEVM Ratiometric Connection Example NOTE: The purpose of R19 is to boost up the negative reference voltage when using a singlesupply configuration. However, the ADS126x allows for the negative reference voltage to be connected directly to AVSS (when used with a bipolar supply) or GND potential (when used with a single supply). Short R19 or replace with a 0-Ω resistor to allow additional headroom for the IDAC compliance voltage. Although this example shows a 3-wire RTD, the ADS126x can also support 2- or 4-wire RTDs. For a 2wire RTD, use JP1 to replace the IN4 connection. For a 4-wire RTD, remove the IN6 to IN3 jumper wire, remove the IN7 to COM jumper wire, and connect the additional RTD wire to COM. SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 15 ADS126xEVM Hardware 2.6.3 www.ti.com Thermocouple Input Terminal block J4, shown in Figure 12, connects to inputs AIN8 and AIN9 on the ADS126x. The terminal block is surrounded by a cutout ground plane polygon to provide partial thermal isolation for thermocouple inputs. Thermocouples can be biased either by enabling the VBIAS level shifter and shorting jumper JP5, or by enabling the 1-MΩ pull-up and pull-down resistors inside the ADS126x. Figure 12. J4 Thermocouple Input Cold junction compensation of the thermocouple is implemented by the thermistor on RT1 to measure the cold junction temperature. Install 0-Ω resistors on R22 and R24 (0603 surface-mount pads) to connect RT1 to inputs AIN6 and AIN7 on the ADS126x. R23 is in parallel with RT1 for linearization of the thermistor resistance versus temperature transfer function. NOTE: 2.6.4 Do not use the IN6 and IN7 inputs on terminal block J2 if components are soldered to R22 or R24. Interaction between components causes measurement error. X2Y® Capacitor Footprints Capacitors C2, C8, C17, C24, and C35 are unpopulated footprints reserved for 0603 X2Y capacitors. X2Y capacitors can replace the multiple capacitors (C1, C3, and C4 for example) required for common-mode and differential filtering. In addition to the board space saved by using X2Y, these capacitors have lower ESL and excellent common-mode capacitor matching. 16 ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Software www.ti.com 3 ADS126xEVM Software This section explains setup and use of the ADS126xEVM software. Software setup requires installing ADCPro (a tool used to acquire and analyze ADC data), and installing an EVM specific plugin to use within ADCPro. Download the ADCPro user's guide from http://www.ti.com/lit/ug/sbau128c/sbau128c.pdf. 3.1 ADCPro and ADS126xEVM Plugin Installation 1. Install ADCPro Download the ADCPro installer from http://www.ti.com/adcpro. The ADCPro Hardware and Software Installation Manual provides a step-by-step installation procedure. Install ADCPro first before installing the ADS126xEVM plugin. 2. Install the ADS126xEVM Plugin Download the ADS126xEVM plugin installer from http://www.ti.com/tool/ads1262evm-pdk or http://www.ti.com/tool/ads1263evm-pdk. Run the ADS126x plugin installer after installing ADCPro. NOTE: The ADS126xEVM plugin installer runs an additional installation for the USBStyx driver required to communicate with the MMB0. If the software is unable to connect to the EVM, this driver may not have properly installed. This driver may be reinstalled with one of the installers located at ftp://ftp.ti.com/pub/data_acquisition/ADCPro2/misc/drivers/. Use the installer version (32- or 64-bit) that corresponds to the version of your operating system. 3.2 Connecting the Hardware After ADCPro and the ADS126xEVM plugin have been installed, connect the hardware, and then run ADCPro. To connect the hardware, follow these steps: 1. If disconnected, connect the ADS126xEVM daughter card to the MMB0 motherboard while powered off (as shown in Figure 2). 2. Check and configure jumper and switch settings on the MMB0 and ADS126xEVM, as described in Section 2.3. 3. Connect any sensors or external test circuitry to the ADS126xEVM. 4. Connect the USB cable from the MMB0 to the computer. 5. Power up the MMB0 (and ADS126xEVM) with the included wall adapter or an external bench supply. 6. After powering up the MMB0 and ADS126xEVM, power up any other external circuitry. 7. Run ADCPro and follow the steps in Section 3.3 to communicate with the ADS126xEVM. SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 17 ADS126xEVM Software 3.3 www.ti.com Using ADCPro with the ADS126xEVM For more information about ADCPro than is provided in this document, refer to the ADCPro User's Guide, SBAU128. This section covers only the functionality of the ADS126xEVM plugin. After the hardware is connected, powered up, and ADCPro is running, follow these steps to establish communication with the ADS126xEVM: 1. Load the ADS126xEVM plugin by clicking ADS126XEVM from the EVM file menu shown in Figure 13. This step can be repeated to reload the plugin. The plugin may need to be reloaded in the case of a communication failure or if power is cycled on the EVM hardware. Figure 13. Loading the ADS1262EVM Plugin in ADCPro 2. Wait for the Connected to EVM status seen in Figure 14. If the connection fails, reset the hardware either by pushing the reset button in the upper right corner of the MMB0 or by cycling MMB0 power. If a connection cannot be established after resetting the MMB0, refer back to Section 3.1 and Section 3.2 for the required drivers and hardware connections. Figure 14. EVM Connection Status 18 ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Software www.ti.com 3. Configure the ADS126x. The ADS126xEVM plugin is divided into ten tabs, as shown inFigure 15. Clicking on a tab changes the displayed controls. The controls on each tab are described in Section 3.4. 1 Input MUX 7 Data \ MODE 2 Reference 8 Calibration 3 Digital Filter 9 Register Map 4 IDAC / Sensor Bias 5 GPIO 10 Extras / About 6 Test DAC Figure 15. ADS1262EVM Plugin Tabs 4. Select a test plugin from the Test file menu, as shown in Figure 16. This step may precede steps 1 to 3, but is required before acquiring data in the next step. Figure 16. Loading a Test Plugin in ADCPro 5. Acquire data by clicking the Acquire or Continuous button (previously shown in Figure 14). These buttons are only operational when both the EVM and test plugins are loaded. Clicking Acquire captures a single block of data. Clicking Continuous captures blocks of data repeatedly. The block size is configured in the test plugin. 6. Use the test plugin functions as described in the ADCPro User's Guide, SBAU128, to analyze the ADC conversion data. SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 19 ADS126xEVM Software 3.4 www.ti.com Using the ADS126xEVM Plugin This section describes the controls in the ADS126xEVM plugin. Additional details about specific ADS126x functions can be found in the ADS1262 and ADS1263 data sheet, SBAS661. 3.4.1 Tab 1: Input MUX The controls on tab 1 select the ADC inputs from the internal multiplexer (mux) and control the PGA settings. Click the radio buttons to independently select the positive (AINPx) and negative (AINNx) ADC inputs. Clicking the TEMP, AVDD, DVDD, or TDAC special function inputs selects that function for both inputs, and configures the PGA as recommended. Note that the ADC2 radio buttons are only visible when an ADS1263EVM is connected. Clicking the AINCOM button enables the VBIAS level shifter. Both the VBIAS level shifter and Chop functions can be configured on tab 1 and tab 4 (IDAC \ Sensor Bias). To test the ADC noise performance, select the same input signal for AINP and AINN to internally short the ADC inputs. Remember to set a proper common-mode input voltage by applying an external midsupply voltage or by using the VBIAS function on AINCOM, as shown in Figure 17. 1 Input MUX Figure 17. Tab 1 Settings 20 ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Software www.ti.com 3.4.2 Tab 2: Reference Figure 18 shows the tab used to configure the ADCx reference source. The voltage reference source is selected from the ADCx REF Source drop-down menu. When using an external source for ADC1, the positive and negative reference inputs must be specified by the REFP and REFN drop-down menus. Selecting the Invert ADC1 REF Inputs checkbox swaps the positive and negative reference inputs, and allows for fully flexible reference source inputs. 2 Reference Figure 18. Tab 2 Settings When using an external reference source for ADC1, also make sure that the ADC1 REF Voltage field is matched to the applied reference voltage to allow ADCPro to correctly convert the output data from codes to volts. The internal reference can be disabled when an external referenced is used; however, the internal reference must be enabled to use the IDACs. The ADC2 Reference Settings are only visible when an ADS1263EVM is connected. SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 21 ADS126xEVM Software 3.4.3 www.ti.com Tab 3: Digital Filter Tab 3 contains the filter and data rate selection controls, as shown in Figure 19. 3 Digital Filter Figure 19. Tab 3 Settings The ADC1 Filter Settings section controls both the digital filter type and the data rate for ADC1. When the FIR filter is selected, data rates are limited to frequencies that support 50-Hz or 60-Hz line cycle rejection. Note that because of speed limitations within the firmware, the 19.2 kSPS and 38.4 kSPS data rates are only available when Data Collection Mode is set to ADC1 on Tab 7 (Data \ MODE). The ADC2 Filter Settings controls are shown only when an ADS1263EVM is connected. The SINC3 filter is the only filter available for ADC2. NOTE: Data from ADC2 are only collected when Data Collection Mode is set to ADC1 + ADC2 on Tab 7 (Data \ MODE). ADC2 Data Rate must be at least ½ the ADC1 Data Rate setting because the firmware only polls for new ADC2 data when an ADC1 conversion completes. Setting the ADC2 Data Rate much slower than ½ the ADC1 Data Rate may require a much longer collection time. ADC1 and ADC2 do not sample simultaneously. Changing ADC filter and data rate settings, the chopping settings on tab 4 (IDAC \ Sensor Bias), or the fCLK control, updates the Filter Response plot. This plot can be scaled by the controls below the plot or by clicking and typing a new value into an existing axis value. NOTE: Make sure that the fCLK frequency input is correct (there is no need to modify fCLK when using the ADS126x internal oscillator or the ADS126xEVM's default X1 crystal). The fCLK frequency affects the calculated ADC1 Data Rate and ADC2 Data Rate indicators that are also used by the software when acquiring data, plotting the filter response, or calculating the FFT in the MultiFFT test plugin. 22 ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Software www.ti.com 3.4.4 Tab 4: IDAC / Sensor Bias Figure 20 shows the IDAC \ Sensor Bias tab controls. The IDAC Configuration controls configure the IDAC direction, magnitude, and rotation. The IDACs require the internal reference to be enabled on tab 2 (Reference). 4 IDAC / Sensor Bias Figure 20. Tab 4 Settings The Sensor Bias Settings controls are used to enable burnout current sources or bias resistor connections prior to ADC1 (or ADC2) for detecting sensor open circuits or biasing floating sensors. Only use burnout current sources to verify the sensor connection. For best results, disable the burnout current source after the sensor connection is verified and before measuring the sensor output. Make sure to account for the analog filter settling time when enabling or disabling the burnout current source. The Additional Settings controls configure other sensor bias-related functions: Input Chop— enables or disables the global input chop feature of the ADS126x. When enabled, input chopping reduces offset and offset drift errors. Settling Delay— configures the initial conversion delay before ADC1 begins converting. The default settling delay provides time for PGA1 to settle when a step input occurs. AINCOM Bias— enables or disables the mid-supply level-shift function on the AINCOM pin Input Chop and AINCOM are duplicated on tab 1 (Input MUX) for quick access. NOTE: The software does not allow for simultaneous GPIO, Test DAC, IDAC, or VBIAS functions to be enabled on the same pin. SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 23 ADS126xEVM Software 3.4.5 www.ti.com Tab 5: GPIO Tab 5, shown in Figure 21, controls the GPIO functions available on the AIN3-AIN9 and AINCOM pins. The GPIO Functions controls select the GPIO direction and logic value. Note that the GPIO logic levels are referenced to the analog supply voltage (5V-logic). The Value radio buttons serve dual purposes as both controls and indicators. Value indicates the logic value when configured as an input, and controls the logic value when configured as an output. The Value buttons are grayed out until the GPIO function is enabled on the respective channel. Controlling the GPIO value does nothing when configured as an input. 5 GPIO Figure 21. Tab 5 Settings Clicking Read GPIO or modifying any of controls on this tab reads the GPIODAT register and updates all value indicators. NOTE: The GPIODAT register bits corresponding to GPIO inputs are read-only, and the GPIODAT register bits corresponding to GPIO outputs are write-only. Therefore, you cannot read back any GPIO output values from the GPIODAT register. Store a copy of the GPIODAT register settings in memory (as this software does) in order to recall the GPIO output configuration from memory. NOTE: The software does not allow for simultaneous GPIO, Test DAC, IDAC, or VBIAS functions to be enabled on the same pin. 24 ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Software www.ti.com 3.4.6 Tab 6: Test DAC The Test DAC tab, as shown in Figure 20, controls the internal test DAC and is used to verify ADC functionality by providing a known dc input voltage. The test DAC has two resistor divider taps that select a fraction of the supply voltage. To use the test DAC, first select the Pos. Test Signal Supply Ratio and Neg. Test Signal Supply Ratio settings, and then connect the test DAC to ADC1, ADC2, or both, with the Test DAC to ADCx controls or with the MUX controls on tab 1 (Input MUX). Additionally, the test DAC voltages are provided as outputs on pins AIN6 and AIN7 to be measured externally. 6 Test DAC Figure 22. Tab 6 Settings The Test DAC Calculator is provided to calculate the test DAC output and ADC input voltages based on the supply ratios, AVDD, AVSS, and PGA gain settings. As an example, using the following settings: • Pos. Test Signal Supply Ratio = 0.525 • Neg. Test Signal Supply Ratio = 0.475 • Test DAC to ADC1 = Input to ADC1 (to select the Test DAC as the input source for ADC1) • PGA1 Gain = 1 V/V (on tab 1) For a supply voltage of 5 V (AVDD – AVSS), the test DAC outputs (5 V) × (0.525 V – 0.475 V) × (1 V/V) = 0.25 V to ADC1. To output or measure the test DAC voltage externally, set the Test Signal Outputs drop-down menu to Connected to AIN6/AIN7. NOTE: The test DAC is susceptible to power supply noise. Allow a sufficient margin of error when verifying ADC conversion results with the test DAC. Create a ratiometric measurement of the test DAC by selecting the analog supply as the voltage reference source for the ADC. Then the matching input and reference noise cancels in the ADC conversion result. NOTE: The software does not allow for simultaneous GPIO, Test DAC, IDAC, or VBIAS functions to be enabled on the same pin. SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 25 ADS126xEVM Software 3.4.7 www.ti.com Tab 7: Data \ MODE (ADS1263 only) Use tab 7, as shown in Figure 23, to enable or disable ADC2 data collection, and select whether ADC1 or ADC2 data are displayed in the test plugin. This tab is only visible when the ADS1263EVM is connected. 7 Data \ MODE Figure 23. Tab 7 Settings To start ADC2 conversions and read back data from ADC2, Data Collection Mode must be set to ADC1 + ADC2. This setting enables the ADC Data to Test Plug-in control. The ADC Data to Test Plug-in controls whether data from ADC1 or ADC2 appear in the test plugin for evaluation. ADC1 and ADC2 data do not have the same LSB size and likely contain different sample sizes; therefore, the software is only able to evaluate one data set at a time. If ADC1 is selected in the ADC Data to Test Plug-in section, ADC1 data appear in the test plugin panel to the right, and the ADCx Data graph displays data from ADC2. Conversely, if ADC2 is selected in the ADC Data to Test Plug-in control, ADC2 data appear in the test plugin panel, and ADC1 data appear in the ADCx Data graph. However, it is possible to switch between ADC1 and ADC2 data sets in the test plugin without having to reacquire new data. After acquiring ADC1 and ADC2 data (with Data Collection Mode set to ADC1 + ADC2), switch ADC Data to Test Plug-in to the other ADC. A button with the text Swap EVM & Test Plugin Data? appears. Click the Swap EVM & Test Plugin Data? button and then click Acquire. This procedure takes the existing ADC data sets and swaps them between the ADCx Data graph and the test plugin. NOTE: In ADCPro, when Data Collection Mode is set to ADC1 + ADC2, the data rate for ADC1 must be greater than or equal to two times the ADC2 data rate. The firmware must poll the STATUS byte for new ADC2 data every time new ADC1 data are ready. ADC1 data are ready when the DRDY signal goes low, but there is no DRDY signal to indicate that new ADC2 is ready. As a result of this behavior, ADC2 data are lost if this requirement is not satisfied. 26 ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Software www.ti.com 3.4.8 Tab 8: Calibration Tab 8 (shown in Figure 24) allows for reading and writing of the offset and full-scale (gain) calibration registers. The ADC2 offset and gain calibration registers are only available when the ADS1263EVM is connected. 8 Calibration Figure 24. Tab 8: Register Map Program the calibration coefficients manually into the registers, or send the corresponding SPI calibration command. Click an SPI command button to run the selected calibration routine. During a calibration routine, CAL in Progress? lights up to show that the calibration process is ongoing. If the calibration completes successfully, CAL Completed? lights up. If CAL Completed? does not light up, run the calibration again. The calibration coefficients are converted to their practical units in the Offset and Gain indicators. Note that the units of Offset can be changed from uV to mV as needed. Calibration is not required; however, calibration improves overall ADC accuracy by about an order of magnitude. SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 27 ADS126xEVM Software 3.4.9 www.ti.com Tab 9: Register Map Use tab 9 (shown in Figure 25) to read and display the current ADS126x register settings. This tab is useful to see how device settings in the ADCPro software are stored in the ADS126x device registers. 9 Register Map Figure 25. Tab 9: Register Map Reading back the ADC registers is recommended in all applications to make sure that the ADC settings are correct and match software assumptions. When the Register Map tab is selected or the Refresh Register Map button is clicked; all the device registers are read, the Register Map table is updated, and all ADC controls (on all tabs) are updated. The RESET button reverts all register settings back to the ADCPro nominal values. NOTE: The RESET button reverts all ADS126x register settings to a nominal state, as determined by ADCPro. This nominal state programs the MODE0, MODE1, MODE2, and ADC2CFG (when applicable) registers to nondefault ADS126x values (indicated by asterisks in the register map table). To revert all register settings back to the true ADS126x default values, use the RESET pin control button on tab 10 (Extras / About). Device settings such as the conversion control and STATUS/CRC byte configurations are enforced by software to ensure proper communication between hardware and firmware. The power-on reset (POR) function is also helpful in verifying correct device operation. The POR button, at the bottom of this tab, displays the current value of the POR bit in the POWER register. When clicked, the POR button toggles the value of the POR bit. Save the register settings to a text file with the Save to File button. Recall register settings with the Load from File button. Use this register map text file to document a particular setup. Reference this text file during development or support on the E2E™ Precision Data Converter Forum. 28 ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Software www.ti.com 3.4.10 Tab 10: Extra / About Tab 10 (Figure 26) is the last page with several useful controls. 10 Extras / About Figure 26. Tab 10: Extras / About The Documentation section of this tab provides quick access to support documents. Product Page, Data Sheet, and User's Guide connect to the latest online documentation. Schematic opens a local copy of the ADS126xEVM schematic. The Pin Controls section is used to control the RESET/PWDN and START pin logic levels. Clicking on any of these buttons toggles the logic levels, with the exception of the RESET button. The RESET button pulses the RESET/PWDN pin and resets all register settings back to their default values. The Software INFO section provides additional information about the software and hardware, as well as some other useful diagnostic tools. • Acquire Alert is a programmable acquisition-time alert. A pop up alerts the user when a data acquisition is estimated to take longer than the programmed alert value. The pop up notifies the user of the estimated acquisition time and provides the option to continue or cancel the acquisition. Cancelling an acquisition in progress requires resetting the hardware and reloading the EVM plugin. Long acquisition periods are possible because of the very low data rates of the ADS126x and large allowable block sizes in ADCPro. • Collection Info shows information about the number of samples collected from ADC1 and ADC2. If data acquisition seems to be taking longer than expected, check that the actual number of samples being collected accounts for the additional time. The number is slightly larger than the block size requested in the test plugin. Reduce the number of samples or increase the ADC data rates to reduce acquisition time. The acquisition time may be longer than the total number of samples divided by the data rate because the data is first collected into MMB0 memory, then transferred to ADCPro using USB, and finally processed in ADCPro before it is displayed. SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 29 ADS126xEVM Software • www.ti.com View Data reveals a data monitor that shows the raw ADC codes along with the STATUS and CHECKSUM/CRC bytes, as shown in Figure 27. Figure 27. Data Monitor Window • View Errors reveals a STATUS byte error indicator that ORs all of the STATUS byte error flags to check if any errors occurred in the previous acquisition, as shown in Figure 28. This window automatically appears when an error flag is found in the acquired data set. Switching to the View Data window is useful to see when this error first appeared in the collected data. Figure 28. Status Byte Error Pop-up 30 ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated ADS126xEVM Schematic and Bill of Materials www.ti.com 4 ADS126xEVM Schematic and Bill of Materials A complete schematic for the ADS126xEVM is appended to this user's guide. The bill of materials is provided in Table 5. Gerber files are available on request. Please email [email protected] or visit the E2E Community Forums and ask for details on how to receive the files. 4.1 Bill of Materials NOTE: All components should be compliant with the European Union Restriction on Use of Hazardous Substances (RoHS) Directive. Some part numbers may be either leaded or RoHS. Verify that purchased components are RoHS-compliant. (For more information about TI's position on RoHS compliance, see the http://www.ti.com.) Table 5. ADS126xEVM Bill of Materials (1) Item No. Qty 1 11 2 9 3 Value Ref Des Description Manufacturer Part Number -5V Input, PC TEST POINT MINIATURE SMT AINCOM, AVDD, AVSS, DVDD, GND, GND, GND, IN0, IN1, REFOUT Keystone Electronics 5015 47 pF C1, C4, C7, C11, C16, C21-23, C26 CAP, CERM, 47 pF, 50V, NP0, 1%, 0603 TDK C1608C0G1H470F080AA 5 (1) NI C2, C8, C17, C24, C35 CAP, NI, X2Y 4 5 0.1 uF C3, C9, C18, C25, C36 CAP, CERM, 100 nF, 50V, NP0, +/-5%, 1206 TDK C3216C0G1H104J160AA 5 1 4,700 pF C5 CAP, CERM, 4.7 nF, 50V, NP0, 5%, 0603 TDK C1608C0G1H472J080AA 6 6 1 uF C6, C10, C12, C13, C27, C32 CAP, CERM, 1 uF, 16V, X7R +/-10%, 0603 TDK C1608X7R1C105K080AC 7 2 33 pF C14, C15 CAP, CERM, 33 pF, 50V, NP0, +/-5%, 0402 Yageo CC0402JRNPO9BN330 8 2 10,000 pF C19, C20 CAP, CERM, 0.01 uF, 50V, X7R, +/-10%, 0402 Yageo CC0402KRX7R9BB103 9 2 0.1 uF C28, C33 CAP, CERM, 100 nF, 50V, X7R +/-10%, 0603 TDK C1608X7R1H104K 10 3 10 uF C29-31 CAP, CERM, 10 uF, 16V, X7R +/-20%, 1206 TDK C3216X7R1C106M 11 2 1,000 pF C34, C37 CAP, CERM, 1 nF, 100V, NP0, 1%, 0603 TDK C1608C0G2A102F080AA 12 1 D1 DIODE, ZENER, 6.2V, 500mW, SOD-123 Diodes Inc. DDZ6V2B-7 13 1 J1 (TOP SIDE) HEADER, 20POS 10x2, 100mil, SMD, GOLD Samtec TSM-110-01-L-DV-P 14 2 J1 (BOTTOM SIDE), J3 CONN, FEMALE, 20POS DL, 100mil, SMD, GOLD Samtec SSW-105-22-F-D-VS-K 15 1 J2 TERMINAL BLOCK, 3.5MM, 10POS, PCB On Shore Technology ED555/10DS 16 1 J4 TERMINAL BLOCK, 3.5MM, 2POS, PCB On Shore Technology ED555/2DS 17 1 J5 (TOP SIDE) CONN, HEADER, 10POS 5x2, 100mil, SMT, GOLD Samtec TSM-105-01-L-DV-P 18 1 J5 (BOTTOM SIDE) CONN, RECPT, 10POS, 100mil, SMT, GOLD Samtec SSW-105-22-F-D-VS-K 19 4 JP1, JP2, JP3, JP5 (ALL TOP SIDE) CONN, HEADER, 2POS, 100mil, T/H, GOLD Samtec HTSW-102-07-G-S 20 1 JP4 CONN, HEADER, 6POS, 100mil DBL, SMD, GOLD Samtec TSM-103-01-L-DV-P 21 14 47 Ohms R1, R6-9, R11-16, R18, R20, R21 RES, 47 Ohm, 1%, 1/10W, 0603 Panasonic ERJ-3EKF47R0V 22 6 (1) NI R2, R10, R22, R24, R27, R31 RES, NI, 0603 23 3 100 kOhms R3-5 RES, 100k Ohm, 5%, 1/10W, 0603 Panasonic ERJ-3GEYJ104V 24 1 3.9 kOhms R17 RES, 3.9K Ohm, 1/10W, 0.05%, 0603 Susumu RG1608N-392-W-T1 This component is not installed. SBAU206 – April 2015 Submit Documentation Feedback ADS126xEVM-PDK Copyright © 2015, Texas Instruments Incorporated 31 ADS126xEVM Schematic and Bill of Materials www.ti.com Table 5. ADS126xEVM Bill of Materials (continued) Item No. Qty Value 25 1 620 Ohms R19 RES, 620 Ohm, 0.11%, 1/10W, 0603 Panasonic ERA-3APB621V 26 1 12 kOhms R23 RES, 12k Ohm, 0.1%, 1/16W, 0603 TE Connectivity 7-1676481-8 27 1 1.2 kOhms R25 RES, 1.2K Ohm, 1/10W, 0.1%, 0603 Panasonic ERA-3ARB122V 28 2 499 Ohms R26, R28 RES, 499 Ohm, 0.1%, 1/10W, 0603 Panasonic ERA-3AEB4990V 29 2 2.7 kOhms R29, R30 RES, 2.7k Ohm, 5%, 1/10W, 0603 Panasonic ERJ-3GEYJ272V 30 1 0 Ohms R32 RES, 0 Ohm, 1/10W, 0603 Panasonic ERJ-3GEY0R00V 31 1 2.2k @ 25°C RT1 Thermistor NTC, 2.2k Ohm, 1%, 0805 Vishay NTCS0805E3222FMT 32 1 S1 SWITCH, SLIDE, SPDT, GULLWING Copal Electronics CAS-120TB 33 1 S2 SWITCH, SLIDE, DPDT, GULLWING Copal Electronics CAS-220TB 34 7 SH-J1, SH-J2, SH- SHUNT, 100mil, GOLD, BLACK J3, SH-J4, SH-J5 3M 969102-0000-DA 35 1 U1 IC, ADC, Delta-Sigma, 32-bit, 38kSPS Texas Instruments ADS1262IPW (2) 36 1 U2 IC, REG, LDO, 2.5V, 100mA, SOT23-5 Texas Instruments TPS79225DBVT 37 1 U3 IC, REG, LDO, -2.5V, 0.2A, SOT23-5 Texas Instruments TPS72325DBVT 38 1 U4 IC, EEPROM, 256 kBIT, 400 kHz, 8TSSOP Microchip Technology 24AA256-I/ST 39 1 X1 CRYSTAL, 7.3728 MHz, 18 pF, T/H ECS Inc. ECS-73-18-10X (2) 32 Ref Des Description Manufacturer Part Number Installed for the ADS1262EVM. The ADS1263IPW is installed for the ADS1263EVM. ADS126xEVM-PDK SBAU206 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated 1 2 3 4 COR1 R1 PIR101 47 PIR102 PIR202COR2 R2 NI GND PIR201 COJ2 J2 NLIN1 IN1 COR6 R6 47 PIR602 1 PIJ201 IN0 PI N201 PIR601 2 PIJ202 IN1 COIN2 IN2 3 PIJ203 IN2 4 PIJ204 IN3 5 PIJ205 IN4 PIJ206 6 IN5 PIR10COR10 2 R10 7 PIJ207 IN6 NI 8 PIJ208 IN7 9 PIJ209 AINCOM NLIN2 IN2 X2Y Capacitor COC2 C2 PIC20A NI AIN1 (EXT REF1 N) X2Y Capacitor COC8 C8 PIC80A NI NLREFOUT REFOUT GND PIC1 01 47pF COC10 PIC1001 C10 1uF PIC1002 AIN3 (EXT REF2 N) PIR1202 START Ratiometric Connection Jumper 1 IN6 2 IN4 PIJP102 1 IN0 2 IN1 3 IN2 PIJ301 B PIJ302 PIJ303 4 IN3 5 IN4 PIJ304 PIJ305 6 PIJ306 IN5 7 PIJ307 IN6 8 PIJ308 IN7 COR17 R17 3.9k R17 sets up a 1.95V reference voltage with 500uA IDAC NLIN5 IN5 PIR1902 PIA NCOM10 10 620 PIR1901 AINCOM COC22 C22 PIC2201 47pF PIC2202 11 12 8PIU108 REFOUT 21 AIN0 PIU1021 NLAIN0 AIN0 9PIU109 START 12PIU1012 14PIU1014 SCLK DGND PIU101818 17 BYPASS PIU1017 DIN COR20 R20 47 PIR2002 GND 5 PIJ105 NL\CS CS COC23 C23 17 PIJ3017 PIC2601 GND NLIN7 IN7 COR21 R21 47 PIR2101 18 GND PIREFOUT10 CM f-3dB = 72 MHz DM f-3dB = 16.9 kHz REFOUT COX1 X1 COS1 S1 PIC1402 CAS-120TB Clock Select Switch t° RT1 GND SDA GND 20 PIJ1020 INT/EXT Clock Jumper AVDD B DAUGHTER-SERIAL Top and Bottom Side (Bottom Connects to MMB0) 5 PIS205 3 4 PIS204 GND 1 Positive Supply 1 COU2 U2 PIC2701 PIC2702 3 PIU203 IN EN DVDD COAVSS AVSS PIAVD 01 PIJP402 3 PIJP403 CODVDD DVDD PIAVS 01 4 PIJP404 5 Negative Supply PIDVD 01 6 PIJP405 PIJP406 COJP4 JP4 +3.3V CAS-220TB 1 PIU201 2 PIJP401 2 PIS201 +5V AVSS COAVDD AVDD PIS203 Pos 1 Power Measurement or EXT Supply Jumpers +2.5V 5 OUT PIU205 4 BYP PIU204 2 GND PIU202 TPS79225DBVT PIC2802 PIC2801 COC28 C28 100nF GND COU3 U3 -5V 2 PIU302 COC32 C32 1uF NI PIC3201 3 PIU303 PIC320 COR26 R26 499 PIR2602 AVDD AVSS PIC2901 PIC2902 PIC30 1 PIC30 2 COC29 C29 10uF COC30 C30 10uF DVDD PIC3101 COC31 C31 PIC3102 10uF C AVDD PID102 PID101 COD1 D1 DDZ6V2B-7 2 PIJ402 COR28 499 PIR2801 R28 PIR2802 PIR3102 EN -2.5V 5 OUT PIU305 4 BYP PIU304 1 GND PIU301 GND GND GND AVSS PIC3 02 C33 COC33 PIC3 01 100nF AIN8 PIR2601 GND IN TPS72325DBVT X2Y Capacitor PIC3401 COC34 C34 PIC3402 1nF PIC3701 COC37 C37 PIC3702 1nF PIC3602 PIC3601 COC36 C36 100nF GND COC35 C35PIC350A NI GND COGND1 GND1 GND PIC350G PIC350B GND +3.3V COGND2 GND2 PIGND101 PIGND201 GND GND PIR2702 COR27 R27 AIN9 NI PIR2701 COU4 U4 1 A0 2 3 PIU403 A2 4 PIU404 VSS PIU401 COR31 R31 FILTERING NI CM f-3dB = 319 kHz DM f-3dB = 1.59 kHz PIR3101 GND3 COGND3 1 2 Sensor Bias Jumper PIJP501 PIJP502 AINCOM COJP5 JP5 1 19 PIJ1019 GND (-5V Supply must be supplied by user) GND GND 18 PIJP202 GND PIC240B IN7 PIR2401 Cold Junction = GND PIGND301 17 2 PIJ1018 COS2 S2 2 MMB0 Signals Signal Pin # +VA 1 -VA 2 +5VA 3 -5VA 4 DGND 5 AGND 6 +1.8VD 7 VD1 8 +3.3VD 9 +5VD 10 +5V PIR3202 COR32 R32 0 +3.3V PI05V Input01 PIJ501 PIJ502 PIJ503 PIJ504 PIJ50 PIJ506 PIJ507 PIJ508 PIJ509 PIJ501 Top and Bottom Side (Bottom Connects to MMB0) J5 COJ5 3 DAUGHTER-POWER PIR3201 PIU402 A1 PIR2902 8 VCC PIU408 7 WP PIU407 6 SCL PIU406 5 SDA PIU405 PIR2901 COR29 R29 2.7k PIR3002 COR30 R30 2.7k PIR3001 NLSCL SCL NLSDA SDA D 24AA256-I/ST EEPROM GND (Used by MMB0 only) GND -5V CO05V Input -5V Input 1 2 3 4 5 6 7 8 9 10 D 16 PIJ1016 PIJ1017 IN6 GND ED555/2DS TERMINAL BLOCK Top Side 15 PIJ1015 SCL COC15 C15 PIC1501 33pF PIR2202 PIR2402 1 PIJ401 COR15 47 R15 PIR1502 PIC1502 COC14 C14 PIC1401 33pF 3 PIJP201 1 PIS103 GND PIR2501 Thermocouple Input PIR1501 13 PIJ1013 14 PIJ1014 ECS-73-18-10X PIX102 COJP2 JP2 Pos 2 COR23 R23 NI 12k R24 COR24 COJ4 J4 NL\DRDY DRDY COR14 47 PIR1402 Supply Polarity Switch GND PIR2502 R14 PIR1401 1 MMB0 passes signals through to J10 Configured for 250uA IDAC in single supply configuration COR25 R25 (Install 0-Ohms in R22 & R24) 1.2k NLDOUT0D\R\D\Y\ DOUT/DRDY 11 PIJ1011 12 GND COC27 C27 1uF PIR2302 COR13 47 R13 PIR1302 +5V AIN7 (Test SIG N) 20 PIRT102 PIR1301 PIJ1012 GND PIS202 19 PIR2201 9 10 PIJ1010 NLDIN DIN 6 PIS206 PIC240G PIR2102 PIJ3019 PIR2301 MMB0 Signals Signal Pin # CNTL 1 GPIO0 2 CLKX 3 DGND 4 CLKR 5 GPIO1 6 FSX 7 GPIO2 8 FSR 9 DGND 10 DX 11 GPIO3 12 DR 13 GPIO4 14 *INT 15 SCL 16 TOUT 17 DGND 18 GPIO5 19 SDA 20 7 PIJ107 PIX101 47pF INPUT FILTERING CORT1PIRT10 6 PIJ106 PIJ109 PIC1301 COC13 C13 PIC1302 1uF X2Y Capacitor COC24 C24 PIC240A NI COC25 C25 GND 100nF COREFOUT1 REFOUT1 Thermistor (for CJC) 2.2k @ 25°C NL\RESET0PWDN R9 COR9 47 RESET/PWDN PIR901 PIR902 COR11 47 R11 PIR1101 PIR1102 8 PIJ108 COC12 PIC1201 C12 1uF PIC1202 2 COC19 COC20 C19 PIC1901 C20 PIC2001 0.01uF PIC1902 0.01uF PIC2002 3 PIJ103 DVDD AVSS AIN6 (Test SIG P) 16 PIJ3016 COR22 R22 COR7 47 R7 PIR701 PIR702 4 PIJ104 PIS102 AVDD A 2 PIJ102 NLSCLK SCLK RESET/PWDN 15 XTAL1/CLKIN PIU1015 DRDY COJ1 J1 1 16 XTAL2 PIU1016 DOUT/DRDY PIR502 PIJ101 19 DVDD PIU1019 CS PIR402 DIGITAL PIR2001 PIC2302 47pFPIC2502 PIC2602 COC26 PIC2501 C26 DAUGHTER-ANALOG Bottom Side (Connects to MMB0) NLAIN1 AIN1 AVSS PIC2301 PIJ3020 NLAIN2 AIN2 20 RESET/PWDN PIU1020 PIR302 NLSTART START 22 AIN1 PIU1022 AVSS Connection Jumper 15 PIJ3015 C NLAIN3 AIN3 PIR501 GND 13 PIJ3013 PIJ3018 24 AIN3 PIU1024 PIR401 COR3 R4 COR4 R5 COR5 R3 100k 100k 100k R19 increases REF3N voltage to >0.3V when used with 500uA IDAC in single supply and ratiometric configurations NLIN6 IN6 PIJ3012 14 PIJ3014 NLAIN4 AIN4 AIN5 ADS126xIPW AIN5 (EXT REF3 N) PIR1802 25 AIN4 PIU1025 AINCOM PIR301 COJP3 JP3 COR19 R19 COAINCOM1 AINCOM1 PIJ3010 PIC2101 47pF COR18 R18 47 PIR1801 2 PIJP302 1 PIJP301 9 PIJ309 PIJ3011 GND NLAIN5 AIN5 23 AIN2 PIU1023 11PIU1011 AIN4 PIR1701 NLAIN6 AIN6 26 PIU1026 DVDD PIS101 (EXT REF3 P) PIC1601 COC16 C16 X2Y Capacitor COC17 C17 PIC170A NI PIC1602 47pFPIC1802 COC18 C18 PIC170G GND GND PIC2102 COC21 PIC1801 100nF PIC170B C21 PIR1702 27 AIN6 PIU1027 AVSS 10PIU1010 DRDY COJ3 J3 AIN9 AVDD SCLK COJP1 JP1 COR16 R16 47 PIR1601 PIR1602 NLAIN7 AIN7 7PIU107 DOUT/DRDY13PIU1013 PIJP101 NLIN4 IN4 28 AIN7 PIU1028 6PIU106 CS AVSS DIN GND AIN8 4PIU104 CAPP COC5 C5 PIC501 4.7nF PIC502 5PIU105 CAPN PIC80B COC11 C11 COR12 R12 47 PIR1201 AVSS PIC80G GND 3PIU103 COC6 C6 PIC601 1uF PIC602 AIN2 (EXT REF2 P) PIC701 COC7 C7 PIC702 47pF PIC902 C9 COC9 PIC1 02 PIC901 100nF PIR10 1 2PIU102 NLAINCOM AINCOM 10 PIJ2010 ED555/10DS TERMINAL BLOCK Top Side NLAIN9 AIN9 GND 47 PIR802 GND 1PIU101 PIC20B AVDD COR8 R8 PIR801 NLIN3 IN3 NLAIN8 AIN8 PIC20G GND 100nF PIC402 PIC301 COC4 C4 PIC401 47pF COU1 U1 2 A AIN0 (EXT REF1 P) PIC101 COC1 C1 PIC10247pF PIC302 C3 COC3 1 PI N101 6 ANALOG COIN1 IN1 NLIN0 IN0 5 Designed for:Public Release Mod. Date:12/31/2014 Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this Project: ADS126xEVM specification or any information contained therein. Texas Instruments and/or its licensors do not Sheet Title: EVM Schematic Sheet:1 of 1 warrant that this design will meet the specifications, will be suitable for your application or fit for Size: B Schematic: 6580279 Rev: A any particular purpose, or will operate in an implementation. Texas Instruments and/or its Assembly Variant:[No Variations] licensors do not warrant that the design is production worthy. You should completely validate File: ADS126xEVM_RevA1_Schematic.SchDoc and test your design implementation to confirm the system functionality for your application. Contact: http://www.ti.com/support 4 5 6 http://www.ti.com © Texas Instruments 2014 STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES 1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein. Acceptance of the EVM is expressly subject to the following terms and conditions. 1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software 1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned, or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production system. 2 Limited Warranty and Related Remedies/Disclaimers: 2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License Agreement. 2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as mandated by government requirements. TI does not test all parameters of each EVM. 2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM, or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day warranty period. 3 Regulatory Notices: 3.1 United States 3.1.1 Notice applicable to EVMs not FCC-Approved: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to incorporate such items in a finished product and software developers to write software applications for use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter. 3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant: CAUTION This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Interference Statement for Class A EVM devices NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. SPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER FCC Interference Statement for Class B EVM devices NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 3.2 Canada 3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210 Concerning EVMs Including Radio Transmitters: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Concernant les EVMs avec appareils radio: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Concerning EVMs Including Detachable Antennas: Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Concernant les EVMs avec antennes détachables Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur 3.3 Japan 3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に 輸入される評価用キット、ボードについては、次のところをご覧ください。 http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified by TI as conforming to Technical Regulations of Radio Law of Japan. If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of Japan to follow the instructions below with respect to EVMs: 1. 2. 3. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of Japan, Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to EVMs, or Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan. SPACER SPACER SPACER SPACER SPACER 【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの 措置を取っていただく必要がありますのでご注意ください。 1. 2. 3. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用 いただく。 実験局の免許を取得後ご使用いただく。 技術基準適合証明を取得後ご使用いただく。 なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。 上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ ンスツルメンツ株式会社 東京都新宿区西新宿６丁目２４番１号 西新宿三井ビル 3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page 電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page SPACER 4 EVM Use Restrictions and Warnings: 4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS. 4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information related to, for example, temperatures and voltages. 4.3 Safety-Related Warnings and Restrictions: 4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or property damage. If there are questions concerning performance ratings and specifications, User should contact a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit components may have elevated case temperatures. These components include but are not limited to linear regulators, switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the information in the associated documentation. When working with the EVM, please be aware that the EVM may become very warm. 4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the dangers and application risks associated with handling electrical mechanical components, systems, and subsystems. User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees, affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or designees. 4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal, state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local requirements. 5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as accurate, complete, reliable, current, or error-free. SPACER SPACER SPACER SPACER SPACER SPACER SPACER 6. Disclaimers: 6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS. 6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF THE EVM. 7. USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES, EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED. 8. Limitations on Damages and Liability: 8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS, LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED. 8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT. 9. Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s) will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s), excluding any postage or packaging costs. 10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas, without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas. Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief in any United States or foreign court. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated spacer IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated