Shoulder HDF1178AS7 This specification shall cover the characteristics of saw filter with hdf1178a used for the page system Datasheet

规格书编号 :
SPEC NO :
产品 规 格书
SPECIFICATION
CUSTOMER 客 户:
PRODUCT 产 品:
SAW FILTER
MODEL NO 型 号:
HDF1178A SMD-7
MARKING 印 字:
HDF7G26
PREPARED 编 制:
CHECKED 审 核:
APPROVED 批 准:
D A T E 日 期:
2010-03-29
客户确认 CUSTOMER RECEIVED:
审核 CHECKED
批准 APPROVED
日期 DATE
无锡市好达电子有限公司
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 1 of 9
SAW FILTER
HDF1178A S-7
更改历史记录
History Record
更改日期
Date
www.shoulder.cn
规格书编号
Spec. No.
产品型号
Part No.
客户产品型号
Customer No.
Tel:0755-82916880 Fax:0755-82916881
更改内容描述
Modify Content
E-mail:[email protected]
备注
Remark
Page 2 of 9
SAW FILTER
HDF1178A S-7
1. SCOPE
This specification shall cover the characteristics of SAW filter with HDF1178A used for the
page system.
2. ELECTRICAL SPECIFICATION
Maximum Input Power
DC voltage
Storage Temperature Range
Operation Temperature Range
+10dBm
10V
-45℃ to +85℃
-40℃ to +85℃
2.2 Electronic Characteristics
Operating temperature range: T = –40 °C ... +85 °C
Terminating source impedance: ZS = 150 Ω
Terminating load impedance: ZL = 150Ω
Parameter
Center Frequency
Insertion loss(1158.12---1198.12 MHz)
-1.5dB Bandwidth
Passband ripple
Min.
1176.12
Typical.
1178.12
3.5
51
1.5
Rejection:
50 MHz—1096 MHz
1260 MHz—2000 MHz
40
40
Group Delay Variation
19
Temperature Coefficient
Package Size
32
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
Max.
1180.12
4.5
Unit
MHz
dB
MHz
2.0
dB
25
ns
ppm/°C
SMD-7
E-mail:[email protected]
Page 3 of 9
SAW FILTER
HDF1178A S-7
3.Typical Frequency Response
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 4 of 9
SAW FILTER
HDF1178A S-7
4.DIMENSION
Marking:HDF7G26
HD: Brand
F : Filter
7 : SMD-7
G26 : No.
5. ENVIRONMENTAL CHARACTERISTICS
5-1 High temperature exposure
Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions
for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2.
5-2 Low temperature exposure
Subject the device to -40℃ for 16 hours. Then release the device into the room conditions
for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2.
5-3 Temperature cycling
Subject the device to a low temperature of -40℃for 30 minutes. Following by a high
temperature of +85℃ for 30 Minutes. Then release the device into the room conditions
for 24 hours prior to the measurement. It shall meet the specifications in 2.2.
5-4 Resistance to solder heat
Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for
10±1 sec. Then release the device into the room conditions for 4 hours. The device shall
meet the specifications in 2.2.
5-5 Solderability
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 5 of 9
SAW FILTER
HDF1178A S-7
Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95%
area of the terminals must be covered with new solder. It shall meet the specifications in
2.2.
5-6 Mechanical shock
Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device
shall fulfill the specifications in 2.2.
5-7 Vibration
Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude
of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in 2.2.
6. REMARK
6.1 Static voltage
Static voltage between signal load & ground may cause deterioration &destruction
of the component. Please avoid static voltage.
6.2 Ultrasonic cleaning
Ultrasonic vibration may cause deterioration & destruction of the component. Please
avoid ultrasonic cleaning
6.3 Soldering
Only leads of component may be soldered. Please avoid soldering another part of
component.
7. Packing
7.1 Dimensions
(1) Carrier Tape: Figure 1
(2) Reel: Figure 2
(3) The product shall be packed properly not to be damaged during transportation and storage.
7.2 Reeling Quantity
1000 pcs/reel 7’’
3000 pcs/reel 13’’
7.3 Taping Structure
(1) The tape shall be wound around the reel in the direction shown below.
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 6 of 9
SAW FILTER
HDF1178A S-7
(2) Label
Device Name
User Product Name
Quantity
Lot No.
(3) Leader part and vacant position specifications.
8. TAPE SPECIFICATIONS
8.1 Tensile Strength of Carrier Tape: 4.4N/mm width
8.2 Top Cover Tape Adhesion (See the below figure)
(1) pull off angle: 0~15º
(2) speed: 300mm/min.
(3) force: 20~70g
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 7 of 9
SAW FILTER
HDF1178A S-7
[Figure 1] Carrier Tape Dimensions
[Unit:mm]
W
F
E
P0
P1
P2
D0
D1
t1
t2
A
B
12.00
±0.30
5.50
±0.10
1.75
±0.10
4.00
±0.10
4.00
±0.10
2.00
±0.10
Ø1.50
Ø1.5
±0.25
0.31
±0.05
1.30
±0.10
3.4
MAX.
3.4
MAX
[Figure 2]
[Unit:mm]
A
www.shoulder.cn
B
C
D
Tel:0755-82916880 Fax:0755-82916881
E
W
E-mail:[email protected]
t
r
Page 8 of 9
SAW FILTER
Ø330
±1.0
www.shoulder.cn
HDF1178A S-7
Ø100
±0.5
Ø13
±0.5
Ø21
±0.8
Tel:0755-82916880 Fax:0755-82916881
2
±0.5
13
±0.3
E-mail:[email protected]
3
max.
1.0
max.
Page 9 of 9
Similar pages